Search Documents

By R. C. Bunge

Many minerals float best with fatty acids in the intermediate pH range. For example, fluorite, a semi soluble salt mineral, exhibits a maximum contact angle and a maximum flotation recovery in the pH range of 6-8 after conditioning in a palmitate solution (fig. 1). The maximum in flotation coincides roughly, as many researchers have observed, with the boundary of bulk precipitation of the fatty acid. According to fig. Z this boundary is in the above case of 5xl0-7 M palmitate approximately at pH 6.3. For assessing the phenomena occurring at the bulk precipitation boundary of fatty acids, the surface tensions of carboxylate solutions have been measured under various conditions. Fig. 3 shows the surface tension development of palmitate and myristate solutions of increasing concentration at pH 12. Also shown are the bulk precipitation edges (BPE) of the respective solid species that is stable under these conditions, that is the potassium acid soap, HKAZ. Both curves display a similar behavior. As the concentration of carboxylat,e increases, the surface tension decreases, until a minimum is reached at which the curves level off. The decrease of surface tension with increasing carboxylate concentration is generally taken to indicate the surface excess of the carboxylate ion. The point where the curve suddenly levels off has not yet been explained. While it is well known that the onset of micellization (CMC) may cause such an inflexion of the surface tension curve, this cannot be the case here because the position of this point depends, as shown in fig. 4 for palmitate, on pH (the CMC is generally independent of pH). We believe that this point indicates the precipitation of a colloidal acid soap (colloidal precipitation edge, CPE) before the bulk precipitation of this species sets in (BPE).

Jan 1, 1994

By M. Rossi

The use of service variables in geostatistics (grade-thickness) is common in industry when developing block grade models and geologic resource estimates. This is particularly true in the case of sedimentary and strata-bound-type deposits. The approach has proven merits when assessing ore reserves. However, there are cases where its application for preliminary data analysis produces biased estimates. One such case is encountered in uranium disequilibrium studies. This paper demonstrates the inadequacy of service variables when performing uranium disequilibrium studies. Disequilibrium analysis is a necessary pre-processing step when radiation counts are used as raw data to calculate uranium reserves. Typically, a probe is used to obtain the gamma counts from open drill holes. These counts are then regressed (and corrected) against chemical assays obtained from core samples. During this process, the grade-thickness variable produces an optimistic image of the relationship between probe grades and chemical (true) grades, causing overestimation of the final geologic resource. The problem is analyzed through a case study.

Jan 1, 1991

By Jeffrey L. Zelms

There is no known, practical substitute for lead in the automobiles, communications systems, medical equipment and computers that Americans use every day. However, there are many who say lead should be stopped at its source -- banned. As America's largest lead producer, The Doe Run Company has ralized that it must do more than mine and reclaim lead efficiently and safely. It must also earn the public's consent to operate if it is to continue to be a viable business. LEAD - THE BRILLIANT PERFORMER: REFURBISHING AN IMAGE It's been an embarrassingly long time since I was a college student. However, I remember there was no course at the University of Missouri's School of Mines and Metallurgy that had anything to do with the public relations aspects of mining or, put another way, the politicization of mining. It's been an embarrassingly long time since I was a college student. However, I remember there was no course at the University of Missouri's School of Mines and Metallurgy that had anything to do with the public relations aspects of mining or, put another way, the politicization of mining. I haven’t perused the course catalog for Penn State’s College of Earth and Minerals Sciences. But I strongly suspect I wouldn’t find such a course there today, either. A statement by the chairman of one of the country’s largest chemical companies leads to the point I want to make. He described his business this way. He said, “We’re a public affairs company that just happens to produce and market chemicals.” Like chemicals, minerals and mining are politicized today. To the extent that we don’t understand that reality, we don’t understand that reality – and act on it – we’re less likely to survive in this business. Some of you may well be saying to yourselves, “This guy Zelms is an alarmist.” That’s fair enough. Because it is absolutely true that there’s n o known, practical substitute for lead today. And it’s also absolutely true that, knowingly or not, Americans use lead everyday. It’s in our automobile batteries. It’s an integral part of communications systems. High tech (and low tech) medical equipment contains lead. And lead is an essential component of computer and TV screens. But even with all these uses, lead has a negative image today. An image so negative that its very existence is threatened. If you doubt that, consider these two statements made in 1989. Statement one. “It is probably reasonable to argue that exposure is the single most important and critical environmental health problem in the U.S., and possibly also the world…” Statement number two. “Many of the uses of lead should be terminated. We need to go back to the ultimate source: that is, taking lead out of the ground and putting it into the product stream and we need to turn it off at the ultimate source. Not the approximate lead in gasoline, or lead in air, or lead in food. Go right back to the source and start cranking it down." (End quote.) Those are what I call strong statements. And they weren’t made by some celebrity spokesperson for the environment like Meryl Streep. Both these statements were made by Dr. Ellen Silbergeld, whose long list of professional and academic credentials includes: o Adjunct professor and research scientist at the University of Maryland Medical School and Johns Hopkins: o Chief toxic scientist and director of the Toxic Chemicals Program of the Environmental Defense fund; o and President of the Society for Occupational and Environmental Health. If Dr. Silbergeld were the only person making these kinds of statements, it would be one thing. But she’s not a voice in the wilderness, by any means. Also for those of you who say, well since there’s no known substitute for lead, how on earth could it be banned. I refer you to a number of bills before Congress that would permit the EPA to ban any product if it is determined that its

