Search Documents

By Andrew A. Cochran

Laboratory-scale research was conducted by the Bureau of Mines to develop a new process for treating electroplating and other wastes. Various acid and alkaline cyanide wastes were combined under controlled conditions to neutralize the wastes and to almost completely precipitate the metals and cyanides. The metals were subsequently recovered for recycling; the cyanides can also be easily recycled. The process was successfully used to treat the major types of electroplating and etching wastes, containing Cd, Cr, Cu, Ni, and Zn, and to treat both concentrated and dilute wastes. The economic aspects of treating concentrated electroplating, etching, and anodizing wastes are especially attractive because of the low cost of mixing two wastes, the high value of the recovered metals, and the simplicity of the recovery procedures. The filtrates from the waste-plus-waste step were relatively harmless compared with the original wastes and met Public Health Service standards for free cyanide content. Free cyanide ions were not detected in most of the filtrates; the limit of detection was 0.03 ppm. Only small amounts of HCN were produced during the neutralization; the HCN was collected and neutralized.

Jan 1, 1974

By Floyd D. Everett

The J. B. fluorite deposit is in the Washington mining district, southwestern Beaver County, Utah (fig. 1). Fluorite outcrops were found during 1942, and three lode claims wore located. Little work was done on the property until October 1943, at which time the Bureau of Mines started development to determine the subsurface extent of the fluorite mineralization exposed at the surface. The most prominent rocks in the J. B. mine area are porphyries, which vary considerably in composition. Dacite porphyry appears to be the most common host rock for the fluorite-quartz-calcite lenticular masses. The dacite porphyry in the area is highly brecciated over a strike length of more than 1 mile. Fluorite deposits in the brecciated zone cover a strike length of approximately 400 foot. The fluorite lenses range in length from 40 to 200 feet and in width from 4 to 10 feet (fig. 2). The Bureau of Mines work on the J. B. property was started in October 1943 and completed in October a year later. The work consisted of surface trenching by bulldozer and hand methods, shaft sinking, drifting, and crosscutting. Eleven trenches totaling 1,800 linear feet were excavated. An inclined shaft was sunk to a depth of 105 feet, and from thin shaft 577 feet of drifts and crosscuts were driven to outline the extent of the mineral deposit (fig. 3). Two hundred ninety-seven samples were taken in the surface trenches and underground workings. The locations of the samples and analyses arc shown in accompanying figures and tables. Results of metallurgical tests comprise the concluding section of this report.

Jan 1, 1950

By E. A. Johnson

The Bureau of Mines determined the effect of slag additives on copper solubility and the distribution of typical impurity elements between copper-iron matte and silica-saturated fayalite (iron silicate) slag at 1,250° C, in CO-C02 atmospheres with 10 pct S02. Small additions (<10 pct) of CaO, A1203, and MgO were shown to decrease copper solubility in the slag. Additions of CaO increased the solubility of bismuth and tellurium in the slag at lower matte grades. Al 20 3 additions decreased the solubility of tellurium in the slag, but increased that of bismuth at lower matte grades. A1203 additions increased the solubility of both at lower matte grades. With no additives, matte grade did not affect the solubility of bismuth in slags, whereas increasing matte grade resulted in a slight decrease in the tellurium solubility in slag. Additions of CaO or As203 alone to the slag increased selenium and arsenic distribution to the matte, but had little or no effect on antimony distribution; whereas small MgO additions decreased antimony distribution to the matte but had no effect on arsenic and selenium distribution. In slags with no additives, selenium distribution to the matte increased with increasing matte grade, while that of antimony decreased and that of arsenic was unchanged.

