Search Documents

By L. Sandbak

The TRJV Mine is located approximately 43 miles northeast of Winnemucca, along the east flank of the Osgood Mountains in the Potosi Mining District, Humboldt County, Northwest Nevada (see Figure 1). The Turquoise Ridge Mine is an underground mine, and is a 25% joint venture partner with Newmont Mining. The TRJV mine utilizes the underhand cut-and-fill mining method due to the relatively low rock quality in the ore zones and the relatively shallow dipping 25-45 degree ore body geometries. This paper defines a rehabilitation risk rating system (RRRS) for prioritizing rehabilitation of drifts damaged in the mining processes including long term development drifts providing access to the mining areas. The ultimate use is as a mine planning tool for the organized scheduling of rehab in a timely manner. A few case studies of the most needy rehab areas identified by the RRRS mapping system is presented, and the type of rehab completed design for these areas. Suggestions on improving the rehab risk mapping system include the use of support history and rock mass strength rating factors.

Feb 23, 2014

By E. Ilgar

Biodegradation of spodumene by Asnergillus niger has been investigated. This organism oxidizes sucrose to citric and oxalic acids (in approximately 50-sot proportions) which degrade the spodumene mineral. The kinetic effects of leach variables on the dissolution of lithium were determined. The maximum theoretically attainable rate of lithium extraction was calculated for the effect of pulp density, to be V : 3.01 x 10 kg m sand the corresponding constant value, K = 12.47% pulp density. The apparent activation energy of lithium extraction vas found to be ^E = 20.3 kJ and frequency factor A = 5.66 x 10 s for S-spodumene leaching by synthetic -3 citric and oxalic acids (each in 0.05 kmol m-3 concentrations).

Jan 1, 1989

By S. D. Rosenthal

"This article will share my ‘shift in career direction’ journey from corporate mine engineer, with 31 years of mining various commodities with a wide range of responsibilities in a variety of countries, to the world of academia. There are times in one’s career that a change is required, albeit perhaps not as drastic of a change as moving to teaching. This paper will share how the transition arose, the decision to make the change, the challenges of the first year in academia and the journey within academia going into the second year.As a graduate of the Montana College of Mineral Science and Technology (Montana Tech) with a B.S. mining engineering degree in May of 1982, my first job with Utah International in the Farmington, NM area took me back to my home state of New Mexico. Some of you will remember that the early 1980s was not a period of prolific opportunities for mining engineers, given low commodity prices, especially for copper (for example, Anaconda Co. had been taken over by Arco and was in the midst of closing down its Butte operations). Coal was good and the learning opportunities abounded with Utah (which became BHP and then BHP Billiton).Gold was taking off in the mid to late 1980s thanks to use of cyanide and heap leaching technology improvements, coupled with deregulation of the gold price, so I ventured off to work in the gold industry with a (then) junior Canadian company called Barrick at a new acquisition of theirs known as Goldstrike. That same gold surge was causing a shortage of iron ore mining engineers in Australia. So after a few years in Nevada, I uprooted the family and left for a little town in the Pilbara of West Australia, known as Newman, to work in the iron ore industry with BHP Iron Ore. An initial short overseas posting turned into six plus years before transferring to BHP’s Indonesian steam coal mines in Kalimantan on the island of Borneo. BHP was going through a rough period following some ill-fated projects (Magma Copper purchase, Beanup and HBI) and was reviewing assets and staffing, so internal opportunities became scarce. Employees were encouraged to “leave the company and find work elsewhere.” So, off I went to Argentina to try copper mining in the Andes with Minera Alumbrera. This short stint in South America was followed by a move to another mining town, Morenci, AZ, and a posting with Phelps Dodge (now Freeport- McMoRan). After 12-plus years without living close to snow, we moved to the Denver, CO area in a new position with Newmont Mining Corp. Along the way I became a professional engineer (Nevada) and completed a masters in project engineering and management. After 11 years with Newmont, I moved to Butte, MT where I accepted a position as assistant professor of mining engineering."

