Search Documents

By Lynn Long

We have seen many new developments in the explosive and blasting accessory category, but one of the most useful items is the blast control plug. Blast control plugs are cone shaped units that are placed in the stemming just above the explosive load. They are placed about 8 to 12 inches up into the stemming material.

Jan 1, 1996

By Jean M. Bouvet, Pierre M. Vuillaume

There is not just one ANFO: ANFO explosive behaviour depends significantly on the blasting conditions and on its physico-chemical characteristics. For instance, ANFO effficiency increases whereas AN porosity is higher and consequently loading density of the explosive is less. This can be argued against generally admitted ideas. Therefore, the efficiency of industrial explosives related to ANFO (for example "relative weight strength" or "relative bulk strength") is a tool that must be used with caution.

Jan 1, 1993

By Gerard McAlinden, Daniel Frost, Patrick McAlinden, James McAlinden

In an effort to recover Polychlorinated biphenyls (PCB’s) that had leached into bedrock below the Hudson River in Upstate New York, a shaft and tunnel complex was designed that would allow installation of inclined and vertical wells into the zones of contamination to recover PCB’s by gravity. A joint venture of Merco Inc., of Lebanon, NJ, and Obayashi Corporation, of San Francisco, CA, was awarded the contract for constructing the first Tunnel Drain Collection System in the world. Conventional drill and blast techniques were the most economical method to construct the project but due to the presence of PCB’s and community concerns, innovative drill and blast practices were needed.

Jan 1, 2010

By David Porter, Nathan Rouse

The implementation of presplit perimeter control in underground mining as a method to decrease dilution yields positive benefits throughout the current and future mining cycles. A case study to understand the benefits of reducing overbreak and underbreak in a cut and fill mining cycle was performed to quantify the reduction in backbreak. The study was performed in a control section of the mine where a presplit perimeter control design was utilized for a length of heading. This control heading was then compared to the existing standard blasting design within the same mining zone. The comparison included multiple aspects of the mining advance including overbreak, dilution of waste, dilution of Cemented Rock Fill, bolt counts, and cycle times. Once mining in the control section was completed and mining commenced in adjacent headings, blast damage due to blast design could be quantified.

Feb 6, 2023

By Stephen G. Rieben

Almost everyone has at least heard of the two one-call systems which serve New England. They are "Call Before You Dig", which covers Connecticut, and "Dig Safe", which covers the remaining five New England states. Those of you who are more familiar with these programs know that it is our job to help guard against the accidental dig-ups of buried plant and to prevent facility service disruptions. We cover all types of buried facilities, from cable television to high pressure gas transmissions lines, telephone cables, electric facilities, fiber optics and everything in between

Jan 1, 1990

By Viktor Aranovich, Thomas E. Brown

The Almalyk Integrated Mining and Metallurgical Plant is located near Tashkant in Uzbekistan and is one of the former Soviet Union's largest copper producers. Almalyk consumes about 10,000 metric tonnes of explosives annually and expects this requirement to double by the end of the century as they implement a program to boost mine output.

Jan 1, 1998

By Stuart Brashear, Robert Brush, Ben Cook

In early 1993, the Piney River quarry owned and operated by the Blue Ridge Stone Corporation of W.W. Boxley, received a series of complaints from the owners of a 130 year-old historic farmhouse that had been converted into a bed and breakfast establishment. Since the distance from the quarry to the farmhouse was substantial, a unique method of seismic data acquisition was utilized to determine if perceived blast effects were caused by air blast or low amplitude, low frequency ground vibration.

Jan 1, 1995

By Neal Lee

Often the effects of wet boreholes are not taken into consideration when designing a blasting program to exhibit a certain amount of explosive energy per unit of rock such as design by powder factor, expressed in lbs./bcy (pounds explosives per bank cubic yard) or kg/bcm (kilograms per cubic meter), often the effects of wet holes are not considered. This paper examines different methods of loading wet holes and the effects they have on actual explosive quantities/unit of rock. In particular, we are looking at the amount of water trapped within the explosive column (bulk loading from the collar), or the annular space left void of explosives product around and between cartridges (wet-bags) with many of the current wet hole loading methods in use. We will focus on the effect this has on actual powder factor relative to “as designed” dry hole loading values, as well as the effect on performance of the explosives.

Jan 1, 2011

By Andrew Wetherelt

Blast vibrations are of paramount importance in a society where ever increasing development is putting more stringent requirements on their control. Increasing civil development and more complex extraction scenarios make the trade off between proficient vibration control and productivity difficult to ascertain. Historically, reduction of induced vibrations levels was achieved through a reduction of MIC’s leading to smaller but more frequent blasts in order to meet extraction targets.