Jan 1, 1982

By Floyd G. Anderson

The Federal Bureau of Mines promotes the use of safe and effective dust-collecting devices for rock drilling in coal mines. To insure that such devices are available to the coal-mining industry, the Bureau issues certificates of performance for dust-collecting systems and certificates of approval for dust collectors and rock drills or other mining equipment with integral dust-collecting systems that meet the requirements of an established Schedule.4/ Investigations are conducted under the provisions of the current revision of this Schedule by engineers of the Branch of Health Research. This circular describes briefly the requirements and procedure for obtaining certificates of performance or approval and lists equipment that has been certified as permissible under Schedule 25 or its revisions as of January 31, 1961. The names and addresses of companies to which certificates have been issued are listed alphabetically at the end of this circular.

Jan 1, 1961

By N. F. LeJeune

[ ]

Jan 1, 1924

By W. J. Fullerton

This paper is one of a series prepared for the United States Bureau of Mines discussing the methods used in crushing and grinding materials for cement manufacture, and deal particularly with the methods used at the Howes Cave plant of the North American Cement Corporation. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1932

By Stanton L. Tainter

"As an adjunct to its minerals-investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the supervision of J. H. Hedges, chief, Tucson Branch Mining Division, and under the general supervision of Lowell B. Moon, chief, Mining Division, reports upon certain methods devised to overcome difficulties encountered in cementing of diamond-drill holes at a Bureau of Mines project at Christmas, Gila County, Ariz.Pressure grouting was employed to recondition a caved hole it was desired to reopen and deepen. The hole, which had boon stopped 7 months previously at a depth of 488 feet, was caved below 449 feet in a contact zone of claylike, altered diorite and crumbly metamorphosed limestone. As other means of obtaining moderate pressure were not available, carbon dioxide gas, drawn from tank of liquid carbon dioxide through a pressure reducing and regulating valve, was used. The hole was reopened successfully with 12 grouting jobs.Another hole, where cawing from several water-bearing fractures between 202 and 232 feet gave trouble, was successfully cemented by the use of a grouting plug. An attempt to cement through the rods had failed, owing probably to agitation caused by water currents. Pressure grouting through the caning set above the cave could not be need, because water was forced up outside the casing when pressure was applied. The problem was solved by using a wooden plug 1-13/16 inches in diameter, which, when soaked in water, expanded to a tight fit in an AX hole. A hole was drilled through the plug, and a rubber flap valve was nailed to the lower end. In the upper end of the plug the hole was enlarged to fit loosely over an EX rod coupling finished smooth. The plug was lowered on the end of the drill rods to a point about 10 feet above the cave, where it was allowed to expand tightly to the hole. Cement grout was then pumped through the rods, and the rods were removed from the hole. After allowing time for the cement to set, the wooden plug was chopped out and drilling van resumed.Over 300 tests were made to determine the type of cement most suitable for use on the Christmas job, and the effect of cement-water ratio, temperature, and various admixtures on workability, setting time, and strength. The results of these tests, described in detail in the body of this report, indicate the desirability of thoroughly testing available cements when it is necessary to drill holes under difficult conditions that may cause failure.When it became desirable to reopen and deepen a caved drill hole, it was considered easiest to recondition the hole by pressure grouting, As other mans for obtaining moderate pressure were not available, a method utilizing carbon dioxide gas was employed. The hole was reconditioned successfully with 12 grouting jobs."

Nov 1, 1949

By P. C. Good

High-purity chromium was prepared in massive form by the electrolysis of chromium trioxide solution at high temperatures. The metal thus obtained, containing 50 to 150 p.p.m. of oxygen, 20 p.p.m. of nitrogen, and traces of metallic impurities, could be hot-worked to rod and sheet and drawn to wire ductile at room temperatures. Optimum concentrations and operating conditions were established for the deposition of chromium from chromic acid baths containing sulfate, fluoride, and silicofluoride ions. Current efficiencies of 13 percent were attained with baths containing sulfate ion, and efficiencies of 40 to 44 percent with baths containing fluoride and silicofluoride ions. Cation exchange resins were used for removing metallic impurities from chromic acid solutions containing sulfate ion; solutions containing fluoride and silicofluoride ions were purified by recrystallization.

