Search Documents

By W. M. Middleton

The exploiting of geothermal steam is a new endeavor in this country and is for that matter a very new science in the world. With the majority of steam wells in the world having been drilled during the last twelve years relatively little experience and knowledge has been gained that can guide us as compared to the techniques the oil and gas producers have developed for their use. We few technical personnel associated with the field find it a continuous challenge to understand and explain what effects or causes the various unusual phenomenon experienced. We have had unending discussions attempting to formulate pet theories which we can use as guides. We know, so the geologists tell us, that the source of the heat is from the hot magmatic core of the earth. Theory has it that the magma is cooling off and that hot gases are given off as this magma cools and shrinks. In volcanic' areas along fault lines where the magma reaches closer to the surface than in other areas, there is a higher concentration of gas evolution; consequently, geyser or geothermal areas are developed. As these hot gases rise toward the surface they encounter various minerals, including overlying bodies of water. It is into these underground lakes that our wells are penetrating. As the heat enters these lakes it spreads out by conduction, convection and water migration. We can strike this hot water over quite large areas in many of the geothermal fields. At present there is one anomaly to this in the United States as there is in Italy where our wells do not penetrate a hot water lake. This is at The Big Geysers in California. Here superheated steam is produced with a heat content, so high that it could not have been boiled off of a fresh water pool. This puzzled us until last year when a well was completed into a large body of brine in the Imperial Valley. This brine exists at close to 500°F and at a hydrostatic pressure sufficient to preclude any boiling. It is now believed by some of us that a similar pool of brine must exist below The Big Geysers area, from which the steam is emanating. If there is such a brine pool, it offers a plausible explanation of the high-heat content, for brine boils at a higher temperature than fresh water. I am now beginning to think that a similar brine pool may exist under all the geothermal basins for if it is under two of them, it is highly probable that it is under the others. The partial understanding of what we are drilling toward, and formulating a theory to explain its behavior helps guide us in our steam well drilling.

Jan 1, 1963

By James E. Myers

This study is a survey of the current "state-of-the-art" of commercially-available sonar tools to monitor the true shape of man-made cavities within the Hutchinson Salt of south-central Kansas. The work entailed ferreting out the available information, most of which is proprietary in nature; then examining actual existing conditions and arriving at a reasonable scientific evaluation of the method. Our studies were confined to one LPG field and two brine well operations in south-central Kansas. No field testing of any devices was performed, only questioning user firms, and studying cores, logs, and sonar surveys graciously made available by the companies we have contacted. Since these data are still somewhat proprietary, the company participants have asked that their company names be omitted from this presentation.

Jan 1, 1973

By R. R. Klimpel

The process of flotation is an extremely important solids separation technique employed in a wide variety of industrial process applications. Froth flotation is practiced in the coal industry to recover fines produced during the mining and cleaning of coal. A recent review article by Aplan (1) covers the processing variables encountered in the flotation of coal and the variety of chemicals and operating conditions which affect recovery. Numerous engineering and scientific studies have been performed with the goal of providing semifundamental laws of flotation behavior for improved screening of flotation chemicals, better equipment scale-up factors, etc. Often the results of such work are expressed in the form of mathematical models (e.g. 2, 3, 4, 5, 6) which are potentially useful for evaluating (simulating) on paper such alternatives as possibles process operating or configuration changes, the effects of ore and reagent changes, etc. It appears to be commonly accepted that a complete scientific/engineering characterization of flotation is immensely complicated and not sufficiently developed at the present to accurately predict (or understand) many important industrial facets of flotation. Thus, one is often reduced to detailed experimental characterization in both the laboratory and plant in order to fully evaluate flotation changes or alternatives. It is the purpose of this paper to describe a method of batch laboratory data characterization that is useful in evaluating flotation chemical reagents including froth flotation of coal. The approach consists of running a series of time-recovery curves in a batch float cell followed by the computer curve fitting of this data to a series of mathematical models based on semi-physical reasoning. The unknowns or parameters of these models are then optimally chosen so as to best fit the experimental data. It has been found in both coal and mineral systems that changes in reagent type, concentration, system pH, grind, etc. cause very consistent and logical changes to

Jan 1, 1979

By Tom L. Enos

Increased production through the plant was limited due to thickener circuit constraints. To overcome these constraints and maximize plant throughput to match grinding circuit capability, two options were considered: A. Adding 2000 TPD CIL circuit to operate in parallel with the existing CCD circuit. B. Adding a CIL circuit to treat the entire 4600 TPD while retaining some thickeners for tailings thickening. Option B was selected based on simplified plant operations, reduced operating costs, minimal capital requirements, reduced solution losses, and bullion grade improvement.

