Search Documents

By T. V. Johnson

The microstructural relationships in dolomitic fluxed taconite pellets were studied. The influence of basicity (in the range 0.75 to 2.1) and firing temperature (to 1340°C) on the grain structure, macrostructure, and mineralogical phase relationships are described. Extensive slag bonding of hematite grains begins at temperatures between 1220 and 1230°C, and results in fundamental changes in grain structure. Successive temperature increases result in little change in grain structure until 1340°C, when extensive coalescence of the hematite grains begins.' Increasing flux additions have little effect on grain structure but greatly influence pore character. The compressive strength decreases with increasing flux addition, increases with increasing firing temperature, and is related to the macrostructure of the pellet. The compositions of the slag phases are represented on the CaO-Fe2O3-SiO2 phase diagram, and the compositional path of slag development is described.

Jan 1, 1980

By Y. Gonzalez

The reaction kinetics of sulfuric acid leaching of brass foundry flue dusts were studied. As received flue dusts were separated into two size fractions, a coarse fraction (median size 103.5 microns) and a fine fraction (median size 3.4 microns). Experiments were performed on both fractions al-though most results are reported for the coarse fraction. Leaching experiments were conducted in a stirred reactor to determine those factors which govern the kinetic response of the sys-tem. The kinetics were followed by determining the increase in the concentration of dissolved copper with time. The effects of temperature, concentration and oxygen partial pressure on the rate of copper dissolution were examined. In addition, reaction residues were examined by SEM, EDAX and X-ray analysis. An activation energy of 4.8 kcal/mole (20.08 kJ/mole) was calculated. The rate was found to be significantly dependent on oxygen partial pressure and acid concentration. The order of the reaction with respect to oxygen partial pressure and hydrogen ion concentration was approximately 1.50 and 0.37, respectively. Results indicate that the dissolution reaction is limited by diffusion and can be described by the following mathematical expression where ~ is fraction of copper extracted in time t

Jan 1, 1988

By J. O. Stephens

During the late 1940's and early 1950?s, the Westinghouse Combustion Turbine Division built and demonstrated a residual oil-burning locomotive on six eastern railroads. Plans were made to convert to burning pulverized coal, and a single combustor was operated at a full-pressure condition in the laboratory for about two years. During the mid-1960's to mid-1970's, there was considerable interest in coal-burning MHD and a combustor was developed which would also be applicable to combustion turbines. In the early 19801s, the BCR National Laboratory (BCRNL) became affiliated with the University of Pittsburgh, and a program was begun, supported by the Stare of Pennsylvania, to develop an all-purpose combustor for use with industrial and utility boilers and eventually with combustion turbines. In this paper, we review the work of almost 40 years, indicate our present position, and propose steps to be taken leading to efficient and environmentally acceptable power generation from coal, and specifically to coal-burning locomotives.

Jan 1, 1986

By Evgueni Jak

Pyrometallurgy is an important sector of modern industrial society actively participating in solving current environmental, economic, materials scarcity and other challenges. Recent advances in analytical methods, experimental techniques, thermodynamic, phase equilibria and process modelling tools provide new opportunities to increase the productivity of pyrometallurgical reactors, the treatment of complex feeds and metal recoveries. Fundamental theoretical models can now be used to make a significant next step towards the development and implementation of computerised models describing real industrial processes—Virtual Reactors, and computer-aided smart-decision-making systems that may be called Pyro-GPS by analogy to GPS; these developments can facilitate knowledge-based improvement and optimization strategies. The implementation of these improvements require ongoing collaboration between researchers, industry and government

By M. L. Harris

Coal dust produced during the mining process is a prime explosion hazard in underground coal mines. To inert the coal dust and prevent a catastrophic propagating dust explosion, rock dust is applied to the roof, ribs, and floor surfaces of mine entries. Currently, one determination of whether a mine is adequately protected from the coal dust explosion hazard is made by analyzing collected mine dust samples for percent total incombustible content (% TIC). A minimum of 80% TIC is required per 30 CFR 75.403. The as-received moisture of the dust sample is included in the % TIC. Moisture and humidity within a coal mine vary greatly with the seasons, with explosions occurring more frequently during dry winter months. This paper will discuss the fluctuations of the as-received moisture content of the mine dust samples collected by U.S. Mine Safety and Health Administration inspectors in 2010 and the observed fluctuations of the moisture content of rock dust within the U.S. National Institute for Occupational Safety and Health Office of Mining Safety and Health Research Bruceton Experimental Mine and the Safety Research Coal Mine over a one-year period.