Jan 1, 1992

By E. W. Geist, W. J. Bronkala

PRINCIPLES OF MAGNETIC SEPARATION The application of magnetic separators relies on the different behavior of individual mineral particles under the influence of magnetic forces. When exposed to a magnetic field, all materials are affected in some way. According to whether materials are attracted or repelled by the magnetic field, they are designated paramagnetic or diamagnetic, respectively. Paramagnetic materials are attracted along lines of magnetic force from points of lower magnetic field intensity to points of higher magnetic field intensity. The very strong response of some materials to a magnetic field is sometimes designated ferromagnetic and the particles attracted frequently retain magnetic properties after the applied magnetic field is removed. Diamagnetic materials are repelled along the lines of magnetic force from points of high magnetic intensity to points of lower field intensity. Only limited commercial use of diamagnetic effects has been made. For practical applications, the paramagnetic groupings are: 1. Strongly magnetic (ferromagnetic) 2. Magnetic 3. Weakly Magnetic 4. Non-magnetic The limits of these groupings are not well defined and will vary in some mineral species. Only a few minerals are ferromagnetic (magnetite is an example) and arbitrarily some investigators have selected 10,000 gauss, or 1 Telsa, as the dividing line between low and high intensity magnetic fields. I. S. Wells has developed a table indicating the magnetic intensity required to separate a selected grouping of minerals which is shown in Table 1 on page 2. A similar table has been developed by Carpco Inc. of Jacksonville, Florida in conjunction with the use of its high tension separators. This table, Table 2 on page 3 shows other minerals grouped in the broader categories cited above. Magnetic separation methods are used either to separate valuable minerals from nonmagnetic waste or magnetic impurities or other valuable magnetic minerals from bulk nonmagnetic values. Magnetically susceptible mineral particles occur as either individually discrete particles,

Jan 1, 1986

By J. DuCarme, A. Smith, M. Reyes

"A magnetic proximity detection system is mounted on a mobile mining machine to prevent underground workers from being pinned or struck by machine motion. The system generates magnetic fields around the machine to determine safe working distances. The minerworn component measures the magnetic field in order to approximate location. Large masses of steel, such as those from mining equipment, can alter the magnetic field distribution. This affects the locational accuracy of the system, thus adversely impacting worker safety. To examine this problem, U.S. National Institute for Occupational Safety and Health researchers developed a method and test system to study the influence of a steel mass on the magnetic field distribution. The results show that a steel plate can strengthen the magnetic field perpendicular to the generator by up to 40 percent. Furthermore, they show that the degree of the influence on the field distribution is a function of distance. The results from this study can be used to further develop and improve the performance and reliability of electromagnetic proximity detection systems used in underground mining applications.IntroductionOn average, 250 miners are injured every year, and 43 miners were reported to be killed by striking or pinning accidents involving continuous mining machines in the United States between 1984 and 2015, according to the U.S. Mine Safety and Health Administration (MSHA, 2015). Continuous mining machines are large mobile machines used to mechanically cut coal in underground mines. These machines weigh approximately 60 t (132,000 lb) each. Although modern continuous mining machines can be remotely controlled, operators still need to be close to the machine primarily because of the low visibility and wide blind spots of the underground working environment.The MSHA promulgated a final regulation in 2015 that requires the use of proximity detection systems on all continuous mining machines except fullface machines. MSHA has approved five such systems to be intrinsically safe for use in underground coal mines: (1) Strata Worldwide’s HazardAvert System, (2) Frederick Mining’s Model 200 HazardAvert Detection System, (3) Nautilus International’s Coal-Buddy System, (4) Matrix Design Group’s M3- 1000/Joy Global SmartZone Gen 1 and (5) Matrix Design Group’s IntelliZone/ Joy Global SmartZone Gen 2."

