Search Documents

By J. Carr

Ring gear and pinions used as the final drive on large metallurgical grinding mills are expected to transmit their rated horsepower reliably for long periods of time. Duty is 24 hrs./ day. Life expectancy of such gear sets is of the order of 20 years; that is, each gear and pinion flank is expected to resist failure by pitting for 10 years. This means that for a dual pinion gear set having a ratio of 18.42:1.0 and a mill speed of 10 RPM, every gear tooth will see 105.12 x 106 surface contact stress cycles and every pinion tooth will see 968.15 x 106 surface contact stress cycles in a 10 year period. The allowable surface contact stress on the gear and pinion is determined by the material hardnesses. The rule being the higher the hardness, the higher the allowable surface contact stress may be.

Jan 1, 1985

By James E. Lawver

During 1981 the Florida phosphate industry produced more than 43 million metric tons of phosphate rock - about one-third of the entire world production and also generated nearly an equal amount of waste clay and waste clay-sized product that requires dewatering and disposal. The material balance of solids and water for a typical Florida phosphate mining operation is shown in Figure 1. Historically, the industry has impounded clay waste (about 60% below ground and 40% above ground) in earthen dams, often as large as 800 acres and occasionally greater than 60 ft. high. The dams have served the triple purpose of: 1. Dewatering initial 3% solid waste clay for process water re-use. 2. A reservoir system to minimize water discharge from the mining area and to capture and store rainwater thus minimizing deep well pumping requirements. 3. The ultimate densification and storage of waste clay.

Jan 1, 1983

By Zhen-xing Diao, Feng Zhao, Ya-dong Xue

"Two important aspects of excavation performance of TBM are advance rate and cutter replacement/ring consumption, which is closed to the cost and construction duration of the project. To achieve this, a database of TBM parameters and the geological-geotechnical conditions during the excavation of Yinhanjiwei was compiled and analyzed. Relationships between different geological and TBM operational parameters were investigated. Results of analyzes show that there are qualitative correlation between Field Penetration Index (FPI) and rock geological parameters. And strong relationships between FPI and operational parameters are suggested. In this study, the cutter replacement and ring consumption were analyzed using statistical method for preliminary estimation in similar conditions. 1. ITRODUCTION Hard rock TBM is widely used in tunneling project nowadays because of its advantages to conventional drilling and blasting, especially in long tunnels. The biggest advantage is its high advance rate. However, rock conditions of tunnels are complicated. So TBM performance becomes a primary topic in tunneling engineering, which includes of rate of penetration, utilization, daily advancement, cutter consumption and so on. Many prediction models have been developed to estimate the TBM performance in the project planning phase. The most widely accepted and used models around the world are semi theoretical CSM model (Rostami and Ozdemir, 1993; Rostami, 1997) and the empirical NTNU model (Blindheim, 1979, Bruland, 1998).With increasing uses of TBMs in different ground conditions, an increasing number of researchers have developed new models in order to predict the performance of TBM more accurately in similar geological conditions.(Gong and Zhao, 2009; Hassanpour et al.,2009, 2010, 2011, 2014; Delisio et al., 2013; Delisio and Zhao, 2014)"

Jan 1, 2016

By P. A. Plunkert, D. E. Morse, L. McCartan, S. F. Sibley

Following the recession of 2001, restrained consumer spending, declines in domestic manufacturing and industrial output, and increased unemployment led to a lack-luster year in the domestic economy. In 2002, the U.S. real gross domestic product (GPD) grew only 2.4%. Significant production declines in the U.S. metals industry were registered by copper, lead and zinc producers. Steel producers, despite a slight improvement in shipments, continued to face strong foreign competition, higher energy costs and lower prices for their products. Homebuilding and other domestic construction sectors— major consumers of nonmetallic mineral products such as cement, brick, glass and stone — remained strong enough to help raise the output of industrial mineral materials slightly above 2001 levels. A strong U.S. dollar relative to other national currencies continued to weaken the competitive stance of U.S. metal and non-metal mineral materials companies alike against foreign producers in markets at home and abroad.

