Search Documents

By F. Shi , D. Lay, C. Antonio

High Voltage Pulse (HVP) technology has the potential to transform traditional mineral processing practice in the mining industry. HVP pre-treatment has been shown to enable ore preconcentration, achieve ore pre-weakening and improve mineral liberation. In order to improve the efficiencies of these novel HVP applications, it is essential to understand how HVP operational factors affect ore breakage in HVP pre-treatment. A two-level fractional factorial experiment using two rock samples, a gold-copper ore and a basalt sample, was performed to determine which factors have statistically significant influences on breakage probability, size reduction, and energy efficiency, and which factors have insignificant influences. Operational factors investigated include applied voltage, electrode gap, number of pulse discharges, the number of rocks being processed per batch, and rock size. In total, 1920 batch tests were conducted. For ore breakage characterised in terms of breakage probability and the degree of size reduction during HVP pre-treatment, the dominant factors were identified to be the number of pulse discharges, voltage, and the number of particles present in the processing zone. As all these three factors are related to the specific energy, it is concluded that the specific energy is the most important factor controlling ore breakage in HVP treatment. In terms of the efficiency by which spark energy is transferred from the generator energy, the factors found to have the most dominating influence were the particle size, the number of rock particles present in the processing zone and the voltage. Increasing the values of these factors reduced the loss of HVP energy during the energy transfer process. The factorial experiment using the two ore samples with vastly different mineralisation produced similar results. This proves that the dominant factors affecting HVP breakage are generally applicable to different ores types. Keywords: High voltage pulse, ore breakage, factorial experiment, specific energy

Jan 1, 2020

The following diagrams should replace the Figs. 4, 5, and 6 that appeared on pages 412 and 413 of the October 1986 issue. These relate to the paper entitled' A new method for the rapid float-sink analysis of coal fines' by J-P. Franzidis and M.C. Harris Womanpower In 1981 the Publicity Committee of the Federation of Societies of Professional Engineers (FSPE) decided that one way in which the engineering manpower pool could be increased would be by the introduction of womanpower to the profession. Since then, Std 9 and 10 girls have been invited to attend the engineering winterschools held annually at the various universities under the auspices of SAFUES. Coal-mining wastes The 2nd International Symposium on the Reclamation, Treatment and Utilization of Coal Mining Wastes will be held in Nottingham (England) from 7th to 11th September, 1987.

Jan 1, 1986

The Technical Programme Committee-Metals Technology of The South African Institute of Mining and Metallurgy, in association with its Vaal Triangle Branch, held a one-day colloquium on 18th April, 1989, the theme being 'Ferous Pyrometalurgy: A Challenge for South Africa'. The venue was the Auditorium 100 at the campus of the Vaal Triangle Technikon in Vanderbijlpark. Project and contract management A Project and Contract Management Conference is to be held on 19th and 20th September, 1989, at the C SIR, Pretoria. Powder metallurgy The PM 90 exhibition is to be held in Wembley, London, from 2nd to 6th July, 1990. The wide range of powders, processing machinery, and powder-metallurgy components at the exhibition will reflect the growth in this highly specialist industry. Castings and forgings Exhibition organizers, FMJ International Publications Ltd, are set to build upon the success of Castings & Forgings '88, which was held as a joint event with Pat- Cast '88. Castings & Forgings '89-with Pat-Cast '89- has already generated a high level of interest, which has been reflected in the demand for stands. Furnaces FURNACES '90, the eighth in this series of exhibitions for the thermal-processing industry, will be held in Solihul, West Midlands, England, on 6th and 7th March, 1990.

