Search Documents

By W. P. Diamond, F. Garcia, J. K. Marshall

Many longwall mines rely on methane drainage to supplement traditional fan-based ventilation systems. However, the surface production facilities for methane drainage systems, including gob gas ventholes, are commonly located in remote locations, sometimes without convenient access to electrical power, and they may be monitored infrequently. The first evidence that a methane drainage system may not be operating efficiently, or not operating at all, can be an increase in methane concentrations at a return air shaft or underground where the workforce is exposed to the risk of a methane explosion. A solar powered, remote gob gas venthole monitoring and cellular telephone-based real-time data transmission system has been developed and successfully field tested by the National Institute for Occupational Safety and Health (NIOSH) to address this problem. With this system, individual methane drainage boreholes can be monitored from the mine office to determine current operational performance parameters, as well as review past data to anticipate maintenance needs and troubleshoot operational problems.

By G. David Baskin

Changes in the 1978 quantity and value of the sales of various natural abrasives, compared with the data for 1977, were of a mixed nature. Output of tripoli-type materials and garnet increased in both tonnage and value. Emery production also increased. But special silica stone product sales decreased in both tonnage and value, and the reported quantity and value of sales of manufactured abrasive material also decreased for 1978. In 1979 output of tripoli-type materials and special silica stone products decreased in both tonnage and value when compared with the previous year. The tonnage and value of sales of garnet and manufactured abrasives increased when compared to 1978 data.

Jan 1, 1980

This sheet explains your audiogram (hearing test) and gives some basic information about protecting your hearing. Keep it so you can refer to it later. What is an audiogram? • An audiogram is often called a “hearing test,” but there’s no pass or fail • It is a written record of your hearing levels • A series of audiograms can track changes in hearing over time • Your hearing threshold levels (the quietest sounds you can hear) are measured in decibels (dB) at different frequencies from low (500 Hz) to high (8000 Hz) Why should I get audiograms? • To measure your hearing ability • To identify hearing problems • To monitor success at maintaining your hearing • To see if noise exposure is affecting your hearing Do I have normal hearing? Compare your hearing threshold levels to this scale: -10 – 25dB Normal hearing 26 – 40 dB Mild loss 41 – 55 dB Moderate loss 56 – 70 dB Moderate/severe loss 71 – 90 dB Severe loss 91 – 100dB Profound loss [ ]

Jan 1, 2008

By Gustav Wirth

"ABSTRACTIn exothermic and endothermic catalytic reactions, control of the temperature is of utmost importance. Basic calculations are developed for determining catalyst volumes of various types of reactors that give particular temperature distributions, and the individual designs are compared.INTRODUCTIONA narrow range of permissible operating temperatures characterizes many, catalytic reactions, and yields of the desired product are reduced sharply if operating temperatures fall outside of this optimum range. In order to achieve close temperature control, reactors with internal heat exchange have been developed in which thin layers of catalyst are located between cooling surfaces.The temperature distribution for an exothermic reaction in such a thin catalyst layer is shown in figure 1. Reactive gases flow downward through the catalyst section, which is 2so wide. It is assumed that a constant amount of heat is generated per unit of bulk catalyst volume, and that this heat is entirely removed through the walls. Consequently, except for a short section at the entrance of the reactor, the heat of reaction is not available for raising the temperature of the gases. Thus, at all points equidistant from the axis, the temperature is the same throughout the entire reactor. At the middle of the gas stream, the temperature is designated as uo. Traveling radially from this point, the temperature decreases because of the removal of heat through the walls and reaches, in the vicinity of the cooling surface, the value u1. Over a relatively narrow zone of width, b, the temperature falls to the value u2 at the cooling surface. Because inadequate data are available on heat-transfer coefficients for a gas flowing through a porous bed, and also because the narrow zone, b, is probably without effect on the reaction by virtue of its low temperature, the temperature drop in this zone at the cooling wall was disregarded. The following calculations were made on the basis of the temperature drop (u0 - u1) resulting from heat conduction within the main body of the catalyst bed only."