Jan 6, 2018

By D. P. Plute

The mechanization of the materials management function must contribute to the overall goal of optimization of profits. A computerized system contributes to the profitability of the company by saving more than it costs to operate. Design and implementation of the sys- tem must respond to the needs of users, the operating environment of the property, and must support the objectives of materials management. Three basic functions interact within the scope of materials management. They are inventory control, purchasing, and warehousing which have the following objectives: 1) Inventory control-to request materials in a timely manner and in quantities that provide the best level of support to users at the lowest cost. 2) Purchasing-to purchase requested materials and services at the required time and at the lowest cost. 3) Warehousing-to efficiently receive, store, and issue materials and to prepare accurate transaction documents for the activities. The development of the mechanized materials management system will require a plan and objective analysis by management and system users of system requirements. A typical plan would include: 1) System Design Objectives-the development of objectives that support mechanization of the materials management function. 2) System Characteristics and Concepts- the development of key system concepts and characteristics, which identify the needs of materials management. 3) System Inventory Item Classification- development and assignment of inventory category codes to inventory items. 4) System Order Decision Rules-the development of decision rules and forecasting techniques to minimize the inventory investment and to provide acceptable support levels. 5) System Report Structure-the development of a report structure to support the goals and objectives of materials management. 6) System Report Design-the development and design of reports for effective utilization of the mechanized system.

Jan 1, 1979

Careful financial analysis of capital investments has always been a vital task in mining which is one of the most capital intensive sectors of the economy. Furthermore, mining costs have leapt ahead at an astonishing rate in recent years not just due to accelerated inflation, which affects everyone, but also due to the imposition of enormous costs of enviromental regulation and the continuing decline in ore tenor. Not only have unit costs risen, but the amount of effort expended to recover a pound of metal has increased due to the inexorable decrease in ore grades. New low-margin, high-volume mining investments place increasing importance on sound financial planning. Owing to the enormous investments involved, a greater share of individual corporate resources is committed to these projects than is normally the case in other industries. Thus, the consequences of failure are extremely grave, and a close examination of all inputs to the evaluation equation is clearly indicated.

Jan 1, 1979

By Wenhua Wan, Jan M. Mutmansky

Many concerns have been expressed worldwide regarding the use of diesel equipment in underground mines due to the potential health risks associated with diesel particulate matter (DPM). In assessing the risk to the health of miners and designing control strategies for DPM, it is important to know the concentration of DPM in the working areas of a mine. In some mines, significant stratification occurs due to the characteristics of the diesel exhaust, affecting exposure and the ability to measure DPM concentrations accurately. This study outlines some of the concentration profile data obtained during sampling at three mines where diesels were employed. Mine #1 (a gold mine) employed large openings in which a diesel-powered roof bolter was used. Mines #2 and #3 are both room-and-pillar operations with varying conditions. Mine #2 is an experimental mine where two stationary diesels were utilized for sampling purposes, while Mine #3 is a traditional evaporite operation using two mobile diesel vehicles for section haulage. These field studies indicated that some level of stratification occurred in all the mines, but the stratification was not as pronounced in the case of Mine #2 due to the complex pattern of exhaust emissions generated by the vehicles. The stratification seemed to depend on the distance from the vehicle, the mine air velocity, whether the vehicles were moving or stationary, and whether the exhaust was diluted by equipment design features. The concentration of DPM was generally higher at samplers located near the roof and lower at samplers located near the floor. However, this was not found in all cases. This paper provides conclusions on how knowledge of stratification patterns can be utilized in sampling and control of DPM in mine atmospheres.

