Search Documents

By E. A. Loria

The Bureau of Mines analyzed the effects of oxygen, nitrogen, and carbon on the tensile properties of electrorefined vanadium in terms of the Petch equation. The effects of the different impurities and grain sizes on the yield and flow stress between 2730 and 770 K were studied. For specimens of like composition, the values of the Petch parameters 01 and ky obtained by two different methods, extrapolation and grain size, were nearly the same. For high-purity electrorefined vanadium, the 01 value at 2730 K was 10,300 psi (5,150 psi shear). The 01 values for this metal at 1950 and 2730 K were lower by factors of 3 to 4 than for three less pure samples of commercial vanadium metal of equivalent grain size. Nitrogen was more effective than oxygen in increasing 01' the increase being about twice as much for the same impurity level. Carbon produced a slight increase in 01 up to 0.024 percent and then a gradual decrease in 01 to 0.11 percent, the maximum carbon content studied. The corresponding ky values followed the same trend in regard to oxygen and nitrogen additions, whereas the addition of carbon produced no variations at either temperature. Dislocations in vanadium are anchored by carbon, oxygen, and nitrogen with increasing firmness in that order. The high purity of electrorefined vanadium was confirmed by low yield stress and high ductility throughout the low temperature range. The metal also exhibited profuse twinning with high ductility at 1230 and 770 K. The effective surface energy for fracture, y, was found to lie between 3.3 and 3.6 x 1()4 erg cm-2?

Jan 1, 1966

By L. W. Brandt

The Bureau of Mines, as part of its mission to effect pollution abatement, conducted research to study various means of dewatering Florida phosphatic clay wastes and reclaiming mined lands. The work was done in cooperation with 10 Florida phosphate companies. During this work, a novel technique to effectively dewater phosphatic clay wastes was developed. The solids contained in the clay waste slurry are slowly compressed by moving wire mesh screens through the system. In a typical application, the screens were moved downward, compressing solids ahead of the screens. The rate of movement of the screens is an important variable in the process. It is believed that the moving screens distort the gel structure of the phosphatic clay system and cause the release of water. Samples of 18 clay wastes, including a high-grade attapulgite from beneficiation plants of the Florida phosphate field, were studied using the method. Typical samples were concentrated from initial solids of 4.7 and 11.9 percent to 16.8 and 25.2 percent, respectively, in 3-1/2 days. The high-grade attapulgite sample was dewatered from 2.7 percent solids to 13 percent solids in the same period.

Jan 1, 1980

By Hanns J. Billmayer

Optimized Operator Compartment layouts based on previous Bureau of Mines activities in standardization and optimization of controls were designed and installed in three operating vehicles. Two National Mine Service 48A-36 TorKars were modified in production prior to delivery to the Quarto Mining Company. An Elkhorn AR-4 scoop owned by Adanac Coal Company was modified in a local rebuild shop. The modified vehicles were then evaluated underground under normal production conditions for a 60 day period. Vehicle operators and management appear well satisfied with the compartment modifications.

Jan 1, 1976

By Andrew M. Leszcykowski

In 1984, personnel from the U.S. Bureau of Mines examined 41,550 acres of the North Fork Owyhee River Wilderness Study Area for mineral resources. This study area, in southwestern Idaho, is underlain by tuffs and basalt of Tertiary age. There are no known mines, claims, or prospects in or near the area. The northeast and southwest corners of the area are covered by oil and gas leases or lease applications, but no known exploration has been conducted. On Nickel Creek and Pleasant Valley Tables, in the southern part of the area, thin flows of vesicular, moss-covered basalt occur that are suitable for use as decorative building stone. The stone available for exploitation crops out over several square miles. However, more suitable material, outside the study area, is closer to potential markets.

Jan 1, 1986

As part of the United States Department of the Interior, Bureau of Mines Health and Safety Research Program, Walter C. McCrone Associates, Incorporated has examined 71 samples of airborne mine dusts using the techniques of x-ray diffraction, electron microprobe analysis and light microscopy. This report details the procedures which were used in this work and documents the results which were obtained.

