Search Documents

Simulator technology has advanced to the point where the cost of mining equipment simulators is beginning to make commercial sense. Simulator-based evaluation allows operators or potential employees to be assessed in a pseudo-real environment under surface and underground mining conditions. Simulator training also allows operators to be exposed to emergency and advanced situations such as brake or steering failure or a tireblowout. ThoroughTec, of South Africa, provides simulator equipment to the mining industry. The company’s various packages of simulator products provide an unbiased evaluation score that removes human error from the assessment process. This same evaluation score is also presented at the end of normal training or refresher training sessions. In this way, the simulator helps eliminate bad habits and improve efficiencies.

Jan 1, 2003

By Y. P. Chugh

A novel dry and wet air dust filter concept was conceived and demonstrated successfully at two mines. A steel-wool and a fiberglass filter, suitable for underground use were identified through laboratory testing and demonstrated in the mine. The steel wool filter was operated with and without water sprays while the fiberglass filter was only operated in the dry mode. The dry steel wool filter provided a dust capture of 37% at a negligible pressure drop. When fine misting water sprays were used on the steel wool filter, the dust capture increased to 51% again with a negligible pressure drop. The filter screen also remained clean and no change in air flow characteristics was observed as a function of time. The dry fiberglass filter however did not perform as well achieving only 11% dust capture while introducing a significant resistance to air flow. This technology is seen to have several applications in underground coal mines.

Jan 1, 2009

By J. Bartrum

Semi-autogenous, (SAG), milling operations can realize substantial Increases in mill throughput by removing and crushing critical size, slow grinding, material from the SAG mill. Full-scale plant testwork showed that modifying the Kidston SAG/ball circuit to a semi-autogenous-ball milling-crushing (SABC) circuit would increase plant throughput by 25 to 30%. The methods used to determine the value of the SABC circuit and the design of the circuit are discussed.

Jan 1, 1988

By Leroy O. Gieseke, John B. Begley

If the particles produced and transported in your plant are as chunky as rough crushed coal or as fine as cement, there are probably several conveying and elevating systems suitable for your operation. The problem is deciding which is most suitable in terms of space, energy cost, allowable product degradation, productivity, and angle of movement. Each conveying and elevating method should be fit to the products it can handle successfully, to desirable economics, and to suitability for the overall operating scheme. Matching along these lines will result in selection guides that should be useful for many years, although design evolution is expected for the materials handling equipment involved. There are several common bulk material handling devices for moving solids: belt conveyors, screw conveyors, bucket elevators, chain conveyors, and en-masse conveyors/ elevators. En-masse conveyor/elevator equipment is commonly compared and contrasted with the other devices. These comparisons often involve en-masse versus all others. En-masse has developed into a versatile technique because the machines can move materials horizontally, vertically, or in closed circuit. Such machines unload, elevate, store, reclaim, and distribute materials-all without ancillary equipment except for chutes and gates. Bulk material can be carried, as with a belt conveyor or bucket elevator; pushed, as with a flight or screw conveyor; bumped, as with a vibrating conveyor; blown, as with a pneumatic conveyor; fluidized, as with a dense phase pneumatic conveyor; or by applying internal forces to it to induce "en-masse" flow. Conveying en-masse is analogous to the flow of a fluid in an open channel, and elevating en-masse is analogous to the flow of fluid in a pipe. In the case of a fluid, flow is caused by a differential in pressure. With en-masse movement, flow results from resistance to shear induced by the movement of chain and flights.

Jan 12, 1980

By D. R. Wilburn

This summary of international mineral exploration activities for 2006 draws upon avail-able information from literature, industry and U.S. Geological Survey (USGS) specialists. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents analysis of the mineral industry based upon these data. Two types of information are reported and analyzed in this annual review. They include budgetary statistics provided by Metals Economics Group (MEG) of Halifax, Nova Scotia, and information on regional and site-specific exploration activities that took place in 2006 compiled by the USGS.

