Search Documents

By R. H. Jefferson

This Bureau of Mines report describes a series of rapid wet chemical methods for the analysis of blast furnace slags. A "complete" analysis for total iron, manganese, silica, lime (calcium oxide), magnesia (magnesium oxide), sulfur, and mixed oxides (R203) can be routinely performed in less than 3 hours. These methods were employed as the analytical control procedures for the Bureau's experimental blast furnace operations and have been satisfactorily applied to the analysis of other slags and calcareous materials.

Jan 1, 1974

By D. S. Kimmel

The Bureau of Mines sponsored development of a system to remotely energize and de-energize the trolley wire in a section in response to demands from vehicles as they enter and leave the controlled section. The system developed utilizes a detector/actuator that controls a dc contactor at the outby end, and a 3 kHz oscillator at the inby end. A prototype system has been built and installed at the Bureau's trolley test site at Bruceton, Pennsylvania which has demonstrated the ability to also provide load discrimination for faults of 300 amperes or more. The system could readily be modified by locating the oscillator on the vehicle to provide automatic de-energizing of the trolley wire when the vehicle's pole is removed or the vehicle leaves the section.

Jan 1, 1978

By A. W. Ambrose

"Introduction.Oil-field operations have often been carried on under great stress and haste, in which the prime purpose has been to put the wells down rapidly as possible, without regard to a few of the various factors affecting cost. In such fields as Burkurnett, Texas, where the well locations are town lots and other small tracts, the operator was concerned primarily with in drilling. In such cases a few thousand dollars more or less in the cost of a well not considered. We are reaching a time, however, when our reserves a,more definitely outlined and properties are being along more economic lines. Operators are becoming more concerned with the actual cost of this work, and are gradually learning that fuel consumption can be reduced in drilling and producing without delaying the speed of drilling, and in the case of production, it will greatly reduce the unit cost per barrel of production.Types of Field Boilers.In the oil fields there are in general two types of boilers; those which are used for drilling wells and are of a more or less portable character, and those established later in a more permanent form and serve for the purpose,of generating steam for producing the oil. As a rule, the latter type of boilers are larger than those of the drilling type. Usually, little care is given to the installation of drilling boilers; particularly in attempting to set them up in such a way as to avoid waste in of fuel. Because of the temporary nature of these installations there may be some justification for not giving them more,attention in this resend, but it is believed that a few precautions could be taken that would amply repay the cost and trouble taken. In connection with the boiler plants that are afterwards established, when a few producing wells have been,brought in with a life of two to ten years and probably longer, much care to the boiler-plant construction and to the installation of recording instruments which will assist in operating the plant at minimum cost."

Nov 1, 1920

By L. C. IlsLey

[The last previous Bureau of Mines publication relative to details of permissible methane detectors (Bulletin 331, published in 1930) describes detectors of four different types, namely flame, combustion, catalytic, and a combination Wheatstone-bridge axed catalytic type in which catalytic action at the surface of a platinum filament when in methane causes a change in the temperature and resistance of the filament, thus unbalancing the bridge circuit and giving a reading proportional to the methane concentration. Three detectors of the latter type have been approved since 1933. A brief description of each follows: U. C. C. Detector Approved No. 902, covering the U. C. C. indicating detector, as described in Bulletin 331, was entered January 27, 1330, to cover important chances in design that permit checking; the calibration of the detector at any time, whether in gas or fresh air. Essential features of the detector are shown in figure 1.]

Jan 1, 1937

By Mark S. Sanders

Based on laboratory tests and preliminary field tests of off-the-shelf steel toed rubber boots, a molded sole design was developed to provide increased traction over conventional calendared sole miners' boots. The pattern provided sharp edges perpendicular to both lateral and fore-aft slip vectors. The sole was designed to reduce mud caking. An instep lace-up capability was added to better secure the foot inside the boot. A five month field evaluation compared the prototype boots to the boots the participants usually wear. Although objective slip and fall data showed no significant advantage for the prototype, subjective evaluations made by the participants indicated increased traction for the prototype boots. Approximately 75 percent preferred the prototype to their own boot. Approximately one-third used the lace-up capability. It was concluded that molded soles provide better traction than calendared soles for the underground mining environment.