Jan 1, 2015

By Neal P. Cochran

It is always a pleasure for me to address a group of mining engineers. I am doubly grateful when I am allotted sufficient time to describe the total Office of Coal Research program. My remarks are directed to our total program but I trust you will all understand my emphasis of the utilization aspect of our activities since that is my portion of the program. From its inception, the Office of Coal Research has sought out creative ideas for improving our national use of coal by developing new uses, improved mining procedures, lower costs, and appropriate studies with respect to the resource itself. Quite early in the game, our Economics and Marketing Division contracted for studies with respect to New England export market, Western coal, and similar items. Our Mining and Preparation Division has successfully developed a packaged coal-fired boiler and has partially developed a packaged fluid-bed type boiler as well. Our Mining and Preparation Division is working in such diverse fields as treatment of sewage with coal and the separation of coal into distinct-petrographic constituents so that all fractions of the coal can be put to the best possible use. We would like to be doing more work on improved mining methods, better preparation techniques, and any other mining improvement that will benefit the industry and our program. The synthetic fuel plants I will describe later will operate seven days per week, 24 hours per day. We would like the mine to operate on this same sort of cycle and are prepared to support research that will lead to this.

Jan 1, 1970

By Perry M. Jones

An important operational and environ-mental concern associated with in situ leaching activity is the balance between solution injection and recovery. Solution balance is an important indicator of the capability of a particular in situ hydrologic design to efficiently and effectively control and distribute leach solution within the target ore zone. The Bureau of Mines is investigating the factors that affect solution balance in an unsaturated ore deposit, as part of ongoing in situ leaching hydrologic investigations at the Cyprus Casa Grande Mine. Flow conditions in 58 injection and recovery wells at the Casa Grande In Situ Leaching Test Facility were monitored daily over an 18 month period. Changes in the balance between injection and recovery occurring during this period were evaluated using analytical and statistical methods. The results permit estimation of solution distribution and the volume of solution stored in microfractures and interstitial pore spaces within the deposit following 18 months of leaching. Approximately half of the difference between well injection and well recovery can be accounted for by solution movement through macrofractures into nearby drifts. Estimates of solution storage within the ore deposit at the end of 18 months of leaching range from 3.5 to 6.9 pet. of injected solution. These results also suggest that 13 to 26 pet. of the fracture/interstitial pore space in the deposit was saturated with solution after 18 months of leaching.

Jan 1, 1991

By D. Bessinger, J. M. A. Geldenhuis

High titania slag is produced from the smelting of ilmenite. These slags contain approximately 85 per cent TiO2 and consist mainly of a M3O5 solid-solution phase. During cooling the slag can decrepitate to a fine particulate material, which decreases the value of the product. Based on X-ray diffraction analyses of the decrepitated slag after cooling, it was found that the M3O5 phase had almost disappeared. The disappearance of the M3O5 phase was linked to oxidation of the slag. A M6O11 phase formed in the decrepitated slag. It is postulated that decrepitation of high titania slag is caused by volume changes due to the oxidation of the M3O5 phase in the slag.