Jan 1, 1960

By Welby G. Courtney

The Bureau of Mines conducted an exploratory field survey to determine the amount of airborne coal dust, the size distribution of the dust, and the rate of dust deposition in coal mine airways. The survey was taken at eight underground locations in operating coal mines. The rate of dust deposition in the airways depended upon the concentration of air-borne dust and decreased exponentially with distance from the dust source. The rate was seemingly independent of the size of the airborne dust particles. The rate of deposition, along a return, for the coal dust from a fade being mined with a continuous mining machine closely matched the rate for the rock dust from a trickle duster. A sample rock-dusting schedule for that return is presented; that is, the trickle duster should be operated for 3-112 hours after every five shifts to protect the average deposit of new float coal dust in the return, but operation after every three shifts is preferred, to protect an occasional heavier deposit.

Jan 1, 1982

By W. W. Odell

The results of the 1921 cooperative experiments conducted by the U. S. Bureau of Mines and the University of North Dakota at the University mining substation plent at Hebron , North Dakota , pointed clearly to certain definite dep ficiencies in the schemes hitherto developed for benefiting and utilizing lignite . First The apparatus used in the carbonizing process or used to produce carbonized lignite suitable for briquetting is too costly , that is , the cost per ton day of residue made is too high . Second - The depreciation of the carbonizing appara tus is too high . Third The carbonizing apparatus can not be operated intermittently without seriously damaging it and impairing its efficiency of performance . Fourth Too little attention has been given to the possibility of using at least a certain percentage of the carbonized lignite directly in suitable stoves and furnaces without briquetting or other treatment . Accordingly , consideration was given to the design of an oven that could be built at a mine without the importation of highly skilled and specially trained construction men , erected at a low first cost , readily kept in a state of repair , operated at a rela tively high capacity and put into operation or shut down at will without seriously damaging the brickwork . The need of such an oven was appreciated also by the University of North Dakota and a cooperative agreement was made to build and operate such an oven during the summer of 1921.

Feb 1, 1923

By Irving Hartmann

1. Under the conditions of the tests described herein, the proper use of an incombustible stemming plug of the type discussed prevented ignitions of gas in all tests during the firing of 21 single shots of permissible explosive in cool. In two tests with multiple blasting (four and five shots each) no ignitions resulted. 2. The results of a few tests in this investigation and of numerous tests made previously indicate that fire-clay stemming of the same weight as an incombustible plug provides about the same degree of protection as the plug against gas ignitions during blasting of coal by permissible explosives. 3. The hazard of gas ignition on firing charges of non-permissible 40-percent gelatin dynamite in coal was reduced but not eliminated when the shot holes were stemmed with one or two incombustible plugs or with an equivalent weight of fire clay. 4. On the basis of this investigation, the Bureau of Mines considers the proper use of incombustible stemming plugs of the design tested, under the conditions of the tests described in this paper, to be of equivalent safety as the same weight of fire-clay stemming. This report does not constitute approval or disapproval of the incombustible stemming plugs by the Bureau of Mines. 5. The test data indicate that misfired charges in shot holes stemmed with the incombustible stemming plug cannot be disposed of with certainty by the procedure recommended by the manufacturer. In this investigation the misfired charges failed to detonate in 30 percent of the trials.

Jan 1, 1950

By Lewis V. Wade

This report provides background information concerning a mine roof simulator currently being considered by the Bureau of Mines. The simulator is a mechanical device with the ability to simulate the forces and displacements associated with mine roof over an area 20 by 20 feet. The topics covered in the report include a conceptual description of the system, definition of system capabilities, discussion of how such capabilities were decided upon, description of available control modes, and a comparison between the mine roof simulator facility and similar facilities existing elsewhere.