Jan 1, 1982

By George S. Koch

Several methods of calculating ore grades by diamond-drill sampling in the Homestake mine, Lead, S. Dak., have been evaluated by statistical analyses of assay data. The natural distribution of gold particles, partly masked through sampling and assaying procedures, is probably lognormal. As a consequence of the gold particles being clustered rather than randomly distributed within the ore bodies, (1) more mine samples are needed to obtain a specified precision of mean grade than the number predicted by the standard-error-of-the-mean law; (2) the variance of gold values is not inversely proportional to sample volume, and, therefore, small-diameter drill core yields samples nearly as good as larger diameter core; and (3) sampling at 5-foot intervals provides nearly as good results as sampling at shorter intervals.

Jan 1, 1971

By W. L. Falke

Procedures in which manganese compounds are reduced and the metal is volatilized and selectively condensed, a hitherto neglected area, were investigated. More than 95 percent of the manganese was recovered from high-melting-point ores whether vacuum volatilization or atmospheric pressure volatilization was used, but neither process is economically attractive under present price-cost conditions.

Jan 1, 1966

By R. Carson Dalzell

The use of nuclear fission for chemical process heat offers the special advantage of high temperature, limited only by materials of construction. The process heat may be supplied economically at elevated pressures, since no compression of combustion air is required. For the initial effort in developing a high-temperature reactor, the indirect cycle, using helium as the heat-transfer medium, was chosen. The major problems are the design of high-temperature fuel elements, construction of an exchanger to transfer heat to process streams in the range of 2,500° F., and development of compressors capable of recycling helium at 1,000° F. and above. A conceptual design of a nuclear reactor to furnish process heat for coal gasification has been made. Spherical fuel elements utilizing a graphite structure, impregnated with uranium carbide fuel, were chosen, as spheres offer the possibility of easier loading and unloading of the reactor. Calculations of pressure drop and gas-pumping power for the system are included.

Jan 1, 1959

By L. C. IlsLey

The last previous Bureau of Mines publication relative to details of permissible methane detectors (Bulletin 331, published in 1930) describes detectors of four different types, namely flame, combustion, catalytic, and a combination Weatstone-bridge and catalytic type in which catalytic action at the surface of a platinum filament when in methane causes a change in the temperature and resistance of the filament, thus unbalancing the bridge circuit and giving a reading proportional to the methane concentration. Three detractors of the latter type have been approved since 1930. A brief description of each follows: U. C. C. Detector Approval No. 902, covering the U. C. C. indicating detector, as described in Bulletin 331, was extended. January 27, 1930, to cover important changes in design that permit checking the calibration of the detector at any time whether in gas or fresh air. Essential features of the detector are shown in figure 1.

Jan 1, 1937

By Albert E. Long

To date the commercial diamond bit setters have been principally interested in the speed with which they could produce a sharp, fast-cutting bit. Thus, a premium has been placed on setters who combine a high degree of manual dexterity with the ability quickly to select the Sharp points and edges of the diamonds and set them in the mold without lost motion. The premium on speed does not allow the setters the time, nor are they trained, to consider also the crystallographic structures of the diamonds which are the clues indicating the harder and more suitable working surfaces. Since early fall of 1949, the Bureau of Mines has been conducting a long-range series of experiments in which drill bort have been oriented in diamond bits in an effort to determine the effects and economic practicability of utilizing the hardest surfaces of the diamond crystal structure. The preliminary experiments completed to date indicate that a substantial saving in diamonds may be affected by using the harder areas of the diamonds as working surfaces in the crown of diamond bits. The experimental work is being conducted by the Bureau of Mines in the laboratories and full-scale mine of the Mining Research Branch, Minerals Technology Division, Region VIII, of the U. S. Bureau of Mines at the Mount Weather Station, Bluemont, Va.

Jan 1, 1951

By Bowles Oliver

"Modification of Quarry Process.Limestone beds are formed by processes of nature, processes that have been in operation for thousands and perhaps millions of years. Therefore, their com- position and physical properties are long-established and unalterable features over which man has no control. He must take them as he fields them.It is undoubtedly true that the character of lime depends largely on the nature of the parent limestone. A high-calcium lime cannot be manufactured from a dolomite, nor can a pure lime result from the calcination of an impure raw material. However, in the process of turning limestone into lime man is not entirely helpless in his control of quality. Even though a deposit is variable in character a single lime product of uniform quality may be produced by judicious quarrying. A single grade of product may not always be desired, the producer may wish to supply the needs of a variety of users each demanding U different grade or quality of lime such a series of graded products may be produced in part at least by modifying the quarry method. Thus, by changes in quarry practice a single product or a variety of products may be made. The latter problem will be considered at a later time, and the present paper devoted to the first named question' that of producing a single grade of lime from a deposit of variable rock,It is realized of course that uniformity in the product is influenced greatly by manufacturing processes such as calcining' hydrating' grinding or storage, but the present discussion is confined to the influence of raw materials only. In considering the various devices that may be employed it is realized that much remains to be learned, and it is hoped that many operators will contribute to the discussion as they have already done in connection with previous papers of this series."

