Search Documents

By P. T. Bissert, L. Yan, J. R. Srednicki, J. A. Yonkey

"Refuge alternatives (RAs) are required in underground coal mines to support life post-disaster. RAs are mandated by MSHA to maintain an apparent temperature (AT) at or below 95°F (35°C) while providing a safe and livable shelter for a minimum of 96 hours. Because strata composition and mine temperatures will affect the final AT within an occupied RA, NIOSH researchers have collaborated with five underground coal mines across the US to characterize the effects of geographic location and seasonal temperature fluctuations on mine air temperature, relative humidity, and mine strata temperatures. The data collected indicates that some mines will experience greater temperature fluctuations than others, based on geographic location. The mine which demonstrated the greatest temperature differential over the course of the year resulted in a mine air temperature that ranged from 53.4°F (11.9°C) to 84.2°F (29.0°C) and a rib surface temperature that ranged from 55.4°F (13.0°C) to 82.8°F (28.2°C). This data suggests that the location and seasonal peak temperature can significantly affect the mine strata temperature, which could lead to a fully occupied RA exceeding the 95°F (35°C) AT limit over the course of 96 hours. The data reported in this paper could be used to examine the heat buildup inside an RA for actual mine conditions. Thermal simulations could be implemented to evaluate maximum occupancy ratings based on actual mine temperatures and strata compositions. INTRODUCTION In the event of a mine disaster, miners’ primary focus is to escape. Should their attempt be futile, they can enter a refuge alternative (RA) to await rescue. In 2008, the Mine Safety and Health Administration (MSHA) mandated that underground coal mines implement RAs within 1,000 ft (304.8 m) of the working face and spaced within one-hour travel distances in outby areas where persons work such that persons in outby areas are never more than than a 30-minute travel distance from an RA or safe exit. These RAs are required to provide a safe and habitable shelter for a minimum of 96 hours and to prevent the apparent temperature (AT) from exceeding 95°F (35°C) [1]. There is concern throughout the industry that in some cases the internal ambient of occupied RAs may exceed the 95°F (35°C) AT limit due to the potentially hot mine atmosphere as well as the metabolic heat generated by RA occupants and the carbon dioxide scrubbing system. The National Institute for Occupational Safety and Health (NIOSH) has conducted tests in its Safety Research Coal Mine (SRCM) and its Experimental Mine (EM) to investigate heat buildup in RAs. It was found that the number of occupants in an RA may need to be reduced based on the ambient mine temperature, which varies from mine to mine [2]. Further testing and analyses were completed to evaluate the mechanisms (conduction, convection, radiation) by which heat is transferred from an RA to the mine surroundings. Additionally, the effects of varying mine strata compositions on the heat buildup inside an RA were studied [3]. The mine strata temperatures will increase due to heat transfer from within an RA. Depending on the mine strata composition, some mines may be more thermally conductive than others. For example, sandstone is much more conductive than shale or coal (i.e. it disippates heat at a quicker rate). All things being equal, the air temperature inside of an RA after 96 hours will be higher for a mine with strata that has low thermal conductivity compared to a mine with high thermal conductivity."

Jan 1, 2017

By R. W. Smith, D. L. Taylor, K. A. Altman

The importance of metallurgical information in reaching appropriate decisions during the development of mining projects is demonstrated. A financial analysis is calculated using a simulation that includes random number generators. The results are compared to the results of a traditional sensitivity analysis. The traditional analysis is shown to have the potential to overestimate the value of mining projects. The type of statistical distribution selected for the random number generator affects the results significantly. The statistical method of analysis provides insight into the amount of metallurgical testing to be completed and verification of how representative the samples are.

Jan 1, 2000

By X. X. Jiang

An efficient recovery of finely divided magnetite particles of 400/500 mesh from a mixture of magnetite/silica particles has been investigated by imposing a delicate balance between centrifugal and surface tensional forces on these particles. The effect of centrifugal force, surface tensional force, density and size of particles on the overall metallurgical efficiency has been examined. A mathematical model based on a momentum balance on the particles at the liquid/liquid interface has been developed. The validity and limitations of the model are discussed in view of the experimental results obtained.

