Search Documents

By Joseph Cervik, Gerald L. Finfinger

The Bureau of Mines conducted an experimental degasification project in Island Creek Coal Co.'s Virginia Pocahontas No. 5 mine. Methane from the over- lying Pocahontas No. 4 coalbed was entering mine workings in the Pocahontas No. 3 coalbed through fractures in the roof rock. Small-diameter (1-5/8-inch) holes were drilled into the overlying coalbed to reduce the gas pressure and intercept methane flows, which were piped to the surface through an under- ground 6-inch-diam steel pipeline. The total methane flow rate from the vertical holes averaged 150,000 ft3/day for the first month. Methane flows into the mine were reduced by 47 pct, thereby demonstrating the effectiveness of this form of degasification in reducing ventilation requirements and providing a safer working environment.

Jan 1, 1979

By W. I. Nelson

This paper describing the mining practices at the Engels mine is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The Engels Copper Mining Co. operates two mines about 3 miles apart in Plumas County. Calif. Both mines send ore to the same mill, and the methods of the larger, or Engels mine, are described in this paper. Between 800 and 1,000 tons of 1-3/4 to 2-1/2 per cent copper ore are mined daily from this mine by a shrinkage method. Connection is made with the Western Pacific Railroad at Paxton by the Indian Valley Railroad, which is 22 miles long and operates a daily mixed train to the mine.

Jan 1, 1930

By W. P. Diamond

It is estimated that more than 1 trillion cubic feet of methane is contained within the coals of the Mary Lee group in Jefferson, eastern Tuscaloosa, and southern Walker Counties, Ala. Most of this methane will be encountered by mining. Coals of the Mary Lee group are presently being mined at depths exceeding 1,000 feet and will in the near future be mined at even greater depths, where the problem of methane gas affecting the mining operations will be acute. It is calculated that approximately 90 pct of the methane is at depths greater than 1,000 feet, and over half of the gas is contained within only 12 pct of the study area which is under more than 1,500 feet of over-burden. Degasification in advance of mining will increase mine safety, reduce ventilation expenditures, increase productivity, provide an additional energy source, and make it possible to mine parts of deep coalbeds that probably could not otherwise be mined.

Jan 1, 1976

By John W. Finch

The Secretary of the Interior acting through the Bureau of Mines and the Geological Survey is authorized by the Strategic Materials (Public No. 117 - 76th Cong., Chapter 190 1st Sess.) to make investigation concerning essential minerals of which the quantities or grades obtainable from known domestic sources are inadequate. The Bureau of Mines, in carrying out its part of this program, may investigate deposits of such minerals in whatever manner may be necessary, in order to determine (1) the extent and quality of the are, (2) the most suitable method of mining and beneficiating it, and (3) the cost at which it may be produced. The essential objective in doing these things is to determine where and how supplies of minerals and metals of which domestic production is usually inadequate might be obtained in a national emergency, even though at higher cost than usual.

Jan 1, 1939

By R. E. Thill

The ultrasonic pulse measurement system described measures velocities of longitudinal (compressional) and shear waves in rock to give values that can be used with density values to determine the dynamic elastic constants of rock. A special feature of this pulse measurement system is its unique acoustical bench that minimizes errors in pulse transit times that are commonly associated with coupling, sample alinement, and sample orientation. Some special features of the acoustical bench are its highly versatile transducer cartridges, a pneumatic ram coupling device, an orientation mechanism, and a vacuum chuck sample holder. The lathe-bed-like construction of the acoustical bench assures automatic alinement of samples and versatility in accommodating samples of various shapes and sizes.

Jan 1, 1968

By Noel N. Moebs

This report summarizes 10 selected Bureau of Mines research contract reports produced from 1970 to 1980 which consist largely of geologic studies of coal mine roof support problems. Significant highlights from the contract final reports are discussed and presented in practical terms. The selected reports focus on the Appalachian and Illinois coal mining regions. In the Appalachian coal region, two geologic structures, roof rolls and slickensides, predominate over all structures as features that directly contribute to roof falls. Studies of these and other structures are reviewed, and improved methods of utilizing drill core and core logs to prepare hazard maps are presented. Among the reports described are several on the weakening effects of moisture on shale roof, as determined from both laboratory and underground measurements, and an assessment of air tempering as a humidity-control method. Also summarized are findings concerning the time lapse between roof exposure and permanent support installation as a factor in the effectiveness of roof bolting.