Jan 1, 2011

By N. S. Dalal, X. Shi

"SUMMARYElectron spin resonance (ESR) measurements provide direct evidence for the involvement of the glutathionyl radical, as well as an isolable Cr(V)-glutathione intermediate in the Cr(VI) glutathione redox reactions. These results indicate a new mechanism for the reduction of Cr(VI) by glutathione in relationship to cellular environment and suggest that synergistic reactions of Cr(V) and GS· might be responsible for the (unexpected) increase in the Cr(VI)-induced DNA-strand breaks at high glutathione levels.INTRODUCTIONWhile the reduction of Cr(VI) by glutathione (GSH) is thought to be a critical' step in the pathogenesis of the Cr(VI)-exposure related carcinogenesis1- 4, the exact reduction mechanism is not yet understood. The following reaction steps have been suggested :(A) Initial step:Cr04 2- + GSH - GSCrOa - (1)(B) At high GSH levels:GSCroa- + GSH - Cr( IV) + GSSG (2)(C) At low GSH levels: GSC rO a - - Cr ( V ) + GS ·(3)Thus far, however, in these reactions, the GS· radical has eluded spectroscopic detection, while the evidence for the Cr(V) formation has been reported positives as well as negative2·. Her~ we present spin-trap ESR evidence for the formation of the GS· radical, and a definitive ESR detection of an isolable cr(V)-GSH intermediate in Cr(VI)-GSH reactions.MATERIALS. AND METHODSESR spectra were obtained at X-band (-9.7 GHz) using a Bruker ER200D ESR spectrometer. The magnetic field was calibrated with a self-tracking NMR Gaussmeter (Bruker, Model ER035M) and the microwave frequency was measured with a Hewlett-Packard (Model 5340A) frequency counter. The spin probes, a-(4-pyridyl-1-oxide) -N -tert-butylnitrone (4-POBN) and 5,5-dimethyl~1-pyrroline-1-ox1de (DMPO) were purchased from Aldrich, K2Cr201 from Fisher and used without further purification. All experiments were done at room temperature."

Jan 1, 1989

By Walter D. Holland

This study was undertaken to determine miners' breathing zone concentrations of diesel exhaust components, to investigate any relationships between these concentrations and vehicle type, the presence of emission controls, vehicle usage, and ventilation conditions, and to make recommendations for monitoring and ventilation requirements. Twenty-four mines including two con l mines were surveyed. Sampling was done for CON, NON, SOx, PNA, aldehydes, and particulates. hi most mines, concentrations of at least one contaminant exceeded one half the standard or TLV. The concentrations of gases arc probably sufficiently reduced by a minimum air velocity of 50 fpm. A sufficient reduction of particulate concentrations may require as high as 400 fpm air velocity. Vehicle age, type, or usage appear to have little or no effect on contaminant concentrations. PNA levels were below detection limits in all but a very few samples. Minimum requirements for routine monitoring should include formaldehyde, COx, NO2. It is further recommended that better definition of the minimum ventilation requirement be obtained.

Jan 1, 1978

By William L. Rice

This Bureau of Mines Open Pile Report on cobalt is one of a series of minerals availability commodity deposit abstracts. Nonconfidential information from the Minerals Availability Program data base covering domestic and foreign cobalt properties and deposits has been abstracted for use in his report. Abstracts include applicable data on location, published reserves and resources, geology, mine and beneficiation systems, and operation information.

Jan 1, 2011

By Albert Ketler

[Early Bureau of Mines research had produced a fluorescent mine illumination system which was approved by MESA under Schedule 29A for use as portable equipment Intense industry preference for machine-mounted hardware required a MESA 2G approved system. The modifications required to upgrade the portable system arc herein described.]

Jan 1, 1976

By A. D. Hahn

This report describes and gives the results of an examination by the Federal Bureau of Mines of ilmenite-bearing placer sand deposits in the 24-mile long valley of Otter Creek, Kiowa and Tillman Counties, Okla. Drilling and sampling was completed in three periods between October 1956 and September 1957. Mineralogic studies and mineral-dressing tests on recovery of ilmenite and other heavy minerals from composited samples of the sands were made in Bureau of Mines laboratories at Rolla, Mo., in 1957 and early 1958. Otter Creek rises in and drains the southwestern extremity of the Wichita Mountains, which are represented locally by knolls and ridges of gabbro and granite surrounded by plains floored with flat-lying Permian red beds. The valley fill consists of a basal sand-clay component, derived from weathering of the igneous rocks, and an overlying silt-clay alluvium. Ilmenite is present in significant quantity and recoverable grain size only in the basal sand-clay.

