Search Documents

By R. L. Levens

The Underground Injection Control program was promulgated in 1981 by the U.S. Environmental Protection Agency under the provisions of the Safe Drinking Water Act. Placement of mine waste backfill underground is considered underground injection under the provisions of this program. A major issue is whether mine waste that is regulated as a contaminant source on the surface should be disposed of underground. The U.S. Bureau of Mines conducted research to investigate the impacts of mine waste sandfill on the quality of ground water. Analyses of water samples collected before and after contact with sandfill in a 10-year-old stope, as well as samples of the sandfill itself, were used to ascertain the influence of the sandfill after mine closure and subsequent flooding. Computer models supported the hypothesis that oxidation of pyrite by oxygen, accompanied by dissolution of carbonates, was the predominant reaction controlling the quality of the water being discharged from the stope. Concentrations of metals released as a result of acid production remained near or below detection limits. Metals release after mine flooding is expected to remain low as a result of the buffering by the sandfill and the reduced rate of oxidation.

Jan 1, 2010

By Kenneth H. Johnston

For the past several years, Bureau of Mines petroleum engineers have arranged tours of selected waterflooding projects for the spring meetings of the Kansas-Oklahoma Waterflood Association. These tours are conducted to demonstrate unique operating methods and new field equipment and to provide additional opportunities for exchanging information. Each of these tours has been supplemented by a published report describing in detail the projects visited. This report has been prepared for distribution during the 1960 spring tour of four waterflooding projects in Greenwood County, Kans. (fig. 1). Three of the projects produce oil from the Bartlesville sand, and one produces from the Cattleman sand. The Bartlesville-sand floods have been in operation from 4 to 12 years and have produced about 3,910,000 barrels of waterflood oil from the injection of approximately 64,715,000 barrels of water, a cumulative water-injected to oil-produced ratio of 17 to 1. The Cattleman- sand flood, which has been operating for 3-1/2 years, has produced about 842,000 barrels of waterflood oil from the injection of approximately 9,305,000 barrels of water, a cumulative water-injected to oil-produced ratio of 11 to 1.

Jan 1, 1960

By H. M. Thorne

The Union of South Africa has been interested in oil shale for a long time, and deposits of oil shales, torbanites, and similar rocks have been found in many parts of the country. (Fig. 1.) Samples differ markedly in oil yield and in the characteristics of the oil. The strata vary in thickness, and most of the deposits that have been found are in unfavorable locations because of remoteness from markets or absence of transportation facilities. This report deals mainly with the torbanite deposit near Ermelo, Transvaal, in the Union of South Africa, and the operations of the South African Torbanite Mining and Refining Co., Ltd. (hereafter referred to as Satmar), in mining the torbanite, retorting it, and refining the crude oil.

Jan 1, 1954

By Staff

A major emphasis of the U.S. Bureau of Mines is to perform research on the prevention of fatal accidents at mining operations. The leading cause of fatalities in the underground coal mining industry is groundfalls. This proceedings volume presents several new developments that are helping to prevent fatalities and reduce injuries by groundfalls. The papers focus on the problem from two different perspectives. About half of the papers present information and techniques that can be used to train and motivate miners to protect themselves from groundfalls. The other papers explain how to identify and respond to various geologic conditions that affect the stability of the mine roof. Of the 95 groundfall fatalities that occurred during 1986-90, 75% took place in Kentucky, West Virginia, and Virginia. The rate of groundfall fatalities was much higher at small mines. During 1986-90, the rate of groundfall fatalities at mines employing fewer than 20 people was 4.3 times higher than the rate for larger mines. Because so many groundfall fatalities are occurring at relatively small mines in the southern Appalachian coalfields, many of the papers focus specifically on the needs of this category of mine operations.