Jan 1, 2007

By A. Vishwakarma, V. Himanshu, K. Dey

Underground mining is the most feasible method after extinction of shallow depth ore deposits. Longhole stoping method is the most technically advanced method for the faster excavation. In this method, the holes are drilled in the form of ring pattern and explosives are used for the rock breakage. During blasting, the explosive energy sometimes also breaks the non-ore material. The non-ore material gets included in the extracted ore and enhances the ore dilution. Few uncontrollable factors which affects the ore dilution are ore body characteristics, rock quality, insitu stress condition etc. Apart from uncontrollable factors, explosive energy and blast design also plays an immense role in ore dilution. In the blasting practice, the purpose is to effectively utilise the explosive energy for rock breakage. The optimum delay is required so that the blast holes attain adequate free face before the blasting. This paper deals with the optimisation of blast design parameters to reduce ore dilution in underground hard rock mining having narrow vein. The study was carried out using numerical simulation. The explicit dynamics based modeller of Ansys was used for this purpose. The parametric variations in the models were done to optimise the parameters. The burden has been optimised first by varying the width of the narrow vein. The blasts of a ring consisting of single hole were conducted in the model by varying the width of the narrow vein. The damage contour under different parametric variations were analysed. The experimental trial has been also carried out at Zawar Group of Mine, Rajasthan, India. The optimum parameter was decided based on the result of experimental trial and numerical simulation model. The output of the model shows that optimum burden for 3.5 m narrow vein width is 1.12 m and for 1.0 m, it is 1.54 m. This shows that the optimised burden is higher in the vein having lesser width as compared to the greater width. The presence of joints/changed media/interface (between the sidewall and narrow vein) is the major reason behind this. The wave gets reflected back very fast on coming in contact with joints in a 1.0 m narrow vein as compared to a 4.0 m narrow vein. This will quickly convert the compressive wave into tensile wave giving rise to tensile slabbing. Hence proper utilisation of explosive energy will take place for the breakage of rock mass when the width of the narrow vein is smaller. The burden obtained from the experimental trial and numerical simulation models is less than 2.0 %. Hence the numerical simulation based approach can be used for the assessment of the optimum burden for ring blasting in narrow vein under different geomining conditions. This helped in reducing ore dilution and maximization of ore recovery. In the future, empirical relationships may be developed by considering different geological discontinuity, the strength of the rock mass and explosive parameters.

Jan 1, 2024

By Josh Calnan, Paul M. Holmgren, Abigail N. Styer

Detonating cord is a staple of the explosives industry, used widely in the civil and defense industries. Detonating cord is a thin, flexible plastic tube filled with pentaerythritol tetranitrate (PETN). It has many applications in mining, construction and military disciplines. For civil applications, it is used to connect and initiate a series of blastholes in a desired pattern. In the defense sector, it can be used as a detonating agent, a priming agent or alone as an explosive charge. Research has been done to understand the initiation and detonation physics on the detonating cord. However, its sympathetic detonation characteristics needed to be further analyzed.

Feb 1, 2020

By Thomas E. Ricketts

Occidental Oil Shale Inc. has spent the last eight years at its Logan Wash. mine near DeBeque, Colorado, developing its modified in-situ oil shale process for obtaining oil from oil shale. Modified in-situ technology involves large underground chambers, or retorts, which are formed by mining out a minimal volume of rock to allow explosive expansion of the surrounding rock into tile mined void volumes. The resulting rubblized retort volume must contain a fairly uniform particle size distribution and void distribution to permit maximum oil recovery during subsequent in-situ processing operations. The more uniform the rubblized volume of particles, the more oil recovery obtained during processing. The processing involves first igniting the top of the retort and then. injecting air into the top of the retort to drive the combustion front downward through the entire rubblized volume. The oil is continuously collected at the bottom of the retort during the processing.

Jan 1, 1981

By Braden Lusk

The problem of predicting damage in densely developed areas due to incidental or malicious explosions is one of considerable importance to local, state, and federal governmental bodies. The difficulty of making such a prediction is confounded by the urban canyon phenomenon as the shock wave intensifies or rarefies depending upon the particular arrangement of buildings. The specific method detailed herein used a Computational Fluid Dynamics solver, ANSYS AUTODYN, to operate on Geographic Information Systems data, ArcGIS, which captured the geospatial relationship between the various buildings in downtown Oklahoma City, prior to the Murrah Building bombing. The model of Oklahoma City was first developed using the building footprints and elevations provided by the ArcGIS database. Due to the sheer size of the problem, the model was then subdivided into annular zones of increasing distance from the center of the blast. Each subsection was then solved using an Euler model in a cascading fashion with the output of the preceding model forming the input of the present model. To further reduce computational time, the size of the Euler nodes was increased at each stage as the section area increased. Due to the loss of precision in capturing peak pressure values when using larger size nodes, it was necessary to perform a transformation on the results using one dimensional wedge calculations with higher precision. The Murrah Building bombing event was an excellent case study due to its available ArcGIS data and the level of documentation of damage to surrounding structures due to the blast. The results from the staged CFD calculation were then used to develop a damage potential contour map. The documented incidents of damage in the area surrounding the Murrah building were then compared to the model generated damage potential contour map. Copyright ©

Jan 1, 2010

By F O. Otuonye

Full-face blasts were fired in a 12 x 8 ft drift of an underground hardrock mine in a basalt formation with porphyry copper to study the effects of drill pattern and explosive type on the size distribution of the resulting muckpile. Each muckpile produced by five full-face blasts was sampled four times with a scooptram equipped with a 5-cu yd bucket and the size distribution of the broken rock in each bucket was determined by screen analysis. Results show a strong dependence of the fragment size distribution of muckpile on the blast pattern and explosive type for a given rock type. The mean fragment size of the broken rock was compared with the predictive equations of other investigators. Random sampling of the muckpile from full-scale blasts and screen analyses of the samples are recommended in assessing the size distribution of the broken rock because of scaling errors that are inherent in full-scale blasts when designed from results of small-scale tests.