By Shangyong Lin, Wei Sun, Weiping Liu, Muhammad Azam, Junfeng Chen, Yujie Zhao, David Asubonteng, Michael Ngoie

Copper concentrates are widely used in smelting operations worldwide and typically consist of chalcopyrite ( CuFeS2) as the primary mineral, with chalcocite ( Cu2S) and bornite ( Cu5FeS4) as secondary copper-bearing minerals. However, these concentrates often contain hazardous impurities, such as the fluorine ion, which can result in various complications during the smelting process. These issues include equipment corrosion, gas treatment requirements, environmental hazards, and strained community relations. Furthermore, high fluorine content in copper concentrates can lead to penalties and limitations during sales. To address these challenges, this comprehensive review assesses current techniques for removing fluorine from copper concentrate. Drawing upon recent research and the findings in the field, the review analyzes the advantages and disadvantages of existing fluorine removal methods and identifies critical issues requiring attention in the future. This review provides valuable insights into the current state of fluorine removal from copper concentrates and serves as a practical guide for researchers and industry professionals in this field.

Aug 2, 2023

By Y. Zhang, C. Zhou, M. Girman

Wireless technologies are increasingly being implemented in underground mines for various purposes such as communications, tracking, remote control, remote sensing, and environmental monitoring. However, the adoption comes with risks as common wireless systems, such as WiFi, Bluetooth, IWT (Innovative Wireless Technologies) wireless system, often operate in the unlicensed ISM (industrial, scientific, and medical) band. The shared nature of the ISM band can lead to interference among devices and consequently cause performance degradation and reliability issues. In this study, we developed two wireless communication evaluation boards as a tool to evaluate the performance and reliability of a wireless system with the presence of electromagnetic interferences (EMI) from other wireless systems in underground environments. We adjusted various parameters including signal power from adjacent frequency channels, noise power within the same channel, the movement of personnel, and communication packet size. Our findings indicate that, while the power of the EMI source plays a key role, the motion of personnel in the tunnel also has a strong impact on performance, and this impact increases as the power of EMI sources increases. In noisy environments, smaller packet sizes are preferable as they enhance the likelihood of successful transmission. High levels of interference or noise can lead to increased packet loss or error rates, potentially causing communication links to fail completely or become ineffective. The evaluation boards utilized in this study are based on a practical wireless transmission system deployed in a remote controller for a heavy mining machinery used in underground coal mines. The results and findings presented in this paper can aid in the design of wireless systems that are resilient to EMI in underground mining environments.

Feb 1, 2025

By Alden B. Carpenter

Oil-field brines have been collected and analyzed from Jurassic and Cretaceous rocks in the Mississippi Salt Dome Basin, from Jurassic and Lower Cretaceous rocks, southwestern Arkansas, and from Ordovician and Silurian rocks, southern Michigan. All of these brines are genetically related to evaporites and appear to be brines expelled from halite-bearing rocks, presumably during compaction. The brines in rocks closest to the halite-bearing rocks are uniformly low in lead and zinc suggesting that the metals in metal-rich brines are not acquired within evaporite sequences. The metals in metal- rich brines in Mississippi and in Russia appear to be derived from red beds and may have been originally associated with ferric iron oxyhydroxides. Reduction of these compounds by migrating hydrocarbons appears to release lead and zinc to the associated brines accompanied by the fomation of authigenic ankerite.

Jan 1, 1979

By Dean Newman, Michael Behrens, Mark Trim, Justin Arifin

Road tunnels in recent infrastructure projects in Sydney, Australia, are designed to have a fire resistance level of either a 4-hour cellulosic fire or a 2-hour hydrocarbon fire. Where permanent ground support for tunnels consists of systematic rock bolts and relatively thin layer of shotcrete, it is important to ensure that during and after the fire event the ground support is designed/predicted not to pose risks to the tunnel occupant. The global behavior of the ground support can be predicted using finite element analysis, and its resistance is derived with consideration of the material strength degradation due to the elevated temperature.

