Search Documents

By Damien Bretall, William Fourney

Due to the changing face of warfare there is an ever growing need to protect the underside of combat vehicles from mine blasts. This paper presents a new method to better characterize the pressure profiles experienced by a plate as the blast develops. The explosive deformation of a small-scale plate was recorded using synchronized high-speed digital cameras, and then analyzed using 3D Digital Image Correlation software. Time-varying pressure profiles were input into an axisymmetric FEM simulation by fitting curves to data obtained from tests using Kolsky bars to measure pressures. These were then modified to find possible profiles that produce the measured deformations. It was discovered that the final deformation cannot be determined from only total impulse or peak pressures, and that it is very sensitive to the time and spatial decay of the pressures.

Jan 1, 2009

By Joshua Hoffman, Braden Lusk, Kyle Perry

Shock tubes are used to simulate large-scale arena explosions without the use of full-scale arena sites that utilize large quantities of explosives. Instead, small explosive charges can be used to drive shock tubes. When this is done, the geometries of the explosive charges can alter the resulting pressure time curve. A common geometry chosen for the explosive charge is a sphere in order to be congruent with the spherical shockwave that emanates symmetrically in three dimensions from the detonation point. This paper reports on the findings from experiments that study the effects of altering the charge geometries and explosive types while keeping the TNT equivalency constant. Peak pressures and durations were affected by these changes. Directional phenomena are exaggerated by the use of certain charge shapes and detonation points. The speed of the detonation front in the explosive being greater than the speed of the shockwave in air played a critical role in the resulting pressure time waveforms. Waveform manipulation can be used to generate job specific waveforms that ultimately benefit the shock tube operators and their clients.

Jan 1, 2010

By John Tatom, Michelle Crull, Robert Conway

The US Department of Defense Explosives Safety Board is sponsoring the development of a risk-based explosives safety siting program, SAFER. The fragment and debris hazard generated at the potential explosion site (PES) is critical at an exposed site (ES) over a significant range of standoff distances. The Science Panel Impact Debris Evaluation and Review (SPIDER) test program has been planned to develop improved predictions for the hazards inside an ES by fragments and debris. Data will include the mass and velocity required for perforation of the test cross-section and the characteristics of all debris produced inside the ES.

Jan 1, 2010

By Adam Stremcha, John MacGregor

Initial planning called for 3 separate drop shafts and 3 separate vent shafts to be pulled back from the excavated tunnel with a large diameter raise bore machine. With time constraints and the raise bore machine already in high demand on other shafts, a more “traditional” drill and blast approach was taken on a few of the larger drop shafts. This decision proved to be not only cost effective, but also reduced schedule impact as the shafts were excavated simultaneously with the other raise bores.

Jan 1, 2010

By Tony Rorke, Tamara Wiseman

Due to the advancements in technology it becomes easier to obtain accurate measurements for mining, quarry, and construction operations even in the most remote places. The use of off-the-shelf photogrammetric imaging technology and unmanned aerial vehicles (UAVs) are becoming more common in the mining industry for blast design and surveying. Pattern optimization, face profiles, pre and post blast volumetric, stockpile measurements and mine mapping are all areas where these technologies can be used with ease.

Jan 1, 2015

By Francisco Sena Leite, Raquel Sobral, Vinicius Gouveia de Miranda, Céu Jesus

"The urgent need for improvements in the control and mitigation of environmental and social conditions associated with the extraction and processing of raw materials is increasingly a demand imposed by legal entities and institutions. Therefore, this present article proposes an improvement of the estimation in the magnitude of the vibrations resulting from rock blasting methodologies in the surrounding areas,incorporating the heterogeneity caused by uncontrollable parameters, such as geological andgeotechnical characteristics. This methodology combines the use of empirical vibration attenuation lawscommonly known and with terrain discretization techniques using Voronoi’s decomposition. For thevalidation assessment of this methodology, the data set collected and compiled is composed by 87 vibration measures collected in 16 sample points in one area of study of which 2/3 of the samples were used to create the model and 1/3 for the validation. Using normality tests for statistical residue analysis,it is possible to infer that this present model has null residual mean, as well as a smaller sum of residualerrors. Comparing the methodology present in this paper with the procedures executed nowadays, areduction of the errors associated with the estimation is obvious, highlighting a better characterization of the behavior of the vibrations associated with rock blasting."