Jan 1, 2005

By Charles W. Axten

Since the mid-1970s, samples of airborne and waterborne fibrous particulates have been collected in the area of the Northshore Taconite Ore Processing Facility by the Minnesota Department of Health (MDH), the Minnesota Pollution Control Agency (PCA), and the University of Minnesota. Indirect sample preparation has consistently been used although other aspects of the sampling methods and sites have varied and analytical procedures were altered over time as more accurate and precise microscopy methods were developed (i.e., phase contrast optical microscopy, transmission electron microscopy, transmission electron microscopy with energy dispersive spectroscopy). In the mid-1970s, levels of airborne fibrous particulate in the Silver Bay area averaged from 0.00030 to 0.03 f/ml. This level was significantly greater than levels of similar particulates in the St. Paul, MN area, although two of the Silver Bay sampling sites, considered individually, did not indicate levels of fibrous particulate markedly different than that seen in St. Paul. More recent sampling data (i.e., 1990?2001) indicate mean concentration of airborne fibrous particulates (amphibole-like fibrous particulates) of 0.0020 f/ml with a range of values from 0.0001 to 0.0140 f/ml. Such levels are not significantly different from those seen in other non-urban environments in the US and Europe. Concentrations of fibrous particulates in water samples were higher in the mid-1970 when iron ore tailings were being deposited in Lake Superior, but since the tailings have been deposited on land waterborne levels of fibrous particulate in the Beaver River have remained relatively constant averaging in the range of 7.5 MFL. This level is only slightly in excess of the current EPA drinking water standard for fibrous particulates. Review and consideration of this data is important in determining the potential health risks associated with airborne and waterborne fibrous particulates in the areas of the Northshore Taconite Ore Processing Facility. © 2007 Elsevier Inc. All rights reserved. Keywords: Taconite; Asbestos; Asbestiform fibers; Fibrous particulates; Cleavage fragments; Phase contrast optical microscopy; Transmission electron microscopy

Jan 1, 2007

By Neall. George M.

No method of roof control yet devised has proven to be universally acceptable for the wide range of strata conditions experienced in U.S. coal mines. However, a relatively new innovation, the roof truss, has proven itself capable of preventing roof failures which both conventional and resin bolting could not. Presently, the economics of roof trusses are not favorable when compared to bolting due primarily to drilling and installation procedures, but this is expected to change with improved truss and equipment designs. To realize the full potential of this new method of roof control, design criteria are needed which can optimize the effect of the truss for varying strata conditions. A review of the literature reveals that some work has been conducted on the roof truss. 1 Gambrell and Haynes (1970) showed that the roof truss is superior to angled roofbolts installed through a header. Sheorey, Verma, and singh2 (1973) used statics to prove that the optimum angle of inclination should be greater than 450? However, to date, no systematic attempt has been made to establish design criteria. In this report, the problem was approached in three ways. First, model studies were performed to determine general trends of truss support as a function of a number of variables. This provided a better understanding of the support mechanism involved. Secondly, beam theory was employed to calculate the actual support capacity of a truss, realizing the many simplifications, assumptions, and shortcomings of this approach to such a complicated problem. Last, field testing will be utilized to test the hypotheses previously developed and provide hard data to further synthesize roof truss design criteria. Field testing has recently commenced and should be complete before mid 1977.

Jan 1, 1977

By Dr. Peter J. Conroy

The current study is part of the U.S. Department of Energy's (DOE) on-going subsidence research program. The long-term objective of the DOE program is to develop analytical methods of subsidence prediction applicable over a broad range of geologic and mining conditions encountered in the United States. The DOE currently has several contracts in progress to develop a sound data base that can be used in the development of predictive models. Dames & Moore is currently under contract to the DOE to collect and analyze detailed subsidence and hydrologic data from a coal mine employing longwall mining methods in the Eastern Coal Province. Work under Contract No. DE-AC22-80PC 30335 began in October of 1980 and will continue through September of 1984. This paper summarizes the work that has been completed through September of 1981 and presents the results that have been achieved during this period. Technical difficulties encountered during both the installation and monitoring phases are discussed, and recommendations for future work are presented.

Jan 1, 1982

By James Thompson

Mine planning at Consolidation Coal Company's (Consol) Glenharold Mine in North Dakota is being constrained by environ¬mental concerns that did not exist when the mine opened in 1965. One such concern which developed in the mid-1970's is the impact of mining on woodlands that are considered impor¬tant wildlife habitat. To better coordinate mine planning with permitting, a cooperative task force was created to evaluate woodlands for their wild¬life habitat potential. The task force included representatives from Consol and state and federal agencies. This cooperative process is seen as a method of communication between industry and government and as a way of developing decision-making tools for mine planners and regulatory agencies.