Jan 1, 2007

This geometallurgical study examines the gangue mineral variability at the Bingham Canyon porphyry copper mine in Utah. Understanding an orebody?s mineralogy is important for mine and mill planning because it provides information on the size, texture, and distribution of ore minerals, the relationship between ore and gangue minerals, and the extent and type of alteration. Quantification of the mineralogical variability and properties of an orebody provides valuable input to the ore model and may have a significant effect on recovery optimization. This study was designed to be carried out on an initially detailed scale in order to develop a robust methodology for measuring and quantifying specific parameters, such as the distribution of mineral phases, alteration assemblages and fractures from key ore domains at the Bingham Canyon mine (Figure 1). Details of the methodology are reported below. This technique can be applied to testing the impact of mineralogy on a number of processing parameters. [ ] Figure 1. Ore domain map of Bingham Canyon (Kennecott Utah Copper, 2003) showing the 33 geometallurgical ore domains. The samples for this study were collected from the northwest part of the deposit circled on the map. PROJECT BACKGROUND Geology The Bingham Canyon deposit is a large porphyry Cu-Mo-Au deposit with associated skarn and base-metal replacement deposits mined in an open-pit mine measuring about 2.5 miles across and 4,000 feet deep. The deposit is hosted by the Bingham Stock, a Late Eocene to Mid-Oligocene intrusive complex. The skarn is hosted by the Late Carboniferous-age Bingham Mine Formation, which is comprised of quartzites and basal limestones (Babcock Jr. et al., 1998). The Bingham Stock is a composite intrusive complex that was emplaced over a period of about two million years. The oldest phase is described as a fine-grained equigranular monzonite (MZ), which intruded the country rocks at 39.8 ± 0.4 Ma (U-Pb zircon TIMS age) (Parry et al., 2001). Subsequently, the quartz monzonite porphyry (QMP) was emplaced, followed by intrusion of a latite porphyry (LP). The final intrusive phase, which forms narrow dikes that crosscut the Bingham Stock, is represented by a quartz latite porphyry (QLP), which is dated to 37.5 ± 0.4 Ma by 40Ar/39Ar dating of sanidine (Deino and Keith, 1998). Also present, are a minette dike in contact with a QLP dike (Waite et al., 1998; Deino and Keith, 1998), and a biotite porphyry (BP), a quartz latite porphyry breccia (QLPbx), and a pebble dike (Redmond, 2002). The copper orebody is centered above the Bingham Stock and forms an inverted cup shape with three high-grade copper zones extending to depth. Molybdenite mineralization occurs within and extends below the copper orebody, but is not correlated with copper mineralization. The main sulfide assemblage is chalcopyrite, bornite, molybdenite, and pyrite. Gold is locally intergrown with chalcopyrite and bornite (Babcock Jr. et al., 1998; Phillips et al., 1998). The surrounding country rocks host skarn deposits with three main ore types - garnet skarns, massive sulfides, and iron oxides. The garnet skarns contain chalcopyrite and pyrite with magnetite veins. In the massive sulfides chalcopyrite and pyrite occur either in banded sulfides or in unconsolidated microbreccias. The iron oxides contain disseminated chalcopyrite with minor chalcocite and bornite (Harrison and Reid, 1998). The deposit is overprinted by several stages of alteration. Potassic alteration is concentrated at the center of the deposit. It is surrounded and partially overlapped by a propylitic alteration zone. Both zones are overprinted by sericitic alteration. In the northern part of the deposit evidence for argillic alteration can be found (Bowman et al., 1987). Similarly, the skarn deposit was also overprinted by several stages of alteration: wollastonite, idocrase, and garnet in cherty limestones, and quartz and diopside forming in calcareous quartzites. Distally, diopside was replaced by talc, tremolite, dolomite, secondary calcite, and pyrite, and quartz and sulfide veinlets with biotite and actinolite selvages are present. Andradite garnet, diopside, quartz, magnetite, hematite, and copper sulfides were overprinted by wollastonite (Babcock Jr. et al., 1998). Because the monzonite, quartz monzonite porphyry, latite porphyry, and quartz latite porphyry host the bulk of the mineralization, our research is focused on these lithologic units. Geometallurgy On the basis of geological (lithology, alteration assemblages, fracture density, copper mineralization) and metallurgical properties, the deposit has been divided into 33 ore domains by mine geologists and metallurgists (Figure 1). In map view, these domains cross geologically defined boundaries (MZ, QMP etc.). These domains reflect regions of the deposit that have particular, mapable attributes or properties. They reflect a combination of geological and mineralogical characteristics that combine to impact processing. Alteration, for example, as shown by talc mineralization, is one such key feature. Hardness may reflect the absence of sericitic but presence of potassic alteration. Structural discontinuities such as faulting, fracturing, or development of void