Jan 1, 1984

By H. G. Iverson

An investigation was conducted on the conditions affecting the precipitation of aluminum by autoclaving synthetic solutions containing Na2SO4, Al2(SO4)3, H2SO4, and H2O. Virtually all of the alumina could be precipitated as natroalunite (NaAl3(SO4)2 (OH)6). This product could be readily filtered and dried. Results are reported in terms of alumina precipitated in this compound and not in terms of alumina itself. Solutions of ~ 0.30, ~ 0.60, and ~ 0.80 mole/liter A1203 and various concentrations of H2SO4 and Na2S04 were investigated. The optimum time and temperature for autoclaving were 20 to 30 minutes at 200° C. The highest yields of natroalunite were obtained from solutions containing little H2SO4 and ~ 2 moles Na2SO4 per mole A1202. Acid in quantities of 0.3 to 0.5 mole/mole of alumina in solution depressed the yield to 90 percent or less. In differential thermal analysis, at 1,000° C the natroalunite precipitate decomposed without melting to yield SO, and SO2 gases, a solid composed of Na2SO4, and gamma and alpha Al203. Continued heating to 1,200° C produced No SO, and alpha A1303. Water-leaching of this product removed the Na2S04 and left a final residue of alpha A1203.

Jan 1, 1968

By Michael D. Fenton

Detailed comprehensive assessment of the performance of Afghanistan's mineral industry during 1987 is virtually impossible, owing to the paucity of reliable published information. It was evident, however, that the level of civil disorder, now in its eighth year since the arrival of significant numbers of Soviet troops, was in actuality little removed from open civil war. Insurgents controlled substantial areas of the country and imperiled any industrial activity in many places. Assistance programs by the U.S.S.R. and other Eastern European nations were directed at developing the country's meager mineral industry, but the economy was generally viewed as chaotic. The inflation rate was somewhere between 20% and 30%; major food shortages contributed to the discontent of the population, and numerous villages were devastated by Soviet and Afghan Government campaigns to destroy the insurgents and cut their supply routes. Moreover, proposals by the Soviets and the Kabul Government aimed at reducing tensions with the rebels and scaling down the warfare seemingly were taken by the opposition as signs of weakening by the Soviet-backed Government, and rather than reducing aggressions, seemed to heighten insurrectionist activities. Efforts to entice the substantial number of Afghans who have fled to nearby areas of Pakistan and Iran to return to their country seemingly were failures, and indications near yearend that the Soviet Union might soon begin withdrawal of its occupation force of nearly 120,000 did little if any to reduce disorder.

Jan 1, 1989

By Charles L. Kimbell

For a study such as this, which summarizes and amalgamates much information collected, compiled, and utilized by the numerous U.S. Bureau of Mines country specialists and branch chiefs for inclusion in the country and regional reports that comprise the five other sections of 1991 Minerals Yearbook-International Review, it is clearly impossible to cite all sources of information used in its presentation, but some recognition is due. Generally speaking, this study and its related detailed studies on countries and areas would be much more difficult, if not impossible, without the efforts of the personnel of national mining and geological agencies throughout the world. Information that they collect, compile, and then publish, either in their own volumes or those of central statistical agencies in their countries, are the foundations on which this work rests. Thus, appreciation is expressed to the multitude of persons employed by these agencies.

Jan 1, 1993

By R. Hogg, T. F. Dumm, L. G. Austin, M. Yekeler

"Dedicated to Professor Kurt Leschonski on the occasion of his 60th birthdayAbstractThe kinetics of batch grinding quartz from a feed of 600 by 425 Jim to a product of 80% less than 10 µm have been determined using screening and laser diffractometer sizing for size analysis. The specific rates of breakage decreased by a factor of about three when the material became less than about 100 µm in size, but the primary breakage distribution function also changed to give proponionately more fine material, so that the grinding efficiency expressed as the development of surface area (B.E:T.) per unit of energy input did not decrease. Analysis of the shape of the particles in the 2S x 38 µm size range showed that particles of this size produced by roll crushing or by 8 minutes of grinding of a 42S x 600 µm feed were not different but at long grinding times the particles were rounded. This suggests that the breakage mechanism changes to give more chipping and abrasion and less disintegrative fracture. As the material approached the ultrafine size range it adhered to the mill case and there was no further size reduction. However, a technique for striking the mill case to dislodge the particles was successful in allowing further grinding to 400Jo by weight less than 2 µm.1 IntroductionIt has long been known that it is difficult to accomplish ultrafme grinding in a tumbling ball mill. It has been reported [12, 13] that there is no further size reduction after some hours of grinding cement clinker in laboratory ball mills. Austin and Bagga (1] and Shah and Austin [16] have given an analysis of the kinetics of dry grinding in a laboratory ball mill, introducing the concept of a slowing-down factor K, which is the ratio of the specific rates of breakage at some long time of grinding to the normal specific rates of breakage. They showed that this factor decreased as fine material accumulated in the mill charge. Cottaar and co-workers [8-10] showed that the movement of solid in a dry laboratory ball mill was influenced by the fineness of the solid and by the presence of air, and that evacuation of air from the mill caused particle sedimentation and low rates of breakage.The concept of the slowing-down factor has also been used in wet grinding [17, 18]. At very .high slurry concentrations it appears to be correlated with a steady decrease of mill power caused by the build up of a layer of deposit sticking to the mill case. This reduces the effective mill diameter and, eventually, the balls start to adhere in the layer and centrifuge. A decrease of mill power always indicates less lifting and tumbling of the media and, hence, less breakage. However, slowing-down of breakage rates was also observed at lower slurry concentrations where there was no change in mill power."