Jan 1, 2017

By Carlos Agreda

A general review of the comminution theory and also the general differential equation of the comminution are described, analyzed and discussed in order to be applied to rock blasting. Some size distribution functions are reviewed and discussed to determine which of them represents better the cumulative low size distribution F(x) as a function of the nominal particle size (x), for the rock blasting fragmentation. Based on the mathematical comminution model before presented a formula to calculate the burden (B) is developed and discussed.

Jan 1, 1994

By Guillermo Lazcano Ríos, Jorge Parvez Aguirre, Alejandro G. Díaz Berríos, Felipe Rodriguez Alveal

Codelco's Chuquicamata Underground Division (DCHS) faces issues due to collapses in its subsidence streets, which hinders the advancement of the subsidence front and leads to the loss of areas and reserves. To address these issues, DCHS and Orica have developed a new excavation methodology based on pre-loading explosives in high drawbell. This methodology involves creating a high drawbell extending from the floor of the production level to the ceiling of the subsidence level, divided into two phases: upper and lower. A resin stemming is used to separate these phases. The excavation strategy adjusts to variables such as reception volume, fluffing, and excavation geometry, involving vertical pre-loading of the explosive and the use of a separating element between the phases. The test aims to validate the new excavation methodology and the retaining element in the rock mass, evaluating aspects such as drawbell geometry, impact on the rock mass, damage to the retaining element, and fragmentation. Wireless electronic detonators are used in the upper phase to improve safety by eliminating the need for physical connections, while traditional electronic detonators are employed in the lower phase. Low-density bulk emulsion is applied to minimize the impact on the Crown pillar and extraction point, and higher-density explosives are used above the subsidence level to ensure good caving. Results showed that the blast achieved 86% conformity with the theoretical design. Resin stemming allowed for 100% effective detonation in the upper columns, and the fragmentation obtained was 5.44 inches, which was less than expected. No damage to the Crown pillar was observed, and the explosive quality met standards. This technique has proven to be effective and viable, suggesting the possibility of eliminating the subsidence level in future levels, resulting in savings, and providing greater stability to the rock mass.

Jan 21, 2025

By Ruilin Lang

This paper presents an application of 3-D plots and non-linear regressions to define a sitespecific form of the charge weight scaled distance. The PPV (PPA) of single hole blasts is normally considered as a function of two independent variables - the charge weight and the distance. It is of great importance to obtain the relationship of the function accurately for a concerned site in terms of blast vibration analysis and modeling. However, in pre-computer time it was difficult to plot 3-D graphs. Consequently, a charge weight scaled distance was used to plot the PPV (or PPA) against the scaled distance as 2-D graphs. Blast vibration investigators use several forms of the charge weight scaled distances to plot data. We can exemplify them with the cube root of charge weight scaled distance, the square root of charge weight scaled distance, and other forms (Hossaini and Sen, 2004). Each of these scaled distances assumes relative contributions of the charge weight and the distance to the vibration attenuation. For example, the charge weight is assumed to have a less contribution to vibration in the cube root scaled distance than it is assumed in the square-root scaled distance. In reality, for different sites the relative contribution of the charge weight and the distance may be different and site-specific. This may explain that in some cases, the blast vibration data plots using these charge weight scaled distances are scattered. This could be largely due to the fact that the definition of the form of the charge weight scaled distance is not adequate for the particular site condition.