Jan 1, 2003

By Jack E. Thompson

I have spent my entire life in the mining industry pursuing what I believed was an honorable profession that provided products that were critical for our social and economic well being. Now I am told that all of my efforts been for nothing and that I have been doing something morally wrong - mining. This view of the future is not one that the mining industry has to allow to unfold. A determining factor in how things will turn out is continued improvement of the industry's environmental performance. To some extent, the current state of affairs in the United States is a result of the common perception that greedy corporations (usually foreign) are somehow ripping off US citizens of their native birthright or natural treasures in the name of corporate profits. Implicit in this view is the belief that corporations will take shortcuts or violate the environment in the name of profits. I have 26 years of experience in working in the copper, uranium and gold industries. Profits during those years were meager and difficult to find (Fig. 1). In fact, when I began working fresh out of college, I chose copper, which was then selling at around $1/lb. By the time I left copper mining, it was selling for 45 cents/lb. I then moved to uranium, which was selling for $52/lb. By the time I left it was $16/lb. I finally picked gold, which was then at ($650/oz). There is a whole generation of engineers, geologists and professionals who have spent two decades downsizing, closing mines, improving costs and getting smarter about how the mining industry does what it does. The environment, health and safety are areas where there have been great improvement. There are five characteristics of corporate governance that are critical for a company to develop and an industry to embrace if environmental, health and safety excellence is to reach new heights in the labor pool.

Jan 1, 1997

By Manfred Jaeger, Klaus Ertmer, Walter Dietrich, Jochen Greinacher, Wilhelm J. Kogelmann

In Europe, novel low-cost excavator-mounted Multi Tool Miner (MTM) systems, consisting of cutter head, hammer, bucket and drill attachments permit one unit to perform multiple tasks replacing several purpose-built machines. At the Weser Tunnel in Germany, cross-passages between the twin tubes were excavated in frozen ground with a remote-controlled mini-excavator equipped with a quick-change cutter head, ripper tooth and bucket. In Switzerland at the N2 interstate near Basel, W. Dietrich AG enlarged a 2-lane tunnel to three lanes with a cutter head mounted on a special excavator. Blasting and heavy hammers were not permitted due to the closeness of the “live” twin tube. At the N20 Zurich bypass, the Joint Venture of Jaeger, Frutingerand AHB excavates highway tunnels, some with extremely large cross sections, conventionally. A cutter head mounted on an excavator removes the rock shattered by blasting precisely to the pay line, thus preserving the rock’s self-supporting capacity preventing subsidence and damages to water resources and buildings on the surface under low overburden.

Jan 1, 2003

By W. C. Goldberg

This paper presents pit slope monitoring and back-analysis case studies con-ducted to evaluate and, if possible, stabilize slopes at the Berkeley Pit in Butte, MT. Two specific slopes were studied in detail. The first slope was determined to be near limiting equilibrium, as evidenced by its response to the initiation and cessation of mining, while the second failed on three occasions. Back-analysis of the failed slope verified the laboratory-derived geomechanical properties of the earth materials. Early detection of slope movement can show a need to take action, including modifying slope geometry, dewatering if the slope were wet, and/or investigating and implementing artificial supports. Monitoring slope displacements in open-pit mines can supply data for predicting collapses and preventing serious damage, injuries, and/or loss of life.

