Search Documents

By J. S. Hansen

To improve mine safety, the Bureau of Mines has conducted a search for better materials and systems to anchor roof bolts. This report describes a study on the ability of a gypsum-based anchoring medium to withstand short- and long-term loads. Results showed that 2-ft-long bolts anchored with gypsum that was injected as plaster slurry at a 0.370 water-cement ratio and cured for 10 min sustained pull test loads equal to the ultimate strength of the bolt steel (about 37,000 lb). For comparison, the minimum required capacity is 17,600 lb. Long-term loads of 15,500 lb were sustained with estimated 10-yr movement of less than 1/2 in. Two-foot-long bolts anchored with gypsum installed in a cartridge in which the water was contained in tiny capsules sustained a pull test load of about 30,300 lb at a 0.319 water-cement ratio and 10-min cure time. At a 0.288 water-cement ratio, load capacity was about 37,000 lb. The lower load capacities of cartridge-installed bolts resulted primarily from the remnants of the water-wax capsules. Above 10,000 lb, creep movement of cartridge-grouted bolts appears excessive, but longer bolts may be capable of resisting creep better.

Jan 1, 1985

By Joseph W. Horne

This report presents the results of an investigation by the U. S. Bureau of Mines in cooperation with the State of Colorado, on the yields and properties of oils produced from oil shale, lignite and subbituminous coal using the standard assay method developed by the Bureau for oil-shale testing,. The purpose of this work, which is part of the general study of oil shales being conducted by the Bureau of Mines and cooperating agencies, was to obtain information on the amount and character of the yield of crude oil or tar from different typical oil shales, the yield of light oil or naptha that might be suitable for use in motor fuels, and other products of shale oil. As the west has large resources both of oil shale and low-grade non-coking coals, it is of interest to know the relative yields of tars, light oils, and combustible gases that can be produced from these coals when retorted under conditions similar to those suited for oil-shale retorting. Source of Samples The coal samples were obtained from deposits on or adjacent to the public lands in the States of the Rocky Mountain region. Many of the mines sampled are operating under Government leases or permits. The number of coal samples secured from the various states are: Colorado, 6; Montana, 9; north Dakota, 6; New Mexico. 1; South Dakota, 1; Wyoming, 9. Of these samples, 14 were lignite coal, 16 subbituminous coal, and a bituminous coal. The standard channel method of the Bureau of Mines was used for sampling. Coal samples received at the Boulder Office weighed about twelve pounds each, and duplicate samples were sent to the Pittsburgh Station for proximate and ultimate analyses. The origin of the samples and description of the deposits are given in Table 1.

Jan 1, 1927

By K. K. Kelley

This work is a continuation of a program of study of the measurement and correlation of fundamental thermodynamic data inaugurated several years ago by the United States Bureau of Mines. Previous bulletins in this series were concerned with (1) The Entropies of Inorganic Substances (66),3 (2) High-Temperature Specific-Heat Equations for Inorganic Substances (67), (3) The Free Energies of Vaporization and Vapor Pressures of Inorganic Substances (68), (4) Metal Carbonates-Correlations and Applications of Thermodynamic Properties (71), (5) Heats of Fusion of Inorganic Substances (69), and (6) A Revision of the Entropies of Inorganic Substances-1935 (70). The present bulletin has as its primary purpose the correlation of the thermodynamic properties of elementary sulphur and its inorganic compounds and the presentation, after careful consideration of all available information, of a self-consistent system of thermodynamic relationships for these substances. It is believed that such a set of relationships, concerning substances of such great metallurgical importance as sulphur, sulphur oxides, hydrogen sulphide, metal sulphides, and metal sulphates, is of considerable value in indicating directions of possibly profitable experimental work and in clarifying subjects of technical interest upon which direct experimental information is difficult and expensive to obtain. It cannot be doubted that many problems of technical importance that at the outset appear almost hopelessly complex or obscure either may be solved, if enough information is available, or the specific lacking information clearly indicated by the adoption of the thermodynamic viewpoint. This has been demonstrated many times in the work of the Metallurgical Division, Pacific Experiment Station, Berkeley, Calif. Even when only crude basic information is available, a semiquantitative picture often may be developed by thermodynamic means in which general trends and approximate limits of a proposed process or modification of practice may be clearly portrayed and thus used as guides in further considerations and experimentation.

Jan 1, 1937

By Shail J. Butani

In 1986 the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 years; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSHA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey's results to characterize the U.S. stone mining workforce from March through September 1986. Similar reports have been published for the metallic, sand and gravel, and nonmetallic mining industries, as well as for the entire metal and nonmetal mining (includes metallic, stone, sand and gravel, and nonmetallic industries) sector and the coal mining sector.

