Search Documents

By Liaqat Ali Shah, Muhammad Farooq, Zait Ullah Shah, Francisco Rolando Valenzuela-Díaz

Bentonite collected from Nowshera (Pakistan) was treated with NaCl, and the < 2-μm clay fractions were separated by sedimentation process. The textural changes in NaCl treated purified bentonite were compared with raw and physically purified sample. It was detected that the NaCl-treated purified bentonite and the sample purified by simple sedimentation, respectively, consist of sodium-montmorillonite and calcium-montmorillonite as a major clay mineral. The honeycombed-type morphology was observed for both the purified samples; however, the particles of NaCl treated purified bentonite were relatively in a compact form. The particle sizes of both the purified samples were found considerably smaller. The high volume percent of the fine particles was noticed in the NaCl-treated purified bentonite. This attributed that the sodium exchange has a valuable impact on the bentonite dispersion in aqueous media during particle size measurement. The relatively high mesopore area/volume and micropore area/volume and specific surface area (SSA) were detected in purified samples. The NaCl-treated purified sample showed relatively high mesopores area/volume than the sample obtained by simple sedimentation. These changes seem to be originated from either high montmorillonite contents and/or the smaller particle size, which might be produced after the layer rearrangement during the interlayer cation replacement by Na+ ions. The large SSA and high porosity of purified samples particularly the NaCl-treated bentonite suggest their potential use as adsorbents, catalysts, pharmaceuticals, and cosmetics.

Jan 7, 2021

By Mehmet Guney

Acceptable working environments in production areas and service openings of Mindola Mine on the Zambian Copperbelt are currently maintained with an air volume of 1000 cu m/s and 5500 kW of installed refrigeration plant. It is planned to open up additional deeper areas of the mine for future production. Temperature problems, due to the increased heat generation from various underground sources are recognized as potential hinderances to efficient production. Findings of research work indicate that the present total heat output of 58,000 kW will inevitably increase by the second five-year period of the deepening program to 52,900 kW and by the fifth five-year period to 63,200 k\V. Estimated WB and DB temperatures, representing the total heat generation in stope faces and development headings during these same periods are predicted to increase to 53.8/40.2 °C and 35.5/42.1 °C respectively. It is assessed that the nominal refrigeration capacity needs to be progressively increased to 9,000 k\V This paper deals with the thermal problems in Mindola Mine, current heat output calculations, future prediction of temperature and heat load in various working areas of the mine with the application of computer programs and interpretation of data in order to find the effective solution for long-term planning of ventilation and air-conditioning.

Jan 1, 1982

By Robert D. Saltsman

The inadequacy of our knowledge of the coal combustion process has long been recognized. This was expressed very well by Spicer and Finney (1). "The control of combustion processes in industry and the design of the equipment necessary for efficient burning to take place have always been very much branches of an industrial art rather than of an exact science. This has been especially true of the utilization of coal, a substance so hetrogeneous and complex in character that all too little is known about its chemical and physical composition.&apos; During the past several years one branch of coal utilization, that of high temperature carbonization; has made significant advances from being an art into being an exact science. This has been accomplished by the development of petrographic techniques for identifying, measuring, and determining the thermal properties of the organic materials which affect the carbonization of coal and the correlation of this information with a pre-existing standard of coke quality, the stability index.

Jan 1, 1964

By B. P. Sullivan

This paper describes how the author projected the economic benefits of a proposed coal liquefaction project based in Pennsylvania. These benefits were assessed in a successful effort to garner government support for the project. The projections considered such issues as increases in employment, wages, and tax receipts to state and local government, plus other less-obvious benefits, such as site remediation. The paper explains how sponsors of similar projects can use economic projections in making meaningful and compelling presentations to federal, state and local authorities.