Jan 1, 1992

By T. W. Camm

Aristotle made the observation that man is a political animal. Engineers often like to think they are above the fray when it comes to organizational politics, but most organizational theorists believe politics is a fundamental dynamic in any group. This paper examines the various ways that people use power within organizations to negotiate the political interactions in the work place.

Feb 27, 2013

By R. R. Kallu

The current 120 psi seal design and evaluation practices are mostly based on simple analytical solutions. Considering the simplistic assumptions and limitations involved in simple analytical solutions and practical difficulties involved in conducting conventional full-scale explosion tests for evaluating 120 psi seal designs, there is a need for developing new scientific methods and engineering practices for design, analysis and evaluation of mine seals.

Jan 1, 2010

By Xianyang Qiu, Xiuzhi Shi, Chen Xie, Xiaofeng Huo, Yanhai Wang

In upwards medium-deep hole cut blasting, many confinement effects exist due to the small number of free surfaces, which is mainly provided by an empty hole. If the cut blasting effect cannot meet expectations, then subsequent blasting construction will be seriously affected, and large security risks to operators in the stope can be induced. The number of free surfaces is directly related to the layout of the cutting borehole. Therefore, it is necessary to optimize the layout of the first round of cutting boreholes. Theoretical analysis, numerical simulations, and field tests were used to study the formation process of cut blasting and optimize the layout of the first round of cutting boreholes. Based on the blasting parameters in the field, LSDYNA software was used to establish cut blasting models with four kinds of borehole layouts in the first round. The RHT constitutive model was used to simulate the rock-breaking effect. The numerical results show that the cut blasting effect is optimal when Nos. 3, 5, 7, and 9 are charge holes and Nos. 1, 2, 4, 6, and 8 are empty holes. In addition, the greater the number of empty holes, the larger the release space and the better the cut blasting effect. The uniformity of the empty hole distribution, namely, the uniformity of the release space, also affects the cut blasting effect. The field results indicate that a good cut blasting effect can be achieved by optimizing the borehole layout.

Sep 7, 2023

By T. Grammatikopoulos, C. Gibson, M. Aghamirian

"Lithium is a soft, silver-white alkali metal with atomic number 3. As of 2015, the end use of lithium was estimated to be as follows: lithium-ion batteries (35 percent), ceramics and glass (32 percent), lubricating greases (9 percent), air treatment (5 percent), continuous casting mould flux powders (5 percent), polymer production (4 percent), primary aluminum production (1 percent) and other uses (9 percent) (Jaskula, 2014). Lithium is found in brine lake deposits containing lithium chloride and in hard rock pegmatite deposits. It can be sold in a range of product types; as mineral concentrate, brine, compound (lithium carbonate or lithium hydroxide) and metal depending on its intended end use (Goonan, 2012; Jaskula 2014).In the 1990s, the United States and Chile were the largest producers of lithium globally, primarily from brine operations (Ober, 1994). Most of the lithium compounds produced during this period were consumed in the glass, ceramics and aluminum industries. In the 1980s and 1990s, there were two major lithium operations in the United States: brine operations at Silver Peak, NV and a spodumene mine and lithium carbonate/lithium hydroxide plant in Kings Mountain, NC. The Kings Mountain operations ceased production in 1991 and were eventually dismantled in 1994. Brine operations were also active in Argentina and Chile, while the largest lithium ore deposit in the world was operated at Greenbushes, Western Australia. During this period, it was predicted that major shifts in demand for lithium would come from the success and widespread use of electric vehicles (Ober, 1994).Lithium is still produced from the brine operations at Silver Peak. But in more recent years, Chile has become the world’s leading producer of lithium carbonate from brines. Australia has maintained its position as the world’s largest producer of lithium mineral concentrate, the majority of which is exported to China to produce lithium carbonate and lithium hydroxide (Jaskula, 2014).A spodumene concentrate was also produced at the Tanco Mine in Manitoba, Canada beginning in the 1980s through to 2010 when lithium operations were suspended due to fluctuations in the lithium market price (Martins et al., 2013)."