Dec 1, 2022

By Kwame Awuah-Ofei, Sisi Que, Shaochun Yuan, Yumin Wang, Ziwei Ding

This research sought to facilitate improved stakeholder analysis in mining by providing further insights into the preferences of local community members using discrete choice theory. While recent research has demonstrated the usefulness of discrete choice theory in mining stakeholder analysis, no previous work has examined which discrete choice model (DCM) is most suitable. This paper provides a research note on a case study in a mining community that was performed to compare three DCMs. After a thorough examination of the benefits and deficiencies of all models, this study concludes that the conditional logit model stratified by questions is the most useful DCM for mining stakeholder analysis. The recommendation is based on the usefulness and accuracy (ability to match the survey data) of this model.

Jul 25, 2022

By Basak Anameric

This study reports preliminary feasibility investigations for utilization of the selective carbothermic reduction and smelting (SCRS) processing scheme to beneficiate low-grade iron-manganese (Fe-Mn) mineral deposits from MN, USA. The study includes laboratory-scale demonstrations using an induction furnace and production of various products by manipulation of operational parameters. The products include alternative iron (Alt Fe), high carbon ferromanganese (HC FeMn), alternative silicomanganese (Alt SiMn), and upgraded manganese concentrate (Mn conc). All of these products have commercial value and can be used in various applications as raw materials.

Nov 23, 2020

By Yiming Zhang, Yunpeng Li, Chun Feng, Ruyang Cao

In the past, the selection of the number of empty holes between blast holes heavily relied on the subjective experience of practitioners, leading to unsatisfactory blasting results. The number of empty holes between blast holes is particularly important for the perforation of explosive cracks. In order to determine the optimum number of empty holes for inducing the propagation of explosive cracks, a two-dimensional numerical model of two-hole blasting was established based on the continuous-discontinuous element method (CDEM) using polymethyl methacrylate (PMMA) as the medium, and numerical simulation of various working conditions was conducted; the simulation results are basically consistent with the PMMA model test. Through the analysis of blasting parameters, the optimal number of empty holes with a certain hole spacing is fitted. The following conclusions are drawn: (1) There is a threshold for variable x. When x exceeds 50, the presence of empty holes cannot lead to the perforation of explosive cracks between the blast holes. (2) When x is below 50, the optimal number of empty holes inducing the propagation of explosive cracks can be determined through fitting an empirical formula. By adjusting the number of empty holes between blast holes, a significant spacing between adjacent blast holes was achieved, allowing for effective penetration, so as to effectively “induce” the direction of the fracture zone and make full use of the energy of explosives. The research results of this paper are conducive to the research of directional blasting technology and provide certain references for the optimization of precision blasting parameters.

Dec 19, 2023

By W. R. Reed, G. W. Luxbacher

As directed by the MINER act of 2006, the NIOSH Office of Mine Health & Safety Research (OMSHR) has annually awarded contracts to enhance mine safety and health. OMSHR has a history of research that focuses on both respirable coal mine dust and respirable crystalline silica (or quartz) dust, and contracts have been awarded since 2010 in support of our intramural research efforts. In 2018, a National Academies of Science consensus study report recommended expansion of respirable dust research. As a result, beginning in 2018 through 2021, eighteen contracts were awarded focusing on this area. These contracts can be grouped in three topic areas: characterization of coal/dust, development of real time monitors, and improvement of respirable dust controls. This paper summarizes the outcomes of completed contracts and the progress of current contracts.

Mar 2, 2022

By Luttrell. G.

The profitability of coal mining operations is highly dependent on the performance of the coal blending and processing facilities. Many companies have recognized this fact and have instituted optimization programs that require large amounts of coal characterization data, extensive operational information and complex costing models. Unfortunately, this brute force approach to optimization is often overwhelming in terms of time and cost and is generally too inaccurate to be of value in day-to-day field operations. A simpler and more practical approach involves the use of ?micro-price? optimization throughout the coal supply chain. This fundamental concept assigns unit values to each type product (particle or groups of particles) passing through the production units. True optimization occurs whenever all particles with positive worth are recovered and passed to market, while all particles with negative worth are rejected. This paper describes the fundamental workings of the micro-price concept as applied to coal blending and processing operations. Several examples are also included to demonstrate the economic gains that can be realized via the application of this concept.