Jan 1, 1997

NIOSH is conducting research to reduce the silica dust exposure of workers at surface coal mines. One goal of this research is to evaluate the relationship between drilling parameters, rock strata and silica dust generation. This study involved measuring blast hole emission dust from a rotary drill rig which required sampling high concentration dust (>400 mg/m3) for silica content in a high velocity airstream. To measure dust initially, traditional sampling methods using personal sampling instruments were attempted in and around the shroud area of the drill with no success. Variations in the dust cloud concentrations under the shroud, the condition of the shroud and its orientation over the hole, and ambient air conditions prevented consistent and accurate dust measurements from being obtained. Amore consistent dust cloud is necessary for accurate measurements. An area of the drill’s dust collector system that consistently draws the emitted airborne dust from the hole is the collector tube. This tube connects the drill collector’s vacuum and dust filtration system to the shroud area. Assuming the collector system is working as designed, sampling from the collector tube would enable more consistent and accurate samples to be taken. However, current personal samplers are unable to sample in the concentrations and velocities experienced in the collector tube, so another method had to be devised. To achieve the desired results, an in-stack cascade cyclone was used. Preliminary field testing shows positive results.

Jan 1, 2003

By James R. Norris, Thomas A. Conto, Gary R. Walter

For at least five decades, a plume containing acidic metal-bearing water has been moving through the shallow alluvial aquifer along Pinal Creek in the Globe-Miami area. Two chemical facies of water are distinguished in the alluvial aquifer: (1) a metal-rich acidic plume with gram per liter concentrations of metals (primarily iron) and pH values between 3 and 5 and (2) neutralized water with a pH greater than 5, low concentrations of metals, and high concentrations of sulfate and manganese. Historically, the acid plume has moved through the aquifer at an average velocity of 0.6 m/day, ten times slower than the average pore velocity of groundwater in the aquifer calculated using the Darcy equation. The rate of migration of the metal-rich plume is retarded by pH-dependent chemical reactions between acid water and the aquifer matrix. As acid water is neutralized by reaction with calcite, rising pH conditions in- crease the oxidation rate of iron and decrease its solubility resulting in the precipitation of ferric hydroxides. The formation of ferric hydroxides is a proton releasing reaction which main- tains acidic conditions. The acidit of the plume and the neutralization capacity of tKe aquifer are best assessed in terms of the iron content of the water and not the hydrogen ion activity computed from pH measurements. The parameters controlling plume migration are: (1) the calcite content of the aquifer (2) the iron acidity of plume water, and (3) the rates of acid neutralization and ferrous iron oxidation. A numerical solute transport and reaction model based on the concept of iron acidity effectively simulates the historical development of acidic conditions, predicts the behavior of the plume, and was used as a management tool to identify the most efficient and cost effective remedial strategy.

Jan 1, 1991

By Deepak Malhotra, William F. Riggs, Edward C. Dowling

INTRODUCTION Mining companies are In the business of making an acceptable profit on their Investments, It became obvious in the recent recession that economic profitability/viability depends on being the lowest cost producer In order to compete on a global basis. The burden of achieving this objective falls on the mineral manager. He must strive to produce a salable product in an environmentally acceptable process while continuously Improving the profit margln.(1,2) Metal prices fluctuate on a regular basis. They directly Impact revenue and hence operating philosophy. The mineral engineer needs to develop an optimum operating strategy to meet his overall objectives, One would expect that, In the modem era of complex computer models, it would be easy to develop an economic model to maximize profits and/or cash flow. Discussions with mill managers Indicate that one mine/corporation's optimum operating strategy is not necessarily optimum for another. This paper approaches the problems from basics "Economics 101" and Illustrates the complexity of developing a universal model which can be applicable to all mines. Case examples are used to illustrate the need for better communication to avoid the basic economic fallacy “that optimization of segments leads to optimization of the whole system.” TECHNICAL MODELS Technical models are a prerequisite to the development of economic models because they provide the necessary Input data to these models, The flow of material from a mine through the sale of the finished product is shown In Figure 1. The ore Is mined and milled, and the concentrate can be stored for sale or smelted and refined In-house or at a toll facility. The finished product(s) are held In Inventory until sold either through existing contracts or in the spot market. [ ] Fairly reliable technical models have been developed for mining, milling and smelter operations. Mine plans are developed to provide a good Indication of the relationship between production and cut-off grade. It is easier to change surface mine plans than plans for underground mines. However, there are limits to maximum production that can be achieved with existing equipment. It Is possible that mine benches may not be developed to handle additional equipment, even If It was purchased to enhance production. More often than not, the cut-off grade Is lowered to Increase throughput goals.