Jan 1, 1992

By Joseph M. Pugliese

This work was done by the Bureau of Mines to provide quarry operators with an uncomplicated, first-approximation method for designing blast patterns, considering geologic structure, and to show the valid use of the technique by comparing drill and blast pattern dimensions used in the quarry with those determined by the presented method. The author visited 12 limestone and dolomite quarries in Ohio (Adam, Crawford, and Highland Counties), Wisconsin (Milwaukee, Racine, and Waukesha Counties), and Minnesota (Fillmore, Olmsted, and Wabasha Counties); observed the blasting practices; studied the major geologic features; and after discussion with the quarry managers, foremen, and blasters, compared the quarry blasting patterns with those as calculated by the empirical formulas (after R. L. Ash), with geologic structural considerations. When geologic structure such as bedding, jointing, folding, and caves, as well as explosive properties and field performance characteristics are accounted for in a manner suggested by the research, the presented empirical formulas may be used as a good first approximation. The included steps in planning a blast design and generalized blast patterns should be of help to the quarry operator. Design changes are recommended for those quarries where problems are occurring.

Jan 1, 1972

By D. K. Deardorff

The hafnium-vanadium phase diagram was constructed within an estimated accuracy of ± 10° C and ± 2 wt pct composition. Alloys for investigation were melted under an atmosphere of purified helium by nonconsumable tungsten-electrode arc melting on a water-cooled copper hearth. Melting points were determined by optical pyrometer, and the remaining phase relationships were investigated by metallography, thermal analysis, and X-ray diffraction. The existence of a face-centered cubic intermetallic compound HfV2 (a = 7.38 A) was confirmed. A eutectic reaction occurred at 20 wt pct vanadium and 1,395° C to yield HfV2 and 8 solid solution. HfV2 melted incongruently by a peritectic reaction at 1,480° C, and the 3 solid solution decomposed eutectoidally at 1,165° C and 6 wt pct vanadium to yield HfV2 and a solid solution. The eutectoid, the eutectic, and the peritectic isotherms extended from 1 to 36.3 wt pct vanadium, from 8 to 36.3 wt pct vanadium, and from 26 to 89.5 wt pct vanadium, respectively. Terminal solid solubilities of hafnium in vanadium at 1,300° C and of vanadium in hafnium at 1,100° C determined to be about 3 and 1 wt pct, respectively.

Jan 1, 1965

By J. W. Adams

This report surveys the efforts of six contractors to the U.S. Bureau of Mines with regard to their electromagnetic noise measurement programs. What has been done, what is planned, and evaluations and recommendations are given for each contractor. The main observation is that to date there is not sufficient knowledge of electromagnetic interference in mine environments to design a reliable communication system. This knowledge should be available by the end of June 1972 if certain planned programs are completed successfully. A major effort of this report is to establish parameters to be measured, units to be used, and workable formats for data presentation. This is given in Appendix A. Some details concerning equipment, procedures, locations, and sample data are included in Appendix B.

Jan 1, 1971

Research 83 highlights significant studies conducted during the past fiscal year at Bureau facilities and offices. Readers who want more information about the projects and studies summarized here can contact the researchers whose names and locations appear with each summary, General information on Bureau of Mines programs is available from the Office of Technical Information, 2401 E Street, NW., Washington, DC 20241. A listing of principal officials, a location map of field facilities, and a selected bibliography of publications and patents issued on Bureau developments during the past 3 years are provided.

Jan 1, 1983

By Stephen M. Jasinski

This report describes the materials flow of mercury in the United States. It examines the mining and production of mercury and the manufacturing, uses, and ultimate disposal of mercury. Materials flowcharts were prepared for 1989 and 1990. An effort was made to include estimates for all major anthropogenic sources including fossil fuel combustion, waste incineration, and nonferrous metal mining operations. Mining and mineral processing released about 100 mt/yr of mercury to the environment in both 1989 and 1990. The combustion o ii fu1s released 175 mt/yr in the same years. The manufacturing, use, and disposal of products containing mercury accounted fix the release of 1,037 mt of mercury in 1989 and 938 mt in 1990. The manufacture of chlorine and caustic soda was a major source of recycled mercury, but it was all reused within the industry. Recovery from all waste products accounted for 36% of reported consumption in 1989 and 42% in 1990. The losses from manufacturing and end use have been declining, whereas mercury emitted from combustion sources has not been strictly regulated and will likely become the largest source of mercury releases to the environment.