Jan 1, 2009

By A. Yehia, M. I. Al-Wakeel

Flotation behavior, of magnesite and dolomite pure minerals was studied separately. Rice bran oil (a source of fatty acid ) was used as a collector for both minerals . The aim of this study is to find a separating zone in the flotation of these pure minerals to be used in the separation of their mixture. Factors affecting the flotation process, such as pH and collector, were studied. It was found that magnesite can be separated, from its mixture with dolomite, in the pH range of 5-7. At this pH range flotation recovery of dolomite reaches~98% where magnesite reaches ~20% only. Besides, the effect of collector concentration on the flotation shows that the separation of magnesite from dolomite is feasible at a collector concentration of 3x10-4 M. At such concentration, dolomite recovery reaches ~98%, where magnesite reaches 25%. The differences in the flotation behavior of dolomite and magnesite were investigated by studying the adsorption isotherms of rice bran oil on magnesite and dolomite surfaces. The adsorption study indicates that while there is an excessive adsorption on dolomite surface, the adsorption density on magnesite was restricted to be lower than monolayer capacity. The adsorption behavior of dolomite and magnesite was discussed in the light of their solubility and crystal structure. It was found that due to the higher solubility of dolomite than magnesite, Ca2+ and Mg2+ ions are available and more reactive on dolomite surface increasing collector adsorption. In addition, it was indicated that dolomite mineral has a crystal lattice structure more compatible to the geometry of the fatty acid carboxylic group than magnesite. However, the adsorption of collector on dolomite surface is more compact and more regular than on magnesite surface.

Jan 1, 2000

By M. Oliverio

The Cigar Lake uranium deposit was discovered in 1981 at the south western end of Waterbury Lake, approximately 660 km north of Saskatoon in the province of Saskatchewan (see Figure 1). It is the largest undeveloped high grade uranium deposit in the world. It contains proven and probable reserves of more than 226 million pounds U3O8 at an average grade of 20.7%. The world average grade is less than 1% U3O8. [ ] The ore body is located about 450 m below surface at the interface between sandstone above and basement rock below (see Figure 2). The sandstone is fractured rock and saturated with water. This makes water inflow a real hazard at the mine. In fact there have already been two significant mine inflow events. The first of these occurred in October 2006 and resulted in the flooding of the mine. The second occurred in August, 2008 during mine recovery activities.

Jan 1, 2011

By Z. Konstantinovic, M. Ahrens

Due to the large installed electrical power and the large number of electric drives in minerals and mining plants power factor compensation and harmonic filtering has always been an important issue. For the design of harmonic filter and power factor compensation installations several approaches can be taken. The paper describes different concepts and their advantages and analyzes special requirements and design considerations for minerals and mining plants. It also highlights areas where problems can occur and which points need to be addressed carefully. Optimized designs and solutions are discussed in case studies and the resulting energy savings and benefits for the plant operation are shown.

Jan 1, 2007

By H. Seguin, J. A. Le Gac, S. Bernhard, P. R. ZETTWOOG

The "Service de Protection Technique"of the "Institut de Protection et de Sûreté Nucléaire" was asked by the Commission of European Communities to conduct measurement campaigns which would make it possible to evaluate, on an experimental basis, the collective risk to miners exposed to radon in underground, non-uranium mines located in countries within the European Community. 1. METHODOLOGY USED TO CONDUCT THE CAMPAIGNS This campaign is original in that direct measurements of the individual monthly exposure to potential [a]-energy from short-lived radon daughters are made using personal [a]-dosimeters described previously (1). We call this type of dosimetry "personal dosimetry". The workers who wear the personal [a]-dosimeters were selected taking into account the various categories of workers and their work assignments in the various areas of the mine. Another way of finding out the occupational exposure of these miners consists in making numerous measurements of the radon concentration at the various work places, taking into account the time spent at each place by each worker. This procedure is too complex for an evaluation of the collective risk as requested by the Commission of European Communities and was therefore rejected. Additional data was gathered during these measurements campaigns using the following techniques (table 1). [ ] (1) Current [a]-dosimetry as practiced in France - SPT international report N° 234 - February, 1981 - P. ZETTWOOG The mines were chosen to include a larger variety of types of ore, of geological situations, and of mining methods. 2. RESULTS OF THE RADON DATA-GATHERING CAMPAIGNS 2.1 – [Uranium content of the surrounding rocks and ore] The samples taken during the campaigns make it possible to establish the U content in the rocks of the mines selected. These values, from 2 to 15 ppm, are slightly higher than those usually found (2 to 5 ppm) (table 2). [ ]