Jan 1, 1960

By Thomas V. Falkie, R. Venkataramani

Hand portable truck axle scales were purchased from the Martin¬Decker Company, Santa Ana, California, for weighing the rubber-tired mine shuttle cars. The scales consisted of two hydraulic load-pads, measuring 4" thick, and 21" long by 13" wide at the pad surface and one totallizer-dial indicator unit. The development of a technique to install the scales effectively for shuttle car-weighing followed an evolutionary process. The setup which finally proved to be effective entailed countersinking and level¬ling the load pads in the floor on the shuttle car trackway such that the tops of the pads were three inches below the floor level. A plat¬form consisting of two braced side-by-side 3" x 8" lumber planks was made. The platform was placed across the load pads with six inches of overlap on each side to provide room for imperfect tracking of the shuttle car. Additionally, 3" x 8" lumber planks were imbedded across the runway immediately behind and ahead of the platform. These auxili¬ary planks were firmly braced into the floor by vertical posts or jacks set against the roof; the planks constituted a stable approach platform to enable the shuttle car to roll unimpeded onto the scale platform in either direction of travel. Figure 22 shows this arrangement in detail. The setup of the scales was done during non-production hours prior to the first working shift of the week. This task took seven to twelve hours with two men. During the actual weighing experiment, the following limitations were realized. 1. Delays will be introduced into the cycle of operations because the shuttle cars must be stopped and positioned on the platform. However, these delays can be held to a minimum, time wise, as the

Jan 1, 1972

By John P. Hansen

Batches of red or brown iron ore concentrates, weighing 100 or 200 grams, were reduced with gaseous reductants in a laboratory-sized fluidized-bed reactor. Using a loss of weight technique, the rates of reduction were measured and the effects of temperature, gas consumption, and gas flow rates were determined. Below about 725° C the rate of reduction was controlled by the chemical reaction at the reduction interface having an activation energy of about 10 kcal/g mole. Above about 725° C the rate of reduction appeared to be controlled by the flow of the gaseous reductant and therefore to be directly proportional to the flow rate. Above 725° C, hydrogen reduced the iron ore much faster than carbon monoxide. In gas mixtures, carbon monoxide or nitrogen reduced the hydrogen partial pressure and lowered the reaction rate proportionally. When present in large concentrations, carbon monoxide had a serious inhibiting effect on the reduction rate, probably owing to carburization and sintering of the reduced iron.

Jan 1, 1970

By W. M. McKewan

This U.S. Bureau of Mines report discusses wire ropes used for hoisting in U.S. mines. The in-formation presented was extracted from a large body of data compiled by the U.S. Mine Safety and Health Administration (MSHA) using a data base management system (DMS). Further, these extracted data were then manipulated to provide tables of data that show the types and amount of wire rope used for hoisting. This report describes the different types of wire ropes and how a DMS can be used to manipulate MSHA's wire rope inventory data. The data indicate that more 1-1/4-in-diam ropes, 6x27 construction ropes, and right lang lay ropes are used in U.S. mines than ropes of any other diameter, construction, or lay type.

Jan 1, 1991

By John E. Husted

Quantities of kaolin in Georgia in-contiguous or single bodies had been established by previous work to be sufficient for an alumina industry. The need for characterization of this kaolin to determine its suitability as an ore of aluminum resulted in the studies described herein. It was determined in an area roughly 7 x 27 miles, known as the Wrens district that approximately 5.9 billion short tons of kaolin averaging 35.55 percent A1203 exist in an essentially continuous clay body. The Macon-Sandersville district consists of discontinuous kaolin bodies averaging 35.28 percent A1203 with an average thickness of 28 feet. Tonnages for this district are not available. One hundred and twenty core samples of kaolin were analyzed for K20, CaO, MgO, Al203, T102, Cr203, Fe203, Si02, P205, and F. The P205 and F were analyzed by wet chemistry methods and the others by electron microprobe. Seventy-nine of the samples were from the Wrens district forty from the Sandersville-Macon district and one from the Andersonville district. Emission spectroscopic analyses were also made to qualitatively determine all elements present for each core. X-ray diffraction studies were made of each core to determine mineral species present. Scanning and transmission electron microscope pictures also are given for each I' core sample. Elevations, overburden thickness, and kaolin thickness are given for each core site as well as map locations. Isopachs for over-burden and kaolin thickness are given for the Wrens district.

Jan 1, 1983

By Michael J. Bertoldi

The purpose of this Bureau of Mines report is to describe the methods and establish the basic economics for dragline, shovel-truck, and scraper mining systems. An overall view of the techniques of preliminary design and the cost involved is presented. Considerations of equipment selection, emphasizing short-range evaluation of required equipment, and a long-range evaluation are considered at a constant production rate over the life of a hypothetical mine. Separate cost analyses for each system were based on 1977 equipment prices, prevailing wage rates, and associated mining costs. Specific engineering and cost breakdown for such items as access roads, transmission line installation, rail spurs, etc., are beyond the scope of this report.

