Search Documents

Infacon 74 The National Institute for Metallurgy, the South African Institute of Mining and Metallurgy, and the Ferro-Alloy Producers' Association of South Africa extend a cordial invitation to participate in the International Ferro-alloys Congress to be held in Johannesburg, South Africa, in April 1974. Obituary RICHARD AUSTIN COOPER On the 31st March 1972, a once very active member of the Institute, R. A. Cooper, died at the age of 82. He had served on the Council for many years and was Vice-President in 1933/34. ALEXANDER JEREMIAH ORENSTEIN CB., CM.G., C.B.E., LLD., D.Se., M.D., M.R.C.S., F.R.CP., F.R.S.H. Dr Orenstein, who died on the 7th July 1972 at the age of 92, was so well known and so widely acclaimed during his lifetime that it is difficult to add to the tributes which have already been paid to him.

By I. M. MacGregor

This paper discusses the possible use of petrological data and proximate analyses in the prediction of cutting forces for coal. It is restricted to the development of univariate predictors based on data from thirteen collieries in five major Transvaal and Orange Free State coalfields and three coal provinces. The aim of the work was the identification and development of the best predictors of mean peak cutting force and Hardgrove grindability index from among the independent variables evaluated. The data, which were obtained by use of the penetrometer developed by the Chamber of Mines Research Organization, were processed according to the SPSS computer package. The analysis revealed reasonable correlations between the Hardgrove grindability index and (1) the volatiles and vitrinite content in the Vereeniging-Sasolburg and South Rand Coalfields, (2) the contents of vitrinite, vitrinite plus exinite, and minerals plus inertinite in the Eastern Transvaal Coalfield.

Jan 1, 1985

By H. M. Friede

Notes on the composition of pre- European copper and copper-alloy artefacts from the Transvaal by H. M. Friede. Ph.D. (Visitor) Seven copper artefacts (five ingots and two ornaments) found at prehistoric sites in the Transvaal were submitted to analysis. All the artefacts showed a high copper content and a relatively Iow level of impurities. A little-known ingot type from the Limpopo Valley ('nail' ingot) is described, and its analysis is given. The analysis of two copper ornaments that come from sites dated to the 5th Century AD. and the 11th Century AD. showed the constancy of the composition of copper articles over long periods. The well-known 'Blaauwberg Ingot' was re-analysed, and the results showed that this ingot cannot be regarded as a true bronze. Analytical values for the composition of three brass artefacts from Bambandyanalo (Mapungubwe), Northern Transvaal, are given. Some aspects of pre-European bronze manufacture and brass smelting, and of early metal trade from the East Coast into the interior of South Africa, are discussed.

Jan 2, 1975

By P. R. Beeley

Metal founding - a modern perspective The recent development of metal founding is reviewed in the context of basic requirements for the successful manufacture of cil;5ti,ngs.Progress has been related to the two interdependent fields of process technology and product characteristics. . After a brief review of the growth of the traditional industry. various features of the modern industry are discussed. Reference IS made to current trends in process technology and to the introduction of new techniques affecting production engineering, product quality. and the general nature of the industry. Metallurgical aspects of metal founding are considered, and modern techniques for the control of casting conditions are examined. These aspects are related to the structure and quality of cast metal and to the development of newer types of cast material and product.

Jan 9, 1976

By R. M. Lamya

A semi-empirical kinetic model was developed for the atmospheric leaching of a Ni-Cu matte in copper sulphate-sulphuric acid solution. Kinetics of the leaching process was studied as a function of initial copper ion concentration, initial acid concentration, temperature, stirring rate and particle size distribution. The kinetic model was developed on the basis of the leaching mechanism and chemical reactions of the leaching system investigated, and was evaluated by comparing the model predictions to experimental data. The model was found to satisfactorily fit the trends in the leaching of the metals, namely copper, nickel, cobalt and iron.