Jan 1, 1989

By B. P. Watson, D. P. Roberts, R. A. Lamos

The Upper Group 2 (UG2) chromitite reef is a shallow-dipping stratiform tabular orebody in the South African Bushveld Complex, which strikes for hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 500 m. Pillars are widely used to support the open stopes and bords. Little work has been done in the past to determine the strength of pillars on the UG2 Reef and design was done using formulae developed for other hard-rock mines. This has led to oversized pillars with consequent sterilization of ore. In this paper we describe a back-analysis of stable and failed UG2 pillars on the Bushveld platinum mines, and provides a strength formula for UG2 pillars. The formula may be used cautiously on all Bushveld platinum mines with similar geotechnical, geometrical, and geomechanical conditions to the pillars in the database.

Aug 1, 2021

By P. Mühlen, C. Nelson

Process control optimisation depends a lot on the availability of timely data from production to give operators a chance to make adjustments before potential process upsets or disruptions happen. A lot of data is already available with newer and updated machine technologies, but what about the process upsets coming from the raw materials that we use? They are natural products and therefore they are not of a stable composition or mineralogy. The production process depends on a certain chemical or mineralogical stability of the raw materials when they come to a roaster, kiln or sintering stage. Only then can the proposed reactions take place and the equipment be operated at stable temperatures. Laboratory analytical technologies have the limitation that they depend on representative samples and have a long time delay. Therefore online (real time) analysers are used nowadays in mining applications to obtain an early indication of the actual mined or to-be-processed ore. Most available technologies can only analyse inorganic content on an oxide or elemental level. Near infrared (NIR)- based online analysers can overcome that limitation and give a real time analysis of organic as well as inorganic composition, if required on a mineral level. The paper will present two case studies where the NIR online technology was successfully adapted.: a) Optimising refractory gold ore processing at the Goldstrike roaster operation b) Optimising the sinter process at a Japanese manufacturer. Keywords: Analyser, NIR, online, realtime, gold, roaster, iron ore, sinter, mineral phase analysis

Jan 1, 2020

By R. o. Cretier, L. A. Cisternas, A. López-Valdivieso, F. Valdes, E. Gálvez, G. Gahona

The size of the particle plays an important role in the flotation of minerals. Comminution allows the release of valuable species and their subsequent recovery. Then, the degree of concentration and recovery will depend on the size of the particle. In this work, we investigated the flotation of coarse particles (-850 +150 μm) of copper ores when using the fluidized-bed separator (HydroFloat® cell) and compared it with the process of conventional flotation with medium size particle (-150 μm) (Metso cell) using seawater. The collector concentration was the main variable studied in terms of copper recovery. The results show that the flotation of coarse particles is feasible using seawater without frother

Jan 1, 2020

By T. Steyn, M. Fofana

"One of the most important performance indicators of a dense medium cyclone (DMC) circuit is the Tromp curve, and by extension the separation density and Ecart Probable (Ep) values. The densimetric profiles of DMC product streams have been traditionally acquired using heavy liquid sinkfloat analysis, which has certain disadvantages, such as the associated safety and health risks. More recently, non-toxic media such as lithium hetero-polytungstates (LST) have been used, with the desired densities being achieved by maintaining the solutions at specific temperatures. However, the high costs of these liquids can be prohibitive. The long turnaround time of the sink-float analysis is a further disadvantage for timeous interventions to the operating set-points of the DMC process.The RhoVol technology can generate the density distribution of a batch of particles in a rapid, accurate, repeatable, and safe manner. Additional data of interest, such as particle size and shape, are also measured and reported on a per-particle basis. Furthermore, samples can be sorted into discrete sorting bins based on any of the measured parameters of the particle, making further analyses of the material possible.This technology has applications across all commodities that use the DMC, particularly in the size fractions –25 +8 mm and –8 +3 mm. To date, laboratory results have proved very encouraging – separation densities are within 5% of traditional sink-float results, and the technology is being introduced to diamond DMC plants. IntroductionDense medium separation is a commonly applied beneficiation technique for the density separation of valuable products from crushed ores. The industrial applications of dense medium separation have been summarized and reviewed by various authors (Scott and Napier-Munn, 2000; Bosman, 2014; Napier- Munn, 2018). Dense medium cyclones (DMCs) are widely used in the coal and diamond industries to produce clean coal or to preconcentrate kimberlitic ores, respectively. Cyclone performance (separation density monitoring) techniques are varied. In the mineral industry. Density tracer tests (Napier- Munn, 1985, 2014; Davis, Wood, and Lyman, 1985) without mineral material, are widely used, although their accuracy in predicting operating cut-points becomes limited once mineral material is introduced. More recently, radio frequency tracers have been also used for the determination of cyclone efficiency (Partition Enterprises, 2017)."