Jan 1, 1981

By J. Bilant, B. Carlson, N. Gow

High Pressure Grinding Roll (HPGR) technology has been evaluated to replace tertiary cone crushing at Coeur Rochester operations (Coeur Rochester, Inc.) as an opportunity to improve silver recovery. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact of metallurgical recovery and heap leach performance of crushed product generated by an HPGR. In 2018, Forte Dynamics evaluated the HPGR laboratory metallurgical data from Coeur Rochester and all third parties to develop field-scale leach curves based on new crushing scenarios. The laboratory recovery test work data was consolidated and scaled to field conditions to determine projected heap leach performance. Based on the metallurgical testing conducted, the replacement of current tertiary cone crushers with HPGR technology has the potential to increase Coeur Rochester’s silver recovery rate by 8%, from 61% to 69%, and shorten the overall timing of silver recoveries from 20 years to just over two years. INTRODUCTION The Rochester mine, and associated valley fill heap leach facilities is an open-pit silver and gold mine located in Pershing County, Nevada, approximately 26 miles northeast of the city of Lovelock. In 2017, Rochester produced approximately 4.7M troy oz silver (Ag) and 51k troy oz gold (Au). Ore mined at Rochester is either fed directly to the primary X-Pit crusher, crushed at an in-pit crusher system, or placed directly onto a heap leach pad as run-of-mine (ROM). Both crushing circuits are comprised of three stages of crushing to produce a nominal 3/8” ore. Primary crushing consists of jaw crushing while secondary and tertiary crushing are composed of varying cone crushers. Historical recovery rates of crushed Rochester ore average 61.4% Ag and 95.9% Au over a period of 20 years [1]. These rates were derived from third party verification of in-house metallurgical test results, crusher production and heap leach production results from 1986 through 2004 in a private report for Rochester produced by KD Engineering Co., Inc. Recovery rates are regularly verified by compositing daily samples of ore delivered to each leach pad from the X-pit crusher, in-pit crusher, and/or ROM. A proportionate split of each sample is used to generate monthly composites for metallurgical analysis utilizing column leaching and bottle roll leaching. These tests are run in a manner analogous with production conditions and deliver test results that provide expected heap leach performance. As the Rochester oxide deposit has been mineralogically and metallurgically consistent, the gold and silver recovery trends have also been consistent over the life of the project. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact of HPGR technology to metallurgical recovery and heap leach performance of crushed product in an open circuit configuration, as a potential replacement for the currently in place tertiary cone crushers. During these years, HPGR was evaluated in three phases of test work.

Jan 1, 2019

By Jonathan M. Pachter

The Bailey mining complex is located in Greene County, PA in the valley of Talley Run, a small stream tributary to the Enlow Fork of Wheeling Creek as shown on the location map insert found on Figure 1. The Bailey complex includes two Pittsburgh No. 8 Seam deep mines (Bailey and Bailey #2), a coal preparation plant, and two refuse areas (for disposal of coarse and fine processing waste). Clean coal is shipped from the complex via a 24.15 km (15 mile) rail spur, which connects to the Monongahela Railroad in Waynesburg, PA. In early 1981, Consolidation Coal Company (Consol) began a permitting effort aimed at beginning construction of Bailey, the largest underground coal mining complex to be built to date in the United States. Construction of the Bailey Mine began in December, 1981, less than six (6) months following the first application submittal. Clean coal was produced by the Bailey Preparation Plant in September, 1984. Effective project planning, including early formulation of a project planning team, identification of "red flag" issues, innovative responses to environmental questions and development of environmentally sound project designs, all contributed to the relatively quick permitting at Bailey.