Jan 1, 2000

By M. P. Roy, P. K. Singh, A. K. Mishra, Ashish K. Vishwakarma, Vivek K. Himanshu

Ground vibration is one of the major hazards produced by rock-blasting operation. The accurate prediction of vibration is necessary for designing controlled blasting parameters. The existing vibration predictors consider maximum explosive charge weight per delay and distance as the parameters responsible for ground vibration. These predictors are based on the assumption that the geometrical parameters of the blast will be constant for a site. However, the mining sites with bigger production targets have varying geometrical parameters to suit the excavator utility. Accordingly, the other blast design parameters will also have an impact on ground vibration intensity. A principal component analysis is a dimension reduction technique. This technique along with multivariate logarithmic regression has been used in this paper to predict the ground vibration. The technique has classified the blast design parameters into four principal components. The regression with the scores from these principal components has been carried out. The evaluation of the model performance of predictors along with the existing empirical predictors has been carried out using R2 and RMSE values. The evaluation suggests that the predictor with logarithmic regression followed by principal component analysis gives better performance with respect to the existing empirical predictors.

Jul 30, 2022

By Muhammad I. Kabir

The streamline method of recovery prediction reduces a two-dimensional problem to a bundle of one-dimensional ones. This paper presents the development and application of a novel scaling technique which, when used with a streamline model, causes s bundle of one-dimensional problems to further reduce to a single one-dimensional calculation. The one-dimensional calculation accounts for chemical-rock interactions and the streamline model for areal sweep. The scaling technique significantly reduces computation time, is readily modified to desk-top calculations, and can be applied to both absorbing and reacting species. The work was sponsored by the Interior Department&apos;s Bureau of Mines.

Jan 1, 1984

By George H. K. Schenck

The North American-based mining engineer needs to understand the differences that exist between mechanical mining or boring machines built on this continent and those built in Europe. The differences Ere most clearly seen when machines for large-sized openings--about 15 feet high-are considered. This report will focus on the innovations of European origin. The rock-breaking tool, drag bit, or roller cone that is efficient for a particular project is related directly to the strength of the rock involved. This strength is generally stated in reference to the rock&apos;s unconfined compressivee strength in pounds per square inch (psi) although it is well recognized that a rock&apos;s shear strength is also important. Compressive strength has been adopted because it is simple to test for and provides a convenient comparison. Table 1 relates cutter type to compressive strength and indicates the general nature of the machine innovation devel¬oped in Europe.

Jan 1, 1970

By C. J. Bise, M. F. Sindelar

Regulations, such as the MINER Act of 2006, require the installation of redundant and secondary communication systems to assure that contact can be established with coal miners who may become trapped underground as a result of an event such as a fire, explosion or inundation. For half a century, the orientation towards underground communications has been that more complex systems better serve the coal miner. However, if a goal is to provide for an alternative means of establishing communication between the surface and trapped miners underground, then some of the technology employed should be simple, reliable and cost-effective. Coal mines spend hundreds of thousands of dollars on exploratory drillholes to characterize reserves, sometimes decades ahead of mine development. During the pre-mine planning phases, certain exploratory drillholes could be located and then outfitted with a simple communication link that would remain compatible with the continuing evolution of communication systems. Inexpensive links, whose locations would be accurately recorded, would be exposed by continuous miners during mine entry development, thereby allowing an underground phone to be connected to a surface station in the event of an emergency. A latent network of these communication links could be installed for less than $500 each, minimally affecting drilling and grouting operations, and could be designed to be compatible with many communication devices. This research examines methods and materials for incorporating an embedded communication link during pre-mine exploration drilling, addresses significant factors affecting its implementation, and presents a recommended design. Since mine plans are known to change, the objective is to minimize cost so that, if not used, the investment is minimal for a potential secondary means of communication between the surface and underground workings.

