Search Documents

By Michael E. Henderson

Presented in this report are the experimental results of coarse coal slurry degradation data obtained from the Hydraulic Transport Research Facility (HTRF) at the Pittsburgh Research Center (PRC), Bruceton, PA. The facility is operated by Boeing Services International, under Bureau of Mines Contract No. J0333956. Presented in this report are the experimental results of coarse coal slurry degradation data obtained from the Hydraulic Transport Research Facility (HTRF) at the Pittsburgh Research Center (PRC), Bruceton, PA. The facility is operated by Boeing Services International, under Bureau of Mines Contract No. J0333956. This particle degradation report is a summary of the particle distribution data obtained at the HTRF for the period 26 November 1982 to 1 October 1983. The testing covered herein is for coarse Pittsburgh Seam coal in the 6-in (150 mm) and 12-in (300 mm) pipelines, at velocities ranging from 5 to 18 ft/s (1.5 to 5.5 m/s), and at concentrations by weight ranging from 15 to 55 pet. Particle size distribution samples were taken systematically throughout the testing.

Jan 1, 1985

By Paul W. McGann

THE MINERAL INDUSTRIES had a near-record year in 1950, as rising industrial activity in general, greatly accentuated by the outbreak of hostilities in Korea in midyear, called forth increasing supplies of mineral fuels and raw materials. The aggregate value of mineral production was second only to that in 1948, and the aggregate physical volume was exceeded only in 1948 and 1947. Lower coal production accounted for the failure to surpass these earlier years. Growth of production was fairly constant throughout the year, especially for crude petroleum; its physical output for the year as a whole exceeded that of 1949 by 7 percent. According to Federal Reserve Board indexes, other relative gains were 16 percent for coal, 9 percent for fuels in general, and 17 percent for metals. The increase for mining in general was of the order of 10 percent. This was not quite as large as the general increase in industrial production but clearly reflected the total-industrial trend (see fig. 1).

Jan 1, 1953

By C. P. Mabie

This report summarizes studies by the Bureau of Mines in developing a simple method for estimating the phosphorus pentoxide (P205) content of finely ground sedimentary phosphate ores and beneficiated products. The method used involved leaching, filtration, and precipitation. The Bureau found that measurement of the volume of ammonium phosphomolybdate precipitate obtained from samples containing 16.8 to 37.7 percent P205 and the use of an appropriate calibration curve permitted estimates of percentage of P205 content accurate within ± 1.1 to ± 2.6 percent, respectively, at the 95-percent confidence limits. Incidental to mineral dressing and petrographic investigations of western phosphate ores in 1959, the Bureau of Mines undertook development of a simple process-control method for rapid on-the-spot evaluation of phosphate-mineral recovery. Because of the fine-grained and obscure character of western phosphate ores, chemical, rather than microscopic or petrographic, techniques were investigated. The described method involves acid decomposition of the ore or product, filtration, addition of ammonium molybdate reagent to the filtrate, and centrifuging and measuring the volume of yellow ammonium phosphomolybdate precipitate produced.

Jan 1, 1961

By Wing G. Agnew

It is thought that a brief description of the unique mining and milling procedure at the Doyle nine may be interesting to those engaged in small-scale operations at old mines or in working new ore body adjacent to old workings. It also shows what can be done with r. small capital outlay in working a zinc-lead mine on a small scale; as the operation herein described was begun 3 years ago with four men and it now employs 17 men. The original idea was to mine out any ore left around the edges of some old stones above the water level and to rob pillars after an old stope became filled with waste and tailings. This has been done, and the procedure is still being followed; at the same time a paying lead is being mined toward an area in which churn-drill holes have shown ore. Also, preparations are now being made to do some pumping.

Jan 1, 1936

By Alan G. Mayton

The Bureau of Mines conducted one of the most extensive studies on surface mine illumination to date, to assess the illumination needs of mobile surface mining machinery with respect to the visual tasks required of machinery operators. Field Investigations were performed at 22 surface mining operations, coal and metal-nonmetal, within several mining regions of the United States. Visibility and illumination were measured for 159 visual tasks performed by equipment operators on or near 57 surface mining machines, including draglines, shovels, blasthole drills, bulldozers, loaders, haul trucks, graders, scrapers, and several service-type vehicles.