Jan 1, 1989

By H. Douglas Dahl

Thank you, Don Gentry, for your generous introduction. It is not adequate simply to say that I appreciate very much the vote of the Award Committee putting forth my name as the winner of the 1992 Daniel C. Jackling Award. To look at the list of previous Jackling Award winners is a humbling experience. The Society for Mining, Metallurgy, and Exploration has been blessed with some exceptional members over the years, and I feel privileged indeed to be included among the Jackling Award winners. During the years of my education at Penn State, my field of specialization was mining engineering, with particular emphasis in my master's and Ph.D. work on rock mechanics. But my career has not been quite so tightly focused as that. I have been involved with coal mining in all its variety - its technical aspects, both theory and practice; and its business side, dealing with management and labor, accountants and lawyers, politicians and environmentalists. And I have also been involved with related fields - construction; exploration; barges, railroads, ships and docks; supply houses; the coke business; you name it. Coming from that practical background, I believe it is most appropriate that I talk with you today about some practical matters. But I will not advise you today how to mine coal or protect roof in a hard-rock mine. You fellows know how to do that. The practical matters that I have in mind relate to policy - national policy. I will acknowledge immediately that national policy is often much less than practical, but bear with me as we explore the subject together. I am reminded of a supervisor I had early in my career. He very strongly advised me, back in 1961, to "get involved in the political process," for without objectivity injected into our national policy making, we will become a second-rate economic power. I have selected as the subject of my remarks today, "Coal and the de facto National Energy Policy." There is an energy policy relating to coal, a de facto one, and it's the one we see as a result of regulation, attitudes and culture from our nation's capital. This de facto policy is the one we in the coal business live with every business day. My thesis is very simple - Coal is, in fact, a vital part of our national energy policy and will remain so, as a practical matter, no matter what politicians may do to us, or not do to us. Coal will prevail - that will be the happy ending to my story in which, of course, we are the good guys in the black hard hats. But first, I must flesh out the plot with some other characters and with some threatening activities. There are five main characters in my story: in order of appearance - Perpetual Politics, Rampant Regulation, Selective Science, Electrification and Confident Coal. The time: the present. Perpetual Politics is always a threat to coal. When you cross the Capital Beltway into Washington, D.C., check your wallet and your gold fillings, because you're not likely to run into any friends. On Feb. 20, 1991, just over one year ago, President Bush presented to Congress his National Energy Strategy. It's a thick document of more than 260 pages, with discussions on securing our future energy supplies, increasing energy effi-

Jan 1, 1993

By Brain W. Lawrence

Sublevel stoping generally is a large-scale open stoping method. It sometimes is referred to as long-hole or blasthole stoping. This method usually is applied to strong ore bodies that require minimal support and are surrounded by strong country rock. The ore body should be fairly regular in shape and well-defined. The dip of the footwall normally should be sufficient to allow broken ore to gravitate freely, although the method has been adapted successfully to mine some of the flatter ore bodies. Sublevel stoping is not dependent on the width of the ore body. Widths of less than 6 m (20 ft), however, make the utilization of long-hole drilling techniques more difficult. The main criteria for sublevel open stoping are competent ore and stable host rock, regular ore boundaries, and a footwall dip that exceeds the angle of repose of broken ore. Basically, the method entails providing access to the ore body at various subintervals between the main haul- age levels in order to drill and blast the intervening ore. Stope drilling is carried out from drilling drifts on the sublevels, and the ore is blasted in slices towards an open face, which generally is vertical on the downholes and may be inclined towards the open face for the up holes. The blasted ore gravitates to the bottom of the stope and is collqcted through drawpoints. Fig. 1 illustrates a typical sublevel stoping mine. The method requires extensive ore body development with relatively high capital expenditures. How- ever, much of the development is in ore, and production costs are comparatively low. Productivity rates are in the 13.6 to 27.2 t (15 to 30 st)/manshift range. The drilling, blasting, and loading operations are performed independently, and equipment utilization is high. Large outputs can be obtained with few units and limited personnel. Dilution with waste rock may occur if ore boundaries are irregular or if caving occurs, but 100% of the ore within the stope usually is recovered. Pillar recovery sometimes is a problem. It is at this point that most of the waste dilution occurs. At the time data was gathered for this report (1973), the sublevel open stoping method was used by more than 21% of the metallic ore mines in the US (9 out of 42 mines producing 1088 + t/day (1200 + stpd) and provided more than 12% of the total metallic ore production from these mines. DEVELOPMENT Access to a sublevel open stope mine is gained by a slope or shaft that is normally sunk in the footwall of the ore zone, away from any possible effects from blasting or other production operations in the stoping process. Main level interval is selected and usually varies from 45.7 to 121.9 m (150 to 400 ft), depending on the vertical extent of the ore body, the number of drawpoints required to maintain output, and the eventual stope height. The main haulage drifts are located at the bottom of the stope horizon, either directly in ore or in the footwall, with access crosscuts at intervals. Raises are driven up through the ore to connect to the level above and provide access and ventilation to the sublevel drilling drifts, which are driven horizontally in the ore for the length of the stope. Depending on the drawpoint system to be used, the stope is either undercut by a raise-and-cone system, from a scram or slusher drift, or simply provided with a drilling drift from which access is made at intervals to the main haulage level. A raise driven either at the end or in the middle of the stope (if stope access is from both ends) provides a start for opening up a vertical slot across the stope to establish a free or open face for long-hole drilling and blasting. Sublevel stoping has proved to be a relatively safe and economical system.