Jan 1, 2014

By R. Gilges

The implementation of effective techniques for meeting the maintenance requirements of the new Utah Copper Division smelter, one of the largest in the Western Hemisphere, is a goal of the smelter management and supervisory personnel. Kennecott&apos;s Metal Mining Division Computing Center has been working with smelter personnel to implement a computer program to provide instantaneous access to equipment specifications, maintenance and cost histories, spare parts, preventive maintenance scheddes, etc. for several hundred pieces of equipment. This information will be available to all smelter personnel via visual display terminals. The system will dramatically reduce the time now spent in search of pertinent information required in effectively performing the maintenance functions. It will also be used to analyze practices, detect trends, prepare budgets, and substantially reduce the paper work normally associated with the running of a large and complex maintenance organization.

Jan 1, 1977

By S. M. Cohen

Roll crushers had been used in the past ahead of existing milling systems in order to obtain additional production from such mills in both the mining and the cement industries. Historically, a roll crusher as a preliminator to a ball mill has been used for a number of industrial mineral applications. Flowsheets, from Taggars(1) show systems for fluorspar, graphite, lead and zinc to name a few, which are shown in Figures 1 to 4. These units applied, (in some cases still in service), prior to 1950 and as early as the 1920&apos;s, were of two general types, rigid rolls and spring rolls. The rigid rolls were phased out in favor of the spring rolls. The spring force related to the linear inch width of the rolls, ranged from 500 to 50,000 lbs/linear inch(1) on units up to 90" diameter. With choke feeding, the rolls were spread against the spring force during crushing keeping the system under high pressure to obtain high effectiveness.

Jan 1, 1986

By Jim Clark

Tunnel boring machine (TBM) tunneling is an ever-increasing prospect for underground construction, and, with each new tunnel bored, there are unknown elements. When boring through the earth, even extensive geotechnical baseline reports can miss fault lines, water inflows, squeezing ground, rock bursting and other types of extreme conditions. This article draws on the consider-able field service experience within Robbins to analyze successful methods of dealing with the most challenging conditions encountered. Many tunnel projects are located in areas with relatively poor access along the tunnel alignment and bored under extremely high overburden. These two factors often result in limited geological information. It would be reason-able to state that the deeper the tunnel, the greater the lev-el of uncertainties. When faced with these uncertainties everyone involved with the project including the owner, the contractor and the machine supplier must be prepared to tackle geological surprises. This article describes the problematic geological conditions and associated difficulties faced on three separate projects and the measures that were taken to overcome these difficulties.

By D. C. Torre

Ever since the early &apos;60&apos;s there have been efforts to develop and produce reliable continuous haulage systems capable of taking the full output of a continuous miner and transporting it, in one continuous flow, from the face to the tipple. The majority of the continuous haulage systems which have been most successful to date were placed in operation in the early &apos;70&apos;s and were all of the bridge conveyor type, usually consisting of bridges and mobile bridge carriers attached at the inby end to the continuous miner and at the outby end to the panel conveyor itself. These successful bridge conveyor type continuous haulage systems were, and continue to be, either of the belted or chain type. Undoubtedly, the most successful belt type continuous haulage systems are those manufactured and marketed by the Long-Airdox Company. Until early 1977, the most successful chain conveyor type haulage systems were manufactured and marketed by Jeffrey Mining Machinery Division. In 1977, Long-Airdox reentered the market with a chain type system to complement its belted system. I say "reentered" because the original bridge type continuous haulage system was introduced to the coal mining industry in the early &apos;60&apos;s by the old Long Company, a predecessor of the current Long-Airdox Company, and those original units were of the chain conveyor type.

Jan 1, 1981

By Kraig W. Grubaugh

Rapid growth in the rate of surface mining for coal has caused many states to increase the rigor and complexity of their surface mining codes. The promulgation of Federal surface mining standards may cause those states containing Federal land to amend their codes also. Presented is an up-to-date review of these codes with tabular summaries that divide the codes into operative functions. These summaries will be of use to new operators, multiple-state operators, and state officials. Suggestions are made for industrial efforts to present workable and acceptable amendments to these codes.