May 1, 1923

By Jonnie M. Estes

A two-constant equation is presented for helium from 30° = T = 1,473° K. This equation is developed by modifying a generalized equation of state originally presented by Redlich and Kwong (20).3 The modification consists of setting B = 0.06372 Tc/PeT. This modified equation represents the compressibility factors of each of 80 isotherms tested in this temperature range to less than 1 percent average deviation.

Jan 1, 1967

By R. R. Sayers

Carbon monoxide poisoning, as usually encountered, is an acute condition resulting from breathing atmospheres containing that gas. It is characterized clinically by headache, dizziness, weakness in the legs, increased respiration at first which later becomes irregular and depressed, collapse, unconciousness, and death; anatomically it is characterized by temporary changes in the red blood cells due to the combination of carbon monoxide with hemoglobin, and, in prolonged severe exposures, degenerative changes in various tissues of the body, especially those of the central nervous system. No race or nationality is immune or has a, special tolerance for carbon monoxide. From data at hand, it is known that both sexes are about equally susceptible. All ages are affected, but small percentages seem to have a more deleterious effect upon young animals and this is possibly true of children. Exercise, high temperature and humidity, and low oxygen content of en atmosphere increase the degree of poisoning for a certain concentration of carbon monoxide. Anything that lowers the physical fitness of a man, such as illness, overwork, or excesses of any kind, exaggerates the effects. More cases of poisoning from carbon monoxide occur in coal mines in the cold months of the year, because explosions take place more frequently during that period, also in homes where gas is used for beating purposes, and in garages from accumulation of automobile exhaust gases due to poor ventilation.

Jan 1, 1923

By T. L. Hebble

The Bureau of Mines investigated a hydrometallurgical procedure to recover Co, Ni, and Cu from an electrolytic zinc industrial copper filter cake. The copper filter cake is presently unmarketable or of low value because economic and environmentally acceptable processing technology is lacking. Research by the Bureau of Mines has developed a multistage process for recovering or recycling over 93 pct of the Zn, Cd, Cu, Co, and Ni from this material. The stages involved are (1) wet sizing, (2) H2S04 leaching of undersized material, (3) H2S04-Mn02 leaching of H2S04 leach residue, (4) selective precipitation of As, Cu, and Co-Ni products, and (5) precipitation of manganese for recycling to the leach circuit. The final process residue is only 1.6 wt-pct of the initial cake and consists of lead sulfate.

Jan 1, 1981

By H. R. Beard

The citrate process for sulfur dioxide emission control was developed in pursuit of the Bureau of Mines goal of minimizing the adverse environmental impact of mineral-processing operations. This publication describes the gas analysis procedures used during development of the process. The research required the capability to analyze SO2, H2S, CO, CO2, COS, volatile hydrocarbons, NO, NO2, O2, N2, and H2. The methods described include gas chromatography, electrochemical detection, infrared spectroscopy, and the use of a computer program to predict the product composition in complex reactions. Laboratory and pilot plant applications are discussed.

Jan 1, 1979

By V. Vallyathan, Xianglin Shi, N. S. Dalai

While Cr(VI) is a known carcinogen, the underlying biochemical mechanism is still not fully understood (1). In a pioneering study Jennette (2) utilized electron spin resonance (ESR) spectroscopy to demonstrate that a long-lived Cr(V) species is generated during the reduction of Cr(VI) by microsomes in the presence of NADPH. Later Wetterhahn and co-workers (3, 4) showed that incubation of chromate with isolated rat liver mitochondria causes the reduction of Cr(VI), as well as the formation of a Cr(V) species. Analogous Cr(V) species have also been detected in the reduction of Cr(VI) by other cellular systems such as Hanserulla polymorphared (5) and blood cells (6, 7). All these as well as other studies (8-12) have suggested that this Cr(V) species plays a significant role in the mechanism of Cr(VI) toxicity. Thus far, however, the chemical structure of this dominant Cr(V) species formed in cellular systems has not been identified, and this observation provided an impetus for the present investigation. Another reason for undertaking this study was that some recent reports (10-16) suggest that hydroxyl ('OH) radicals may also play an important role in the mechanism of Cr(VI) toxicity. In particular, it has been shown that OH radicals are formed in reactions between Cr(V) species and H2O2 (13-16), and that the radical yield depends on the chemical structure of the Cr(V) species (15). For example, while Cr(V)-diol complexes efficiently generate OH radicals, another Cr(V) species, the tetraperoxochromate (CrO3/8) ion, does not (15). Thus in the present study, we focused our attention on the following: (a) structural identification of the Cr(V) species generated in the reduction of Cr(VI) by subcellular as well as cellular systems, using microsomes, mitochondria, and Escherichia coli; (b) possible detection of OH radical in the same systems since there is no earlier report of chromium-mediated generation of 'OH radicals in a cellular system; (c) possible involvement of molecular oxygen in chromium-related OH radical generation since a recent report (17) indicated that Cr(VI) mutagenesis is strongly oxygen dependent; and (d) elucidation of the mechanism of OH radical formation in these systems.