Feb 23, 2014

By I. Duckworth

P.T. Freeport Indonesia operates a mining complex located in the highlands of Papua, Indonesia. This district consists of underground and surface operations. The East Ertsberg skarn system (EESS) is one of the major orebodies in this district. Subsurface caving of the EESS has been carried out in a systematic series of mining lifts dating back almost 30 years. Present production from the third lift deep ore zone (DOZ), has reached 80 kt/d (88,000 stpd) during 2010, with this rate sustained through 2015. The orebody was proven below the existing caving level, with the next vertical block called the deep mill level zone (DMLZ).

Jan 1, 2010

Lignite is a kind of easy-to-slime and low rank coal. It is hard to be separated by the conventional wet coal beneficiation technologies. Meanwhile, in recent decades, a large amount of fine coal (-6 mm) is generated as the mechanized mining technology has been progressively deployed in coal sector, which causes a great difficult for lignite beneficiation and upgrading due to lack of efficient technology available. In this paper, a vibrated gas-fluidized bed was used to separate the -6 mm fine lignite particles. Separation experiments of -6+3 mm and -3+1 mm lignite were carried out in a laboratory-scale vibrated gas-fluidized bed. The effects of several parameters including the superficial air velocity, vibration intensity, bed height and exterior moisture content on the separation performance were experimentally studied. The results show that the optimal separation performance was achieved when the superficial air velocity is 0.3, the vibration intensity is 1.4, the bed height is 50 mm, the exterior moisture content is below 4% (-6+3 mm) and 2% (-3+1 mm). And the probably error E values of -6+3 mm and -3+1 mm size fraction of lignite are 0.202 and 0.225 respectively. The results indicate that a vibrated gas-fluidized bed can provide an effective solution for -6 mm lignite separation.

Feb 23, 2014

By Abdelaziz Baçaoui, Imane Aarab, Mohammed Derqaoui, Abdelrani Yaacoubi, Khalid El Amari, Abdelmoughit Abidi, Abderahman Etahiri

Numerous researchers have addressed the complexity of the direct flotation separation of apatite from low-grade phosphate ore. The majority of these studies were limited to the micro-flotation scale. In fact, there is no warranty that a reagent scheme that showed a direct flotation of apatite at a micro-flotation scale on pure minerals would automatically replicate the same expected results on the natural ore in the mechanical flotation cell and so was the case for the phosphate ore studied. The overall trend was concentrating apatite in the non-float product. This study aspired to thoroughly assess the flotation performance of this never-exploited low-grade sedimentary phosphate using design of experiments (DOE). Unveiling new insights on such a strategy twist, various parameters and operating conditions, namely, desliming, type of collector and depressant, reagents dosages, conditioning times, flotation time, and pH, were addressed by multiple-factor screening using asymmetrical fractional factorial design followed by statistical interpretations. The collectors tested were the sodium oleate and a fatty acid mixture (FAM). The depressants tested were sodium alginate (NaAL), corn starch, carboxymethylcellulose (CMC), and sodium silicate. The results of the multivariable analysis revealed that desliming, pH, collector dosage, and flotation time significantly influenced the flotation process. Desliming was beneficial for the yield, P2O5 recovery, and SiO2 removal; however, there was still a compromise between grade and recovery. A strongly alkaline pH value of 12 stood out from the whole range. P2O5, CO2, and SiO2 grades of the products and flotation recoveries were improved, except for P2O5 recovery, which was negatively affected. A collector dosage between 2000 and 3000 g/t increased the P2O5 grade and reduced CO2 grade and recovery, enhancing the apatite/carbonates separation. A flotation time of 15 min was significant for P2O5 grade and CO2 recovery, nevertheless, at the expense of yield and P2O5 recovery. The products having initial concentrates of 28.08% P2O5 with a recovery of 88.96% and 29.41% P2O5 with a recovery of 62.71% were obtained using 25 g/t of NaAL and 2000 g/t of the collector FAM and sodium oleate, respectively, at pH 12.