Jan 1, 1981

By K. Sasaki

Diffusion phenomena in mine airways are important to trace gas and dust introduced into mine ventilation flows. Authors have carried out tracer gas measurements to check mine ventilation using concentration-time curves measured in mine airways, however dispersion mechanism to enhance effective diffusion have not been cleared. A numerical model using discrete tracer points dosed into tube flow has been presented to simulate their movements in consideration of turbulent velocity profile and fluctuation. Numerical simulations have been carried out to predict distributions of dosed points in tube flows with turbulent velocity profile, turbulent intensity profile and Reynolds stress. The numerical simulation results show that a combination of turbulent velocity profile and fluctuation creates extremely large dispersion of points in longitudinal direction and concentration curve with long tail was observed. This dispersion by velocity profile and fluctuation contributes large effective diffusion coefficient compared with original diffusion coefficient dominating in uniform velocity fields. Furthermore, the effect of Reynolds stress on the concentration-time curves is discussed.

Jan 1, 2009

By S. -Y. Hwang

An ongoing problem for industry in Korea is effective removal of heavy metals from and safe disposal of spent power plant fly ash. This research endeavor attempts to develop selective separation of Ni from leach liquor using a selective chemical precipitation method. The research was conducted by changing two variables, the pH and the concentration of ions in solution. The effect of other ions present in the system on the separation efficiency of Ni species was also investigated by adjusting OH and NH3 concentrations. In the pH range of 7-9, the chemical precipitation method produced a high yield of Ni by precipitation from the fly ash leach liquor.

Jan 1, 2010

By Yaxiong Wang, Yong Li, Yuedong Wu, Haigang Dong, Jiachun Zhao

A roasting-leaching process has been developed for concentrating platinum group metals (PGM) from a PGM-containing ferroalloy. The optimized roasting conditions used a NaOH-to-ferroalloy mass ratio of 1.2 at 600 °C for 2 h. The roasted product mainly comprised Na4SiO4, NaFeO2 and Fe2O3. The iron oxide and sodium silicate associated with the roasted product were leached in water and dilute sulfuric acid solution, while the PGM was concentrated in the acid-leached residue. A PGM concentration of 23.4% was obtained with assaying, and the concentration factor of PGM from the ferroalloy to PGM concentration was greater than 9.

Jun 14, 2021

By Stephen H. Stow

Economically important heavy minerals have been studied in the sediments of offshore Alabama and Mississippi. Sandy samples have been collected from a 200 square mile area from Dauphin to Horn Islands. The minerals concentrate in sediments under 10-35 feet of water and may reach 2.4% by weight. The distribution of total heavies is related to the hydrodynamics of offshore Alabama-Mississippi; the greatest concentrations are in the Gulf where the longshore current is diverted from its westerly flow. Preliminary observations indicate that the distribution of individual minerals can be correlated with wave energy, particle size, specific gravity, and morphology of the mineral grains. The coarser, lighter minerals--kyanite, sillimanite and staurolite--are concentrated in relatively low energy areas in the Mississippi Sound and at the end of Dauphin Island in the Gulf; maximum concentration for each is 34.5%, 6.0% and 43.2%, respectively, of the heavy minerals. The smaller, more denseminerals--ilmenite, rutile, leucoxene, zircon and monazite--are concentrated in high energy areas in the Gulf; maximum concentration for each, respectively, is 42.0%, 5.9%, 9.652, 10.7% and 1.3% of the heavy minerals. On the basis of a minimum concentration of 1% heavy minerals, two areas have been identified and the total amounts of different minerals have been calculated to a depth of 25 feet of sediment. The data are preliminary and in no way indicate recoverable reserves, but they do show that on the order of 20 million tons of heavies exist. These deposits should be termed "indicated resources".

Jan 1, 1975

The efficiency of a coal mine ventilation circuit is usually measured by the ratio of the sum of the face quantities divided by the quantity supplied by the fans. Other types of systems use the power delivered to the power supplied to measure efficiency. This paper argues the case that the current measure may be inadequate and that by also looking at the power ratio, ventilation may be better managed. Problems associated with failing ventilation systems would be highlighted earlier so that crisis management could be avoided.