Jan 1, 1987

By Barry Beith

This report details a study which was designed to assess the effect of retroreflective material on detection and form recognition of workers in the mining environment. Further, the study attempted to determine an optimal configuration of retroreflective material with respect to amount and placement on the body to facilitate detection and form recognition. The study involved a one-fifth scale simulation of the perceptual task found in the underground low seam coal mine. Four different configurations of reflective material were presented in various body positions, common to low coal miners, at three different locations in the visual field, i.e., 10, 25, and 45 degrees from focal line-of-sight. All reflective configurations significantly improve detection and form recognition over configuration (cap only) worn by miners. As the amount of reflective material increased, accuracy also tended to increase. Based on the configurations investigated by this study, the Armband configuration (i.e., refectorized armbands, belt, self-rescuer and battery pack) was determined to be optimum. It is recommended that an actual field evaluation be made using the Armband configuration to establish if simulator results are generalizable to the underground mining environment.

Jan 1, 1980

Tax for Toxic Waste Cleanup. - The Superfund Act of 1980 became effective April 1, and provides that producers of certain metals and chemical substances are to be taxed in order to fund toxic waste cleanup. Industry will provide 88% of the 5-year, $1.6 billion fund. The Environmental Protection Agency will administer the Act, but the Internal Revenue Service will be responsible for collection of the industry tax. Under the Act, nickel companies, for example, will be required to pay a tax of 0.225 cents per pound on pure nickel products produced or imported into the United States. Standard for Exposure to Lead. - The Occupational Safety and Health Administration (OSPA) has announced a stricter standard on the test of a worker's exposure to lead. Effective May 15, in all lead intensive occupations with the exception of those at primary and secondary lead smelters, a worker would have to be removed from his work station if the level of lead in his blood tests out at 60 micrograms of lead per 100 grams of blood, instead of the previous standard of 70 micrograms. In the case of primary and secondary lead smelters, the ruling has been stayed until June 1, 1981, to allow time for further study.

Jan 1, 1981

By Albert S. Konselman

This paper describes the mining methods and operating costs for 1938 at the South Burns shaft, situated in the Cripple Creek district, Colorado. The shaft is operated by Golden Conqueror Mines, Inc., through which portions of the properties of the Acacia Cold Mining Co., The Free Coinage Gold Mining Co., and The United Gold Mines Co. are worked under lease. During 1938, 30,773.61 dry tons of ore averaging $9.59 in gold per ton was mined. Of this, 10,138.439 tons averaging $10.65 per ton was produced on company account, and 20,635.171 tons averaging $9.05 per ton was produced by "split-check" lessees.

Jan 1, 1940

By J. S. Dunning

A primary goal of the Federal Bureau of Mines is to minimize the requirements for scarce mineral commodities through conservation and substitution of more abundant elements, such as iron and molybdenum. One example of this is the research effort to devise substitute materials for specialty alloys, thereby conserving nickel and chromium in high-volume stainless steels. As a possible substitute for the solid solution strengthening of chromium and nickel, the precipitation hardening characteristics of a number of binary iron-based systems in which Laves phase precipitates, such as Fe2Mo, are formed were investigated. Several hardening responses were observed, but none were ideal. The Fe-Ta binary system had the highest magnitude of hardening, even with low alloy additions, and the Fe-Mo system had unique stability at temperature. Accordingly, the Fe-Mo-Ta system was selected for study to determine if a ternary Laves phase could combine high hardening with long-term stability at elevated temperature. Hardening and stability were reflected in excellent elevated temperature, tensile, and stress rupture strengths. Future research will study ternary systems based on more abundant resource materials, such as the Fe-Mo-Ti system, together with additions, such as aluminum and minimal chromium, to provide oxidation resistance.

Jan 1, 1979

By E. P. Youngman

The law of June 5, 1911, suplements and amends the Laws of April 21, 1810 (the basic law) and May 2, 1837. The Royal Decree of September 15, 1919, coordinates the provisions of the Law of June 5, 1911, with those of the Laws of April 21, 1810, of May 2, 1837, and of July 8, 1865, that have remained in force, as well as with certain articles of the Law of September 1, 1913, which revisad the system of taxation. The revised code has been brought together in one volume.3 All citations in this abstract refer to the coordinating Royal Decree of September 15, 1919, unless it is otherwise specifically indicated.

