Search Documents

The 26th international APCOM symposium, hosted by The Pennsylvania State University, was held Sept. 16 to 20, 1996 in University Park, PA. Conducted about every 18 months throughout the world, APCOM symposia focus on the Application of Computers and Operations Research in the Mineral Industry. The APCOM International Council is the governing body of the symposia and determines the symposium’s locations and sponsorships. This group is composed of the nine permanent (voting) members. They include the University of Arizona, Colorado School of Mines, Pennsylvania State University, Society for Mining, Metallurgy and Exploration, Inc., Canadian Institute of Mining, Metallurgy and Petroleum, South African Institute of Mining and Metallurgy, Technical University of Berlin, Institution of Mining and Metallurgy and Australasian Institute of Mining and Metallurgy. The three nonvoting members are Moscow Mining Institute, China Institute of Mining and Rudarski Mining Institute of Slovenia.

Jan 1, 1996

By C. L. Lin

The image-based On-line Particle Size Analyzer (OPSA) system has been developed at the University of Utah to measure particle size distributions under plant conditions where overlapped and segregated particles are being transported on a moving belt conveyor. Evaluation of the OPSA system at several plant sites has been completed. The results show a consistent agreement between the particle size distributions obtained from the OPSA system and those obtained from laboratory screen analysis of belt samples. These results and the stable performance of the OPSA system during the field tests suggest that continuous quality control of crushed products is possible using the OPSA system.

Jan 1, 1999

By Anand Kumar, Debasis Deb, V. N. S. Prasad. M, A. K. Mishra

Shield leg pressure data from all shields and shearer locationwith time stamp from a mechanized longwall face are monitored and recorded in a surface computer. These data contain random noise due to power failure, leakage of legs, bad sensor reading and other maintenance or geo-mechanical problems. An algorithm is developed to detect mining cycle parameters such as setting and final pressures and duration of the cycle from these data for the analysis of periodic roof weighting phenomena. The intensities and persistence of periodic roof weighting are the vital information to the mine management to take judicious decision on longwall operation. The paper presents details of the algorithm which identifies 96% of mining cycles from the noisy data belonging to consecutive 5 months or 410 m of face advancement. Based on this analysis, 2 types of periodic roof weighting phenomena are detected, namely, (i) normal type—having peak intensity of 75 to 90% of yield pressure, interval of occurrences of about 10 to 15 m with persistence of 3 to 4 m and (ii) severe type—peak intensity over 90% of yield pressure, interval of 25 to 40 m with persistence of over 10 m. It is envisaged that these phenomena have direct relationship with main roof thickness, its overhung length and material properties.

Nov 19, 2020

By Kazumasa Taguchi

At the Kakogawa works of Kobe Steel. Ltd., the agglomeration facilities are composed of a pelletizing plant and sintering plant. This aim is to utilize raw materials efficiently and stabilize the raw material resources. Therefore at Kakogawa works, the blast furnaces (BF) have been operated with high pellet ratio and various developments for pellet properties have been achieved to improve the blast furnace performance. These developments include dolomite-fluxed pellets, new-porous pellets and crushed pellets. As a results of these improvements, pellets have achieved almost the same performance as sinter at high temperature regarding properties such as the softening, melting and reduction behaviour. However, some problems on shape have remained to be solved. Spherical pellets flow easily into the center of the furnace and form mixed layers of pellets and cokes. Therefore, in BF operations with these pellets it becomes more difficult to keep proper and stable gas distribution.

Jan 1, 1983

By P. Bissert, M. Klein, L. Yan, D. Yantek, R. Matetic

"U.S. Mine Safety and Health Administration (MSHA) regulations require underground coal mines to use refuge alternatives (RAs) to provide a breathable air environment for 96 hours. One of the main concerns with the use of mobile RAs is heat and humidity buildup inside the RA. The accumulation of heat and humidity can result in miners suffering heat stress or even death. MSHA regulations require that the apparent temperature in an occupied RA not exceed 95 °F. To investigate this, the U.S. National Institute for Occupational Safety and Health (NIOSH) conducted testing on a 23-person tent-type RA in its Experimental Mine in a test area that was isolated from the mine ventilation system. The test results showed that the average measured air temperature within the RA increased by 9.4 °C (17 °F) and the relative humidity approached 94 percent at the end of a 96-hour test. The test results were used to benchmark a thermal simulation model of the tested RA. The validated thermal simulation model predicted the volume-weighted average air temperature inside the RA tent at the end of 96 hours to within 0.06 °C (0.1 °F) of the average measured air temperature. IntroductionIf an accident occurs in an underground coal mine, miners who fail to escape from the mine can enter a refuge alternative (RA) for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the potentially adverse thermal environment inside an RA from the metabolic heat of the occupants and the heat released by the carbon dioxide (CO2) scrubbing system. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration, and from the chemical reaction within the CO2 scrubbing system. The accumulation of heat and humidity can result in miners suffering heat stress, heat stroke or even death."