Jan 7, 2017

By E. J. Berentsen

The Turquoise Ridge gold deposit is located near the Getchell Mine, 72 km (42 miles)northeast of Winnemucca, NV (Fig. 1). The deposit is owned by Getchell Gold Corp. The host rocks consist of Ordovician and Cambrian age shales and limestones. They have been crosscut by the northeast-trending Turquoise Ridge shear zone and northwest-trending shear zones. Gold mineralization occurs at depths from 427 to 671 m (1,400to 2,200 ft) along the intersection of these structures. Large tonnage, flat-lying deposits occur where folded, favorable beds are intersected by the faults. The carbonate in the beds has been replaced with silica, pyrite and arsenic sulfides.

Jan 1, 1996

By S. D. Thompson

An AIME transaction by P.L. Allsman (1960), "Analysis of Explosive Action in Breaking Rock," contains many useful concepts applicable to blast design. Of special interest was the derivation of a heave blasting burden formula, which is important in establishing the maximum burden. Unfortunately, its derivation contains a fundamental error and then a compensating one. This formula was: [ ] The derivation used the impulse-momentum principle, with a 0.3 m thick (1 ft thick) radius of rock mass being acted on by an explosive impulse. However, the rock weight was not converted to mass by dividing by the gravitational constant. This mistake can be verified by checking the units in the formula, which resolve into m%-sec instead of meters. Adding the gravitational constant corrects this: [ ] If the minimum velocity is now taken as 0.3 m/sec (1 ft per sec), as was recommended, excessively large burdens result. Any appropriate rock velocity should be capable of throwing the rock mass a minimum distance so that the swell needed for breakage can occur. Unless the burden is extremely small and the bench height is very high, it is unlikely that a velocity of only 0.3 m/sec (1 ft per sec) will be sufficient. A review of the literature indicates that average rock velocities observed by camera studies typically range from 15 to 30 m/sec (50 to 100 ft per sec) (duPont deNemours and Co., 1977; Tansey, 1979). On this basis, a minimum rock velocity of about 15 m/sec (49 ft per sec) would be expected and not 0.3 m/sec (1 ft per sec). When a velocity of 15 m/sec (49 ft per sec) is inserted into the corrected formula, the results approximate those of the original formula with a velocity of 0.3 m/sec (1 ft per sec). The errors were approximately self-compensating [ ] References Allsman, P.L., 1960, "Analysis of Explosive Action in Breaking Rock," Transactions, AIME, Vol. 217, pp. 475-476. E. I. duPont deNemours and Co., 1977, Blasters' Handbook, 175th Anniversary Edition, Dupont, Wilmington, DE, pp. 233. Tansey, D.O., 1979, "The DuPont Sequential Blasting System," CIM Bulletin, Vol. 72, July, p. 80. Thompson, S.D., 1981, "Critical Review and Revision of Surface Blasting Practice," MS thesis, West Virginia University, pp. 308-316.

Jan 3, 1985

By Dermot M. Winters, Brent T. Wahlquist, C. Y. Chen

The enactment of the Surface Mining Control and Reclamation Act (SMCRA) in August 1977 addressed subsidence resulting from underground mines, in addition to creating the requirements for reclamation of surface coal mines. Subsidence control regulations pursuant to SMCRA were initially promulgated in March 1979. Several revisions have since been made. In addition, due to court challenges some regulations have been remanded and others are still on appeal. In the meantime the Secretary has agreed to initiate rulemaking on some issues. It is yet to be determined how the prohibition of certain areas from surface coal mining operations under Section 522(e) of the Act applies to subsidence. This presentation discusses the status of the regulations and issues related to or affecting the subsidence regulations.