Nov 1, 1950

By William H. Schiffbauer

One of the safety and health research programs of the former U.S. Bureau of Mines Pittsburgh Research Center was the evaluation of technology that will provide remote-controlled operation of mechanized equipment in underground room-and-pillar mining. The purpose of this effort was to enable workers to be located away from the hazardous and unhealthful coal extraction area (the face). As part of this program, advanced machine navigation and control technologies were developed for underground room-and-pillar and highwall coal mining that can be applied to commercially available mining equipment. These technologies use off-the-shelf components and a flexible control software architecture to minimize the effort required to adapt them to mining equipment. An accurate, reliable navigation system that can provide the mining machine's heading and location is a critical requirement for a remote-controlled mining system. After investigating several different types of navigation sensors, researchers selected the Honeywell Ring Laser Gyro Inertial Navigation System (INS) as showing the most promise. It was installed on a continuous mining machine at our Mining Equipment Test Facility. Extensive testing at an open pit (OP) site was also performed. This report describes the INS as it was employed on the mining machine in the laboratory, in the field, and OP tests, and provides the accuracy and performance results of the OP and highwalltests.

Jan 11, 1997

The development of the potential supply analytic system has advanced to the point that quantitative estimates of economically recoverable resources can be made as the final step of the traditional regional mineral resource assessment process. In 1983, the BOM and the ADGGS jointly developed a methodology to quantitatively assess the potential for undiscovered yet economically recoverable minerals within a designated geographic area. This methodology was first applied in the assessment of the undiscovered mineral potential of the Kantishna Hills, Alaska (White et al., 1987). At that time the assessment procedure combined a series of technical judgements regarding the major geologic, engineering and economic factors that influenced the occurrence and exploitation of mineral resources in the Kantishna Hills area. Since then the methodology has been further developed and enhanced, particularly with respect to the engineering and economic analysis components. The resulting Potential Supply Analysis System (PSAS) was recently used to evaluate the economic potential of selected types of undiscovered precious-metal deposits in the Tonopah quadrangle of Nevada (Gunther, et al., 1988) and, with some enhancements, has been used to estimate the' economic value of the undiscovered mineral potential of the WMNRA/SNCA study area. The PSAS has been designed to address five basic questions about the mineral potential of an area: 1) What alternative states of geologic nature are possible in the area of interest (e.g. How many and what types of undiscovered deposits could be present and what might be their grade, tonnage and depth attributes?) ?;

Jan 1, 2011

By Thomas M. Barczak

The initial Support Technology Optimization Program (STOP),Version 1.0, was released at the 19th Ground Control Conference. This original program has since been updated to Version 2.3 which was released in May, 2001. This paper describes the additional features of Version 2.3, focusing primarily on the following three aspects: (1) including uncontrolled convergence into the design requirements for standing roof supports, (2) the addition of design procedures for cable bolts as an alternative secondary roof support, and (3) the addition of new standing roof support technologies. Another new feature which should facilitate the development of design criteria for standing roof support is the capability to define ground reaction curves through convergence measurements alone without having to make support loading measurements. There are several other new features provided in Version 2.3 which are only briefly addressed in the paper. These include: (1) additional graphics capabilities to facilitate rapid assessment of support comparisons, (2)an East-West designation for support selection to more accurately provide cost and support availability data, (3) additional safety measures including a safety factor to identify support design near the peak support capacity, checks to see if the support dimensions comply with aspect ratio requirements, and a measure of roof coverage for the design layout of the support system. These new features of STOP provide more capabilities to design and analyze secondary roof support systems for conditions which could not be fully analyzed in the original version of the program.

By Richard Lusignea

A single boom roof bolting machine was outfitted with measurement and recording systems for detecting changes in machine parameters while drilling. The purpose of this instrumented bolter or "smart drill" is to detect changes in roof conditions from the machine parameters of penetration rate, thrust, rotation rate, torque, rejected light from rock cuttings, and vibration of the roof during drilling. The system was demonstrated underground in coal mine conditions and showed correlation between rock type and drilling parameters.