Jan 1, 1988

By Donald E. Redmon

This Bureau of Mines report examines the injury experience in the quarrying industry For the years 1966-67. Twenty-eight tables for each year are presented in which disabling work injuries are summarized by department, source of injury, extent or disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973

This publication summarizes the in-house and contract research and development projects programed for fiscal pear 1980 by the Bureau of Mines under its Minerals Environmental Research activity. The document provides a mechanism for interested parties, including potential contractors, to gain insight into ongoing and projected work of the Bureau's environmental research efforts. Research to identify and correct environmental problems associated with mining and metallurgical operations has long been an integral part of the Bureau's mission. Through the years, efforts of various Bureau programs have yielded valuable information on the origin and control of many of these problems. With the reorganization of the Bureau of Mines in 1979, the Minerals Environmental Technology program was structured to consolidate these efforts into a single program that will systematically investigate al aspects of mining- and processing-related environmental pollution and damage-from initial discovery of the mineral resource to ultimate return of the land to productive use. In fiscal year 1980, the Bureau received an appropriation of about $21 million to conduct research and development work on these problems.

Jan 1, 1980

The Technical Study Panel on the Utilization of Belt Air and the Composition and Fire Retardant Properties of Belt Materials in Underground Coal Mining (hereafter referred to as the Panel or the TSP) was established by Section 11 of the Mine Improvement and New Emergency Response Act of 2006 (MINER Act). The Panel was charged with providing “independent scientific and engineering review and recommendations with respect to the utilization of belt air and the composition and fire retardant properties of belt materials in underground coal mining.” The TSP was impaneled by the Honorable Elaine L. Chao and commenced its work on January 9, 2007. At this first meeting, Mr. Richard E. Stickler, Assistant Secretary of Labor for Mine Safety and Health, asked the Panel to report on many issues including how recent technological advances could be applied to atmospheric monitoring systems, point-type heat sensors, current state of fire-resistant vs. fireproof belt materials, and belt fire suppression systems to improve miner safety. In addition, Mr. Stickler asked the Panel to review belt air velocity limitations. The Panel members attended 12 days of public meetings over a nine-month period. Three of the public meetings were scheduled for the Panel to hear from technical experts and those persons or organizations interested in providing input. The meetings were held in Coraopolis, Pennsylvania with emphasis on belt fires, belt maintenance, belt flammability and toxicity, ventilation, and escape issues; in Salt Lake City with emphasis on ground control and convergence issues; and in Birmingham with emphasis on fire detection, sensors and atmospheric monitoring systems. National Institute for Occupational Safety and Health (NIOSH) researchers, Mine Safety and Health Administration (MSHA) personnel, representatives of the major belt conveyor manufacturers and a representative of the National Mining Association provided discussions at the Coraopolis meeting. In Salt Lake City, Utah, MSHA district managers and ventilation specialists, a member of the Aracoma Mine No. 1 investigation team, a representative of the Bureau of Land Management, and industry and consulting representatives of the Utah Mining Association and the Colorado Mining Association made presentations. In Birmingham, Alabama, atmospheric monitoring system representatives, NIOSH researchers, representatives of coal mining companies, and UMWA workers from two Alabama mining companies made presentations. In addition, a staff member of The Center for Regulatory Effectiveness also presented comments to the Panel. In conjunction with the meetings in Salt Lake City and Birmingham, three-member subcommittees of the Technical Study Panel made field visits to the Skyline Mine, the Aberdeen Mine, and the Jim Walter Resources Mine No. 4. The mine visits were scheduled to see first-hand the mining conditions under which belt air was being utilized as an additional source of intake air for working sections.

By J. R. Thoenen

[For several years the Bureau of Mines has conducted tests on ground vibration emanating from quarry blasting in an effort to determine Fin index of destruction for different types of structures. Results of these studies have been published in four Bureau of Mines Reports of Investigations as well as in several articles in the trade and technical press.5/ The first paper (3)6/ discussed the subject in general and gave results s of a few blasting records. Some tentative theories also were advanced. The second paper (4) discussed results s of records made from blasting in a number of quarries.]

Jan 1, 1940

By J. R. Thoenen

[For several years the Bureau of Mines conducted tests on ground vibration t emanating from quarry blasting in an effort to determine an index of destruction for different types of structures. Results of these studies have been published in four Bureau of Mines Reports of Invitations as well as in several articles in the trade and technical press.5/ The first paper (3)6/ discussed the subject in general and gave results s of a few blasting records. Some tentative theories also were advanced. The second paper (4) discussed results s of records made from blasting in a number of quarries.]