Jan 1, 1982

By David Conover

The El Boleo Copper Project is currently in the final design stages for development of a 3-MM-tonne/yr underground copper mine located in Baja California, Mexico. The nearly horizontal mineralized zones are amenable to exploitation by conventional mechanized coal mining technology using continuous miners, shuttle cars, and belt haulage. The mine design resembles a typical full-extraction coal mining operation utilizing a sequence of mains, sub-mains and production panels. Due to numerous faults, mining will be conducted as several small adjacent mines accessed through adits from large arroyos cutting through the mine area. Up to four seams may be mined in some areas with a maximum overburden depth of about 250 m. The ore zone is relatively weak and plastic, subject to extensive creep over time. The mine workings will pass through areas of historical shortwall mining panels where the ground has flowed into old entries and gob areas, and then reconsolidated. A small test mine was developed to evaluate mechanical cutting performance, roof-bolt anchorage capacities, roof and pillar stability and caving behavior. In-mine measurements were combined with two- and three-dimensional FLAC models to evaluate alternative development and production pillar designs. The paper will discuss the various factors influencing ground stability at the El Boleo project and the strategies employed in developing a suitable ground control design.

Jan 1, 2009

By Dale W. Norris

United States Steel's Cumberland Coal Operations is located in Greene County in the southwest corner of Pennsylvania. The mine and related facilities have been in operation since September of 1977. Production from this mine, U. S. Steel's first commercial coal mining venture, will eventually reach a level of 2.72 million mt of clean coal per year and is totally committed to electric power generation. Cumberland is a slope mine in the Pittsburgh seam and is mined by continuous mining machines and longwall. The coal from the mine is trans- ported by belt to the surface, taken through a rotary breaker for initial preparation, and stored in raw coal silos. It is then processed through the preparation plant and taken to a clean coal silo where it is held for train loading. Cumberland Mine operates its am 28.16 km railroad to transport the coal to the Monongahela River. The unit train consists of thirty-one 90 mt cars. The coal, once loaded on barges, is then shipped to the customer. Cumberland Mine is one of the most modern coal preparation and unit train loading systems in the nation. The preparation plant is de- signed to receive coal from the silos at a rate of 720 at per hour. The +6.35 mm material is screened out and cleaned in a Daniels heavy media vessel with two 3.35 m weirs. Minus 6.35 mm material is fed to sixteen #88 Deister concentrating tables. The cleaned coal from this circuit is dewatered, and all effluents from the mechanical dewatering report to the classifying Cyclone sump for classification through ten 35.6 cm cyclones. The cyclones overflow material (-150 mesh) is processed through two banks of three 8.5 m3 Denver D.R. flotation machines. The cyclone underflow pro- duct (28-1 0 mesh) is processed in two banks of 5 six 2.83 m Denver Sub A machines. The clean flotation product is then dewatered in Bird screen bowl centrifuges, blended with the other clean coal size fractions, and the total plant product further dewatered in a thermal dryer.

Jan 1, 1980

By William G. Freeman

In comparison to many mineral commodities, barite has a low unit value. It is mined and sold in low volumes in high-grade (90-98% BaSO4) forms to basically one industry that uses approximately 75% of the free world production. Based upon the above criteria, all factors must be considered in determining if a barite deposit is economical; such as, the type of deposit, mining and milling methods required, transportation to the markets, tariffs, local political conditions, etc. In other words, barite mines are made--not found. The length of this paper precludes any indepth discussion of geology, mining and metallurgy of barite. Most of this information can be found in data already published, such as D. A. Brobst's bulletin1 on the Barite Resources of the United States.