May 1, 1930

By J. W. Adams

Measurements of surface magnetic field noise were made at various locations over the Geneva Coal Mine near Price, Utah, on June 12, 1973. The locations selected were on the surface over emergency locator beacons underground at depths between 3S0 meters (1150 ft.) and 488 meters (1600 ft.). The surface terrain where these measurements were made was mountainous, and access was difficult. There were no power lines within several miles, and the weather was clear; therefore, the magnetic noise levels were about as low as will normally occur. Results of measurements of distant sferics indicate rather sharp cutoff frequencies below which broadband, impulsive noise is attenuated. The mechanism of propagation for this noise above the daytime cutoff frequency of 3500 Hz and the nighttime cutoff frequency of 1700 Hz is deduced to be a waveguide formed by the D or F layers of ionosphere as an upper plane and the earth as a lower plane.

Jan 1, 1974

By Victor E. Kral

"SUMMARYA preliminary examination of the Buena Vista iron deposit was made in June 1942 by Paul E. Pesonen, mining engineer of the Bureau of Mines. Subsequent examinations were made by D. W. Butner, of the Bureau, in March 1943, and by the author in July 1944, who recommended exploration by diamond drilling, trenching, and sampling. Work on the project was done during the period March 28 to May 26, 1945.Property holdings, comprising 16 claims known as the Buena Vista group, are situated in sec. 4, T. 24 N., R. 34 E., Mount Diablo base and meridian, north Churchill County, about 37 miles east of Lovelock, Nev.Three diamond-drill holes totaling 575 feet were drilled; 45 small pits and ten trenches, totaling 435 linear feet, were excavated, and 84 channel samples totaling 862 feet were obtained under supervision of the Bureau.Purpose of the project was to determine the possible downward extension of the mineralized sections exposed in the outcrops and to determine grade of the ore.Bureau work was confined to one claim only - the Iron Mountain."

Jun 1, 1947

By John E. Pahlman

The Bureau of Mines investigated the feasibility of removing heavy metals from mineral-process waste streams by precipitation with lignochemicals and humic acids. Lignochemicals are by products from the paper industry, while humic acids are obtained by caustic treatment of peat, subbituminous coal, and lignite. These high-molecular-weight organic materials have many functional groups, which can coordinate and form innercomplex salts with heavy metals that are crystalline precipitates. Filtering of a humic-acid-or lignochemical-treated solution or waste stream containing these precipitates removes the heavy metal sequstrates. Tests were conducted with two lignochemical samples, three humic acid samples, lime (CaO), and sodium hydroxide (NaOH) in which increasing amounts of these additives were reacted with 50 mL of solution containing Fe3+ , Al3+, Cr3+, Pb2+, Cu2+, Cd2+, Zn2+, Co2+, Ni2+, Mn2+, and Hg1+. At the appropriate pH, greater than 90-and 99-pct removal was achieved for these 11 heavy metal ions from the 10-and lOO-ppm solutions, respectively, using lignochemicals and humic acids. Removal efficienC)' with these organic materials is better than that with CaO, especially for the more toxic ions, Hg1+, Cd2+, and Pb2+. Unlike the precipitates formed with NaOH or CaO, those with lignochemicals and humic acids are compact and noncolloidal. The volume of their sludge is sharply lower than that of the finely dispersed lime or soda precipitates; thus, their removal in settling tanks or by simple filtration is enhanced.

Jan 1, 1988

By N. A. Gokcen

Equilibrium partial pressures of gaseous HCl and H2O over aqueous binary and ternary solutions of HCl and AICls were calculated or estimated in the range of 20° to 110° C, and up to saturation with AlC13?6H2O. The results were extended to solutions containing less than 10 wt-pct FeCl3 by assuming that FeCl3 and AIC13 are equivalent on the molar basis, since both salts have trivalent cations with a cammon anion. The ionic activity coefficient of HCl and the equilibrium constant for dissolution of gaseous HCl were also computed. This research is part of the effort by the Bureau of Mines, U.S. Department of the Interior, to provide thermodynamic data to expand the technology base relevant to the extraction of alumina from nonbauxitic domestic raw materials.