Jan 1, 1990

By D. Montagna

Large quantities of zinc-base die-cast scrap containing 3 to 4 percent aluminum are presently refined by mixing with other secondary zinc products such as galvanizer dross and distilling in a retort. The Bureau of Mines investigated alternate aluminum removal processes utilizing low-cost fluxes. Basing the investigation on the metallurgical principle that a reactive impurity can be removed from a less reactive matrix metal by melting under a flux consisting of a salt or oxide of a metal less reactive than the impurity, three separate flux mixtures were studied. In the first flux system, [FeCl3] + NaCI (the active component is underlined), part of the aluminum is' eliminated by the formation of volatile aluminum chloride and the rest by the creation of a high melting point iron-aluminum intermetallic compound that can be separated from the remaining molten zinc by filtration. Aluminum removal in the second system, [Fe203] + CaClz + NaCI, is effected by the formation of the iron-aluminum compound and possibly aluminum oxide. The third system, spent sal skimmings--essentially a mixture of [ZnCl2], NH4Cl, and ZnO, depends solely on aluminum chloride formation. Of the three flux systems investigated, the best results obtained were with system 3. Aluminum was reduced in the molten die-cast alloy from 4.10 percent to 0.01 percent when depleted sal skimmings were used.

Jan 1, 1969

By Jr. Watts, B. K. Cantrell, D. H. Carlson, K. L. Rubow

"The use of diesel equipment in underground coal mines is controversial because ""whole diesel exhaust"" is regarded as ""a potential occupational carcinogen"" by the National Institute for Occupational Safety and Health (NIOSH). Threshold limit values (TLVs) are recommended for the gaseous pollutants; CO, CO2, NO, NO2, SO2, and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sampling these aerosols.The University of Minnesota and the Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size selective, inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines using diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine air quality.Air quality data were collected in four underground coal mines using continuous mining methods with diesel haulage equipment. Daily samples were collected at the section intake, haulageway, and on haulage vehicles. Both full-and partial-shift samples were collected using a variety of aerosol instruments, including the PDEAS and the micro-orifice, uniform deposit impactor (MOUDI) which sample the mine aerosol diesel exhaust fraction. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust CO, CO2, NO, NO2, and SO2. These measurements were made by either collecting bag samples for subsequent gas analysis or by Palmes dosimeters.The concentrations of CO, CO2, NO, NO2, and SO2, were well below regulated levels. The mine average DEA concentration determined by the PDEAS in the haulageway for the three mines surveyed using this instrument was 0.79 mg/m3, with a standard deviation of 0.19 mg/m3. DEA contributed 65% of the respirable aerosol, at this location. These results were the same as the mean DEA concentrations calculated from size distribution measurements obtained using the MOUDI. This was 0.78 mg/m3, with a standard deviation of 0.22 mg/m3."