Jan 1, 1982

By W. A. Calhoun

The purpose of this investigation was to develop economical mineral dressing processes for removing objectionable quantities of impurities, such as quartz and pyrite, from refractory clay deposits in east central Missouri. The presence of excessive quartz in these clays causes crazing. Pyrite causes bloating and unsightly dark blobs on the surface of fired refractory brick. The iron concentration in the proper state of oxidation may also act as nucleation centers for carbon crystal growth which can result in bursting of the refractory. Numerous deposits, representing a very large tonnage, have been examined and prospected by various refractories companies and found to contain impurities in objectionable quantities. Upgrading these clays would greatly extend our reserves of high-quality refractory clays. Wet-tabling and wet-cyclone concentration were found to be effective for removal of impurities from clays. Of the two methods, wet-cyclone concentra¬tion would be cheaper and more effective. Although wet-tabling improved the refractory properties of each clay, beneficiation by wet-cyclone produced clays of superior quality. Clay recoveries by wet-cycloning ranged from 56.1 to 81.8 percent of the weight of the crude samples, and the beneficiated clays contained from 71.9 to 94.4 percent of the total alumina. The pyrometric cone equivalent (PCE) was increased from 1 to 3 cones by wet-cycloning. The beneficiated clays also met the reheat shrinkage requirements on refiring to 1,400° C. Missouri is one of the major domestic sources of fare clay. In addition to deposits of high-grade refractory clays, there arc many deposits that contain small percentages of impurities, which render the clays unfit for the production of high-heat-duty firebrick. Development of methods to beneficiate these submarginal clays to usable materials would greatly increase commercial fire clay resources.

Jan 1, 1961

By Kenneth B. Higbie

METALLURGICAL ACTIVITY in 1963 was again dominated by the insatiate demands of research and development conducted in conjunction with the nation's defense and aerospace programs. An increasing effort was noticeable throughout the year, however, to apply to the commercial field many of the processes and techniques that have been developed by government-sponsored research. Particularly effective has been the Industrial Applications Program of the National Aeronautic and Space Agency through which many of the technological advancements made during the course of NASA research and development have been published and released to the public. POWDER TECHNOLOGY Powder metallurgy techniques for fabricating metals, not long ago declared outmoded because of improved casting and shaping methods, have since made an astonishing comeback. Traditionally mechanical pressing of powder shapes has been employed when melting and casting was difficult or impossible, when phase relationships needed to be sidestepped, or when machining costs could be avoided. Hence, it has long been used for producing relatively small special shapes of high-melting metals and alloys. Small iron parts produced with a punch and die have been common for many years, but powder metallurgy techniques are now applicable to a wide range of materials and items. Hard-to-handle materials including refractory metals and their alloys are now rolled, forged, or extruded from billets made by sintering isostatically compacted powders. The major element of the powder metallurgy industry still comprises iron shapes, however, and two-thirds of the annual 100,000 tons of powder metallurgy products are made of iron. The largest single user of powder-forming techniques is the automobile industry which currently consumes 14,000 to 16,000 tons of iron powder per year. A typical 1963 model auto contained more than 100 pressed powder parts (e.g., transmission gears, timing gears, sprockets, ball joint suspensions) totaling 5 to 7 pounds per car. Some of these powders are used in self-lubricating parts of porous copper and copper alloys containing as much as 20 volume-percent lubricating oil. The expanded use of powder techniques, coupled with

Jan 1, 1964

By Thomas P. Mucho, David C. Oyler, Jim Pablic, Dennis R. Dolinar

A room and pillar coal operation in central Pennsylvania was experiencing roof cutters and long running roof falls caused by high horizontal stresses. The roof conditions created hazards for the miners, and caused several production panels to be abandoned prematurely. The mine requested assistance from the National Institute for Occupational Safety and Health (NIOSH) in applying the "advance and relieve" mining to reduce the affects of the horizontal stress during panel development. The "advance and relieve" plan that was developed called for removing a pillar on one side of the panel as it was being advanced, thus creating a cave. The caving then relieved a portion of the horizontal stress across the panel. Because the horizontal stress direction is key to the success of this method, stress mapping as well as mining experience was used to establish the direction of the horizontal stress. Subsequent field measurements provided an estimate of the stress magnitude. Three panels were mined using this technique, and good roof conditions were achieved in all these panels. Instrumentation was used to monitor the stress changes in the roof created by the cave. Stress relief of over 1,000 psi was measured 120 ft from the cave and to depths of 20 ft into the roof. The lateral extent of the stress relief zone across the panels appears to be about 400 to 500 ft. This case history has provided much insight into the practical application of the "advance and relieve" method discussed in this paper.