Jan 1, 2009

By J. W. Wilson, P. C. Graham

Raise-boring experiences in the gold mines of the Anglo American Corporation Group by J. W. Wilson M.Sc., M.I.M.M., F.S.A.I.M.M., M.A.I.M.E. and P. C. Graham M.Sc. (Eng.) Gold mining is being carried out at ever-increasing depths in South Africa. For reasons of safety and human comfort, it is becoming imperative for raises to be developed by means other than conventional drilling and blasting. Raise-boring is an attractive alternative method. Initial raise-boring experiences in South African gold mines showed disappointingly high costs due to the abrasivity and difficulty of drilling Witwatersrand quartzites. Consequently, a research and development project was instigated with the objective of making raise-boring an economically viable technique in hard abrasive rock. A Robbins 61R raise-borer was made available to the Research and Development team and a number of raises have been drilled. During these trials two advances in cutter design were tested. This paper presents the results obtained, including drilling costs, and provides details of the equipment used.

By Ralph H. Nafziger

This paper reviews the major deposits of lower-grade chromite in the world, and a wide variety of methods used for the recovery of chromium from them. Gangue materials in more coarsely sized ores can be separated by gravity means, whereas flotation techniques are required for finer-grained materials. However, unless there is considerable Iron In the ores, physical means cannot increase the Cr/Fe ratios. Chemical techniques such as hydrometallurgical methods, chlorination, roasting and leaching, and smelting are required for this purpose. A greater understanding of the physical properties of chromites and the chemical reactions that take place in the recovery operations is required before. the recoveries from lower-grade chromites can be maximized. More efficient recovery operations can be realized If It can be shown definitively that the reduction of chromites occurs via either a gas-solld or solid-solid mechanism, for example. The effects of specific impurities on the chromite reduction reactions need to be better understood, as do reagent and pH control in the flotation of chromite.

Jan 1, 1982

The Annual General Meeting of the South African Institute of Mining and Metallurgy was held in Kelvin House, Johannesburg, on Wednesday, 27th August, 1980. Mr D. A. Viljoen (President) was in the chair and declared the meeting open at 4.05 p.m. Obituaries President: It is my sad duty to announce the death of the following members of the Institute: T. C. A. Meyer (Past President, 1941 to 1942); E. G. Harding, T. A. Stannard, C. T. Hardy, W. C. Jackson, J. S. Sinton, G. H. Duggan, H. H. A. Muller (Life Fellows); W. M. Frames, K. Gebhard, W. M. Walker, S. L. S. Swart, N. W. Stansmore, H. E. Allen, B. W. F. Towne, R. A. Wilson, D. Waterman (Fellows), R. M. Peterson (Life Member); D. L. Gibbs (Member); B. M. Williams (Asso¬ciate Member); D. B. T. Cresswell, P. G. Guernier (Associates). As a mark of respect to the memory of the deceased, and in sympathy with the bereaved, please rise and observe a few moments of silence. Notules President: Kan ons die notules van die Algemene Jaar¬vergadering, wat op 22 Augustus 1979 gehou was en in die September uitgawe van ons Joernaal gepubliseer is, bevestig? Bevestig.

Jan 1, 1980

The Annual General Meeting of the South African Institute of Mining and Metallurgy was held in Kelvin House on Wednesday, 22nd August, 1979. Dr M. G. Atmore (President) was in the chair and declared the meeting open at 16h00. Obituaries President: It is my sad duty to announce the death of the following Members of the Institute : Brigadier R. S. G. Stokes, Honorary Life Fellow and Past President ; J. A. Arthur, C. L. Cartwright, R. B. Greaves, A. A. Haynes, G. Ross, M. W. Richards, W. T. Stobart, E. Veres, G. V. White, and A. G. Williams, Life Fellows; A. J. H. Pole, D. T. McMurray, P. G. O. Pretorius, A. E. D. Rubidge, A. M. Seccombe, and R. R. Uren, Fellows; R. E. Oltman, R. B. Richardson, and G. P. Rundle, Members; S. F. Dench and S. van Wyk, Associates. As a mark of respect to the memory of the deceased, and in sympathy with the bereaved, please rise and observe a few moments' silence. Minutes President: May we confirm the minutes of our last Annual General Meeting, which was held on 23rd August, 1978, as published in the November issue of the Journal? Agreed.