Jan 1, 1985

By A. Moergeli

The Swiss are currently building the world’s longest tunnel, the 35-mile long Gotthard Base Tunnel. At Sedrun, for the first time in tunneling, four Roadway Support Machines will drive through most difficult ground, supporting variable diameters of up to 13 m. The machines are prepared for their first deployment. At Amsteg, two Hard Rock TBMs have successfully crossed a known fault zone by applying full circle steel arches and shotcrete immediately behind the cutter head. Comparisons between Drill& Blast and Hard Rock TBM are shown.

Jan 1, 2005

By Wade W. Bristol

The Jerritt Canyon Joint Venture project is located about 80 km (50 miles) north of Elko, NV. It produces approximately 9.3 t/a (300,000 oz/year) of gold. The joint venture is 70% owned by Independence Mining and 30% by Meridian Gold. Independence Mining is the operator. The Jerritt Canyon Joint Venture started operations in 1980 by mining a series of open-pit mines. The discovery of deeper ores during early 1990s made it neccessary for the operation to mine a large portion of its annual production by underground mining methods. Underground production started in 1993 at the West Generator Mine. This was followed by the Murray Mine in late 1994. Two additional underground projects are being developed. Underground mining at Jerritt Canyon is scheduled to produce about 3.9 t (128,000 oz) in 1997.

Jan 1, 1997

By Katarína Gáborová, Marcela Achimovičová, María Florencia Márquez‑Zavalía, Jaroslav Briančin, Oľga Šestinová, Pavel Škácha

In this paper, the structure, morphology, chemical composition and leaching of naumannite ( Ag2Se) were studied. Mechanical activation of Ag2Se in a planetary ball mill resulted in increasing its specific surface area. The influence of milling time on the particle size was studied by particle size distribution analysis and scanning electron microscopy. The leaching kinetics of non-activated and mechanically activated samples in 3.5–7.9 mol/L HNO3 solutions were examined. Subsequently, the effect of leaching temperature in the range of 25–50°C on the recovery of silver from mechanically activated naumannite was documented. The maximum yield of silver 94% was achieved after 120 min of leaching in 7.9 mol/L HNO3 at 50°C for the sample mechanically activated for 30 min. Based on calculated activation energy values from the Arrhenius equation, a mixed leaching mechanism consisting of diffusion and surface chemical reaction as the rate-controlling steps of the solidliquid reaction was assessed.

Mar 4, 2023

By S. M. Moore, J. F. Burr, R. Fernando, D. Snyder

"The Mine Improvement and New Emergency Response Act of 2006 (MINER Act Public Law 109-236) was passed by Congress in response to three major underground coal mine accidents in the United States that claimed the lives of 19 miners. The Act resulted in substantial changes in the underground coal industry relative to the use of technology for mine escape, rescue, disaster response and other areas where the lack of these technologies contributed to the fatalities caused by these tragedies. This year marks the 10th anniversary of the MINER Act, which makes it an opportune time to reflect on the events that led to its passage, the changes that have been made since then, and the work that remains to be done. As discussed below, the last decade has demonstrated tremendous cooperative efforts among mining operators, technology innovators, labor, The National Institute for Occupational Safety and Health (NIOSH), the U.S. Mine Safety and Health Administration (MSHA) and state regulators, resulting in substantial improvement of the technologies used for escape and rescue and noteworthy progress toward meeting many of the goals of the MINER Act. While the MINER Act and this article pertain primarily to coal mining, many of the technologies are equally applicable to any underground mining and have already found some acceptance outside of coal. TECHNOLOGY GAPS TARGETED BY THE MINER ACT The MINER Act addressed several technology challenges: • Problems with donning and switching between self-contained self-rescuers (SCSRs). • Poor visibility in smoke. • No wayfinding assistance for escape from the mine. • Limited breathable air supply. • Inability to locate trapped miners. • Inability to communicate with trapped miners. • Failure of mine seals. The MINER Act had several provisions that prescribed specific safety technologies intended to address these issues. Many of these were directed at post-accident technology requirements — an area in which Congress mandated additional technology investment. Specifically, the Act required mine operators to submit emergency response plans (ERPs) that contained provisions for implementing new or improved post-accident communications, tracking, lifelines, refuge alternatives and breathable air supplies along with training for emergency procedures and local coordination of emergency response. Most of the requirements were to be carried out within three years of the ratification of the MINER Act. In addition to these requirements for mine operators, the Act clarified and expanded NIOSH’s role and authority in enhancing the development of new mine safety technologies and expediting their commercial availability. The MINER Act also required NIOSH to develop research on refuge chambers, mine seals and the use of belt air and fire-retardant belts. Mine seals had to be upgraded and MSHA turned to NIOSH for applied research to establish the new explosion-resistance requirements. Progress toward closing the gaps."