Sep 1, 2016

By D. Blackwell, W. R. Reed, G. Ross, S. Peters, M. Shahan

Dust collectors for roof bolting machines generally use a dry box to collect the roof bolting material. Recently, an underground mining operation converted a dry box dust collector to a wet box dust collector with a unique exception from MSHA for testing purposes. Water is routed to the roof bolter from the main water line of the continuous miner. The wet box utilizes a water spray to wet the incoming material. Testing was conducted comparing the two different collector types. Respirable dust concentrations surrounding the roof bolter with the different collection boxes were similar. The main difference in respirable dust concentrations occurred when cleaning the dust boxes. The average respirable dust concentration during cleaning of the wet box was 0.475 mg/m3, and during the cleaning of the dry box the average respirable dust concentration was 1.188 mg/m3. The silica content of the roof material was high, ranging from 28.9% to 52.7% during this study. The results from this study indicate that using the wet box as a collector reduced exposure to respirable dust up to 60%when cleaning the collector boxes. INTRODUCTION Currently, the dry vacuum dust collection system is the standard dust collector on roof bolters in underground coal mining. It has been proven to be an effective dust control to prevent roof bolter operators’ overexposure to coal mine respirable silica dust during roof bolting operations [Potts eta l, 2011 and Colinet, 2013]. The dry collection system works as follows: drill cuttings are vacuumed into the precleaner. The precleaner dumps oversized material onto the mine floor while undersized material enters the dust box via vacuum airflow produced by a blower. The cuttings entering the dust box are either deposited on the floor of the dust box or into a dust collector bag. The vacuum airflow leaves the dust box through a final filter which removes any small particles from the airflow. Figure 1 shows the internal view of two dry collection system boxes; one that does not use the dust collector bags and another that uses the dust collector bags. Dust collectors that use dust collector bags to contain material inside the dust collector box have been shown to provide better protection to roof bolter operators than dust collectors that do not use the bags [Listak and Beck 2008]. The dry collectors are very efficient at reducing respirable coal mine dust exposure from roof bolting activities. Recently, Blue Mountain Energy’s Deserado underground coal mining operation, outside Rangely, CO, made a modification to the dry collector system to convert it to a wet collector system with a unique exception from the Mine Safety and Health Administration (MSHA) for testing purposes. The wet collector system still uses a vacuum system to pull material from the vertical roof bolt hole, but incorporates a water spray nozzle located inside the dust box to wet the incoming material. The flow through the nozzle ranges from 1.9–7.6 lpm (0.5–2.0 gpm) at 0.69 MPa (100 psi). The conversion to the wet collector system removes the precleaner and the cyclones inside the dust box. The wet material (sludge) then empties through a specialized valve in the bottom of the box. The final filter is still used to prevent respirable dust from leaving the dust box through the exhaust. During operation, the wet collector dust box is opened and hosed clean after roof bolting every place. After every two entries the final filter is changed out. Figure 2 shows the inside of the wet collector box.

Jan 1, 2019

By Jianbo Hu, Gang Han, Tao Zheng, Junfeng Jiang, Rui Su, Qihua Zhao

The rock quality designation (RQD) is a commonly used index for the classification and evaluation of rock mass quality and is widely adopted in mining and geological engineering. The traditional method of obtaining RQD still requires manual measurement of core length and calculation of RQD, which is inefficient. To address this problem, we propose a framework for drilling core image segmentation and RQD estimation from digital images of cores in core boxes based on the deep learning algorithm. The proposed framework is generated by combining the Mask Region-Based Convolutional Neural Networks (Mask R-CNN) instance segmentation algorithm, the U-Shaped Convolutional Neural Networks (U-Net) semantic segmentation algorithm, and the image processing functions of the Open Source Computer Vision Library (OpenCV). To demonstrate the accuracy of the proposed method, seven boreholes in the Xiushuihe vanadium-titanium magnetite mine, located in the Sichuan Province, China, were used as the case study. According to the comparison of the manual measurements and calculations of the cores taken from seven boreholes used to conduct this study, the framework can record the length of the drill cores and calculate RQD within an average error rate of 3.42%, while it saves about 85% of the working time. The results illustrate that the proposed framework enhances the efficiency of RQD calculation while satisfying the engineering requirements.