Jan 1, 1974

By M. S. Oudenhoven

This Bureau of Mines investigation was conducted to obtain an experimental solution of stress changes in the vicinity of a circular opening in an infinite plate. Plates were stressed biaxially in compression and subjected, by four different-length shoes, to a uniform pressure at opposing points on the opening periphery. The principal stresses along the vertical and horizontal axes, which result from peripheral pressure, were obtained from the photoelastic analysis of four frozen-stress epoxy models. These principal stresses were then super-imposed on the mathematically determined principal stresses (along the same axes) obtained from a theoretical biaxial stress field in which the magnitude of the lateral pressure was one-third that of the vertical pressure. The results indicate that an increase in shoe length increases the radial compressive stress and the tangential tensile stress (except tangential compression at r/a = 1, which exists for all shoe lengths). Also, a partial control of the stresses within one-half radius of the opening surface is accomplished by a change in the magnitude and placement of peripheral pressure.

Jan 1, 1966

By L. C. Karrick

The Bureau of Nines has received many inquiries on the subject of assaying oil-shales, both from individuals who desire to wake their own assay while in the field, and also from Commercial assayers and investigators. The present paper describes the assay retort used by the Bureau of Mines. in the research work on oil-shales now in progress at the Intermountain Experiment Station of the Bureau at Salt Lake City, Utah, and at the Colorado cooperative oil-shale laboratory, Boulder, Colorado. This retort, which was developed through experimentation in the bureau&apos;s laboratories, has been found to be convenient in use and. capable of yielding reproducible results. M. J. Gavin, Oil-Shale Technologist, gave valuable assistance in preparing the subject matter for publication and made many helpful suggestions during the experiments made by the writer in the course of the development of the assay retort. L. A. Anderson, research "fellow" University of Utah, assisted in the preliminary development of the assay retort.

Jan 1, 1921

By Byron S. Gottfried

This Bureau of Mines report presents a method for combining the distribution curves at different specific gravities of separation, for a given piece of coal-cleaning equipment and a given raw coal feed, into a single, generalized distribution curve normalized with respect to specific gravity and, therefore, independent of the specific gravity of separation. Illustrative generalized distribution curves, based upon Bureau of Mines collected data on industrial operations, are presented for five different types of coal-cleaning equipment. The well-known concept of probable error is extended to the generalized distribution curve. It is shown that the conventional probable error is directly proportional to the specific gravity of separation. A number of sample calculations, illustrating the use of the generalized distribution curve and generalized probable error, are presented in the appendix.

Jan 1, 1977

By W. O. Philbrook

Reduced-scale models have long been used in hydrodynamics, aerodynamics, and heat transfer for studying fundamental flow relations or the performance of prototype designs under prescribed conditions. The pilot plant is a common tool of chemical engineering for investigating process variables and as an integral step in developing a new process. The metallurgical industry was rather slow to recognize the applicability of these techniques to some of its established and rather complex processes, but there has been a rapidly increasing number of applications of the principles of modeling in process metallurgy since World War II. Not only have pilot-scale operations been employed for developing methods of extracting metals that have recently achieved commercial importance, as well as new processes for some of the commoner metals, but models have also been used for engineering studies aimed at better understanding of the controlling, variables of time-honored conventional processes, It appears that the principles of similitude have become accepted as a useful tool, when properly applied, in metallurgy as in other fields of engineering. Much of the work of the Pyrometallurgical Laboratory, Region V, involves study of high-temperature smelting and refining processes for ferrous and related metals in pilot-scale equipment, such as the experimental blast furnace, converter, open-hearth, arc furnace, and rotary kiln. It was appropriate for the work of this laboratory that guiding principles for designing apparatus and interpreting results should be set down and that a bibliography of related work should be available for reference. A summary of the principles of model study and a brief review of some of the more noteworthy general papers have been published elsewhere.3/ Also, the Bureau of mines plans to publish a report of investigations describing its experimental work in this field. The bibliography is presented here as a service to others who may have use for it.