Feb 1, 2019

By J. P. Garnier, T. Bhambhani, J. A. Garcia, N. Renaud

Most flotation plants use a static reagent scheme, i.e., a set combination of collectors, frothers, and modifiers. This scheme is usually developed and refined over time to deliver optimal (not necessarily the highest) performance when the major ore types are fed to the plant. However, when ore types or mineralogy coming to the plant change substantially (and this often happens as different areas of the pit(s) are mined and crushed at the same time), there are upsets in the process, typically leading to lower recoveries. Adapting to this variability is usually done only when performance drastically suffers, and the changes made may be too late and bring additional variability in performance. The premise for SmartFloat™ is that the reagent suite needs to be dynamic, adapting continuously to changes in the ore and operating conditions. Solvay has combined advanced analytics and data science techniques with its expertise in flotation reagent chemistry to systematically and automatically achieve the above, and in real time. Thus, SmartFloat™ is optimizing the reagent suite continuously, removing the additional variability created by belated human interactions resulting in a better and more stable process. In addition, this advanced approach allows for continuous improvement by identifying poor performing ore domains and improving the reagent suite using Solvay’s FM-100 approach to design appropriate solutions.

Jan 1, 2023

By G. R. Baiden

Introduction The introduction of teleremote systems to underground mining can provide a significant improvement in the performance of a mine when compared with conventional mining techniques. This paper presents the concepts of teleremote mining in a case study showing how the systems work and the competitive advantage autonomation of mining techniques will provide for underground metal mining operations into the future. This paper is divided into two sections: the Mining Automation Program and What is next? On January 1st 1996 Inco Limited, Tamrock Oy, DYNO Explosives Group and CANMET formed a consortium for the development of teleremote mining equipment called the ‘Mining Automation Program’ or MAP. This program included a five-year research and development agreement that combines the talents of the above organizations to create mining equipment and systems for autonomating mining. The projects are based on the communication system currently sold and marketed by Automated Mining Systems Limited. The main components of the program investigated the development of a positioning and navigation module, autonomated systems using teleremote techniques for development and stoping, and software systems to support the use of this equipment. The program included the establishment of a test mine, at Inco’s 175 Orebody near Copper Cliff North Mine. This facility was unique allowing collaboration of companies and research organizations inthe design and testing of techniques and equipment used to apply autonomation to mining. Since the inception of the project other research alliances have been added to enhance the program. These include the application of ground support (Meyco/ Master Builders), muck pile recognition, the broadening of telecommunications links (PRECARN Associates Inc.-MALTA project) and the collection and processing of drilling core through the automated diamond drilling project (J.K.S. Boyles). MAP began as an idea a number of years ago with the fundamental question ‘Can an ore-body be profitably mined through autonomation?’ The concept was to design mining equipment and systems that would allow the teleremote operation of a mine. Automation was only one componentof this much larger teleremote mining issue. To start with, it was essential to prove or disprove the feasibility of this concept. The fundamental requirements are: • Telecommunications • Positioning • Navigation • Equipment • Software • Electronics • Mining Engineering • Organization. Each of these had to be considered. Technically, the feasibility of the project hinged on the successful development of a high capacity communication network, an accurate underground positioning system, a navigation system and finally the electronics and software that could integrate these. Mining equipment that could perform all the mining functions was the next requirement, along with explosive supplies that could be delivered to the holes teleremotely. Whatever the systems developed, they must be able to work in both bulk and selective mining situations and in varying conditions within a mine. Finally, the organizational issues of a change from our current method of operation to teleremote mining had to be understood. After five years of research and development the answer to the question ‘Can an orebody be profitably mined using autonomation techniques?’ is YES! There are still hurdles to overcome, however, the basic premise has been proven. The development and production of underground tunnels and stopes has been done. There have been interesting outcomes in terms of reduced effort to accomplish mining and the total time to mine. Definitions •Automationis the process by which a machine or system is run continuously including the ability for the system to self-correct. •Autonomationis the same as automation except that the process does not self-correct. •Teleremote operation is the operation of mining equipment over a network from any location out of line-of-sight of the machine. •Equipment Automationis the addition of technology to a machine that allows for unmanned operation of a machine and thus enhances the productivity of the operator. For example, a guidance system that allows a load-haul-dump to drive by itself, thus freeing the operator for other tasks. •Teleremote mining describes a mine process that combines the use of teleremote operation (potentially with some automation), positioning and process engineering, monitoring and control. •Tamrock DataSoloTMis a computerized drilling rig as shown in Figure 1. •Tamrock DataMini™ is a computerized development drill rig used for drifting and construction tunneling as shown in Figure 2.•Tamrock Toro 450™ is a LHD (Figure 3).