Mar 1, 1992

By R. V. Ramani

"In this paper, the current status of respirable dust control in coal mine atmospheres is presented. The advancements in the engineering control of dust generation and entrainment, and of reducing the exposures are summarized. The results of the Health Surveillance Program are briefly reviewed. The results of research conducted in the Generic Mineral Technology Center for Respirable Dust are presented. The 1995 NIOSH criteria document on respirable coal mine dust is briefly reviewed. The fundamental scientific and engineering issues in need of research are discussed. A detailed bibliography is attached.IntroductionFor coal mines in the United States, the current permissible exposure limit (PEL) of 2mg/m3MRE-equivalent concentration (an 8-hour TWA concentration measured gravimetrically) was established by Public Law 91-173: the Federal Coal Mine Health and Safety of 1969 (the 1969 Coal Act). This standard is reduced when the respirable quartz content in the dust sample exceeds 5%; the reduced standard in mglm3 is obtained by dividing 10 by the percent quartz. The OSHA and ACGIB PEL for respirable coal mine dust is also 2 mg/m3 , and OSHA PEL for respirable quartz is 100 µg/m3 . The 1969 Coal Act also prescribed two activities in the Coal Mine Respirable Dust Sampling Program and the National Coal Workers' Health Surveillance Program n to control respirable dust in mines, and the coal worker's pneumoconiosis (CWP) among the coal miners.There are three principal methods by which personal exposures to respirable dust are controlled. The first is engineering control where the aim is to reduce the concentration in the mine atmosphere to or below the mandated level. The second is the provision of personal protective devices which allow the miner to work in dusty atmospheres without increasing personal exposure. The third is the use of administrative controls where the miner's exposure is controlled through work schedules and procedures to keep miner exposure at or under the mandated levels. The 1969 Coal Act specifically prohibits the use of respirators in lieu of environmental control. The compliance sampling program essentially does not give any credit to the use of administrative controls."

Jan 1, 1998

By R. H. Sprute

This report describes a feasibility study to consolidate coal waste sludge in a 100-acre pond by applying direct current between floating and buried electrodes. The study was conducted by the Bureau of Mines under a cooperative agreement with Washington Irrigation and Development Co., located near Centralia, Wash. Part 1 covers results of laboratory tests at the Bureau's Spokane Research Center and a small-scale field test at the cooperator's coal preparation plant in western Washington. The process is efficient and cost-effective when power is applied at low current density. A proposed system, fully described in part 2, has electrodes covering 21 acres of pond surface radially arranged around a central power platform. Densification of pond contents would require 2 to 3 years of treatment. Total cost of equipment, labor, and material is approximately $500,000.

Jan 1, 1982

By Fred A. Williams

The cause of many deaths and extensive property damage in coal mines resulting from explosions and mine fires has been directly attributable to electric cable failures (including splice failures). The Federal Bureau of Mines data show that out of 355 underground coal mine fires investigated from July 1952 to January 1960, 103 (29 percent) were directly related to trailing cables. These cable failures resulted in the death of 7 men and injuries to 37 others. These potential hazards have become greater, obviously, through the widespread adoption of mechanized mining methods with electric-driven machinery powered through trailing cables according to Young,4 68.1 percent of the total bituminous and lignite production of the United States was mined underground in 1959. About 85 percent of this production was attained by mechanized loading methods. A large majority of the mines using the hand- loading methods also used equipment with trailing cables such as cutting machines, drills, and gathering locomotives. The problem of minimizing the loss of life, resources, and equipment from cable failures should be of concern to the management of all coal mines. It would be misleading to imply that no consideration has been given to the problem and its associated hazards. Through research cable manufacturers have endeavored to develop trailing cables that will withstand the severe service imposed by underground mining conditions. Technical research groups have undertaken studies for determining improved procedure and materials for field splices. Coal companies have instituted cable maintenance programs with a view toward the reduction of cable failures and consequent improvement in safety and efficiency of operations. Safety agencies are alert to unsatisfactory cable handling practices, poor workmanship in field splicing, mechanical

Jan 1, 1962

By Ronald H. Church, Walter E. Pittman, J. T. McLendon

In its role of providing technical assistance to the mining industry, the Bureau of Mines' Tuscaloosa Research Center has conducted research to develop trapped miner location systems which would aid in locating miners trapped by underground mining disasters. Efforts to produce electromagnetic systems for the location of trapped miners underground and to communicate with them were surveyed, from the 1920's to 1981. Theoretical studies of through-the-earth electromagnetic transmissions are described as well as studies of the electrical characteristics of various rocks, minerals, and soil. Several trapped miner location systems are reviewed including the Westinghouse systems, the DEVELCO system, and an automated three-dimensional location system, and the phase difference of arrival technique. Tangential research, relevant to trapped miner location systems is described. A comprehensive bibliography covering all aspects of trapped miner, through-the-earth electromagnetic location and communications systems is appended.