Jan 1, 1989

By U. Thorley

This paper presents an overview of surface mining activity in the Canadian oil sands and how the mine operators interact with the province of Alberta's Mine Financial Security Program (MFSP), which took effect April 1, 2011. The MFSP approach to reclamation assurance results in the government of Alberta sharing a portion of reclamation liability through the majority of an oil sand mine's life. In order to determine the potential fiscal magnitude of this shared liability, an examination of the expected costs of oil sands reclamation activities through a study of corporate asset retirement obligation (ARO) liabilities and other corporate disclosures is presented. The province of Alberta's Environmental Protection Security Fund (EPSF), which formerly secured oil sands mine reclamation activities is discussed. Reclamation costs in the oil sands are poorly understood. The MFSP provides what it characterizes as a conservative estimate of C$75,000/ha, while corporate disclosures by Canadian Oil Sands Ltd. place expected costs at C$180,000/ha. There is significant risk associated with the apparent uncertainty surrounding reclamation costs.

Jan 1, 2012

By JoAnn Silverstein, Eric A. Marchand

Competition between Thiobacillus ferrooxidans and non-iron-oxidizing heterotrophic bacteria was induced by the addition of glucose to a co-culture of T. ferrooxidans and A. acidophilum in an oxygen-limited environment. Iron oxidation was inhibited as dissolved oxygen was used preferentially for glucose metabolism. Furthermore, as the water became anoxic, glucose was consumed along with the oxidized iron species (Fe3+) during iron respiration resulting in a pH increase from 2.0 to 4.0. Results suggest that biologically mediated acidification of drainage water can be reversed by dispersion of an easy to degrade, soluble, and inexpensive carbon source such as glucose into the subsurface.

Jan 1, 2000

By K. A. Natarajan, K. S. N. Murthy

Growth of Thiobacillus ferrooxidans on pyrite mineral surfaces and in 9K leach media was studied through estimation of bacterial protein in the different phases. Bacterial attachment was found to be governed by particle size of the mineral, period of incubation and by stationary or agitation conditions used during incubation. Increased bacterial growth in the liquid as well as on the solid phase was observed with decreasing particle size and increasing incubation periods. Increased bacterial attachment to pyrite mineral surfaces was observed to promote iron dissolution.

Jan 1, 1993

By S. E. Valji

Clay slurries are normally dewatered using flocculents like sulfuric acid or aluminum sulfate. This type of flocculation is based on the electrolytic mechanism. For certain clay dewatering applications, this method of flocculation is unsatisfactory. Flocculation, based on the bridging mechanism, using organic polymers has been utilized to overcome such problem situations. This method of flocculation offers solutions not possible by previous methods. Normally these flocculents are used to assist dewatering. In this case, not only is dewatering promoted, but also further processing is assisted by a change in the dilatant character of the filter cake that is formed. Discharge of filter cake is easier, extrusion of filter cake on to conveyor dryer is possible or improved, and heat transfer and drying rates of the extruded filter cake are substantially higher. Both natural and synthetic organic polymers have been utilized for this purpose. Selection, application techniques, and economics are described.

Jan 1, 1965

By R. C. Bunge

A magnetogravimetric separation is the consequence of two competing forces with opposing directions, i.e., magnetic buoyancy and gravitation (or centrifugal force). While magnetic buoyancy is a function of particle volume, gravitational force depends on particle mass, thus permitting a separation according to specific gravity. Since magnetic buoyancy is not a phenomenon of common knowledge, this chapter is meant to briefly introduce the theory of magnetogravimetric separations. A particle that is suspended in a magnetic fluid which is exposed to an inhomogeneous magnetic field experiences a repulsive force -the so called magnetic buoyancy. In order to illustrate this effect, an analogy with the more familiar hydrostatic buoyancy is drawn. Hydrostatic buoyancy occurs due to unsymmetrical pressure distribution 'above' and 'below' a suspended particle (fig. 1).