Sep 1, 2001

By I. Silin, H. Wotruba, A. Liono, I. Volobayev, Y. Rubinstein, D. Gürsel

Old, abandoned or in situ processed and storaged tailings can be a potential source of remained valuable metals and minerals. By reprocessing of tailings, it is possible not only to achieve economical profit from recovery of valuable metals, but also to reduce environmental damage caused by tailings such as generation of acid mine drainage from sulfide minerals, mobilization of heavy metals, soils and groundwater contamination. In addition, storage facilities can be successfully redesigned with modern geotechnical requirements and monitoring to avoid a dam collapse of abandoned tailings. In this case study, the processing of low grade abandoned tailings was investigated. Copper (0.15%), cobalt (0.032%) and gold (0.35 ppm) were determined as main valuable and recoverable metals. Cobalt occurs as cobaltite and cobaltiferrous pyrite, while chalcopyrite represents copper. The fine fraction of tailings below 32 μm is enriched with cobalt and copper. Preliminary test-works with initial tailings sample were aimed to recover copper, cobalt and gold. The previously tested magnetic and gravity separation could not recover the metals in a pre-concentration step. Flotation tests of the tailings sample had shown a suitability for flotation without previous regrinding of the tailings. The valuable minerals are first proposed to be recovered by collective flotation, followed by a selective circuit with production of a low grade copper concentrate and a cobalt bearing pyrite concentrate. Based on various tested collectors, amounts of sulfidisation agents and activators, a suitable reagents regime was determined and used for up-scaling by locked cycled test. Keywords: reprocessing, tailings, copper, cobalt, gold, flotation, cobaltite, cobaltiferrous pyrite