Jun 5, 2022

By Ahmad Rahbar-Kelishami, Zahra Karimi

When alumina is extracted from bauxite ore, one of the environmental pollutants created is known as red mud (RM). This study clarifies that the RM obtained from the Iran Alumina Company has a significant proportion of iron oxides (24%), alumina (19%), silica (17%), and calcium (21%), as well as trace amounts of other minerals. The elements in the RM can be removed and utilized again to reduce environmental pollution. Acid leaching is one of the best ways to selectively exclude some minerals from the RM. In this research, the RM is exposed to different inorganic acids, including HCl, HNO3, H2SO4, and H3PO4, and their binary mixtures. By comparing the results obtained from XRD, EDX, and SEM, it was discovered that CaSO4 crystals are formed by exposing the RM to sulfuric acid. Besides, phosphoric acid was only able to destroy the surface of RM particles. The XRD analyses of acid-washed residues demonstrated that except for the residue of HCl 5 N, all residues contain hematite, showing that inorganic acids cannot easily extract hematite from the complex phases of red mud. While the dissolution of RM with HCl or HNO3 will remove most of the calcium content of RM texture, increasing its iron oxide percentage, which may subsequently be utilized to make colors and pigments.

Mar 29, 2024

By Alafara A. Baba, Yakubu A. Dallatu, Kehinde I. Omoniyi, Shemang Y. Chindo, Edith B. Agbaji

As a result of the rise in global demand for pure copper, there is urgent need to consider the processing of low-grade chalcopyrite ores. Ammoniacal leaching solutions have been reported as an effective and efficient leachant for the dissolution of chalcopyrite. This work reports different parameters that influence the leaching kinetics of a Nigerian chalcopyrite-rich siderite ore obtained from Wase Local Government Area, Plateau State, Nigeria, and assayed as 11.30 wt% of Cu. At the optimum leaching conditions (0.4 mol/L NH3-( NH4)2SO4 leachant concentration; 75 °C reaction temperature; 45 μm particle size), the extent of chalcopyrite ore dissolution reached 87.4% within 120 min. The dissolution rate was affirmed to conform to the diffusion control mechanism with the activation energy, Ea, of 38.84 kJ/mol and a reaction order of 0.661 for the leachant concentration being established. The leaching mechanism was affirmed by characterizing the raw ore and the leached product by XRD and SEM-EDS analysis. Ascertaining optimal leaching conditions for copper using alkaline leachant is advantageous from the environment and economic points of view.

Jan 6, 2023

By James C. Hower, B. K. Parekh

Introduction The purpose of coal preparation is to improve the quality of coal to make it suitable for a specific purpose by (1) cleaning to remove inorganic impurities; (2) sizing-crushing or screening, or both; and (3) special treatment, such as dedusting. The properties and quantities of impurities in coal are of major importance in the design and operation of steam generating equipment. Although boilers are often designed and equipped to use a wide range of coals, no boiler will perform equally well with all types of coals. All coals have certain properties that place limitations on their most advantageous use. These limitations are especially stringent for many of the older installations. Because of a general lowering of quality of raw coal in recent years, the need for coal cleaning has significantly increased. Among the factors contributing to the need for increased coal preparation are (1) increased demand for quality brought on by market and environmental requirements; (2) increased extraneous dilution caused by mine, health, and safety laws; and (3) depletion of the higher-quality coal seams. The major characteristics of coal and impurities from the standpoint of mechanical cleaning are particle size composition, generally called size consist; density differences; the relative friability of the coal and its associated impurities; hardness; and strength. Some of the other factors related to preparation are petrographic composition and rank. RANK CLASSIFICATION Coal is a general designation for a great number of solid organic minerals with different compositions and properties; all are rather rich in carbon and have a dark color, generally black. Next to mineral oil and kerogen, coal is the most important reservoir of carbon in the world. Carbon is an indispensable necessity of life as well as the main source of energy. Coals are found in stratified deposits, sometimes at great depths. All coals owe their origins to slow decomposition and chemical conversion of immense masses of organic material. As found in seams, coal is a heterogeneous mixture of organic and inorganic materials. Not only are there large differences in the properties of coal originating from different seams, but also in coal removed from different locations in a single seam. A genetic relationship exists between peats, brown coals, lignites, biturninous coals, and anthracites. As a whole, the process of coal formation, or coalification, proceeds as a continuous transformation of plant material, each phase characterized by a degree of coalification, or rank. As a measure of this rank, the carbon content or some related parameter can be used.

Jan 1, 1991