As mining operations in the United States (US) have become more productive, controlling the dust exposure of mine workers has become more challenging. In response, US mining operations are applying basic controls at elevated levels and are looking to emerging control tech­nologies in an effort to better control airborne respirable dust levels. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) conducts research to develop and/or improve control technologies that reduce the respirable dust exposure of workers in underground coal mines. The goals of this research involve optimizing the use of water sprays and ventilating air, as well as, evaluating emerging control tech­nologies. An overview of dust controls typically utilized in underground US coal mines will be provided. An update on ongoing PRL research efforts that are evaluating new control technologies will also be presented.

Jan 1, 2008

By Dennis R. Dolinar, Jeff Dubbert, Hamid Maleki

The advance-and-relieve method benefits from lateral destressing associated with mining in laminated rocks and a high horizontal stress regime. This stress control method is based on measurements showing that occurrence of rock failure in the roof and floor of an entry (or caving of roof strata in a panel gob) results in redistribution of stresses in adjacent entries. By locating other entries within the shadow zone of the first entry (or gob), improvements in stability can be achieved. Numerical modeling proved useful in studying the basic mechanics of lateral relief while investigating the sensitivity of results to different geologic and mining parameters using controlled experiments. It was shown that failure of rocks near an entry results in redistribution of horizontal stress and shifting of the stress to higher horizons. Measurements from two mines are consistent in showing significant horizontal stress reductions in comparison with the far-field stress regime within the destressed zone. Although the far-field stress regime is very anisotropic, these measurements show near-equal secondary principal horizontal stresses, or perhaps a switch in orientation, as a result of destressing. Stress relief is achieved through lateral movement and relaxation of rocks along weak bedding planes toward adjacent caved zones (or softened zone). Because of cave geometry in the advancing panel, horizontal stress concentrations occur near the cave line both in front of the face and to the sides. The horizontal stress concentration reaches 1.7 times the far-field stress ahead of the face. This stress increase is significant and may cause structural damage in this zone benefiting from additional support. In the next advancing panel located within the shadow zone of the gob, horizontal stresses are significantly reduced in the roof (by 50%). Thus, the stability of future advancing panel can be improved through prudent layout designs and sequencing. The width of the relief zone is significantly influenced by the height of the softened (or cave zone) and rock mass properties.

By L. J. Prosser, Robert Anderson

Advance knowledge of roof conditions can lead to improvement in roof control strategies that will reduce roof falls and ultimately will reduce injuries to mine workers. J.H. Fletcher and Company, in cooperation with West Virginia University, has been developing a system to meet these needs by collecting torque, thrust, and rotation speed data during drilling operations. Recent improvements in analysis algorithms to detect anomalies in the roof structure as well as various display enhancements for real time mapping and evaluation of roof structures have been incorporated into current Fletcher Information Display system. The unit has also been housed in an explosion-proof container to allow use in coal mine applications. Recently, the system has undergone extensive field trials in several limestone mines and one coal mine. During these trials, the National Institute for Occupational Safety and Health assisted Fletcher in verifying the accuracy of the roof mapping capability of the system by comparing the display information to bore hole scoping observations and drill corings. It was concluded from this assessment that the intelligent drilling system can complement scoping and core analysis to provide a more complete picture of roof strata and is capable of seeing features or conditions that are not always obvious in these more traditional methods.

By Peter Swanson, John Rettkowski

As part of a research program to reduce injuries and fatalities in the U.S. mining workforce, NIOSH is investigating the potential use of noncontact vibration measurements to identify hazardous ground fall conditions. In the present study, the effectiveness of remote vibration sources in exciting resonant responses in damaged structures is examined. Initial experiments were performed on a damaged concrete slab in a controlled environment. Vibration response was measured with a laser Doppler vibrometer using both single-point and two-dimensional array recordings. Excitation sources included direct mechanical impacts to remote portions of the slab and a remotely located industrial demolition hammer. Surficial damage was effectively delineated with both sources through visualization of vibration response in spectral bands selected to discriminate wave propagation from large-scale slab resonance effects.