Jan 1, 2017

By Rafael Moure

On April 21, 1980 the Oil, Chemical and Atomic Workers Union (OCAW) submitted a petition urging the revision of the Mine Safety and Health Administration (MSHA) permissible exposure limit to radon daughters in underground mines. This petition asks for: 1. Annual worker exposure to be lowered from the current 4 WLM/year to 0.7 WLM/year; 2. Full economic protection for workers whose exposure exceeds the proposed 0.7 WLM/ year; and 3. The primary means of lowering workers' radiation exposures shall be environmental controls. I will present the scientific rationale for the lower standard requested in our petition to the Department of Labor. [1. Radiation Exposures to Uranium Miners] Two types of radiation exposures are present in the environment of uranium mines: A. [External Exposure] to gamma sources which until 1978 was considered as negligible compared with internal alpha radiation. R. E. Utting (1), in an investigation of three Canadian uranium mines, found levels of exposures adding to an annual dose equivalent of 3 rems (30 mSv)/year. He concluded that gamma dosages may be a major fraction of the maximum permissible dose for many individual miners. The U.S. experience has shown that there is significant gamma exposure in U.S. uranium mines and, therefore, it could contribute to the total radiation exposure to the lungs in combination with internal alpha radiation. Before ventilation improvements in uranium mines, the contribution of external radiation to total lung dosage was relatively small. After improvements in ventilation, the reduction in internal radiation exposure appears to be in 1980 as low as 1/10 of the 1950 dosages. However, ventilation improvements do not affect external gamma radiation. Gamma radiation remains at the same 1950's level, and it represents today a higher proportion of the total radiation burden to the miner's lungs. MSHA regulations (57.5-47) state that if gamma exposure is below 2.0 milliroentgens per hour, then workers are not required to wear gamma dosimeters and cummulative gamma radiation records need not be kept. Assuming an exposure of 1.9 milliroentgens per hour per 173 hours/month for 12 months,a miner would accumulate a dose from external radiation of 3.9 rems/ year. This dosage would, of course, go unrecorded. MSHA, therefore, should consider a downward revision of the external radiation permissible exposure limit of 2.0 milliroentgens/hour. MSHA should make clear that this exposure level, when added to the internal exposure, does not make for sound health physics -even though the measured current levels do not approach 2.0 milliroentgens/hour. B. [Internal Exposure] to alpha radiation is still the larger contributor to lung irradiation in uranium miners. The target organ is still the lung. The parameters to be considered in determining the biological radiation load appear in Table I for radon daughters present in the upper respiratory tract (URT). TABLE I RADIATION DOSE PARAMETERS IN THE URT OF URANIUM MINERS Parameter Uranium Underground Mining [1. Quantity of the Absorbed Radon daughters (Po-218, Nuclide Pb-214, Bi-214) deposit in bronchial and lung tissue. (Measured by air concentration, Working Levels) 2. Type of Radiation Emitted Alpha Particles 3. Energy of Radiation High-Linear Energy Transfer 4. Half-life of the Nuclide Ra 222, 3.8 days in the Organ Po-218 (RaA), T1/2 = 3.1 minutes Pb-214 (RaB), T1/2 = 26.8 minutes Bi-264 (RaC), Vi = 19.7 minutes 5. Selection Factor of the Direct inhalation with mine Organ dust to be deposited in the tipper Respiratory Tract 6. Mass and Form of the Organ Especially cancer sensitive, tracheobronchial region and bronchi* 7. Distribution of the Activity Dependent on deposited dust in the Organ distribution in the Upper Respiratory Tract 8. Chemical Nature of All compounds (RaA, RaB, RaC) Incorporated Substance biologically insoluble. (Only localized, irradiation) *See Reference (2)] The parameters of Table I depend, in turn, on the demography of the exposed population, especially: 1. Age 2. Sex 3. Health Status 4. Genetic Constitution 5. Lifestyle (Smoking, Diet) Some of these demographic characteristics of uran-