Jan 1, 1977

By Danqing Gao, Brijes Mishra

Spatial variance of rock properties is an important characteristic of rock which addresses the heterogeneity of mechanical and physical properties and their effect on underground mining. Assessing spatial variance can be useful for both locating potential difficult grounds and performing reliability analysis in the mining support system. This study shows a microscale numerical model for rock material based on continuum mechanics. To consider the spatial correlation factor of mechanical properties in realistic rock mass, this study introduces a spatial correlation concept into the traditional type III extreme value distribution model. Based on the improved microscale random model, we conducted a series of numerical uniaxial compressive tests and one longwall mine model to investigate the progressive failure of rock. The results show that spatial correlation factor can significantly affect the load-deformation curves and fracture patterns. The spatial variance model was applied to a longwall mine that included several cutting sequences to observe the influence of the spatial variance on roof behavior. The cohesion and friction random fields induced failure that propagated randomly through the immediate roof in different entries. The results showed that the spatial variance provides an accurate prediction of erratic roof falls in coal mines.

Jul 20, 2020

By Reno H. Sales

The syngenetic, metamorphic water, and source bed concept theories of ore deposition proposed by Anton Gray, C, Lo Knight and others, to explain ores in sedimentary rocks, are challenged on the basis of a survey of the literature and personal observation, A hydrothermal origin for the Northern Rhodesian Copperbelt deposits is indicated by the presence of post-Roan age igneous rocks and post-gabbro mineralization, the wide distribution of ore in the various Lower Roan lithologic types, and the zoning of the copper-iron sulphlde minerals and minor elements The proposal by Gray and Knight that igneous rocks are not favorable as guides to nonferrous metal deposits, and Gray&apos;s hypothesis that the redistribution of connate waters and their dissolved metals by metamorphic processes was responsible for the emplacement of ores, are rejected as contrary to field evidence, The absence of exposed potential igneous source rocks is shown to be an invalid argument for the proponents of any syngenetic hypothesis, The common association of ore deposits with calc-alkaline intrusive rocks and their derivatives is, however, demonstrated to be convincing evidence that an exploration program based upon a magmatic theory of origin, would have found most of the important known non-ferrous metal deposits of the world, It is urged that prospecting be continued on the sound basis of accumulated knowledge of the lithologic and structural facts surrounding known ore deposits.

Jan 1, 1960

By Alain S. Kivava, Olawale K. Aromolaran, Charles Nzolang, Anthony T. Bolarinwa, Georges M. Kasay

Rare earth elements (REEs) are crucial in high-tech and green technologies. The Democratic Republic of Congo (DRC), rich in mineral resources, shows potential for REE deposits in carbonatites, pegmatites, and placers. This paper reviews global REE resources, highlights potential REE targets in Africa, and emphasizes the need for further research and exploration in the DRC to unlock its REE potential.

Feb 4, 2022

By C. Feng, W. Song, B. Moudgil, P. Zhang, W. Xiao

Separation of dolomite from phosphate is the most challenging problem in phosphate mineral processing. Over 50% of the future phosphate reserves in Florida contains too much dolomite to process using the current industry practice. The FIPR Institute has collaborated with worldwide experts in the field to address this issue. As a result, the industry is now offered with three feasible options. Optional 1 involves crushing and grinding of high-dolomite phosphate pebbles followed by dolomite flotation at slightly acidic pH using a new collector that does not require phosphoric acid as a phosphate depressant, achieving a final concentrate analyzing less than 0.9% MgO at about 87% P2O5 recovery. Option 2 offers three methods for reducing MgO content in the concentrate from the Crago process, including adding a dolomite depressant in the rougher flotation step, dolomite flotation of the cleaner concentrate, and scrubbing the cleaner concentrate in quartz sand. These methods could reduce MgO content in the final concentrate by 20-40%. Option 3 is a gravity separation technique using an innovative separation jig, and may well be the ultimate solution to the problem. INTRODUCTION Magnitude of the Dolomite Problem With the depletion of the higher grade, easy-to-process Bone Valley deposits, the central Florida phosphate industry has moved into the lower grade, more contaminated ore bodies from the Southern Extension. The phosphate deposits in the Southern Extension may be divided into two zones: an upper zone and a lower zone. The upper zone is readily processable using the current technology, but the lower zone is highly contaminated by dolomite. Geological and mineralogical statistics (Hassan and Bogan, 1994) show (Table 1) that more than 50% of the phosphate resource would be wasted if the lower zone is bypassed in mining, and about 13% of the resource would be wasted if the dolomitic pebbles in the lower zone were discarded.