Jan 1, 1994

By P. G. Guest

Many of the gases and vapors used in anesthesia form explosive mixtures with oxygen or air. Sources of ignition for these mixtures always have existed, in operating and anesthetizing areas. When ether was first introduced, candles and gas-lights and coal stoves caused fires and mild explosions of the vapor-air mixtures. Today the chief causes of ignition are electrical. Fires and explosions are still much too frequent; and, because many of the mixtures are rich in oxygen, the explosions sometimes are very violent. Obvious sources of ignition, such as electric-power sparks and arcs in open motors, switches, and receptacles, as well as exposed incandescent wires and hot plates, usually are recognized by hospital personnel and corrected. A source of ignition that is not so obvious to many is static electricity. Until quite recently the presence of this hazard in a large majority of anesthetizing areas was not even suspected. However, numerous explosions -many of them fatal to patients -have been attributed, with good reason, to sparks from static electricity. In this paper the authors present facts to show the prevalence of static electricity in the average hospital anesthetizing area, and the degree to which this easily developed electrical form of energy constitutes an explosion hazard. An effort is made throughout to explain how static electricity behaves, why it is a hazard, and why certain safety measures are needed and recommended. Following the introduction and a short general discussion of static electricity, which incorporates a glossary of pertinent electrical terms, an account is given of inspections and tests made in a number of hospitals. This account includes many suggestions that should be useful to any person who plans to make similar inspections and tests. However, a comparison of materials and equipment used with those described in the report will reveal, in many cases, the potential dangers and obviate the necessity for tests. The hospital work was supplemented by considerable laboratory research designed to determine the spark energies required to ignite anesthetic-gas mixtures and the exact amount of time involved in developing the usual static charges. The results of this research are reported and the implications examined. The paper concludes with a general discussion of static and related hazards in anesthetizing areas and of the most urgent preventative measures.

Jan 1, 1952

By Patrick D. Plumb

The Bureau of Mines (BOM) has begun a project to increase the understanding of the relationships between ecosystem health and its functions, and minerals development. The BOM, Juneau Branch, Alaska Field Operations Center, is providing support for ecosystem based land-management decision-making and the development of ecosystem based regulations by documenting the effects of mining on ecosystems and demonstrating the tools used to assess and analyze those effects. This is done by reviewing the data available on ecosystems and the environment at a mining site, the Greens Creek Mine near Juneau, Alaska, and applying available Geographic Information System modeling tools to assess the impacts of the mine on components of the pristine ecosystem. Habitat Capability Models for wildlife indicator species are used in this examination. Wildlife indicator species are used as indicators of ecosystem health by the U.S. Forest Service and the Alaska Department of Fish and Game, who developed these models for southeast Alaska. Analysis techniques from the U.S. Fish and Wildlife Service's Habitat Evaluation Procedures (HEP) are also used in this report. By applying available models and analytical techniques to the Greens Creek area, the benefits gained through mitigation of potential impacts become apparent. These or similar techniques are useful for cost/benefit analysis of mitigation alternatives. Also apparent from this analysis is that the degree to which potential impacts are observable will depend upon the ecosystem scale considered. This demonstrates the importance of defining the ecosystem and scale before performing impact and cost/benefit analysis. The watershed scale is found to be useful for assessing impacts to ecosystem components at the Greens Creek Mine. Much progress remains to be made in the modeling and prediction of impacts to ecosystems from mining activity.