Jan 1, 1971

By Clayton J. Parr

Introduction This chapter contains brief discussions of various environmental protection requirements that relate to underground mining operations. Environmental disturbances at an underground mining operation can result from subsidence; water discharges; waste dumps; construction and operation of access roads and utility lines; construction and operation of surface facilities such as maintenance shops, bathhouses, and storage yards; and emanation of dust and noise from surface crushers. Construction and operation of a concentrator or washing plant may result in the emission of air pollutants, the discharge of water pollutants, the creation of noise, and disturbance of the surface. Tailings ponds can be the source of fugitive dust.1 This chapter is not intended to provide a detailed discussion and analysis of laws and regulations dealing with environmental protection. Rather, its purpose is to provide the engineer with a basic awareness of the existence and nature of such laws and regulations, as well as the procedural requirements that must be followed in complying with them. The body of law relating to environmental protection has grow" very rapidly and should continue to do to for some time. Because many of the laws have been enacted recently, numerous court decisions are being rendered to resolve disputes over their interpretation. Hence, the reader is cautioned to be alert for subsequent modifications of statutes and regulations, and new case law. Rules and regulations pertaining to environmental protection are implemented at all governmental levels. The most widely known laws are those enacted by the federal government that have nationwide applicability. However, separate requirements exist in each state, county, and municipality. Because of their general applicability, federal laws are discussed most extensively in this chapter. Ownership of the property is the most significant factor considered in ascertaining what rules govern the conduct of an operation thereon. If the land is held under lease, reference to the lease terms must be made in the first instance to determine what obligations must be met in order to prevent default and possible loss of the property. If the land is held under a lease from the federal government, the operator is subject not only to compliance with the lease terms, but also to a large body of laws and administrative regulations that pertain generally to the conduct of mining operations on land held under federal leases. Although operations on unpatented mining claims, the legal title to which remains in the federal government, are not subject to the same rules and regulations that are applicable to operations conducted pursuant to federal leases or permits, they soon will be governed by a special set of regulations that provide for protection of surface resource.2 Operations conducted on lands leased from a state usually are subject to numerous environmental protection requirements specified in the lease terms, in addition to rules and regulations promulgated by the state agency having jurisdiction over mining on state lands. Operations conducted on privately held lands are subject to fewer such requirements. Leases from private parties sometimes have environmental protection and reclamation requirements written into them, but generally to a far lesser extent than governmental leases. Operations conducted on properties owned by the operator are subject only to those laws and regulations that have general applicability without regard to land ownership. COAL SURFACE MINING CONTROL AND RECLAMATION ACT OF 1977 Introduction On Aug. 3, 1977, the Federal Surface Mining Control and Reclamation Act of 1977 was signed into law.3 It governs coal-mine operations on private lands, as well as on public lands. The Act is pervasive in its scope and is extremely long and complex. The basic purpose of the Act is to control and minimize the environmental effects of surface coal mining. Surface coal-mining operations are defined as activities conducted on the surface of lands in connection with a surface coal mine and surface impacts incident to an underground coal mine.4 The Act is administered by the Secretary of the Interior through a new agency named the Office of Surface Mining Reclamation and Enforcement.5 The Act contains detailed environmental protection standards and reclamation requirements, and it establishes a permit system for all surface coal-mining operations. Mining in certain areas and under ceri-in conditions is restricted or prohibited, and a mechanism for enforcement by the states is provided. Stiff penalties are provided in the event of noncompliance. Implementation Schedule Nonfederal Lands: As required by Section 501 of the Act, interim regulations setting mining and reclamation performance standards based on and incorporating standards set out in Section 502(c) were adopted effective Dec. 13, 1977.6 They will. be incorporated as amendments to Chapter VII of Title 30, Code of Federal Regulations. Permanent regulatory procedures for surface coal-mining and reclamation operations performance standards, which were directed to be promulgated by Aug. 3, 1978, were published in proposed form on Sept. 10, 1978. 7 They govern surface coal-mining operations in any state until a permanent state or federal program is adopted. As of Feb. 3, 1978, all new operations, and as of May 3, 1978, all existing surface coal-mining operations, on lands on which such operations are regulated by a