Jan 1, 2020

By Oaitse Medupe

The feed to the BCL concentrator is made of the ore from Phikwe No3 shaft, Selebi shaft and Selebi North shaft. The receiving bin of the concentrator has daily throughput of 7869mt live capacity of ore with feed grade from underground operation of 0.70%Ni, 0.75% Cu and 0.05% Co. The valuable minerals in the ore are Pentlandite, Chalcopyrite. Cobalt is present mainly in the solid solution in pentlandite. The common non-sulphides minerals are Amphibolites, quartz, micas, and Feldspar while pyrite and pyrrhotite are the major gangue sulphides. Pyrrhotite contains between 0.1% and 1% Ni in solid solution. From the mineralogical investigation, it was found that approximately 65% of the pentlandite in the ore occurs as exsolutions in the pyrrhotite and the grain sizes ranges from 8 to 38µm. about 25% of the nickel bearing pentlandite is medium grained and subhedral. This kind of pentlandite occurs along the cracks of pyrrhotite or as inclusions in pyrrhotite. The rest of pentlandite present is disseminated in the gangue matrix. Because of the fine occurrence of pentlandite, fine grinding was conducted in order to improve the recovery as well as the concentrate quality. A series of subsequent flotation test were performed in order to evaluate grinds of 35, 40, 45, 50, 60 and 80% passing 75µm. It was observed that ? The mass pull increased together with increasing fineness of grind ? Similar nickel recoveries were obtained at 35 and 40% passing 75µm but from 50% and 60% the grind was seen to adversely affect the nickel recovery. At 80% passing 75µm the recovery increased by small amount. ? Flotation kinetics showed higher initial nickel recoveries but these did not translate into higher final recoveries. ? Grinding finer than 80% passing 75µm yield very high grades of the concentrate in the first minute of the flotation test, and the grade is dramatically reduced in the fifth minute of the test. It was concluded that the current grind of approximately 48% passing 75µm is close to the optimum and no significant benefit were found to be associated with finer primary grinds. The inconsistence of the grade and recovery as well as the pentlandite losses will be discussed. Keywords: Pentlandite, Nickel losses, Grain size, Flotation

Jan 1, 2007

By C. B. van den Berg

n this study, silver and palladium nanoparticulate inks with different metal-binder ratios were screen-printed onto a paper substrate. The printed layers comprised the metal nanoparticles and an ethylcellulose binder. The layers are not typical metal composites due to the low concentration of binder and high porosity. The electrical sheet resistivity of each particle concentration was measured, and the data fitted using the scaling law of percolation theory and the general effective media (GEM) equation. The percolation parameters, i.e. the percolation threshold and the critical exponent, for each system were determined from the fits and compared. The percolation threshold for the palladium layer (39.8 wt%) was lower than that found for the silver layer (44.9 wt%). The critical exponents determined for the palladium and silver layers were both lower than the universal value for three-dimensional percolation systems. Microscopy observations indicate that the difference in the percolation threshold for the two layers can be attributed to variations in their microstructure.

Jan 1, 2014

By M. F. Dawson, S. B. Davis

SYNOPSIS This paper describes the size reduction of limestone smaller than 1 mm by attrition grinding, using quartz (1 to 3 mm) as the grinding medium in a laboratory rig. The ore and grinding medium were closely sized fractions, and the particle size of the grinding medium was at least three sizes larger than that of the ore. Batch tests showed that the size reduction of the feed followed two first-order rate processes: one for an apparently fast-breaking ore fraction, and a slower one for most of the ore (86 per cent). The production of fines (material smaller than 10 µm) followed a zero-order rate equation. Continuous runs showed that the process could be modelled as a perfectly mixed system provided that the discharge screen did not selectively retain coarser particles of ore. The ratio of medium to ore (both by mass and by volume) was found to have a significant effect, the most energy¬efficient grinding occurring at ratios between 1 and 2. The solids content of the slurry also had a significant effect, the greatest efficiency being obtained at 50 to 65 per cent solids (by mass). Within these energy-efficient ranges of medium-to-ore and solids content, the lower values resulted in maximum feed breakage and the higher values in maximum fines production. The most important factor in the breakage of feed was the difference in the particle size of the grinding medium and the ore; the amount of ore broken out of the feed size for a given energy input was found to increase linearly with the difference between the size of the grinding medium and that of the ore up to 2 mm. The production of fines increased similarly, but only up to a difference of about 1,2 mm, when it levelled off at about 5 kg/kW ? h. The mechanism proposed for attritioning is mainly the abrasion of 1 µm planes of limestone along the crystal axes, with some fracturing along existing lines of weakness. The energy consumption of nearly 200 kW ? h per ton of product smaller than 10 µm appears to be higher than that in other types of milling. It is concluded that the value of attrition milling lies in its selectivity; in this work, only the softer limestone and virtually none of the hard quartz grinding medium was comminuted.