Jan 1, 2009

Membrane technology has been available for over 36 years, but has been used sparingly in the general mining industry. However, recent developments in polymer chemistry, spiral wound element construction, pretreatment equipment and techniques and an expanded understanding of membrane fouling and cleaning techniques have dramatically improved the reliability and robustness of membrane based systems in the mining industry. Harrison Western has expanded the use of this “new” technology to enhance the use of membrane technologies to separate metals from large volume heap leach mining solutions containing copper, zinc, and iron, gold or silver. Moreover, membrane technologies are ideally suited to fractionations that add value to processing fluids from refineries like separating metals from acids or concentrating acids and producing high quality process fluids. Finally, wastewater from Acid Mine Drainage (AMD) or, as in the case of the Newmont Yanacocha Mine in Peru, the treatment of excess barren leach solution created during the rainy season, can be cost effectively processed to meet World Bank Standards for surface discharge. Polymeric membranes, specifically thin-film composites, have been developed that will purify, fractionate or concentrate gold, silver, copper, zinc or nickel. Recent applications have been developed for spiral wound modules that operate across the pH spectrum from 0 to 14. Systems using membranes have been constructed that operate on feed streams from 140° C to 300 centipoise. Opportunities exist to apply membrane technology to concentrate gold, silver, copper, zinc or nickel using thin film composite membranes. Engineered membrane types can operate across the spectrum from low pH (<2) acid applications to high pH > 10 cyanide applications. Incorporating HW EMS™ membrane technologies into current mining operations could allow one to increase production because the membrane technology would be used to pre-concentrate heap leach solutions, and therefore, increase utilization of existing extraction and refinery capabilities.

Jan 1, 2007

By T. R. Ellis

Australia’s mineral valuation code continues to evolve, while mineral valuation standards are also being written for Canada and Southern Africa. The author is leading a task force for writing the extractive industries addition to the International Valuation Standards. Meanwhile, the International Accounting Standards Board is continuing the development of an extractive industries addition to its International Financial Reporting Standards, with an emphasis on valuation reporting. This paper analyzes the need, content and ownership for a U.S. minerals appraisal standard in the context of both these developing international standards and also existing U.S. regulations and appraisal standards. The author provides many questions for research and debate.

Jan 1, 2003

By T. P. Dolley

Domestic production of industrial sand and gravel in 2004 was about 29 Mt (32 million st), a 6-percent increase from 2003. This increase was buoyed by a robust construction sector of the U.S. economy. U.S. apparent consumption was 30.3 Mt (33.3 million st) in 2004, an in-crease from 2003. Imports were about 490 kt (540,000 st) in 2004, an 11-percent increase from 2003. Imports of silica are generally of two types. They include small-quantity shipments of very-high-purity silica or a few large shipments of lower grade silica that were shipped only under special circumstances (such as very low freight rates).

Jan 1, 2005

By Richard Gertsch, Jack Eloranta, Leslie Gertsch

An ongoing research program is characterizing the ore qualities that most affect mine and mill processing of iron. Current practice uses assays of magnetic iron and silica, but additional qualities are needed for advanced process control. If additional qualities can be measured from core, blastholes, or process samples, they can be modeled and controlled similarly. What qualities, other than assays, hinder or facilitate beneficiation at each processing step, and how can they be measured in the mine/mill ore stream? This paper describes preliminary determinations of the effects of ore chemistry, hardness, blasthole drill performance, fragmentation control, and grindability on mill performance.

Jan 1, 2005

By Jennifer B. Leinart

Sixty percent of the mines responding to the sixth annual Mining Cost Service labor survey reported increases in wages averaging 3.4% over the preceding 12 months. Only one mine reported a decrease in wages and this was accompanied by initiation of a substantial profit-sharing plan. Thirty-nine percent reported no change in wages. Thirty-seven percent reported using some form of incentive bonus plan. Mining Cost Service annually surveys coal, metal, and industrial mineral mines throughout the United States. Information about wages, benefits, and incentive bonus plans is part of an extensive data collection program to monitor cost areas of significance to the mining industry. This year, 131 mines responded to the survey. The data is collected by sending questionnaires to personnel managers at active mining operations. The information included in this article was taken from the returned forms, from labor contracts provided by some of the mines, and from followup telephone calls. This year&apos;s data was collected between November 1988 and February 1989.

Jan 1, 1990