Pillars with width to height ratios of less than 1.0 are frequently created in underground hard rock mines. The strength of slender pillars can be estimated using empirically developed equations. However, the equations can provide variable results when the width-to-height ratios approach 0.5. This paper investigates some of the issues affecting pillar strength at low width-to-height ratios in hard brittle rock. The investigation includes an evaluation of empirical pillar strength data presented in the literature and observations of pillar performance in underground limestone mines in the eastern United States, supplemented by numerical modeling in which failure processes and sensitivity of slender pillars to variations in rock mass properties are evaluated. The results showed that the strength of slender pillars is more variable than that of wider pillars. The numerical model results demonstrated the increasing role of brittle rock failure in slender pillar strength. The absence of confinement in slender pillars can result in a fully brittle failure process, while wider pillars fail in a combined brittle and shearing mode. The onset of spalling in slender pillars occurs at or near the ultimate strength, while this is not the case for wider pillars. Slender pillars are shown to be more sensitive to the presence of discontinuities than wider pillars, which can partly explain the increased variability of slender pillar strength. Two examples are presented, which illustrate failure initiation by brittle spalling and the sensitivity of slender pillars to the presence of discontinuities.

By Gerald T. Homce, James C. Cawley

This paper updates an earlier report by the authors that studied electrical injuries from 1992 to 1998. The previous information is expanded and supplemented with fatal and nonfatal injury rates and trends through 2002. Injury numbers and rates were used to compare and trend electrical injury experience for various groups and categories. This information allowed identification of at-risk groups that could most benefit from effective electrical safety interventions. The data presented in this paper are derived from the U.S. Labor Department’s Bureau of Labor Statistics’ Census of Fatal Occupational Injuries (CFOI), Survey of Occupational Illnesses and Injuries (SOII) and Current Population Survey (CPS). Between 1992 and 2002, 3,378 workers died from on-the-job electrical injuries. Electricity remained the sixth leading cause of injury-related occupational death. From 1999 through 2002, 4.7% of all occupational deaths were caused by electricity, down from 5.2% in the 1992 to 1998 time period. The cause of death was listed as electrocution in 99.1% of fatal cases. Contact with overhead power lines was involved in 42% of all on-the-job electrical deaths. The construction industry accounted for 47% of all electrical deaths between 1992 and 2002, but showed overall improvement from 1995 through 2002 by reducing its electrical fatality rate from 2.2 to 1.5 per 100,000 workers. An additional 46,598 workers were nonfatally injured by electricity. Contact with electric current of machine, tool, appliance, or light fixture and contact with wiring, transformers, or other electrical components accounted for 36% and 34% of nonfatal electrical injuries, respectively. Contact with underground, buried power lines was involved with 1% of fatal injuries and 2% of nonfatal injuries. NIOSH research aimed at evaluating commercially available overhead power line proximity warning alarms is described. This research is expected to be the initial step for eventual development of a performance standard for such systems.

By L. E. Cardwell

This Bureau of Mines publication contains routine analyses and related source data for 495 natural gas samples from 21 States and three foreign countries. Of this total, 376 samples were collected during calendar year 1968. The remaining 119 analyses are of samples collected during previous years, but releases granting permission to publish the results Here not received until 1968. All samples were collected as a part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917 and in late 1965 was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus which are described in Bureau of Mines Bulletins 4863 and 576.4 Ten previous publications have presented results of 8,165 gas analyses made by the Bureau of Hines Helium Activity prior to 1968. The first three, Bulletins 486, 576,6 and 617,7 contain analyses and related source data on

Jan 1, 1970

By Charlie Wyche

In 1980, gold, silver, and pit and quarry construction materials were the principal minerals produced in the Dominion of Fiji. The combined value of these minerals totaled some $7.2 million,2 over 85% of all mineral production, Production of cement, sand and gravel, and quarry products continued to increase, but gold and silver production from Fiji's only operating mine declined slightly from the previous year's level. Mineral exploration has been carried out by U.S., Australian, British, Canadian, West German, and South African companies since the early 1960's, and a high level of activity was maintained throughout 1980. At the end of 1980, some 40 mineral prospecting licenses covering over 4,300 square kilometers were in force, and 19 applications were under consideration by the Mineral Resources Department. Total expenditures by mining companies on land base projects exceeded $6 million in 1980.

Jan 1, 1982

By William R. Vogel

The Bureau of Mines Minerals Information organization collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Minerals Information activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral- material production or consumption.

Jan 1, 1988