Jan 1, 1994

By Robert L. Lagace

A prototype adaptive volume control for the loudspeaker output of mine trolley carrier phones was designed, built, and tested in the laboratory and in a mine. This volume control senses, and adapts to, the ambient acoustic noise environment in such a way as to produce a loud sound output under noisy conditions, and a quieter output under quiet conditions, thereby producing an understandable and unstartling volume level under all noise conditions. The design approach, prototype hardware, and test results are described, and the device is shown to be feasible for in-mine operations. The circuit design principles are easily applicable to currently available mina trolley carrier phones. Recommendations for practical improvements are included. An in-mine experiment to assess the practical feasibility and utility of the dedicated wire technique for overcoming poor trolley carrier phone system performance was designed, performed, and evaluated. The technique involves the use of a single, low-loss, properly terminated auxiliary wire, placed in the rail haulageway, which allows signals to naturally couple to and from the trolley wire/rail transmission line, and thereby significantly decrease the overall signal attenuation rate on the trolley wire/rail line. The in-mine dedicated wire experiment, results, and conclusions are described, and the technique is shown to be a valid and practical one for significantly Improving carrier phone system performance in mines. Guidelines for the installation and use of the dedicated wire are provided. Recommendations are made for obtaining further practical information on its performance and utility. A second in-mine experiment to assess the feasibility and utility of the low-impedance (low-Z) line technique for overcoming poor carrier phone signal transmission in mines was designed, performed and evaluated. The low-Z line technique involves the periodic connection of shunt capacitors between the trolley wire and the rail to artificially lower the line characteristic impedance. This causes the low impedance shunt loads encountered across the trolley wire/rail line to be less mismatched to the line, thereby reducing the overall attenuation of carrier phone signals. The results of in-mine experiments performed along unenergized and fully operational sections of trolley wire/rail line are described. The experiments were designed to measure line parameter such as inductance and capacitance per unit length, characteristic impedance, and propagation phase velocity, in addition to signal strength versus distance behavior under normal and low-Z line conditions. The low-Z line technique is shown to be valid, but not as practical as the dedicated wire technique which is recommended as the most favorable for most coal mine applications.

Jan 1, 1979

"Research on the control of exposure to respirable contaminants in mine atmospheres is conducted in five areas; 1) control of dust generation, 2) dilution, dispersion and collection of dust in mine airways, 3) characterization of dust particles, 4) interaction of dust and lungs, 5) relationship of mine environment, geology, and seam characteristics to dust generation and mobility. The distribution of research findings to the mining industry, to government agencies, and to scientists at other universities is accomplished in several ways.A data bank of respirable dust samples displaying a wide range of characteristics (low volatile, medium volatile, high volatile, silica fireclay, rockdust) has been established by the Center. This data bank is being utilized by Center researchers in a suite of medical, scientific, and engineering tests (FIGURE 26).The Center has honored requests for educational and informational materials from several sources, including MSHA and CANMET who received information on Center generated software and used the Center's expertise in developing a computer program for particle distribution model (DISFIT).The Generic Mineral Technology Center for Respirable Dust has organized two dust conferences on respirable dust, the Coal Mine Dust Conference, held at West VirginiaUniversity, Morgantown, West Virginia from October 8-10, 1984 and Respirable Dust in the Mineral Industries: Health Effects, Characterization and Control, an international symposium on Respirable Dust in the Mineral Industries held at The Pennsylvania State University, University Park, Pennsylvania from October 14-16. 1986. These conferences were co-sponsored by the U.S. Bureau of Mines, Mine Safety and Health Administration, National Institute for Occupational Safety and Health (NIOSH), and the American Conference of Governmental Industrial Hygienists (ACGIH). On August 23-26, 1988, the VIIth International Pnuemoconioses Conference was held in Pittsburgh, Pennsylvania. While not a sponsor of this conference, researchers in the Generic Mineral Technology Center for Respirable Dust had significant participation with sixteen (16) papers presented (see Volume 8 of this series for abstracts and papers). These conferences provided a significant forum for the exchange of ideas on dust research and the interchange of research findings. The proceedings from these conferences are available from NTIS and ACGIH.In sum, significant benefits to mine worker health have resulted and should continue to result from the synergistic scientific, engineering, and medical research in respirable dust (FIGURE 27). As always, an important objective is the rapid dissemination of the results of this research to industry. Video tapes and the Bureau's Technology News series have been a very effective means of USBM technology transfer. Individual no-cost subscriptions to the Technology News series are available from the U. S. Bureau of Mines, Branch of Technology Transfer, 2401 E Street, N.W., Washington, DC, 20241."