By Raymond J. Isherwood

The U. S. Bureau of Mines has investigated the domestic primary and secondary lead smelting and refining industries to determine the economic impacts of existing and proposed environmental, health, and safety regulations. The impacts are assessed in terms of capital and operating costs for existing and alternative smelting/ refining technologies. Industry response to regulatory implementation is estimated and quantified in terms of import value from lost lead production. For the primary lead industry, regulatory compliance may add up to 1.15 ¢/lb refined lead to operating cost for rehabilitated plants. Alternative smelting/refining methods could reduce net operating costs by as much as 4.36 ¢/lb refined lead. Capital expenditures would vary from $750 to $1,000 per annual mt of smelter capacity. Secondary lead smelter operating costs would increase about 3.8 ¢/lb refined lead to comply with existing regulations. Capital expenditures would average about $124 per annual mt of smelter capacity. Implementation and enforcement of proposed regulations would result in closure of the primary lead industry and additional expenditures for compliance by the secondary lead industry. Enforcement of the most extreme proposed regulations would force the secondary lead industry to close.

Jan 1, 1988

By d&apos, Kathleen J. Amico

THIS SUAMMARY is shown in Minerals Yearbook volumes I and III of this series on mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, and on the principal minerals imported into and ex- ported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1962

By H. C. Brunaugh, James Westfield, R. W. Whittaker

"INTRODUCTION The purpose of this circular is to describe the sealing off of a mine fire and subsequent use of carbon dioxide gas to extinguish it.A fire of electrical origin occurred in the Valier mine of the Valier Coal Co., Valier, Franklin County, I11., on March 29, 1949, at about 1:35 p.m. It was discovered about 3:35 p.m. in 5 south west intake airway inby 1 and 2 west panels. The No. 5 southwest airway had caved, and the fire was in the top coal beneath a large fall of rock. All men, except officials, were ordered from the mine. The mine officials decided to seal the fire, and four temporary seals were erected, which isolated approximately 200 feet of 5 south west entry. The seals were completed on March 30 at 2:45 a.m., but on March 31, at 3;40 a.m,, two of them were blown out by an explosion of gas that was produced by the fire. The two seals were rebuilt, the work being completed on March 31 at 12:00 noon, but they were blown out by another gas explosion at 12:10 a.m. on April 1. It was then decided to extinguish the fire with water if possible.To accomplish this, concrete-block dams were constructed. On April 1, about 4:25 a.m., when the dams were about half completed, water was introduced into the fire area through a 2-inch pipe.On April 4, J. G, Crawford, general manager of the Valier Coal Co., notified James Westfield, chief of the Vincennes (Ind.) Branch, U. S. Bureau of Mines, by telephone of the fire in Valier mine and requested assistance to combat it. Westfield, accompanied by F. J. Smith and H. C. Brumbaugh, Federal coal-mine inspectors, went underground and inspected the seals and dams. Later, during a conference with company officials, it was decided that the concrete-block dams were not strong enough to withstand the hydrostatic pressure that would be produced by flooding the fire area. It was then decided to use carbon dioxide gas to extinguish the fire. Four seals were completed, and 5 tons of carbon dioxide gas was introduced into the fire area, which extinguished the fire."

Apr 1, 1950

By R. S. James, E. J. Gleim

Not long after electrically driven equipment was introduced into coal mines it became apparent that the spark-producing parts, such as controllers and motors, required safeguards to prevent the ignition of mine gas that might come into their vicinity. Many of the early designs attempted to provide protective enclosures having ventila¬tion and relief for pressures if ignition should occur within. The principal feature of the Davy safety lamp, namely, the wire gauze, was employed widely for this purpose. Other devices were developed to reduce the temperature of products of combustion escaping through the protected openings to a value below that which would cause ignition of surrounding explosive atmospheres. Although many such devices performed their intended function satisfactorily under laboratory conditions they were not so satisfac¬tory when subjected to the rigorous conditions encountered under¬ground. Corrosion, mishandling, and accumulations of grease and dirt reduced or destroyed their protective qualities after a period of service in the mines. In the United States this has led to abandon¬ment of special devices in favor of what is called " total enclosure " which means that no regular provision is made for ventilation and release of pressure but rather that the housings or enclosures are built strong enough to withstand the explosion pressures without rupture. As a further protection the joints usually are made of broad, closely fitting surfaces. It is impractical to make such joints absolutely gastight in ordinary machine practice when provision must be made for partial or complete disassembly to facilitate ad¬justments and repairs. Therefore, when an explosion occurs within such enclosures flames may escape through the joints. If the latter are broad enough and not separated too widely, however, the flames will be cooled by contact with the metal surfaces (flanges) of the joints, by rapid expansion, or by both cooling and expansion, with the result that an explosive atmosphere surrounding the enclosure will not be ignited. This is termed " flange protection." In testing parts of cutting machines and other equipment for coal mines, with the ultimate object of approving the equipment for use

Jan 1, 1935