Jan 1, 1982

By W. K. Collins, C. L. Dahlin, D. C. Dahlin, W. K. O’Connor, G. E. Rush

Direct mineral carbonation has been investigated as a process to convert gaseous CO2 into a geologically stable final form. The process utilizes a slurry of water, with bicarbonate and salt additions, mixed with a mineral reactant, such as olivine (Mg2SiO4) or serpentine [Mg3Si2O5(OH)4]. Carbon dioxide is dissolved into this slurry, resulting in dissolution of the mineral and precipitation of magnesium carbonate (MgCO3). Optimum results have been achieved using heat pretreated serpentine feed material and high partial pressure of CO2 (PCO2). Specific conditions include: 155°C; P002=185 atm; 15% solids. Under these conditions, 78% conversion of the silicate to the carbonate was achieved in 30 minutes. Process mineralogy has been utilized to investigate the appropriate feed characteristics, identify the process products, and interpret the mineral dissolution and carbonate precipitation reaction paths.

Jan 1, 2001

By P. Somasundaran, H. S. Hanna

The separation of minerals such as apatite and scheelite by flotation from other salt-type minerals such as calcite is extremely complex owing to the close similarity between their physicochemical properties. In this paper, properties relevant to flotation such as crystal structure, solubility, surface charge and adsorption behavior of important salt-type minerals are examined along with the role of inorganic modifying agents such as silicates and polyphosphates and organic modifying agents such as starch and tannin. Flotation characteristics of these minerals are then reviewed and selected separation problems involving salt-type minerals are discussed.

Jan 1, 1976

By M. S. Davis

The Tek Process can produce masonry products such as bricks, roof or wall tiles, and block from virtually any inorganic waste. In the process the aggregate raw materials, portland cement, water and common chemicals are first mixed together; then mechanically subjected to several thousand pound pressure per square inch. This causes a novel chemical reaction between the cement, chemicals and water; producing the "patented" Tek adhesive binder which holds the aggregate together in a stone-like mix. Simultaneously, the desired product shape is formed. The building modules can have strengths of 8000 p.s.i. (pounds per square inch) with completely sound aggregates utilizing air curing for a period of 28 days. With most aggregates, 3000 p.s.i. is achieved within 24 hours. Eventual strengths usually exceed 5000 p.s.i. with almost any raw material. Water absorption ranges from 5-7.5 percent. Both absorption and strength figures are superior to the most rigid of any and all A.S.T.M. specifications for the highest quality bricks. In most locations, the product (when brick shaped is called Tekbrik) can be produced significantly more economically than can comparable grades of clay or other bricks, be- cause almost any inorganic waste materials or pollutant can be used as a raw material. The process results in a lower manufacturing cost as compared to clay bricks; fuel cost to operate a clay kiln represents a substantial portion of the total cost. Capital expenditure for a Tek plant also is lower due to the large investment in clay kilns. Transportation savings also are important, clay brick factories must be very large because the kilns are uneconomical unless they are large. Most bricks are manufactured at the sites of clay deposits in relatively uninhabited areas. The cost of transportation to the job site represents a considerable percentage of the selling price.

Jan 1, 1974

By J. J. Komadina

Since the advent of resin-in-pulp (RIP) technology for treatment of uranium-bearing ores in the 1950?s to current carbon-in-pulp (CIP) processing of gold values, metallurgies and operators alike have wrestled with the problem of interstage screening. Early gold CIP plants such as at Homestake utilized externally mounted vibrating screens in conjunction with air lifts to effect carbon-pulp disengagement. Other operations world-wide have likewise adopted this technique with varying degrees of success. Subsequent development of in-tank launder screens both in South Africa and the United States have been of the air cleaned variety (EPAC)