Aug 31, 1989

By N. L. Wimmler

The Metaline mining district was examined in 1942 by Bureau of Mines engineers with the cooperation of geologists of the Federal Geological Survey. Because the demands of war production were rapidly depleting reserves in some of the older zinc-lead producing districts of the United States, it was decided that an attempt should be made to increase the proved or indicated ore reserves of the Metaline district. With this objective, certain areas to be explored by diamond drilling were selected. The Bureau of Mines began work on this program. January 15, 1943; work terminated September 8, 1945. Forty-five holes were drilled in seven areas, The holes ranged from 154 feet to 2,050 feet in length. Their combined length was 38,150 feet. Thirty-three of the holes were drilled in. the North Pend Oreille and the West Bella May areas.

Jan 1, 1949

By M. W. Von Bernewitz

Because the cutting and polishing of stones are parts of the work of the Bureau of Mines in its study of rocks and minerals and in the determination of specimens sent in for identification, it was decided that a circular covering the subject in a general way would be of practical interest. As several books and periodicals give details of the problems in cutting and polishing, this report will not duplicate their information more than necessary. ACKNOWLEDGMENT The manuscript for this circular was read by Oliver Bowles and Forrest Moyer, Building Materials unit, Bureau of Mines, who supplied some of the illustrations; several photographs were taken by Howard Carl, Optical Section, Bureau of Mines. Equipment firms that y contributed information and publishing houses whose books have been abstracted are mentioned in the text.

Jan 1, 1940

By Edward L. McHugh

The appraisal of mineral resources of the Challis National Forest, Idaho, by the U.S. Bureau of Mines, was made so that the mineral resources of the forest could be appropiately considered in land use planning. Information from this study is intended to tip the U.S. Forest Service to incorporate mineral resource data into forest plans The study was done in conjunction with the U.S. Geological Survey, which released a companion report on the geology and mineral potential of the Challis National Forest in 1989. This summary report is derived from a more detailed USBM Open-File Report (MLA 6-91) that includes descriptions of mines and prospects, commodity profiles, and development cost models. Since the 1860's mines within the Challis National Forest have produced mineral commodities worth more than $590 million at current (1989) commodity prices. Identified mineral resources have a gross value of about $2 billion at current prices, including 8 strategic or critical minerals. The U.S. Bureau of Mines study identified and described 723 active and inactive mineral properties within the forest. Mineral properties with identified resources were evaluate to determine their economic significance, and an assessment was made of the feasibility of mineral development. Of the 2,516,191 acres in the Challis National Forest, about 390,000 acres were classified as having mining development interest. Commercially important mineral production, mainly of molybdenum, gold, and silver from the Challis National Forest is likely for the foreseeable future.

Jan 1, 1991

By James J. Olson

The Bureau of Mines recorded and analyzed overpressure levels for three production blasts at the White Pine copper mine, Upper Michigan, to obtain representative data from single-heading blasts in a long, straight haulageway and to estimate the damage potential inherent in production blasts fired in close proximity to underground structures. Commercial pressure gages with a flat response to 1 kHz were used with an FM tape recorder to record the overpressures from one dynamite and two AN-FO (ammonium nitrate-fuel oil), 500-msec production blasts having zero-delay charge weights of about 75 lb (34 kg). The recorded waveforms from the underground blasts (1) were more complex than the typical free-air wave, (2) were of longer duration, and (3) had numerous secondary arrivals due to reflections from the ribs and roof. The waveforms showed that the zero-delay charges produced the only high overpressures. First pulse peak overpressures from the blasts ranged from 0.10 lb/in2 (6.9 X 102 N/m2) at a distance of 471.1 ft (144 m) to a maximum of 1.76 lb/in2 (121.3 X 102 N/m2) at 191,7 ft (58.4m) from the blasts. An analysis of variance of the first pulse overpressures from the three White Pine blasts showed that no statistically significant difference existed among the overpressure levels from the dynamite and AN-FO blasts and that a single equation P = 4.9 x 103 (D /W1 / 3) 2 .15, where P = overpressure in pounds/inch2, D = d-stance from the blast in feet, and W = zero-delay charge weight in pounds, could be used to describe the falloff of overpressure with distance.