Jan 1, 1979

By M. H. Moys

The capacity of grinding mills can be maximized by use of measurements of mill power and bearing pressures. The criterion is as follows. If the derivatives with respect to time of the power and bearing pressure signals have the same sign, the volume of the mill load is smaller than the optimum value; if they have different signs, the volume of the mill load is greater than the optimum value. Few attempts have been made to use measurements of bearing pressure in the estimation of absolute values for the parameters that define the state of the mill load (e.g, mass, volume, and dynamic angle of repose) because the bearing-pressure signal is a complex function of these and other parameters. This paper gives a mathematical model that relates bearing pressures to these parameters. The theoretical values obtained from this model are compared with experimental values, and it is concluded that the model constitutes a good description of experimental reality. If accurate measurements of the load supported by each bearing are available, the model can be used in the estimation of the mass of the load in the mill. If independent estimates of the volume of the load or the dynamic angle of repose are available, the other parameter can be estimated from measurements of the bearing loads.

Jan 1, 1980

By A. Koursaris, J. B. See

An investigation is described in which the resistivities of Mamatwan manganese ore, Delmas coal, and Iscor coke, at temperatures or up to 1400°C were determined, as well as the resistivities of mixtures of ore of a constant size range with Delmas coal or Iscor coke of three different size ranges. The resistivities of the ore and the coal were characteristic of those for semi-conducting materials, were strongly influenced by temperature, and decreased by several orders of magnitude between room temperature and IOOO°C. The resistivity of the coke changed only slightly between room temperature and 1400°C, and the resistivity of the coal approached that of the coke at I300°C. This provides support for the theory that the resistivity of carbonaceous reducing agents is primarily a function of heat treatment, and not of the rank and composition of the coal. Above 1200°C, the resistivity of mixtures of ore and coke fell steeply owing to an increase in the volume fraction of coke in the mixture and to the formation of slag. The results were similar for the three different size ranges of coke. The extremely high resistivities of ore-coke and ore-coal mixtures at Iow temperatures indicate that there is unlikely to be much conduction of current in the higher regions of a furnace. Thus, the resistance of a furnace is governed mainly by the conditions at the electrode tips and in the molten regions. To explain the very Iow resistances of furnaces, usually, about I m£?, it would be necessary for investigations to be conducted under conditions similar to those in the active zone of a furnace.

Jan 1, 1980

By H. A. D. Kirsten

Mining-induced seismicity is usually evaluated in terms of continuum elastic analyses, and is quantified in terms of energy release rate as state parameter and excess shear stress along particular features on which failure may be induced. Although both of these quantities are representative measures of potential seismic activity, elastic analyses do not enable the associated stresses and displacements in the rock in which failure occurs to be evaluated reliably. The paper compares the effect of depth, span, support stf1Jhess, field stress ratio, and discontinuity strength on mining induced seismicity determined from elastic analyses and from analyses in which discontinuities in the rock are allowed to fall. It is, accordingly, shown that the incidence and magnitudes of potential seismic events and the net excess shear as representative state parameter cannot be determined reliably from elastic analyses that do not account for the failure of ubiquitous discontinuities. The magnitudes of seismic events in rock in which ubiquitous discontinuities are allowed to fail are very considerably overestimated in elastic analyses. The extent of the seismic source region and the associated seismicity do not increase with depth, which, together with the improved containment of the concomitant rockburst damage by backfill is reassuring for mining at greater depth in future. For conventional support, the magnitude of potential seismicity increases for an increase in span in elastic rock, but remains unaffected in non-elastic rock. For backfill, the magnitude of potential sesmicity decreases substantially in elastic and non-elastic rock for an increase in span. Increases infield stress ratio very significantly reduce potential seismicity irrespective if the type if analysis, but effect the distribution if potential seismic events very differently in elastic and non-elastic rock.