Jan 1, 1940

By Thomas C. Ruhe

The Pittsburgh Research Laboratory of NIOSH conducted research to determine the safe operating conditions for using recycled (used) lubricating oil from mining equipment as a partial replacement for diesel fuel to make ANFO-type blasting agents. The use of recycled oil (RO) conserves energy, reduces oil imports, and reduces mining costs. Since RO has a variable composition, there was concern that the additives/impurities it contains may cause ANFO made with RO to be unstable (as compared to regular ANFO) at high summer ambient storage temperatures. Reactivity of RO with zinc was also a concern. Thermal stability tests were conducted to help quantify and resolve these issues. ANFO mixtures (0.66 lb/300 g) were put into sample containers made of steel, stainless steel, and galvanized (zinc coated) steel pipe fittings, which were heated in isothermal ovens. The experimental parameters were temperature settings of 140° F (60° C) and 176° F (80° C), four sample container (pipe fitting) metal combinations, and nominal heating periods of one and three days. The ANFO samples contained 6% each of the following twelve different oils/oil mixtures: No. 1 was diesel fuel, Nos. 2 thru 6 were five candidate oils (2 thru 5 were used oils and 6 was a new synthetic oil), No. 7 was 5% diesel fuel + 1 % graphite, and Nos. 8 thru 12 were 3% diesel fuel + 3% each of the five candidate oils. All samples showed no reactivity when heated at 140° F (60°C). All samples (except No. 7) reacted at 176° F (80° C) in a steel pipe with galvanized caps as follows: No. I reacted most, Nos. 8-12 reacted moderately, and Nos. 2-6 reacted least. All ANFO samples were tested and found not to be cap sensitive.

By Harry W. Campbell

A mineral survey conducted by the U.S. Bureau of Mines in 1983 identified no mineral resources in the Beaver Meadows, Blind Horse Creek, Chute Mountain, Deep Creek/Battle Creek, and North Fork of Sun River Wilderness Study Areas (WSA's). A prospect east of the Beaver Meadows WSA has low potential for lead resources. Sand, gravel, and limestone occurrences are numerous in the WSA's; however, similar or better quality materials outside the areas are abundant and more accessible to potential markets. Impure coal and titaniferous-magnetite occurrences are near the WSA's, but are not known to occur within these areas. In 1983, there were 7,025 acres leased for oil and gas within the five WSA's; no current mining claims were in or near any of the WSA's. Evidence of mining activity was found at only one prospect in the WSA's. It is inside the Deep Creek/Battle Creek WSA; no resources or resource potential were identified at this prospect.

Jan 1, 1984

To predict the spontaneous combustion potential of bituminous coals using a simple expression based on an easily acquired coal property. Background Approximately 20% of underground coal mine fires in the United States since 1978 have been attributed to spontaneous combustion. Spontaneous combustion fires in underground mines are most likely to occur in gob area; and are difficult to detect and to extinguish by direct fire fighting methods. Often, sections of the mine or the entire mine must be sealed for long periods, at a great economic loss to the mine operator, mine employees, and the surrounding community. It is conservatively estimated that the cost of scaling a large mine is about $50 million.

Jan 1, 1989

By V. R. Spironello

The Bureau of Mines is involved in research directed toward the conserva¬tion of important raw materials and the utilization of solid waste. Two of the objectives are to conserve high-quality coking coals used for foundry coke and to utilize waste materials of marginal quality but of high calorific value. These objectives are consistent with Bureau goals. Pilot plant cupola trials were made to evaluate the adequacy of various alternative fuels, and to determine to what extent they could replace the foundry coke in cupola charges. Information was obtained on furnace performance, metal and slag chemistry, environmental questions, and the properties of castings. It was shown that anthracite or bituminous coals can partially replace charge coke up to the 40 pet level. Briquetted materials prepared from fuel fines, and waste prod¬ucts or byproducts of high calorific value, all tend to break down on heating in a cupola so that their use must be restricted to below 20 pet replacement. In cases where pitch-bonded coal fines or petroleum coke were used, carbon pickup by the iron was inadequate for gray iron specifications. Although emphasis during this work was placed on basic slag practice, some acid practice results are included.