Jan 1, 1986

By L. M. Litz

In reply to Mr. DeVries comments on my paper, I would like to say that it is true, as pointed out by Mr. DeVries, that under some special conditions, the use of high concentrations of hydrogen peroxide might provide higher short term in-situ …

Jan 1, 1982

By H. Savasci, G. Yarim, J. S. Chung

As part of ongoing deep-ocean mining research, hydraulic transport systems as well as status of deep-ocean mining systems are reviewed in the aspects of manganese nodules and crusts from 8006,000-m depth. The emphasis of the investigation of hydraulic transport is placed on the shape effect of particles on the pressure gradients and flowrates. Series of tests are being conducted to study the lift characteristics of a 2-phasevertically upward hydraulic transport of 2 types of small solid particles in a PVC pipe of 1-in (2.54 cm) diameter: irregular-shaped silica sands and equivalent spherical glass beads. Pressure drops and mass as well asvolumetric flow rates were measured by electromagnetic(EM) flowmeter and mass flowmeter. The particle sizes used are 8-10 mesh. The results in turbulent flow range of 101045Re show that pressure gradients or friction factors are smaller for the spherical beads than the sands. The larger the concentration of the particles are, the larger the pressure gradients become. The larger the particle concentration is, the less the effect of particle shape on pressure gradients becomes. The shape effect is greater for the minimum particle transport velocities than for the settling velocities.

Jan 1, 1999

By G. Myers, C. J. Wendt, W. H. Wilkinson, M. D. Dennis

Precious metal mineralization at Mt. Hamilton, NV is associated with a polymetallic, garnet-pyroxene skarn system developed in middle to upper Cambrian calcareous shale, limestone, and dolomite. The skarn is developed around the Cretaceous Seligman and Monte Cristo calc-alkaline stocks. Gold is associated with intense retrograde alteration. Later epithermal quartz veins contain gold, silver, base-metal sulfides, and sulfosalts cross-cut skarn alteration. Westmont Mining Inc. is currently developing two mineralized zones containing a geologic resource of about 7 Mt (7.7 million st) that averages 1.7 g/t (0.05 oz per st) gold and 17.2 g/t (0.5 oz per st) silver. The project will have an estimated mine life of seven years, with a planned annual production rate of I t (35,000 oz) of gold and 9.3 t (300,000 oz) of silver.

Jan 1, 1990

By C. A. Pryor

The aggregates industry is the largest minerals industry in the United States producing over 2.6 billion metric tons of crushed stone, sand and gravel annually. Approximately 5% of that production is fine material, passing a 75-micron mesh sieve. Of that amount, about 77% is not sold and represents one of the major industry issues. The material accumulates in stockpiles and settling ponds having an operational and economic impact on the site’s bottom line. Many factors cause this material to be produced: from blasting and processing techniques all the way to end use specifications.

Jan 1, 2002

By L. Mead

Dimension stone is a natural stone (granite, marble, limestone, sandstone and slate) that can be quarried, cut and shaped to conform to acceptable industry standards for size, consistency and durability. There are numerous outlets for the finished product in exterior and interior architectural and design applications. A continued growth market is with residential usage— particularly in new, upscale construction. This has become a competitive market between domestic producers and lower cost imported products. These imported products have become available at many of the building supply retail outlets and have increased the use of stone in residential construction and renovation. The traditional architectural application of dimension stone is tied to commercial and institutional building construction trends and market. There has been a noticeable increased usage of stone in the Sun Belt. This stone is usually supplied by local fabricating shops. It is used in the exterior and interior of shopping malls. This market generally uses local stone sources. It has increased the demand for sandstone, limestone and quartzite in this region of the country.