Jan 1, 1993

By G. Argyris

A number of important studies, ongoing environment monitoring efforts and mining and road construction projects in the lignite based electrical power production area of Amyntaio ? Ptolemais in North West Greece require an accurate and up to date model of the topography. In recognition of the importance of such a model, a project was initiated by the Laboratory of Mining Information Technology and GIS Applications in the Department of Geotechnology and Environmental Engineering of the Technological Educational Institute of Western Macedonia. A massive surface triangulation model was generated from vector data using an optimized Delaunay based method. Combined with aerial and satellite imagery, the triangulation model provides a complete 3D terrain model of the area characterized by high levels of accuracy, detail and realism. The generated model is easy to modify with new data in order to improve its detail and keep it up to date with ongoing earth moving and development operations in the area.

Jan 1, 2008

By Giovanni Barla

This paper examines the application of gelatin mixture models to the study of factors such as gravity effects, tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space. The calibration technique of gelatin mixtures, proposed by Richards and Mark in 1966, is applied to the particular problem considered. Similitude relationships between model and prototype are discussed with reference to the constitutive equations describing the physical behavior of the rock mass. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example, with the view of describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving.

Jan 1, 1968

By S. Lefond

A glance at the accompanying table and a review of contributors' comments suggest that the industrial minerals industry is recovering from the recession of the past few years. Actually, the total value of nonmetal production in 1983 was $15.5 billion, up 10% over 1982. Nonmetallics still have not recovered to 1981's high of $25.3 billion, but at least it is on the way up. It is significant that cement (+20%), clays (+13%), gypsum (+16%), sand and gravel (+12%), sodium carbonate (+7%), and crushed stone (+11%) are up. These commodities are largely used in the housing and construction industries. Raw steel and steel mill products, iron ore production and castings, and purchased scrap are showing improvement and increased in value last year. They are, however, still not up to the high of 1981. These industries consume considerable amounts of many industrial minerals, such as limestone, dolomite, fluorspar as fluxes, and many types of refractories.

Jan 5, 1984

By W. W. McClintock

A column flotation system was designed to conduct release analyses of a very finely disseminated, stratiform, copper ore from the Denali Copper Prospect, Alaska. Chalcopyrite is finely disseminated in a carbonate matrix and pyrite is disseminated in both the chalcopyrite and gangue, requiring grinding to 20 microns for adequate liberation. A 25 mm x 2.4 m glass flotation column was designed. The ore and its flotation tailings were repeatedly floated to obtain a rougher concentrate, which was repeatedly floated to produce release fractions. These were analyzed for copper, iron calcium and magnesium. Release curves were plotted. The procedure was replicated at each of two grinds; 99% and 88% passing 37 microns (400 mesh), and should find application for flotation characterization and process selection. Bond grindability work was also conducted.

Jan 1, 1994

By S. S. Klima, D. E. Pollock, J. A. Organiscak

"Airborne respirable coal dust capture by water sprays or wet scrubbers has been studied and developed over many decades as an engineering control to reduce dust exposure in coal mines and combat coal worker pneumoconiosis. Empirical relationships and deterministic models for particular dust capture experiments have previously been devised to show the key parameters involved in airborne coal dust capture. Many of the results from these models show that the significant parameters related to airborne dust capture are water spray pressure, water quantity, water droplet size, relative water droplet-to-dust particle velocity, and total operating air pressure of the scrubber. However, many airborne dust capture efficiency relationships and models developed for particular experiments cannot be readily applied to forecast the dust collection efficiency of different spray and scrubber design configurations, which rely on several key dimensional engineering measures. This study examines engineering measures from previous water spray and wet scrubber experiments conducted by the U.S. National Institute for Occupational Safety and Health (NIOSH) and the U.S. Bureau of Mines (USBM) to develop empirical models for wet collection of airborne dusts. A dimensionless empirical model developed for predicting airborne dust capture efficiency of water sprays and wet scrubbers is presented. IntroductionWater sprays have been one of the earliest mainstay engineering controls used to suppress respirable dust in underground coal mines. Some of the earliest reports of water spray usage on continuous mining machines indicated respirable coal mine dust reductions of 20 to 60 percent (Kobrick, 1970). Not long after the enactment of the 1969 Coal Mine Health and Safety Act, the U.S. Bureau of Mines (USBM) and others conducted extensive research into water spray and wet scrubber systems to control respirable dust in coal mines. The primary aspects of water spray dust control included prewetting for dust prevention, localized ventilation redirection and airborne dust capture, which are summarized in handbooks or best-practices guides (Kost, Yingling and Mondics, 1981; Kissell, 2003; Colinet et al., 2010). Initially, underground studies were conducted to identify the primary sources of dust during the mining processes and effective dust controls (Courtney, Jayaraman and Behum, 1978; Jankowski and Organiscak, 1983). Laboratory research systematically studied ventilation and airborne dust capture effects of water sprays and scrubbers to improve their application in underground coal mines (Tomb, Emmerling and Kellner, 1972; Divers and Janosik, 1978, 1980; Grigal et al., 1982; Ruggieri et al., 1983; Jayaraman, Jankowski and Kissell, 1985; Volkwein, Ruggieri et al., 1985; Jayaraman, Schroeder and Kissell, 1986; Divers, Jankowski and Kelly, 1987; Jones and James, 1987)."