Jan 1, 1980

By R. E. Simpson

Beginning in 1972, fully grouted resin bolts were used in underground mines. An estimated 20 million resin bolts will be installed in 1980 owing to their apparent support improvement in most roof-bolt applications. Inorganic cements were tested to replace the resin at a lower cost while retaining the advantages of a grouted bolt. Although other inorganic materials were considered, all but portland and gypsum cements were rejected for reasons of availability, performance, or cost. Portland and gypsum-type cements were tested by the Bureau of Mines to select a fast-hardening, low-cost material that would anchor a roof bolt adequately to meet safety standards. An alpha-gypsum cement, accelerated with potassium sulfate, was selected as the best material because it had adequate pull strength at a desired set time of less than 5 minutes and was readily available.

Jan 1, 1980

By Chas. F. Jackson

The annual reports of the supervising engineers of the seven sections comprising the Mining Division are assembled in the following pages and constitute the annual report of the division. In planning activities, the aim has been to adapt the work to changing conditions and needs of the mining industries and to avoid becoming bound to any particular type of investigation when others are found to be of more pressing interest.

Jan 1, 1939

By A. E. Raddatz

In an attempt to develop technology to use domestic resources in place of imported bauxita, the Bureau of Mines investigated sulfurous acid leaching to extract alumina from kaolin. The process consists of leaching the calcined kaolin with a 30 wt-pct S02 solution at 60° C and 160 psig for 17 hours, fil¬tering the leach slurry, precipitating monobasic aluminum sulfite from the filtrate at 110° C and 60 psig, a& decomposing the sulfite in the spent liq¬uor at 150° C and 55 psig to produce crude alumina. Purification of the crude alumina was accomplished using a modified Bayer process. Results from closed-circuit tests employing the sulfurous acid process showed that overall extraction of alumina from kaolin was 67 pct. Production of 1 ton of alumina would require 3.6 tons of calcined kaolin, 0.7 ton of sul¬fur dioxide, and 8.4 tons of water. After purification by a modified Bayer process, the alumina product contained the following; impurities, expressed in weight-percent: Fa203, 0.009; S, 3.6; Si02, 0.07; Ti02, 0.002; K20, 0.017; and P205, 0.03.

Jan 1, 1981

By Thornton L. Neathery

Geologic investigation of a mineralized zone in eastern Alabama indicates that large quantities of talc and soapstone are scattered over a wide area close to the surface. Laboratory experiments show that this material may be upgraded to a high-quality talc. A market survey indicates that the talc deposits may be of current and long-range interest. The anthophyllite asbestos which is associated with the talc does not appear to occur in sufficient quantities to be considered as a primary commercial source.

Jan 1, 1967

The annual reports of the supervising engineers of the seven sections comprising the Mining Division are assembled in the following pages and constitute the annual report of the division. In planning activities, the aim has been to adapt the work to changing conditions and needs of the mining industries and to avoid becoming bound to any particular type of investigation when others are found to be of more pressing interest.

Jan 1, 1939

By James M. Link

A program was initiated tinder sponsorship of the U. S. Bureau of Mines to investigate pipeline behavior of raw and spent oil shale slurries. Slurries were recirculated in pipeline loops with 150-mm and 200-mm diameter horizontal test sections and a 150 -mm diameter vertical test section. Slurry concentrations from 10 to 60 weight percent were investigated. Critical and deposition velocities were observed. Head losses were measured at various velocities. Rheology measurements were made on representative homogeneous samples from the pipeline. From these data, pipeline energy requirements were predicted by computer and compared to pipeline data. Computer programs were also used to analyze pipeline data for two flow models: 1. Heterogeneous flow regime for coarse, settling slurries 2. Homogeneous flow regime for nonsettling suspensions The economics of slurry transport of raw and spent shale were examined. Cost estimates encompassed a range of pipe diameters to transport a wide range of throughputs of both raw and spent shale. Similar estimates were made for conveyor belt systems to provide a valid cost comparison. Economic comparisons are valid in a general sense, but a specific study must be made to determine the cost advantages of hydraulic transport for a given mine.

Jan 1, 1977

By Donald R. Corson

The effects of adding varying amounts of type I portland cement to hydraulic backfill are described. Six different fill materials, each with three cement contents, were tested to determine which fill properties have the most significant effect on cemented strength. Two strength prediction equations, based on the physical and mineralogical properties of the fills, were formulated, and these accounted for 96 and 99 percent of the variability of the data. Results of both unconfined compression and triaxial tests of cemented fills are given, and the effects of moist curing and fill densification on the 7-day strength are discussed. Permeability test data are given, and the decreased permeability due to cement content and curing time is shown graphically. A discussion of the limited evaluation of other potential stabilization additives (expansive cement, fly ash, sodium silicate, gypsum, and asphalt) is included in an appendix.

Jan 1, 1970