Jan 1, 2019

By G. Deschênes

In Part I of the work, gold and silver were shown to be efficiently extracted from Kupol samples using lead nitrate in a cyanide leach system. In Part II, a comparison of the technical and economic merits of a new technology called CELP (CANMET Enhanced Leaching Process) was made with the cyanidation/AVR(Acidification-Volatilization-Recycling) process using 8 metallurgical variability samples as well as a large composite sample which represented initial two years of Kupol mill feed. The composite sample had 33.4 g/t Au and 289 g/t Ag. The metallurgical demonstrated that the CELP produced very similar gold and silver leach extractions compared to the standard Cyanidation /AVR leach conditions at 1/2 the cyanide concentration (1000 ppm NaCN in CELP vs. 2000 ppm for cyanidation/AVR leach conditions). It was estimated that the total cost per ton, were approximately the same for the two technologies (total cost of the CELP with the use of Merrill-Crowe at $46.48/ton, with cyanidation/AVR at $46.13/ton). However, the implementation of the CELP would eliminate a capital expenditure of approximately $5 million. Eight variability samples used to confirm the previous results showed that on average the gold and silver leach extractions with the CELP and the feasibility leach conditions were very similar for gold extractions, but 4.6% higher for silver extractions compared to the conventional cyanidation. The decision was made to remove AVR cyanide recovery from the Kupol flowsheet and implement the CELP at Kupol. The ability to use conventional leach equipment with the CELP and simplify the flowsheet was also a factor, given the remote location of the Kupol Mine.

Jan 1, 2009

By S. S. SHINDE, P. C. JIKAR, N. B. DHOKEY

Mill scale is an oxide waste product of steel mills, containing around 70 percent iron and other allied impurities. In the present context, a dynamic prototype counter-current reactor (CCR) was used for the experimentation and simulation of a particle bed using the discrete element method (DEM). Mill scale was pulverized to ASTM mesh range 140 (106 μm)/+ 270 (53 μm) and oxidized in a CCR to make a single oxide Fe2O3 phase by maintaining the required thermodynamic conditions, such as pure oxygen at 1,100 °C. This oxidized powder was then subjected to a reduction reaction in the CCR, with gas mixture (H2:N2) ratio of 1:4 at 875±5 °C for filling degree, fd , and reactor revolution, ω, ranging from 5.38 to 16.14 percent and 2 to 5 rpm, respectively. A creeping fluid flow condition (Re < 1) and natural heat convection (Gr/Re2 >> 1) were maintained during the solid–gas reaction, and the particle-bed behavior was quantified by Froude number for the optimum operating window. The simulation was validated with the experimental results of reactor reaction product by X-ray diffraction (XRD) and scanning electron microscope (SEM) images.

More than 1,200 professionals from the global tunneling and underground space industries are expected to be on hand for the 2009 Rapid Excavation and Tunneling Conference to be held at Caesars Palace in Las Vegas, NV. The conference, set for June 14-17, is sponsored by the Society for Mining, Metallurgy, & Exploration, Inc. (SME) and the Construction Institute of the American Society of Civil Engineers. The four-day conference will feature more than 100 technical papers in 19 sessions. Two one-day short courses are also planned, as are a pair of field trips. And the show?s exhibit will feature more than 120 of the industry?s leading equipment and service suppliers.

Jan 1, 2009