Jan 1, 1988

By Peter J. King

Demand for both lead and zinc to the year 2000 will be characterised by modest to nil growth in mature economies, with positive 3 to 4 per cent annual growth rates in developing nations. Asia and China will feature significantly in this growth. Overall lead demand is expected to grow about 1 per cent a year, with industry becoming more dependent on the fortunes of the automotive industry as the lead-acid battery will be the only major end use to expand. Zinc will become more dependent on its main use, galvanising, as the automotive and construction industries move to high levels of dependence on corrosion prevention. Strong growth in zinc consumption in S.E. Asia, China and India is likely to feature widespread development of the continuous steel strip mini-galvanising line technology. Thank you Mr. Chairman for inviting me to this Conference. As an Australian I am honoured to be here to offer some thoughts about future trends in metal consumption -- with particular reference to the role of countries in my own neighbourhood, the developing Asian nations, including China. It is customary for a member of the producer fraternity to speak to the topic of future development. This is no doubt due to the fact that our companies are so often engaged in endeavours to determine the future prospects of the metals as essential background to massive investment decisions relating to the development of new mines and smelters. This is sometimes also applied in relation to the more painful decision of closures of aging operations. In this paper I have drawn upon recent studies by AM&S into the future of lead and zinc. While this work has been thorough and skillful, we are nonetheless left with uncertainty on a number of counts. Firstly. predictions in the past in our industry have not been all that credible. Need I remind a U.S. audience for instance of the Paley ' investigation setup by President Truman in 1950 to study U.S. copper requirements for 25 years in the future. Asarco's Simon Strauss gave those of us daring to forecast long term commodity trends a salutary reminder that the Paley Commission with all the expertise at its disposal missed the mark in its copper predictions by a very wide margin indeed. Additionally, it is difficult to take comfort from longer term economic forecasts. Too many important economic issues remain unresolved suggesting considerable caution. These include the threat of growing protectionism; low economic growth rates with stubborn unemployment levels; and levels of government expenditure at near saturation as a percentage of GDP, to name a few. However, on a more optimistic note. we can look to China, where there appears to be momentum in its economic growth; oil, where stable oil prices to the mid 1990's will contribute to inflation control; and the fact that LDC debt, while still a major issue, is declining in importance and priority. In the short time allocated to us. I wish to deal succinctly with the lead and zinc raw materials supply picture, which is one I do not believe will hold too many surprises for this audience. Following the review of raw materials supply, we will turn our attention to the changes in the pattern of demand towards the year 2000. emphasising the Asian position. In this context. I would like to focus on the theme of the changes in OECD consumption levels relative to those of the emerging nations. One area we will be paying special attention to is China.

Jan 1, 1986

By Sathit Tandanand

Geological differences among various coalfields restrain the applicability of subsidence prediction using existing European methods. To modify these methods for domestic conditions, the Bureau of Mines, U.S. Department of the Interior, developed a method of assessment to evaluate the lithological effects on subsidence in the Northern Appalachian basin by examining data collected from 16 longwall panels in the coalfield. The assessment is partially completed, and the results to date show that the ratio of maximum subsidence to the extraction thickness, known as the subsidence factor, can be expressed in terms of the width-to-depth ratio by a simple exponential equation which has a coefficient tentatively considered as the subsidence index. This index varies with the lithology of a particular site and can be expressed in terms of the percent distribution of weak and strong rocks in the overburden.

Jan 1, 1982

By R. Haecker, S. Gupta, P. Somasundaran

Rock disintegration processes are usually inefficient and costly operations in mineral beneficiation, mine development and oil well preparations. Thus, there is a strong need for improving the energy efficiency of unit operations such as drilling and comminution. The effects of selected cations and anions on drilling efficiency in a hard rock formation (Dakota Sandstone) were studied. The zeta potentials and the tensile strengths of the drilled samples were measured under similar chemical conditions. The chemicals tested included MgCl2, Na2CO3, AlCl3, NaCl and Dodecylammonium chloride. The results indicated that drilling rates can be enhanced or retarded depending on chemical conditions such as the solution pH and the type and concentration of reagents. Drilling data are correlated with mechanical (tensile strength) and interfacial (zeta potential) properties of the rock formation. The mechanisms involved are discussed in light of Rehbinder's and Westwood's theories.

Jan 1, 2000