Jul 31, 2023

By Patrizia Pereyra, M. Guzman, C. Toledo, J. A. Rau, A. Ruiz

The use of mining tailings-based geopolymer binder as a substitute for cement can be an interesting alternative to the problem of final disposing of large volumes of them. Indeed, mining tailings have a high silica content, which makes them suitable for geopolymerization. The tailings samples contain Cu, Pb, Zn, As, Sb, Cd and Bi, mainly. X-ray diffraction results show that the tailings are composed of quartz, SiO2 (81%). Geopolymerized tailing samples (GTPS) were obtained by varying the ratio of SiO2/ Al2O3 and SiO2/NaOH. The compressive strength of the GTPS varied between 2 MPa and 8 MPa. The electrical conductivity in the leaching tests varies between 13.91– 16.11 mS/cm2 indicating that ions are present in the solution. However, the pH = 10.5 indicates that acidity is not being generated. The element that mostly leaches is iron. The highest percentage of leaching is observed for cadmium (69%) and chromium (93%). The concentrations of elements are under the maximum permissible limits for water according to the Peruvian legislation. However, mass transfer leach tests and immersion leach tests must be realized.

Feb 1, 2024

By F. Djahanguiri

The U.S. Bureau of Mines is conducting research on underground stope leaching of metalliferous ores to minimize the environmental impact of ore processing on the surface and to maximize minable reserves. An aspect of this research is to minimize pregnant solution losses and/or groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope leaching economics. A reinforced concrete bulkhead was designed, constructed, and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead design methodology and construction procedure.

Jan 1, 1995

By Éder Domingos Oliveira, Leandro Viana Teixeira, Carlos Antonio Morais, Ruberlan Gomes Silva

The purity of rare earth products depends on the ability of the reagents used to selectively promote the precipitation of the rare earth elements (REE) from impurities present in sulfuric liquors. The present study aims at investigating the conditions required to precipitate REE, either as rare earth oxalates or carbonates, from purified rare earth sulfuric liquor with a low Al3+ and UO2 2+ and a very high Ca2+, Mg2+, Mn2+, and SO4 2− impurity content. The rare earth sulfuric liquor was obtained in a previous study by the reaction of a rare earth ore with sulfuric acid, pyrolysis at 700 °C/2 h, cooling at 20 °C, and water leaching. The impurities such as Fe3+, Th4+, and PO4 3− were completely removed from the liquor in two consecutive neutralization steps. In order to recover the REE, the purified rare earth liquor was then treated with oxalic acid and sodium carbonate. Rare earth oxides (REO) precipitated with oxalic acid displayed a very high purity (99.2% w/w) and low impurity content. In contrast, the rare earth carbonates precipitated with sodium carbonate presented a comparatively lower REO content (68.5% w/w) and 94.2% of purity, but with a higher content of impurities. Better precipitating conditions were achieved at 60 °C, compared with 20 °C, and under stoichiometric reagent consumption, with REE precipitation efficiencies higher than 96%. The dosage above the stoichiometric condition caused the precipitation of calcium oxalates and co-precipitation of rare earth sulfates when oxalic acid is used, and precipitation of calcium, manganese, and uranium carbonates and also a co-precipitation of rare earth sulfate when sodium carbonate were used. An integrated flowsheet to produce a high-quality rare earth product from rare earth sulfuric liquor containing some impurities is proposed.

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

Dumper operators are frequently exposed to whole body vibration (WBV) in surface mines. Surface mining activities involve the amalgamation of comparatively high intensity of vibration and extended exposure durations. Efficient risk reduction mandates knowing of important phases of a task that poses a threat to health of dumper operators. So far in India very limited studies have been reported on WBV exposure with regard to surface mines. This paper evaluates WBV of dumper operators based on ISO 2631-1:1997 Standards and European Union (EU) Directive 2002 for different phases of job cycle. Six dumpers were considered for this study and the vibration measurements were made for all the four phases of the job cycle by placing the triaxial accelerometer on the operator’s seat-surface and at the seat-back, independently. The findings of the study revealed that the haulage task (loaded travel and empty travel) remains the chief contributor to vibration exposure according to seat-surface and seat-back measurements. Maximum frequency weighted root mean square (RMS) of 1.12 m/s2 and 1.09 m/s2 were reported for empty travel task for seat-surface and seat-back measurements, respectively. For seat-surface measurements based on RMS, Z axis remains as the dominant axis of vibration for all the dumpers during haulage task, whereas for seat-back measurements, the dominant axis varies between X and Y. Exposure action value (EAV) based on RMS has exceeded the threshold value of 0.5 m/s2 for all the dumpers during loaded travel and empty travel for seat-surface as well as for seat-back measurements.