Jan 10, 2018

By J. Felipe Costa, Andrew H. White, Marcot T. M. B. Vilhena

Ordinary kriiing (OK) is an interpolation algorithm mostly used in earth sciences applications where it provides satisfactory results. Robust kriging (RK) is an alternative algorithm which at- tempts to minimise the problems caused by the existence of outlier values within a given data set. Robust kriging essentially consists of an editing step prior to running the traditional OK method. This study compares the interpolation results obtained by OK and RK. Two data sets were used. The first data set consists of 140 samples mimicking a drilling survey named cluster.dat. An additional feature of this sample data is that its parent population, the reference data set, is available, thus permitting direct quantitative assessment of the effectiveness of a given estimation technique. The second data set consists of a grid sampled at 1x1 m. The estimates obtained by OK and RK using cluster.dat were compared to the reference data set. RK provided better results in terms of quality of the estimates than OK

Jan 1, 1996

By K. Luxbacher, A. Haghighat, B. Lattimer

Mine face ignition due to high levels of methane is one of the most common fire incidents in underground coal mines. In continuous miner headings, depending on the magnitude of the ignition or resulting fire, auxiliary ventilation controls may be damaged or dislodged, affecting the ventilation into the area. A computational study was conducted to investigate the effects of different levels of damage to an exhausting ventilation curtain in a continuous miner heading, and the impact on ventilation to the face. The computational fluid dynamics software Fire Dynamics Simulator (FDS) Version 6.0 was used to predict the conditions that develop due to a 200-kW fire in the face following a methane ignition with different levels of assumed ventilation curtain damage. Smoke layer depth, temperature and mass flow inby the last open crosscut were used to evaluate the impact of no damage to the curtain, partially dislodged curtain, and fully removed curtain. As more of the ventilation curtain was damaged, smoke depth and temperature outby the fire increased. With the full removal of the curtain, the smoke accumulated from the last open crosscut to the face, with the ventilation completely bypassing the continuous miner region.

Jan 1, 2016

By Winfield G. Wright, Philip L. Verplanck, Philip L. Hageman, Douglas B. Yager, Dana J. Bove, M. Alisa Mast

Geological, hydrological, and geochemical information synthesized in a Geographical Information System (GIS) for water and rock surrounding South and Middle Forks of Mineral Creek, northwest of Silverton Colorado, was analyzed to distinguish between the natural and the mining-related sources of metals to dace waters in the watershed An important natural source of metals to surface water emanates from a porphyry molybdenum deposit south and upslope from the Middle Fork of Mineral Creek. Interaction of surface and ground water with fractured, altered rocks and permeable, Quatemay-age surficial deposits produces downstream water quality that does not meet current State of Colorado water quality standards for metals and pH. GIS site characterization and three-dimensional modeling distinguish surficial deposits as volumetrically substantial, significant sources of naturally occurring metals that strongly influence water quality and complicate ongoing mine-site mitigation efforts. Our findings indicate that regional hydrologic and geologic information needs to be evaluated before realistic water quality guidelines are established and mitigation recommendations are confidently implemented.

Jan 1, 2000

By Garland R. Dever

Limestone resources for industrial, constructional, and agricultural uses occur on the surface and at minable depths in several areas along the Ohio River and its navigable tributaries in Kentucky. Operable thicknesses of high-calcium and high-carbonate limestones suitable for use in cement and lime production, steel manufacture, environmental-control measures, and other special uses are documented in Ordovician and Mississippian formations by analysis of 0.3-meter (foot-by-foot) samples. Active and potential mine and quarry sites afford access to water transportation and proximity to a number of industrial and metropolitan centers. Geologic factors affecting the distribution of deposits include the Cincinnati arch, regional dip into the Appalachian and Eastern Interior basins, complex faulting in and near the Western Kentucky fluorspar mining district, and late Paleozoic erosional unconformities in northeastern Kentucky.

Jan 1, 1977