Jan 1, 1977

By C. B. Davison

One goal of the Bureau of Mines is to conserve the Nation's mineral resources by developing improved performance materials. Consistent with this goal, the Bureau conducted studies on the formation of undesirable cristobalite in seven different fire clays used as refractories. The studies employed scanning electron micrography, chemical and X-ray analyses, and pyrometric cone equivalent determinations to examine the sample clays and determine the effect of thermal history and stablilizing additives on the amount of cristobalite in various calcines. This research has indicated that as fire clay calcining temperatures increased from 1390° to 1,490° C there was a gradual decrease in the percent of cristobalite present in the calcines and a progressive development of mullite crystallization. No cristobalite was found in fire clays calcined above 1,550° C, but cristobalite reappeared when the calcines were reheated to temperatures between 1,400° and 1,500° C. The research also revealed that additions of lithium fluoride (LiF) prevented formation of cristobalite in fire clay calcines.

Jan 1, 1979

By Ivette E. Torres

The final 26 tables of this chapter, tables 24-49, extend and expand the statistical series on production that was started in the 1963 edition of the Area Reports: International volume of the Minerals Yearbook and that was subsequently updated and expanded in the 1965 and 1967-90 editions. Mainly because of the separation of the countries that formed the U.S.S.R., the column that provided a 5-year average, was deleted. The listing order of major producers, however, continued to be, as in past years, in descending order of rank in the year of review, 1992. This group of tables now includes each of the top 19 crude minerals in 1983 in terms of value of their output plus 3 others of lesser rank. These 22 crude mineral commodities accounted for more than 98 % of the estimated value of world crude mineral production in 1983. Coal production, included in the 1983 value of production table as two separated entries, is combined in one table in this chapter. World output of five key downstream products-aluminum, steel, cement, nitrogen in ammonia, and refined oil-is included because of their significance as products.

Jan 1, 1994

By R. D. Leitch, W. P. Yant, A. C. Fieldner, R. R. Sayers, S. J. Pearce

"The detection of leakage is a recognized problem in the safe and economic distribution and use of natural gas. Natural gas is practically odorless and therefore lacks he property of indicating significant leakage by the sense of smell, the means most widely used by gas employees and consumers for detecting leaks of the more odorous types of fuel eases. In view of the recognized value of the odor of gas for indicating leakage at the time of occurrence the Bureau of Mines has studied' the possibility of adding small amounts highly odorous substances to types of fuel gas (such as blue water gas and natural gas) that lack warning properties. These studies revealed that the mercaptans were promising substances to accomplish this purpose, not only for odorizing fuel gases but for other purposes° where it was desired to give warning through the sense of smell.Since completing the studies mentioned, the Bureau of Mines jointly with the American Gas Association has conducted further investigations dealing with the use of warning agents for fuel gases. The results of this work will be published later.The Bureau of Mines had been desirous of observing the practical use of ethyl mercaptan for detecting leakage of natural gas, particularly to determine whether the odor would permeate the ground and give indication of lea's in underground pipes. Opportunity for making these observations was recently given by E. A. Munyan, manager, gas department, Union Gas t Electric Co., who requested the bureau's cooperation in making leakage surveys of the company's distributing systems at Franklin and Middletown, Ohio."

Jun 1, 1930

A computer program for the static load analysis of linear elastic structures is presented. It is the product of a two-year project for the development of a efficient program for the analysis of mine-type structures. The report is divided into two parts. The first part explains the general method of analysis, the computer program organization and the most significant numerical techniques used. The second part is a user manual for the computer program. The FORTRAN IV computer program deck and example problems were transmitted separately to the sponsor. Request for a copy of the program should be directed to the Bureau of Mines, Denver Mining Research Center.

Jan 1, 1972

By James M. Spear

Sample results suggest the only mineral resources in the study areas are placer gold deposits along the South Fork Kern River in the Woodpecker RARE II unit (fig. 1). These deposits, in Rockhouse Basin, total 4.5 Figure 1.--NEAR HERE. million cu yds (3.4 million cu m) of indicated subeconomic gold resources in four deposits of "older" gravel. Gold value in samples averages $0.36 per cu yd ($0.47 par cu m) and is as much as $4.44 per cu yd 1/. Cost of mining the gravel and recovering the placer gold is estimated to be more than $2 per cu yd ($2.62 per cu m) for a deposit of this size and type. Additional inferred subeconomic placer gold resources with similar grade probably occur in four other deposits of "older" gravel on which no mining claims were located. Placer gold occurrences on upper Trout Creek contain gold worth as much as $4.50 per cu yd ($5.88 per cu m) 1/. Average grade is much lower, and only about 1,000 cu yds remain (760 cu m). These occurrences do not constitute a resource, but may attract hobbyists not dependent upon making a profit.

Jan 1, 1982