Jan 1, 1990

By K. N. Han

Coal is becoming increasingly important as a major energy source in the face of the world's depleting energy mainly based on oil reserves. Coal is by far the most abundant fossil fuel both in the United States and abroad. Currently, because of increased mine mechanization, the fineness of preparation plant feed is increasing. Further, in the future as the grade of coal diminishes and the sulfur content increases, upgrading preparation of coal is very important. Because the density of coal is less than that of rock materials that occur as impurities, coal is separated from such waste largely by gravity-controlled processes for particle size between 5 inches and 28 mesh. If the size of coal particles is below 28 mesh, froth flotation is a good method for upgrading fine coal. Previously, numerous investigators have tried to upgrade coal values by froth flotation(1-16) and have achieved moderate success. However, the recovery and grade of coals in the concentrates are not always satisfactory, especially when the particle size is small. In general, when the size of coal is below 100 mesh, the above methods suffer from poor grade and low recovery. The reason for this is that as size decreases, the effects of gravity diminish, and other forces take effect.

Jan 1, 1985

Coal waste materials inhibit direct vegetation establishment due to adverse physical and chemical properties, particularly low water retention and high potential acidity. The Moss # I coal refuse pile is located in Dickenson County, Virginia, and was idled in the late 1980&apos;s with little topsoil resource available for final closure. The refuse was acidic (Total-S = .. 38%; pH = 3.6), black, high (70%) in coarse fragments, and had a low water holding capacity (4.5% in < 2.0 mm fraction). A small plot experiment was established on the refuse pile to evaluate the influence of liming rates (50% and 100% of lime req.) and topsoil thickness (15, 30 and 60 cm) on vegetative growth and leachate quality. Liming and topsoil amendment increased the surface soil pH from < 4.0 to > 6.0 over a two-year period, which resulted in greater vegetative cover and biomass than the control plots. All topsoil treatments resulted in greater vegetative cover and biomass than plots treated with lime only due to improved surface soil physical and chemical properties. A topsoil treatment of 60 cm gave the thickest vegetative cover and biomass yield. Such a treatment, however, would be cost-prohibitive at this location. Application of 27 Mg ha-1 of lime to the refuse surface along with 15 cm of topsoil produced acceptable two-year vegetative cover and biomass, and appeared to be the optimal treatment for this particular situation. Both liming and topsoil had no affect on leachate pH and the electrical conductivity in leachates collected below the plots. This suggests that surface revegetation will have little effect on the quality of water draining through the pile, so long term water treatment requirements may not be reduced by successfully revegetating the pile surface.

Jan 1, 1999

By T. Vandergrift, J. Sturgill, W. Gerhard, J. Carrick

As surface minable coal is depleted, many operators look to high-wall mining to extend reserve life. Recent advances in highwall mining equipment have greatly improved productivity, clean coal recovery, and attainable penetration beneath the highwall. Somewhat lagging have been systematic design approaches for ensuring web pillar and overall highwall stability. This paper presents an overview of the design, planning, and field performance of a multiple-seam highwall mining application in southwest Wyoming. The safety and efficiency obtained to date is attributable to the careful geotechnical and operational planning described herein. Field confirmation of performance and suggestions for improvement are also discussed.

Jan 1, 2004

By Francis B. Gularte, James E. Monsees, John-Paul Whyte, Gary E. Taylor

In a short section of the Los Angeles Metro Rail system approximately 222.5 m (730 ft) of 6.4 m (21 ft) diameter twin-tube tunnels separated by a 1.8 m (6 ft) narrow pillar were designed to pass under a major eight lane freeway and a metropolitan intersection with only 3.7 m (12 ft) to 5.8 m (19 ft) of loose fill and alluvium cover. The design considerations and the chemical grouting program used to stabilize the alluvial materials is discussed. Also included is a discussion of the novel shield used for tunnel excavation and the effects of the subsequent fire.

Jan 1, 1991

By Y. Numata

2-Mercaptobenzothiazole (MBT) is a heterocyclic-mercaptan and belongs to a group of molecules containing nitrogen and sulfur as electron donor atoms. MBT has been employed as a collector in flotation under names of MBT, Captax, and Flotagen. It is a major constituent of reagents in the 400 series of the American Cyanamid Co. Current applications of the reagent include flotation of copper minerals, tarnished or oxidized lead, copper activated sphalerite, and nickel ores. It has been used successfully in the flotation of pyrite in acid circuits in the range of 4 to 5.

Jan 1, 1990

By Ronald Allum

Arizona leads all other states in the value of gemstones produced with an annual production which exceeds $3,000,000. Gemstones are an important component of the mineral wealth of the State. Turquoise, peridot, chrysocoll a, petrified wood, fire agate and crystallized mineral specimens are among the gemstones commercially mined. Numerous additional deposits are operated by hobbyists. The State&apos;s reputation as a source of gemstones and specimens for the collector and lapidary adds to the economy of the State by attracting tourists. Production of gemstones further adds to the State&apos;s economy through employment in the value added gemstone processing industries and by employment of Native American craftsmen.