Jan 1, 1981

By Larry F. Drolet

Charleston, SC is anything but boring. The city was founded in 1670 and has played a significant role throughout the history of the United States. Located along the coast of the Atlantic Ocean in the southeastern United States, Charleston was a vital city in America?s early existence. Charleston?s coastal location has helped the city become the fourth largest cargo port in the United States and earn the 2011 designation as the number one travel destination in the United States by the Conde Nast Traveler Magazine. Part of Charleston?s charm and beauty can be attributed to its historic structures and churches that line nearly every sidewalk, roadways that were laid out based on the width of horse carriages, great weather, southern hospitality and coastal living. Now imagine the challenges of installing new, or re-placing aging infrastructure, in this setting. Every shovel full of dirt, every stick of pipe and every roadway sub-surface has its own historic story to tell. For engineering minded individuals, Charleston?s infrastructure has almost as fascinating a history as its more visible surface structures. Charleston was among one of the first American cities to construct separate sanitary and storm water drainage infrastructure. This concept has roots dating back to the city?s founding and is a credit to the foresight of its founding fathers who understood the basic health differences between sanitary and storm water.

Jan 1, 2013

By J. O. Down

St. Marys Cement Company operates two cement plants in Southern Ontario, Canada. The original plant, located at St. Marys, a town 20 miles north of London, Ontario, began operations in 1912. A second plant, located at Bowmanville, Ontario, 40 miles north east of Toronto, began operations in 1967. In June 1973, St. Marys Cement began feasibility studies of modernizing their wet process plant at St. Marys. Over its 61 year life, this plant had been expanded from 335 m. tons per day (375 s. tons per day) to 2000 tpd (2200 s. tons per day), with all the original equipment retired several years ago. The objectives of the feasibility study were to develop a conceptual plan for a dry process plant and to de-, fine the appropriate process method and equipment. This study proceded along four fundamental fronts: a) How could the clay raw material, a glacial till with up to 20% boulder content, be processed in dry form and beneficiated? b) Were the raw materials suitable for the most efficient form of dry process kiln, the 4-stage preheater? If a 4-stage preheater kiln is selected should it utilize a precalciner? c) What type of clinker cooler should be used? d) What environmental constraints would be imposed on this plant and how can they be reconciled with capital and operating limitations? During the feasibility stage, pilot plant work was done on two possible solutions to the clay problem, operating plants in Europe were visited and discussions held with kiln and mill vendors.

Jan 1, 1977

By Shosei Ph. D Serata

The Stress Control Method of mine design provides enhanced engineering control over the behavior of underground structures in comparison to conventional mine design methods. The same Method can be applied to achieve design control of surface subsidence. The basic mechanism relating undergroued deformation and surface subsidence is disclosed by mine simulations, using the REM (Rheological Element Method) computer code, whose predictions have been validated by field measurements. The key components of the underlying mechanism of surface subsidence have been shown to be the stress envelopes formed in the process of underground excavation. It has also been demonstrated that significant control of surface subsidence can be achieved by designing the geometry and timing of underground excavation to regulate the formation of stress envelopes. A field example is given in this paper to illustrate this application of the Stress Control Method.

Jan 1, 1986