Jan 1, 1989

By I. Serepa, N. C. Steenkamp

Investigations were conducted to determine the condition and stability of the existing decline at amine in the Kalahari Manganese Field, Northern Cape Province, South Africa. During the inspection of the decline, voids were identified behind the concrete lining on the hangingwall and sidewalls over a total linear distance of 230 m. The voids did not provide confinement and, as a result, self-mining was occurring behind the lining. Water was flowing into the decline, over a total linear distance of 100 m, at areas where the decline intersected incompetent rock units, causing softening of the concrete lining and deterioration of the surrounding rock mass. Further damage to the concrete lining was caused by expansion and contraction of the wet red clay unit. Remedial work comprised void filling and water sealing to prevent further deterioration of the decline and ensure that it remained operable for the remainder of the life of mine. Void filling was accomplished by drilling rows of holes along the decline to access the voids and filling the voids with foam. This was followed by the sealing with polymer fluids. Telescopic pipes were also installed to allow water to drain off. A visual inspection was conducted and check-holes were drilled to assess the quality of the remedial work. The void filling material had penetrated cracks in the concrete lining, and areas where voids were intersected by check-holes were re-filled. Additional holes were drilled to re-seal areas that were still wet. The remedial work was completed successfully, as all voids were filled and stability achieved without compromising the concrete lining. The ingress of groundwater was also reduced to some residual dampness.

Mar 2, 2022

By J. T. M. Amphlett, C. A. Sharrad, M. D. Ogden, R. I. Foster

"A renewed interest in nuclear power around the world in order to reduce greenhouse gas emissions is going to increase demand for uranium as fuel. This will result in more uranium being mined, which will in turn increase associated environmental pressures, such as fresh water use. A move to lower quality waters containing impurities such as chloride would help alleviate these pressures. In this work, we determined the uptake characteristics of weakly basic anion exchange resin Ps-EDA towards uranium from saline solutions in a dynamic flow column. Breakthrough curves were produced, with suppression of uptake being observed for chloride concentrations above 5 g L-1. Calculated resin saturation capacities at zero and 5 g L-1 chloride are comparable with literature values for strong-base anion exchange resins, and exceed those published for weak-base resins up to 20 g L-1 chloride. Data has been fitted to multiple breakthrough models, with the modified dose-response model most effectively predicting uranium recovery. The results show that the ethylenediamine functionality could be suitable for use in future uranium processing flow sheets where a high-saline lixiviant is used. IntroductionIon exchange (IX) is a key technology in the uranium mining industry and is well established for the extraction of uranium from both acidic and alkaline leach liquors (Edwards and Oliver, 2000). It was first employed in 1952 at the West Rand mine in South Africa (Ford, 1993; Taylor, 2016). H2SO4 and Na2CO3 are the most commonly employed lixiviants used to solubilize uranium in acidic and alkaline leach conditions respectively. The chemistry of these systems causes uranium to form anionic sulphate or carbonate complexes, which can be taken advantage of by anion exchange resins.Another major technology for the extraction and purification of uranium from leach liquors is solvent extraction (SX). This technique involves the extraction of uranium from the aqueous phase into an immiscible organic layer. Although this is a commonly used method, there are major drawbacks to it, including the use of large volumes of flammable solvents, solvent loss, phase disengagement, third phase formation, and the production of problematic degradation products (Veliscek-Carolan, 2016). These problems can be circumvented through the use of IX resins."