Jan 1, 1985

By Mark S. Stagg, Rolfe E. Otterness, Stephen A. Rholl

The Bureau of Mines fired seven test blasts in a 22-ft bench of limestone, screening the material to investigate the influence of explosive type and between row delays on fragmentation. Four 4-hole, single-row test shots were conducted evaluating dynamite, ANFO, emulsion, and a 60-40 emulsion-ANFO mix. Three 12-hole shots, with three rows of 4-holes, evaluated delays between rows of 24, 36, and 120 ms. Accurate in-hole electronic delays were used, firing within 1.5-ms of the nominal delay. All seven shots had a 6- to 7-ft burden, 10-ft spacing, with a hole diameter of 3-1/2 in fired on a 12-ms delay between holes in the row. The tests were instrumented with strain gauges grouted in the burden region examining stress wave and gas pressure effects. Fiber optic probes were used to confirm timing and to obtain detonation velocities.

Jan 1, 1989

By R L. Mayville

The author explains why the strategic location and important limestone reserves at Chattanooga Quarry led to a decision to extend operating life by continued benching down to lower levels. He discusses the steps taken to accomplish this objective. These include relocation of the primary crusher from the second level to the fourth level, pre-testing of explosives designs and powder factors, control of a substantial water problem, and computer monitoring of stone production costs.

Jan 1, 1984

By Lon D. Santis

The Code of Federal Regulations Title 30, Parts 56, 57, 75, and 77 require that detonators and explosives be separated by four inches of hardwood or equivalents when transported together in mines. This standard was developed to protect the explosives from initiation by the more sensitive detonators. The research reported here is an attempt to quantify the fire protection offered by four inches of red oak and other materials. Boxes with a volume of 6.75 cubic feet were made from four-inch thick rough green oak (RGO), two-inch thick RGO plied, two-inch thick #1 common (dried) red oak plied, and a metal/plywood composite. These and boxes meeting the Institute of Makers of Explosives' (IME) Safety Library Publication No. 22 were tested in bonfires. The boxes were instrumented with thermocouples, filled with detonators, and placed over a kerosene fire imparting about 16 kilowatts per square meter heat flux for up to 3 hours.

Jan 1, 1997

By John Kemeny

There are many methods used to predict blast fragmentation, including empirical and numerical models, field trials, and experience from ongoing blasting. All of these methods require an accurate measurement or prediction of the rock mass properties. These properties include the characteristics of the rock fractures, including fracture density, friction angle, orientation, length, roughness, fill, etc. They also include the hardness of the intact rock, water content, and other parameters. This paper describes three new technologies that can be used to automatically or semi-automatically obtain rock mass properties: digital image processing, 3D laserscanners, and drill monitoring systems. Each of these technologies is described, including the current state of the art, current limitations, and their future potential. Each of these three technologies has advantages and disadvantages. These new technologies, however, have the potential for providing accurate rock mass information in an automated and real time fashion. This information can then form the basis for a new generation of real-time, database driven blast fragmentation models.

Jan 1, 2004

By Ronald W. Roberts

For years, blasters have experienced near-misses, injuries, and yes, even fatalities as a result of the dangerous nature of our business. Yet, some blasters continue to portray the immortal attitude: nothing-would-or-could-ever-happened-to me syndrome. As we all know, that attitude can become disastrous to yourself or colleague(s).

Jan 1, 1996

By Virgil J. Stachura, Larry R. Fletcher

The Bureau of Mines conducted a series of delayed blasting experiments at a West Virginia contour coal mine which resulted in smoother highwalls. The highwalls were smoother due to reduced overbreak and inherently safer due to reduced likelihood of rockfall. Reduced overbreak was accomplished by an increase in the highwall hole delay intervals which changed the effective delay pattern geometry and the direction of burden movement. Three combinations of blast delay intervals in the highwall holes were tested: 1) 50 ms longer than the nominal design, 2) 50- and 100-ms longer delays in the nearest two rows that form the highwall, and 3) 100 ms longer than the nominal design. The mine's nominal blast design was a flat vee formed by 17-ms surface delays between holes and 42-ms surface delays between rows, with 200-ms in-the-hole delays. All three test designs produced highwall improvements over the nominal design with only occasional exceptions because of geologic variations.

Jan 1, 1985