Jan 1, 1994

By M. J. Deats

Your article on page 202 of the August 1993 Journal refers. I was surprised to read that this grant was first introduced in 1984 as it was awarded to me (albeit under the auspices of The Institution of Mining and Metallurgy, London) as long ago as 1964, and I spent two very profitable months in Sweden at that time. Training in job-skills * A South African mine is leading the way in providing alternative job-skills to staff in a bid to upgrade services in local communities and create greater economic empowerment. In recent months, 85 employees of the Associated Manganese Mine (ASSMANG) in the Western Cape have learnt skills as diverse as candlemaking, shoemaking, concrete-product manufacturing, and brick production through a newly established community training centre.

Jan 1, 1993

By P. C. van Aswegen

The Schools A school on 'Measurement, Process Control and Optimization in the Minerals Industry', organized by The South African Institute of Mining and Metallurgy, was presented twice by course leader Dr Ken Garner, ably assisted by the staff of the Measurement and Control Division of Mintek. The first school was held from 16th to 20th July, 1984, at the University of the Witwatersrand, and the second from 11th to 15th February, 1985, at Mintek. Project development The Sydney Branch of the Australasian Institute of Mining and Metallurgy will hold a second Project Development Symposium in Sydney between 7th and 10th October, 1986. This second symposium will extend the range of topics covered by its predecessor in 1983 to emphasize planning (including strategic planning), construction, and project commissioning.

Jan 1, 1985

By D. R. Hardman, J. W. Oberholzer

Based on information supplied by South African collieries to the Coal Mining Laboratory of the Chamber of Mines since 1978, the paper outlines the general performance of the continuous miners used and gives the results more-detailed studies of the cutting, loading, and transportation processes. On average, the continuous miners produced coal at a rate of 76 t per operating hour, which, at an average machine availability of 67 per cent, resulted in a production of 51 t per total hour. The cutting rates varied between and 250 t/h but, owing to machine and system inefficiencies, the overall production rate varied between 92 and 48 It is concluded that, if the collieries concentrated on improving their machine utilization procedures and operating practices, they could increase the overall production from their continuous-miner sections.

Jan 1, 1987

By R. C. Urquhart, W. P. Channon, D. D. Howat

The mode of current transfer between electrode and slag in the submerged-arc furnace . by W. P. CHANNON, B.Sc.(Eng.)(Student Member), R. C. URQUHART, M.Sc.(Eng.), ;'h.D.(Visitor), and D. D. HOWAT, B.Sc., Ph.D.(Fellow) An account is given of a laboratory experiment in which the resistivity of a primary slag like those produced in the manufacture of high-carbon ferrochromium was measured at current densities typical of operation in a submergedarc furnace. It was shown that the current flow from graphite elec trode to molten slag obeys Ohm's Law when electrode current densities are less than 12 A/cm". At higher current densities, arcing occurs from the electrode tip to the slag, causing an imbalance in the rate of heating in the furnace burden.

Jan 8, 1974

The value of incentive payments in the mining industry by K. SMITH, A.R.S.M., B.Sc. (London) (Member) This paper reviews the history of incentive payments in the mining industry, and gives some indication of the magnitude of improvement that has been achieved by this means in the past. The objective is to promote a more general belief in the efficacy of these methods, and thus to encourage their wider and more effective application by mining engineers in general, and by the rising generation in particular. It is concluded, from a consideration of current productivity levels in the gold-mining industry (still South Africa's leading revenue earner), that further substantial improvement can be achieved by a better understanding of the time-tested principles of incentive payments.

Jan 5, 1974

By J. J. Van Rensburg

The commissioning of a test facility for the calibration of anemometers by J. J. VAN RENSBURG (Student Member). After the erection of a commercially produced open-jet wind tunnel for the calibration of the anemometers used in mine ventilation, the wind tunnel was calibrated for routine use. There is a choice of five orifice plates. which, together with a variable-speed fan, can give a measurable range of air velocities in the test section from about 0,05 to 35 m/so The orifice plates were calibrated against a standard pitot tube, and it is now necessary only to measure the pressure drop across an orifice plate and to read off, from a set of graphs, the true outlet velocity in the test section. The paper describes the underlying theory and the test results.