Jan 1, 1988

By M. W. Harmer

Laboratory test work, pilot plant testing and plant experience with wet, fine mesh screens is discussed. High frequency, low amplitude, fine mesh, wet screens were installed on the 6th cleaner concentrate stream. These screens produce a 60% oversize recovery split of the molybdenite concentrate that is of leached equivalent quality. The undersize stream is leached with &apos;hot ferric chloride to remove Pb and Cu contaminates before roasting or shipment to sulfide customers. This plant modification is a good example of using existing technology in an unconventional flow sheet to yield significant cost savings.

Jan 1, 1990

By Franz Deix, Bernd Braun

A sensitive portion of Section U 6/3 of the Vienna, Austria subway system required construction of two single-track tunnels under a telecommunications facility, where strict ground settlement limitations had been set. Local geology, hydrology, and site constraints led to the decision to use the New Austrian Tunneling Method (NATM) supplemented by compressed air and partial dewatering. In addition, ground freezing was used, as the tunnel would pass through alluvial layers beneath the facility, with a cover of as little as 1.5 m. Laboratory testing and two in situ test fields were used to collect frozen soil data so that the freezing scheme ensured minimal heaving magnitude.

Jan 1, 1987

By Panagiotis Chryssanthakis

"The aim of this study is to give a better understanding for the performance of the composite material RRS and the synergy effect of its components under different stress regimes and while an excavation face advances during tunneling. The lower part of the Q-system scale (i.e. Q-values of 0.4 or less for a tunnel span of 10m) is commonly used for tunnel applications in softer rock formations. This is implied in the updated Q-chart, where the dimensioning of rock support by using Reinforced Ribs of Shotcrete (RRS) comprises the use of fiber reinforced shotcrete, S(fr), rock bolts and shotcreted beams reinforced with steel rebars. In this study, an effort has been made to simulate RRS in a numerical code and to study its behaviour in a real case study. A double tube, triple lane tunnel in weathered tuff has been chosen as reference material for testing RRS under changing load. A rather extensive parametric study has been run by using the same key input rock mass parameters and three different in situ stress regimes (sH/sv =2, sH/sv =1 and sH/sv =0.5). Changes have only been made to the RRS key input parameters in order to simulate the changing loads during the face excavation process in tunneling. The critical part of this numerical modelling work that is under investigation in this study under each stress regime, is the period just after the excavation: i.e 4 hours; 16 hours after excavation; and finally after the complete curing (28 days) of the cement based components. The RRS are installed in three consecutive numerical steps as follows: a) the application of S(fr) on the rock surface in order to even it up for the RRS application; b) radial bolting; and c) installation of the reinforcing steel rebars, that form the reinforced beam. The results are varying and are strongly dependent on the imposed stress regime and they show in general the following tendencies: The axial forces on S(fr) show that S(fr) is almost overloaded during the first 4 hours in all 3 stages. More particularly: For the case with sH/sv =2 a) the axial forces on S(fr) and on the steel rebars are reduced after 16 hours and 28 days; b) the same is observed on the shear stresses in S(fr) and on steel rebars, they are decreasing after 16 hours and 28 days; and c) the bolts loads are almost unchanged. For the case with sH/sv =1 a) the axial forces on the S(fr) are reduced after 16 hours and 28 days; b) the same is observed for the axial and shear stresses, as well as moments on the steel rebars, they are decreasing after 16 hours and 28 days; and c) the bolts loads are almost unchanged."

Jan 1, 2016

By Jerry W. Danni, R. Craig Ford, Kermit C. Benke, Jim B. Finley, Donald D. Runnells

Steady-state water balance models have historically been used in the management of acid drainage at mine sites. Such systems could be more realistically described by non-steady-state conditions. In addition, the evaluation of alternatives for closure and management of acid drainage must consider non-steady-state conditions. Dynamic systems modeling is a method for simulating water management systems, offering flexibility in: (1) simulating either steady-state or non-steady-state conditions, (2) allowing "what-if&apos; scenario testing. and (3) optimization of operation and closure alternatives. A case study is given for acidic drainage management during closure at a heap leach facility that demonstrates the utility of dynamic systems models.

Jan 1, 2000

By B. Slaker, M. M. Sears, G. Rashed

Ground falls represent a significant hazard at underground mines in the stone, sand and gravel (SSG) sector in the United States. Researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) are conducting detailed investigations into the complex loading conditions at underground stone mines operating in challenging conditions. This paper presents the application of numerical modeling to analyze pillar and roof stability at a dipping underground limestone mine.