Dec 1, 2018

By J. Jacob

Diamondiferous linear beaches in Mining Area No. 1 have been the mainstay of Namdeb?s diamond production for more than 80 years. Most of the onshore beaches have been mined out, but in recent years mining has been extended offshore into the surf zone through a process of beach accretion. A total of 61.6 million carats has been produced from the gravel beaches since their discovery in 1928, and Mining Area No. 1 is considered to have great remaining potential from areas currently submerged under water. To date, the surf zone has remained largely unexplored due to the consistently strong winds, currents, and large waves which make access to this area extremely difficult. This paper describes the processes used in developing a practical methodology for exploration of the surf zone in a domain extending approximately 22 km long in a northwest?southeast direction and 0.3 km wide in a perpendicular direction adjacent to the current Mining Area No 1. The vigorous surf zone poses multiple technical challenges in terms of obtaining geological and diamond information. In order to access the area for sampling, a jack-up walking probe drill platform (PDP) with a 5-inch diameter reverse-circulation drill has been developed to carry out exploration drilling in the dynamic surf zone. The hydraulically driven platform has eight legs, each of which is 18 m long. Four of the legs are in fixed positions on the fore and aft sides of the platform. The other four moveable legs are fitted to sliding frames attached to the port and starboard sides of the platform. The sets of fixed and moveable legs can be raised and lowered by hydraulically powered jacking stations. By alternately lifting and lowering the sets of fixed and moveable legs in conjunction with the frames moving back and forth horizontally, a walking action is performed by the PDP. The platform can walk at a speed of 10?15 m/h, depending on weather and footwall conditions. Optimization of sampling for diamondiferous gravel occurrence in Mining Area No.1 was undertaken through creation of a virtual orebody on which different sample configurations were tested. The input data for the construction of a virtual orebody comprises a set of drilling data, collected from recently accreted areas directly adjacent to the 22 km × 0.3 km target domain. The input drilling data covers only 34% of the domain, and for the purpose of this study, a single realization is deemed to be sufficient. The texture obtained from using only the drilling data to construct a simulation did not make geological sense; hence it was necessary to make use of analog data in order to improve the simulation. The first analog data used consists of the gully patterns found in the metasedimentary Precambrian bedrock footwall. Gullies are, in general, gravel filled and it is fair to assume that gully patterns form a subset of the total gravel occurrence. Total gravel occurrence includes marine terraces (governed by sealevel stands) above bedrock peaks, together with gravel within gullies below bedrock peaks. The second analog ?data? introduced is through the use of ?expert interpretation?. The indicator drilling data is interpreted by expert opinion and the 2-dimensional result is hand-sketched, digitized, and then pixelated. The pixelated data set is then used as input for variogram calculation. This study cannot provide a single definite optimization result as the nature of the data does not permit this. The use of different validation approaches (conditioning data, where available; expert interpretation; and gully pattern data), however, can give a very good indication of how to balance sampling effort with de-risking aspects related to geological continuity. Work undertaken by sampling the simulation will give an assessment of the relative probabilities of determining gravel occurrence in the study area. This study showed that a 50 m × 400 m cross-configuration will be a good initial sample spacing for highlighting areas where gravel may be absent, and further infill drilling may be required. The relative efficiency of a 50 m × 400 m cross off-set sampling configuration has been demonstrated using a trumpet curve versus sampling effort when using kriging as the estimation method. Keywords sampling configuration, marine diamonds, orebody simulation.

Jan 1, 2014

By L. Tartibu, S. Assuli, P. Nkul, A. Kabimba, W. Elongo, N. Makhotla, D. F. Verwey, F. G. Ndiitwani, J. Bilali, T. Mukongo

The presence of colloidal silica negatively impacts various hydrometallurgy processes. This paper details the nature of colloidal silica, operational issues caused by colloidal silica, as well as various mitigation measures. MMG Kinsevere observed severe phase-continuity instability, increased crud formation, and reagent consumption, and reduced current efficiency in electrowinning with a deterioration in copper quality. Historical mitigation measures were initially implemented but failed to solve the problem. MMG Kinsevere successfully achieved efficient silica removal without adverse effect on the solvent extraction with the use of DEHSCOFIX® SC12 coagulant. A week into the coagulant trial, silica concentration had dropped from > 1500 mg/L to within 500 mg/L. The solventextraction plant recovered its stability and again operated at maximum capacity. Additionally, improvement was observed on current efficiency and copper cathodes quality with use of the coagulant.