Jan 1, 1980

By W. H. Eddy

The Bureau of Mines conducted laboratory batch and continuous flotation processing tests on waste granite fines from South Carolina to determine the possibility of recovering high-quality feldspar and glass sand. Three flotation systems were used for removal of the iron-bearing biotite: Two employed an alkaline anionic-cationic circuit and the third employed an acid cationic circuit. Commercial-grade products were obtained when the remaining biotite was magnetically removed from the feldspar and quartz concentrates. Continuous flotation processing yielded a feldspar concentrate containing, in percent, 3.60 Na20, 5.60 K20, and 2.25 Ca0, with recoveries of 75.3, 66.6, and 72.6 percent, respectively. The feldspar tailing was high quality glass sand containing 98.0 percent Si02 and 0.025 percent Fe203; about 60 percent of the quartz was recovered.

Jan 1, 1972

By John C. Edwards

Chapman-Jouguet detonation calculations were carried out for pentaerythri-tol tetranitrate (PETN), TNT, and ammonium nitrate-fuel oil (AN-FO) explosives using the compressibility form of an equation of state of hard spheres based upon Percus-Yevick (PY) theory, and a chemical equilibrium detonation code called TIGER. Similar calculations were also carried out with the Becker-Kistiakowsky-Wilson (BKW) equation of state. For PETN, the BKW equation gives somewhat better agreement with experimental values of detonation velocity and pressure. However, in terms of experimental temperatures and concentrations of the minor product species (NO), the predictions of the PY equation are shown to be more satisfactory. Similar comparisons of experimental and theoretical results for TNT and AN-FO indicate that the PY equation has general utility in predicting the detonation properties of condensed explosives at moderate loading densities (Po < 1.3 g/cm3).

Jan 1, 1974

The Bureau of Mines has conducted considerable research to improve life support technology for underground mining applications. This proceedings volume presents several new developments that may help increase the chances of mine workers in surviving underground disasters. Several papers address the performance of present self-contained self-rescuers (SCSR&apos;s) and provide proposed guidelines for the design and testing of a second-generation SCSR. Improvements In the safety and effectiveness of mine rescue and recovery operations are described, including the design of a low-profile rescue breathing apparatus and a rescue team helmet.

Jan 1, 1987

By H. F. Weaver

The 18th National First-Aid and Mine Rescue Contest was held in the Memorial Auditorium, Buffalo, New Vork, October 5, 6, and 7, 1959. The meet was sponsored by the Federal Bureau of Mines and the Joseph A. Holmes Safety Association, in cooperation with State mine inspection agencies, management and labor of the mineral extractive industries, and other safety minded groups. The Arrangements Committee, as authorized by the General Committee, made a11 the necessary arrangements for conducting the 1959 contest. Members of the Arrangements Committee were: Harry Gandy, Jr. (chairman), National Coal Association; James B. Benson, Southern Coal Producers&apos; Association; Charles Ferguson, United Mine Workers of America; George C. Trevorrow, Bituminous Coal Operators&apos; Association; and James Westfield, Federal Bureau of Mines.

Jan 1, 1960

By C. P. Fang

"For lower stages of multinozzle micro-orifice impactors, as many as two thousand nozzles are uniformly arranged within a cluster diameter of 1.06 inches. In the impaction region the mass flowrate of the spent air increases along the radius and reaches a maximum at the periphery. This crossflow can significantly deflect the air jets of the outer nozzles, hence the characteristics of impaction changes.Investigators in heat transfer and fluid mechanics have studied the influence of crossflow on jet deflection and found the dimensionless deflection of the jet centerline X/Dn is a function of (S/Dn)(l/m) . only, here X is downstream coordinate measured from the center of the jet orifice, Sis the jet-to-plate distance, Dn is the orifice diameter and m is the jet/crossflow mass flux ratio defined as:"

Jan 1, 1989

By Arthur M. Hartstein

The Bureau of Mines, through contract with Ultrasystems, Inc., obtained data on the oxidative degradative behavior of a number of materials used in coal mines. Tests were performed using a stagnation burner arrangement. Materials examined included those used in typical coal mining operations such as (1) polyvinyl chloride-containing materials. (2) neoprene compositions, (3) rigid foams (urethanes/isocyanates), (4) miscellaneous materials (including jute, fiber glass, and polyethylene), (5) coal, (6) fluids (phosphate esters, organic esters, oil-water emulsions), and (7) composites. The composite comprised a mixture of a phosphate ester fluid with (1) coal, (2) a representative polyvinyl chloride sample, or (3) a neoprene-type composition. A number of decomposition products are identified that could represent a potential health hazard to miners including HC1, CO, SO2 and H2S, if they were generated to exceed toxic levels.

Jan 1, 1974