Jan 1, 1971

By J. R. Soule

"The fluorspar deposits in the Gallinas Mining District, Lincoln County, New Mexico, were examined early in February and again in April 1943 by the Bureau of Mines because of the possible importance of newly discovered deposits and of old mine workings showing fluorite-bearing material. There &re many of these deposits spread over a considerable area, and it appeared that exploration might indicate sufficient reserves to support a local mill that could contribute to the supply of fluorspar needed for war purposes. Accordingly, the Bureau initiated an exploratory program in June 1943, which was completed in August 1944.H. E. Rothrock, Roy Earhart, R. G. Smalley, and V. C. Kelly, geologists of the Federal Geological Survey, began mapping and studying the district in May 1943 and continued this work throughout the Bureau's exploration.David J. Stauffer, district ranger, U. S. Forest Service, and several claim owners assisted in the examinations and subsequent exploration.The fluorspar deposits in the Gallinas Mountains are reached by an unpaved forest road, which, leaves U. S. Highway 54 half a mile south of Gallinas station. The road runs due west for 3 miles, then turns due north just beyond the first cattleguard. This north branch is followed for 2 miles to a second cattleguard. There a left branch extends northwest up Red Cloud Canyon to the Red Cloud, and. All. American deposits; the right branch continues north for 2.miles past the Wade Porter ranch, to another left branch, which goes almost 2 miles west to the Hoosier Group deposits. The remaining deposits are reached by trail from either the Hoosier Group or, more easily, from the Red Cloud claim (fig. 1).The Hoosier Group is in sec. l9,, T.. 1S.,1 R. 12 E.; all of the other known ore occurrences are in secs. 13, 14, and 23 to 27, inclusive, T. IS., R. 11 E. All of the deposits are in the Lincoln National Forest and within the limits of a State game refuge. The nearest railroad loading point is Gallinas, Station on the Southern Pacific Railroad. Corona, the next station north of Gallinas, is a Mile or two farther from the deposits.Minor supplied, telegraph, telephone, freight, and express service, and limited living accommodations, Are, obtainable at Corona, 10 to 15 miles from the deposits of Carrizozo, N. Mex., 50 miles south."

Apr 1, 1946

Study to develop a new and more cost effective equipment system, incorporating a winch-pulled dozer blade, for leveling spoil and performing reclamation of area strip mines.

Jan 1, 1975

By James P. Ludwig

This report provides the results of a two year study of the projected time and cost requirements for new mine development in Wisconsin and is based on a unique blend of information from mining company officials, state regulatory agency officials and contractor experience. Through formal cooperative and review agreements with Kennecott Copy per Corporation, Exxon Minerals Co., U.S.A. and Noranda Mines Ltd., and the Wisconsin Department of Natural Resources plus informal arrangements with knowledgeable Wisconsin persons, lists of the tasks and subtasks required to plan a new mine in Wisconsin were developed. Times and costs were assigned to all tasks and subtasks and these data reviewed by all cooperators. Critical Path Method Diagrams were then developed for a generalized mining project. Total time and cost for the premine planning process was estimated to be 25..1 years and 223 person-years of professional time excluding public affairs effort respectively. By eliminating redundancies in the process and by increasing project efficiency through early public review and participation, recom¬mendations were made to lessen the time and lower the cost of premine planning. The streamlining recommendations could shorten the overall critical path length to 18.16 years and lower the cost to 208 person-years of professional time excluding public affairs effort. The estimated distribution of professional effort (cost) for mine planning in Wisconsin approximates 50.5% for traditional mine engineering tasks, 36.6% for environmental-regulatory tasks and 12.9% for traditional geological-exploration tasks.

Jan 1, 1979