By S. Potgieter-Vermaak, T. T. Chiweshe, W. Purcell

Complete isolation of chromium (III) from the reference material (SARM 131), Upper Group 2 (UG2) chromite ore, and Merensky Reef mineral ore was achieved using ammonium phosphate salt as flux. Optimum pH (3.2–3.8) conditions and sample to flux ratios (1:25) were some of the factors that were critical for the complete isolation of chromium. Increasing the sample to flux ratio (1:50 excess) however resulted in the conversion of all the elements in the melt into a green solution (pH, 5.8–6.7). A different chromium compound was subsequently isolated from the green solution by allowing this solution to stand in an open vessel in a cupboard for a month during which time the pH decreased to pH 3.5–4.2. Quantitative analyses of chromium from the isolated precipitates of SARM 131, UG2 chromite ore, and Merensky Reef mineral ore indicated chromium contents of 41.87, 60.41, and 23.93% respectively which were very close to the chromium content in the original samples. Analysis of the chromium precipitates using IR indicated the presence of phosphates (1100–1200 cm−1 ) while SEM-EDX analysis showed the presence of microscopic crystalline particles with Cr, P, and O as the major elements. Further characterization of the chromium precipitates using XRD and Raman successfully identified the product as chromium (III) metaphosphate C-type (Cr(PO3)3, JCPDS no. 01-077-0672), in the isolated chromium precipitates.

By Igor Gonzales G.

The Southern Peru Copper Corp. (SPCC) recently built an integrated copper project consisting of dump- and heap-leaching operations at its mine complex in Peru. The pregnant leach solution (PLS) containing the solubilized copper from the leaching operations is processed in a new solvent extraction/electrowinning (SX/EW) facility to produce high-purity cathode copper. The dump leaching and SX/EW facilities are located near the Toquepala mine site. The crushing and heap-leaching operation is located at the Cuajone Mine. The pregnant leach solution from Toquepala and Cuajone is pumped 35 km (22 miles) to the SX/EW plant at Toquepala. The SX/EW plant consists of three trains of solvent extraction (SX), a tank farm area and an electrowinning (EW) facility. The solvent extraction plant has a total PLS flow capacity of 3,210 m3/hr (113,360 cu ft/hr). The electrowinning facility has an expected long-term production capacity of 97 t/d(107 stpd) or about 35 kt/a (38,500 stpy) of cathode copper. However, present production exceeds the expected long-term by about 20%.

Jan 1, 1996

By Joseph B. Alberts, David D. DiPonio, Francis B. Manning

From 1996 to 2001, Wayne County and 13 suburban Detroit communities constructed the Downriver Regional Storage and Transport System (DRSTS) to improve area water quality, protect public health and alleviate basement flooding. The project consisted of a 10-mile long storage and transport tunnel, a pump station at the existing wastewater treatment plant, 9 miles of relief sewers (6 in tunnel and 3 in open cut). The work was separated into 10 contracts. Due to hydraulic design requirements and other constraints, the tunnel profile was located generally 65 feet below ground surface within a soft to medium clay strata which skimmed along the top of a very dense glacial till “hardpan” overlaying bedrock. Boulders within the tunnel bore were recognized as a significant, but indeterminate risk. This paper presents a case history of the owner’s contracting strategy for risk assumption and management of the boulder impacts on the project. Actual conditions encountered during construction and contractual adjustments made to address problems are reviewed, and recommendations for future contracts are included.

Jan 1, 2003

By NEHA PANDEY, Sunil Kumar Tripathy, ARIJIT BISWAS

Due to the growing market of Electric Vehicles (EVs), there is a rise in battery demand. Nickel can be used as a potential element in cathode for lithium-ion batteries. Nickel can provide thermal stability, high energy density, and conductivity in cathodes of lithium-ion batteries. Low-grade chromite overburden from Sukinda mines contains less than 1 wt% of nickel, which can be utilized to extract nickel. Recovery of nickel from such low-grade overburden can help in value addition. The present study provides deeper insight into the aspects of extraction of nickel product derivatives (NPDs), mainly mixed hydroxide product (MHP), through the hydrometallurgical route. The current study focuses on extracting nickel and cobalt from a mine overburden with 0.41% nickel with major silicate gangue. MHP can be processed further for nickel sulfate production, a potential raw material for cathodes in EV batteries. The study discusses a process flowsheet to recover nickel and cobalt from overburden through atmospheric leaching with pre-calcination. It is observed that the step of pre-calcination improves the effective recovery of nickel from overburden. The leaching reactions are effective at a temperature of 90 °C and 1 atmosphere pressure. The orthophosphoric acid was used as a lixiviant for the selective recovery of nickel and cobalt from overburden. Recovery of nickel and cobalt obtained at optimum conditions is 84.0% and 39.9%, respectively. The iron impurity in the leachate solution is 1.27%. It is concluded that the process with pre-calcination along with acid leaching is effective for extracting nickel and cobalt at atmospheric pressure.