Jan 1, 2005

By Yi Yang, Xiuzhu Su, Wei Sung Ng, Shuiping Zhong, Miao Chen

With over 260 tons of gold reserves, the Shuiyindong gold mine is one of the largest Carlin-type gold deposits in China. A particular challenge in the processing of the ore is the presence of carbonaceous compounds, which can cause substantial losses in recoveries via the preg-robbing and adsorption of gold. To investigate the structural properties of the native carbon and to compare between different characterization techniques for such compounds, pre- and post-flotation mineral samples containing 0.9–4.8% non-carbonate carbon from the Shuiyindong mine have been examined via mineralogical and thermogravimetric approaches, as well as spectroscopic techniques, including X-ray photoelectron spectroscopy (XPS), near-edge X-ray absorption fine edge structure spectroscopy (NEXAFS), solid-state 13C nuclear magnetic resonance (NMR) spectroscopy, diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, Raman spectroscopy and preg-robbing measurements. NEXAFS and DRIFT yielded the most reliable results, indicating that 60–75% of the organic carbon in all samples consist of aliphatic alkenes with substantial unsaturated content, highly similar to activated carbon, with the remainder being graphitic and humic. Speciation by XPS was sub-optimal due to spectral overlaps between graphitic and aliphatic carbon, and between carboxylic and carbonate functionalities, while NMR spectroscopy could not provide reliable speciation of the carbon groups. The preg-robbing strength was strongly correlated to the aliphatic content and structural disorder in the carbon, while no such relationship was found with the graphitic and humic content.

Nov 29, 2021

By M. J. Hrebar

A study was conducted to evaluate the applicability of large wheel loaders (Caterpillar 994 Class) for use as primary loading equipment in open-pit iron-ore operations. Field visits were made to taconite and gold mines that used large wheel loaders. Information was gathered on loader selection rationale; operation and maintenance experience; and production, availability and costs. Brief time studies were conducted to indicate machine performance and utilization. This paper summarizes the field data that was collected, including an economic comparison of wheel loaders and cable shovels in an iron-ore application.

Jan 1, 1998

By A. Karami

It is well established that an ordered sequencing of charge initiations in a blast pattern is an important design consideration that affects blasting performance. Delay times must be chosen such that damage to the rock mass is controlled. The accuracy of delay detonators is also of major concern. A large scatter could lead to an incorrect blast sequencing that would lead to damage to the rock mass causing increased over-break, degraded fragmentation, increased fly-rock and poor vibration control. In this study, the effect of using accurate delay detonators on the explosive energy generated is investigated. For this purpose, power spectral density of the blast vibration for delayed shots are calculated and compared with the case where holes are shot at the same time (no delay). At the end the results are presented and discussed.

Jan 1, 2000

By Qinbo Cao, Qianshan Peng, Heng Zou, Xingcai Yu

In this work, a new flotation strategy was proposed for the flotation of rutile. In this strategy, rutile was activated by Pb(NO3)2 and then floated with amyl xanthate (AX) as a collector at pH 8. Pb(OH)+ was the dominant lead species in the solution at pH 8 and is believed to be the major species reacting with the rutile surface. Time-of-flight secondary ion mass spectrometry (TOF-SIMS) study revealed that the lead activation products were well distributed on the rutile surface, and AX− could further bind with the Pb atom on the Pb-activated rutile surface. In this regard, the Pb-activated rutile could be floated by AX. Furthermore, X-ray photoelectron spectroscopy (XPS) analysis indicated that Pb(OH)2 was generated on the Pb-activated rutile surface. The electron transfer during the adsorption of the AX− on the Pb-activated rutile surface was also investigated by XPS analysis.

By P. A. Plunkert

Metallurgical-grade bauxite was imported into the United States from 11 countries in 2004. The principal suppliers of this 10 Mt (11 million st) of imported ore were Jamaica (33 percent), Brazil (25 percent), Guinea(23 percent) and Guyana (11 percent). The average value of imports, cost, insurance and freight (c.i.f.) U.S. ports, was $31/t ($28/st). Calcined refractory-grade bauxite imports were 165kt (182,000 st) with an average value of $146/t ($132/st), c.i.f. U.S. ports. China supplied 70 percent; Guyana, 22

Jan 1, 2005