Jan 4, 1975

In order to test the applicability of elastodynamic codes in the modeling of mining related problems, comparisons are made between seismic data and numerical analyses. The dynamic finite difference program WA VE is used for the modeling of a horizontal stope in a deep mine. The slip along a vertical fault situated within the positive excess shear stress lobe of the stope initiates seismic waves. The stope-fault geometry is modeled in both two and three dimensions. The three dimensional non-slip weakening WAVE analyses correlate well with Brune's analytical model. For accurate modeling of the peak particle velocities predicted by McGarr's empirical relationship, it is recommended that a three-dimensional stope -fault model is used, with the amount of slip weakening dependent on the magnitude of the event.

Jan 1, 1995

By J. W. Klokow, S. L. Mulder

Early removal of the shaft reef is usually considered necessary on deep level South African gold mines to avoid damaging stress build-up associated with traditional shaft-protection pillars. In the case of the relatively shallow Beatrix Gold Mine it was largely motivated by early access to ore and the consequent earlier return on invested capital. A number of options were considered to protect the shaft from possible damaging stress changes and to minimise deformations in the shaft-reef area. Numerical modelling was used to evaluate the options and to quantify as accurately as possible the likely deformations to be accommodated by the shaft steelwork designs. The option chosen was a combination of strategically placed satellite pillars and yield pillars, and backfill. Following the mining of a small inner cut during the shaft sinking process, full-scale mining is progressing away from the shaft. Suitable instrumentation has been installed to monitor deformations associated with the shaft reef removal. Enlever rapidement le filon du puits est en général considéré nécessaire dans les galeries de fond des mines d’or sud-africaines pour éviter l’accumulation nuisible de contraintes associée aux piliers de protection de puits traditionnels. Dans le cas de la mine d’or Beatrix, relativement peu profonde, l’enlèvement était motivé en grande partie par l’accès rapide au minerai et par conséquent un profit plus rapide sur l’investissement. Un certain nombre d’options furent considérées pour protéger le puits contre les changements de contraintes potentiellement nuisibles, et pour minimiser la déformation dans l’aire puits/filon. La modélisation numérique fut utilisée pour évaluer les options et pour quantifier aussi précisément que possible les déformations probables que la conceptualisation du puits devrait prendre en compte. L’option choisie fut une combinaison de piliers satellites placés à des points stratégiques avec des piliers de protection, et terre de remblayage. Pendant le fonçage de puits une petite coupure intérieure fut exploitée, et maintenant l’exploitation à grande échelle, au-delà du puits, est en cours. Les instruments nécessaires ont été installés pour surveiller les déformations associées à l’enlèvement du filon du puits. Die frühe Entfernung des Riffschachtes wird normalerweise bei südafrikanischen Tiefbaugoldmienen als notwendig erachtet um den zerstörende Druckaufbau zu vermeiden, welcher mit traditionellen Schachtschutzpfeilern verbunden ist. Im Fall der verhältnismäßig flachen Beatrix Goldmine war es hauptsächlich vom frühen Zugang zum Erz und dem konsequenten frühen Rückfluß des investierten Kapitals motiviert. Eine Anzahl an Optionen wurde erachtet um den Schacht vor möglichen zerstörenden Druckänderungen zu schützen und Deformationen im Riffschachtbereich zu minimieren. Um die Optionen zu bewerten und mögliche Deformationen so genau wie nur möglich quantitativ darzustellen die von den Schachtstahlkonstruktionen aufgenommen werden müssen, wurden numerische Modelle verwendet. Die gewählte Option war eine Kombination aus strategisch plazierten exzentrischen Pfeilern und Schutzpfeilern sowie Hinterfüllungen. Nach dem Vortrieb eines kleinen inneren Einbruches während des Abteufens wird der Vollvortrieb vom Schacht weg vorgenommen. Um die Deformationen, die mit der Riffschachtentfernung verbunden sind zu überwachen, müssen geeignete Instrumentenausrüstungen installiert werden.

Jan 1, 2003