Mar 1, 1992

By James C. Barker

Yttrium and rare-earth element. pegmatite dikes are associated with a peralkaline granitic and nephelene syenite complex near Dora Bay on southern Prince of Wales Island. Mineralized dikes were mapped and sampled during USBM investigations in 1987 and 1988. Coarse-grained pegmatite dikes, which emanated as late-stage magmatic fluids from the intrusion, further evolved into vein-dikes and ultimately silica-rich veins. The dikes can be traced up to two miles along a north-south zone. Lithophile elements exhibit a pronounced zonation in vein-dikes and veins that are distal to the Dora Bay complex with increasing values correlating with increasing distance from the complex. The pattern of mineralization suggests very late stage magmatic fluids containing the incompatable lithophile elements were injected into a preexisting north-south fracture zone. REE mineralogy exhibit fine-grained intergrowths of principally thalenite and bastnaesite with lessor monazite and eudialyte. Euxenite contains most of the columbium values and zircon is commonly associated with the dikes. Estimates of inferred and hypothetical resource tonnage range from 1.7 X 1C6 to 8.5 X 106 st for two deposits. Contained RED (including yttrium) averages 0.5 pct and ranges up to 2.0 pct. Deposits are of polymineralic composition and about half of this resource comprises the heavy yttrium subgroup.

Jan 1, 2011

By K. K. Kelley, W. W. Weller

This report contains experimentally determined heat capacity data for four crystalline sulfides -- AsS , GeS , NiS , and Ni3 S₂ -- over the temperature range from 50 ° to 298.15 ° K. The heat capacity data were used to evaluate the entropies of the sulfides at 298.15 ° K. Entropies of formation from the metals and rhombic sulfur and from the metals and diatomic sulfur gas are also included .

Jan 1, 1964

By E. J. Murphy

"INTRODUCTION This investigation is a continuation of previous work 3/4/5/ on the gaseous products of permissible explosives with and without sheaths. The range of oxygen balance of the explosives has been considerably increased. As has been shown previously, certain approximate relations exist between the volumes of gaseous products and the oxygen balance. Further systematization of the data is not feasible, since the method of theoretioal calculatln of the gaseous product is not yet satisfactorily developed. In a previously described method, 6/ it has been assumed that the explosion occurs at constant volume and that thermodynamic equilibrium is established. Apart from the presumably less important uncertainty of some of the thermodynamic data, it is not known how the confinement of the shots in the Bichel gage or the Crawshaw-Jones gage should be treated, or whether thermodynamic equilibrium is fully attained; nor can the extent to which the equilibrium composition changes during the subsequent period of expansion and cooling be judged with any reliability. Therefore, no calculations have been attempted. However, in anticipation of possible future theoretical interest and as an aid in answering practical problems, the new data are presented in the same minute detail as was done previously."

Mar 1, 1948

By Franklin B. W. Woodbury

The Bureau of Mines undertook the development and evaluation of a system to provide a simultaneous, on-line determination of both iron and silica in iron ore beneficiation streams as part of a program to improve the efficiency to mineral separation processes, Californium-252 (252-Cf) was the neutron source used in the system for measuring the amounts of silica and iron in bulk slurries by thermal neutron capture-gamma ray spectra analysis. The theory of thermal neutron capture-gamma ray reactions and their potential application to mineral processing stream analysis is discussed. The prototype system and supporting software developed by the Bureau is described. During the initial phase of the work, both simulated and actual pilot plant slurries were investigated using a 60-to 32-µg 252-Cf neutron source. The percent solids of the slurries was ranged from 2 to 40 percent and the silica and iron content ranged from 1.5 to 83 percent and from 10 to 65 percent, respectively. Accuracy of the determination of the components in the solids was dependent upon the percent solids in the slurry.

Jan 1, 1980