Dec 28, 2023

By J. S. Limb

Actual issues which arose during the discovery process or subsequent court testimony are presented. While most of these issues relate to the author’s specialty of mineral appraisal some are more general in nature and could be of interest to those who may be involved in current or future court testimony. Several important areas to be reviewed and agreed upon with the client and their legal counsel are discussed. General observations on litigation, the discovery process, testimony and some repercussion’s are also given.

Jan 1, 2001

By Keith Whiting

The Little Boulder Creek molybdenum deposit is in central Idaho, in the White Cloud Range about 3.2 km (2 miles) northeast of Castle Peak, the highest peak in the range. The elevation of the deposit is about 2591 m (8500 ft). The deposit is accessible only by helicopter or by a 12.9-km (8-mile) trail from the county road along the East Fork of the Salmon River. The nearest towns are Clayton [25.7 km (16 miles) northeast], Stanley [33.8 km (21 miles) northwest], and Ketchum [45 km (28 miles) south-southeast]. The principal known deposit at Little Boulder Creek is called the "North Zone." In this zone, the molybdenite occurs both in stock- work veinlets and disseminated through metamorphosed quartzite of Pennsylvanian age. Pyrite is ubiquitous, averaging perhaps 0.05%. Scheelite and/or powellite are present in trace amounts. An intrusive quartz monzonite stock, probably of Cretaceous age, bounds the deposit on the west. A steep fault which drops Tertiary age Challis volcanics into contact with the mineralization limits the deposit on the east.

Jan 1, 1991

By John T. Bartlett

During the last decade, the increasing price of gold has renewed interest in the various metallurgical techniques for recovering precious metals. Much of the recent technology advance has been aimed at low grade deposits resulting in more complex processes and the necessity of tighter economic control. These factors along with more stringent environmental constraints have made it necessary to optimize each process to minimize energy and raw material consumption and reduce waste discharge. In most cases, detailed process analysis is required to detect inefficiencies and provide alternative solutions for process improvement. Also during this same period, the computer has become widely accepted and computerized mathematical modeling has been applied to an increasingly broader range of problems. Microcomputer based process modeling and simulation systems are routinely used to analyze and improve communition, hydrometallurgical, and pyrometallurgical processes for the recovery of precious metals.

Jan 1, 1987

The Mesquite mine is being operated by Gold Fields Operating Co.-Mesquite, a subsidiary of Gold Fields Mining Corp. The mine Is located in southeastern California about 56 km (35 miles) east of the farming community of Brawley, California. The mine has been in commercial production since early 1986 and Is a conventional open pit mine developed on 6.1 m (20 foot) benches. The gold is recovered by heap leach using permanent heaps built in multiple 6.1 m (20 foot) lifts. This year's gold production will be in the range of 5,600 kg (180,000 troy ounces). Current ore production is about 18,140 tonnes (20,000 tons) per day while the total tons mined Is averaging 65,000 tonnes (72,000 tons) per day. The climate at the mine is extremely arid with rainfall of 7.6 cm (3 inches) per year. From early May until late October daytime temperatures generally exceed 37.8 degrees Celsius (100 degrees Fahrenheit) and can be as high as 37.9 degrees Celsius (120 degrees Fahrenheit).

Jan 1, 1989

By Gülhan Özbayoglu, Yusuf Ziya Akgök

The effect of cooling rate on the flotation behaviour of copper slags of flash smelter plant in Samsun was investigated. Fresh molten slag was solidified in laboratory scale in three different ways. All the samples were characterized by chemical and mineralogical analyses. The chemical analyses showed that samples prepared from fresh slag had 0.9 to 1 % Cu with 40 % Fe and 30 to 32 % SO2. Old pit slag samples contained between 1 to 3% copper. Microphotographs showed that rapidly cooled slags showed fine size distributions, e.g. the copper grains in granulated slag had sizes in 1-2 microns. On the other hand, the size of copper grains in slowly cooled slags increased above 40 microns. Flotation tests carried out by using potassium amyl xanthate and Flotanol-C showed that slowly cooled slag reduced the copper losses in the tailing and improved the grade of concentrate. Under the light of laboratory investigation, the pit dimensions of Samsun Plant have been modified which resulted in a pronounced improvement of the grade and recovery of concentrate produced at Samsun slag flotation circuit.

Jan 1, 1995