Jan 1, 2023

By D. M. Poulter, J. N. Brooke, P. H. Williams

"The complexity of the mining and metallurgical operations of Nchanga Consolidated Copper Mines, Limited, has made it necessary to use computer-assisted planning techniques in order to maximize copper production and marginal contribution to profit. The most successful of the Group Production Scheduling systems utilized linear programming to optimize the concentrate routing only. This third-generation system was commissioned in March, 1968.It bad become necessary by March, 1970, to expand the long-term planning activities and to take into account new mines and new concentrate treatment schemes. Technical difficulties and manpower limitations made it impossible to expand the third-generation system, and it was decided to construct a new Group Production Scheduling system using only linear programming.The plant models in the new fourth-generation system are based on data available from the monthly reports of the metallurgical plants. The models consist of mass balances and empirical relationships. Matrix coefficient assignment and management reports are produced using a Report Generator Language designed for linear programming data files. The development of this system is an example of a user application of a system package."

Jan 1, 2014

The following contributions were received to the paper entitled 'Safety in South African mines: An analysis of accident statistics', by H.S. Eisner and J.P. Leger, which appeared in the J. S. Afr. Inst. Min. Metal., vol. 88, no. 1, Jan. 1988, pp. 1-7. Contribution by H. WAGNER* The paper by Dr H.S. Eisner and Mr J.P. Leger is critical of the safety situation on South African mines and portrays the industry as having little concern for the health and safety of its workers. Moreover, the casual reader gains the impression of deliberate misinformation by the industry to the public concerning safety maters. Furthermore, certain socio-economic reasons are advanced for the apparent differences between the fatality and injury rates reported for coal mines in South Africa and those for the United Kingdom. Contribution by S.A. WATTS. Authors Eisner and Leger are to be commended on their paper, which highlights, according to their interpretation, various shortcomings of both the Chamber of Mines accident statistics and those published by the Department of Mineral and Energy Affairs. Authors' Reply We gratefully acknowledge Dr Wagner's contribution to the discussion on our paper. For convenience, we shal use his sequence of comments in our reply. Before doing so, however, it may be useful to explain how our paper came to be written. After the explosion at Hlobane Colliery in 1983, one of us (HSE), in February 1984, was retained by the lawyers acting for some of the dependants of the victims to advise on technical maters relating to the explosion. Contribution by Ms S.A. Wats Some of the points made by Ms Wats have already been answered in our comments on Dr Wagner's contribution. We are fully aware that the number of accidents leading to absences of less than 4 days would be much greater than shown in our bar chart, and are grateful to Ms Wats for drawing attention to the specific exceptions that can make a 1-3 day accident compensable and that are clearly responsible for the relatively low count in that category of the chart.

Jan 1, 1988

By A. Santana, J. Jankolovits, G. S. Reyes

The flotation of sulfide ores that contain carbonaceous gangue requires significant operational and chemical intervention to achieve suitable metallurgical outcomes. Carbonaceous gangue dilutes concentrate grades, alters the froth behaviour, reduces operational stability, adsorbs reagents, and reduces value recovery. Carbon management processing strategies like preflotation and depression are often presented as point solutions. Moreover, oversimplified mechanisms of carbon depressants belie their complex and nuanced impact on flotation behaviour. Optimising the flotation of carbonaceous sulfide ores requires a holistic consideration of interactions between the carbon management reagents and the processing strategy, ore mineralogy, flotation behaviour, flowsheet, and all other aspects of the flotation system. Examples are shown where conventional, simplistic mechanisms of carbon depressants fail to explain the observed flotation behaviour. The multifaceted impacts of carbon depressants on froth behaviour, collector performance, and value recovery highlight the need for a holistic approach to carbon management. Keywords: Carbon management, carbonaceous ores, sulfide flotation, carbon depressant

Jan 1, 2020