Jan 1, 1958

After nine years of negotiations, the U.N. Conference on the Law of the Sea approved a Law of the Sea Treaty text in April. Israel, Turkey, the United States and Venezuela voted against the text and 17 other nations including Belgium, the Netherlands, Italy, the Soviet Union, the United Kingdom and West Germany abstained. These nations still have the option of joining the treaty when it is opened for signing in December. However, the Reagan Administration has stated that several provisions of the deep seabed mining portion of the text are unacceptable and it seems unlikely that the United States, at least, will change its position. ALUMINUM Reynolds Metals Co. has criticized an Oregon state plan to relax air pollution standards for aluminum plants. The company feels that relaxation of the rules does not go far enough. Reynolds officials say that they have spent about $31 million at their Troutdale plant for state-of-the-art pollution control equipment, and if they are required to make the pollution reductions called for in the 1986 rules, Reynolds would be forced to close the 40-year-old plant.

Jan 1, 1982

By Ned H. Snyder

In recent years the Government and other large consumers of coal have appreciated more and more the desirability of definitely determining by chemical analysis and test the character and quality of the coal they purchase. Higher prices for coal point forcibly to the need of giving more study to engine room and boiler room efficiencies and economies; this implies an intimate knowledge of the character and quality of the fuel used. Analyses and tests of delivered coal furnish data whereby power plant results can be comprehensively studied and a continuous check maintained on the coal and on the conditions of plant operation. Under authority of acts of Congress making appropriations for technologic investigation of fuels and the analyzing and testing of fuels belonging to or for the use of the United States Government, a laboratory is maintained at the Pittsburgh station of the Bureau of Mines, where samples representing deliveries of coal purchased for Government use are analyzed and tested. The Bureau of Mines has been active in promoting the purchase of coal by the Government under specifications/ that is, by contracts that make definite requirements regarding the heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analysis. Under many of these specification contracts the bidders guarantee the quality of the coal offered, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled and analyzed to determine whether the coal is of the quality guaranteed by the contractor, and if it is not, the price to be paid is decreased in proportion; but if the coal is of higher quality, the price is proportionately increased. The known analyses of coals or the guaranteed analyses offered by the bidders may sometimes be used for determining the award of a contract, but if the coals offered differ widely in characteristics, it may be difficult to determine which would prove the cheapest fuel without data on their relative evaporative efficiencies. Hence, the making of evaporative tests under service conditions may be necessary in order to determine which coal is particularly adapted for successful and economical use in a certain plant. Once a particular coal is selected, however, regardless of the procedure of determining the award of a contract, then the greatest advantage of the specification method is realized, for it guarantees the purchaser receiving coal of uniform character and quality, thereby insuring the best results in the plant. The success of the specification method for the purchase of coal and the reliability of analysis now rests largely on sampling.3 Improper sampling leads to controversies, with resulting condemnation of the specification method in general and of the value of laboratory analyses and tests in particular.

Jan 1, 1922

By Kenneth J. Miller

To determine the effectiveness of the many new flocculants available to the coal industry 20 of these reagents were evaluated treating slurry feeds to four refuse thickeners. Settling rates and supernatant liquid clarities were determined for each of the flocculants on the four slurries, and zeta potential measurements of the slurry solids were made. The test results showed that the flocculants provided comparable results when judged categorically as anionic, nonionic, or cattonic. It was also apparent that control of zeta potential insures maximum benefit from a flocculant.

Jan 1, 1968

By L. A. Morley

Volume III of the final report examines the indication versus interruption procedures used on motion-drive power equipment, with emphasis on surface excavators. The report begins with a review of the electromechanical acid conversion used with the Ward-Leonard control system. Protection criteria for the drive-system components are then discussed. Fault sources and fault calculations for both the ac supply source and dc power loop are introduced to assist in discussing indication and interruption procedures. The subject is then expanded to examine the dynamic process of the machine and determine the effects of fault current and position of the machine to allow for an orderly shutdown. With this analysis, possible indication an interruption procedures are given for the four-quadrant duty cycle of excavators. The report concludes by introducing other mining operations that utilize similar motion-drive systems and also static (solid-state) drives and recommends further research in these areas, as well as a more detailed examination of the dynamic fault analysis for excavators.

Jan 1, 1982