Jan 1, 2006

By Tom Treleaven

This guide presents numerous patterns that provide 8 millisecond separations between initiated charges. The guide is tabulated in seven sections to provide quick reference by number of decks or bunch blasting. The pattern is presented in the section where the highest number of decks works. It should be noted that patterns applicable to multiple deck shootings are also applicable for fewer decks.

Jan 1, 1997

By Keith Best

It has been said that when a person does something right no one remembers but when they do something wrong no one forgets. This statement, when applied to the explosives industry, has never been truer. Think about it.How many times have you seen a news crew reporting on how well a blaster is doing his/her job? Normally, all you will see is how bad things are going and how much “damage” is being done.

Jan 1, 2008

By Manuel Gutierrez, Roberto Gomez, Juan Aravena, Johan Gjoevad

The use of explosives in mining operations is a process that involves the search for an ideal explosive for the type of geological condition of the mineral to be extracted. For the explosives present on the market the majority are based on Ammonium Nitrate. This as it is an ideal balance of high energy efficiency achieved with low development of gas emission. The manufacturing and loading operation of the explosive requires multiple process stages and different raw materials, which, if is not correctly supervised and controlled may cause the development of harmful gases or, in the worst case, even toxic gases. The majority of mining operations are located at remote locations without the presence of communities, and hence individuals, which could be affected by emission of the harmful or even toxic gases. In these operations the protection is mainly to protect the employees of the operation. However, if the operation is located near communities, the effect of these gases becomes a serious problem. The communities' perception of post-blasting gases, according to interviews carried out in this project, describes these as smells of black gunpowder, damp soil with a volatile permanence and medium intensity, sometimes a stinking tone is added. The legislation in Chile that controls the exposure of “workers” to different gases is Supreme Decree 594, 2019 (Decreto Supremo 594). Currently the Chilean Ministry of Environment and Sernageomin (Servicio Nacional de Geología y Minería) are taking actions to reform and strengthen oversight, seeking through a short law to provide more tools to the government to decentralize decisions in case of non-compliance with the decree. This paper describes the development and implementation of a permanent and remote gas monitoring system, considering the reasons for choosing the gases to be included in the equipment, the types of sensors and their capabilities, the way to verify in the field the correct functioning of the technology throughout the project, and finally how the data collected in the field is meeting the government's expectations in terms of permanent and online reportability. Additionally, it addresses the continuity of gas monitoring in the community that will disappear in the short term due to the expansion of mining operations, thereby ensuring the protection of both workers and affected communities.

Jan 21, 2025

By Martin Langenderfer, Sergii Chertopalov, Catherine Johnson, Vadym Mochalin, William Fahrenholtz

The high temperature and high pressure of an explosive detonation can be used for the production of nanomaterials. The controlled detonation of explosive compositions along with the collection and characterization of reaction products encompasses a process known as detonation synthesis. The primary advantage of the method of detonation synthesis is the possibility for producing monocrystalline nanoparticles with diameters of less than 10 nm. In order to successfully synthesize nanomaterials via the detonation process, it is necessary that the explosive detonation is conducted in a sealed environment. This environment when pulled to a vacuum or purged with inert gas such as argon will reduce the oxidation of detonation reaction products. Detonation synthesis testing is currently being conducted in a 1.8 cubic meters (m3) (64.3 cubic feet (ft3)) ellipsoidal pressure vessel consisting of two interlocking half shells. The testing involves the controlled detonation of cast mixtures of Cyclotrimethylene-trinitramine (RDX) and 2,4,6-Trinitrotoluene (TNT) in conjunction with siliceous compounds to produce nanocrystalline diamond and silicon carbide. Alternative detonation environments including the presence of a cooling medium such as water or dry ice to absorb residual, post detonation, thermal energy and enhance the stability of the materials being produced have improved yield. Modifications to the explosive charge composition have an effect on the type and quantity of materials that can be produced. Doping of explosive charges with various organic and inorganic compounds has shown promise in the synthesis of materials that are difficult or uneconomical to produce through other methods. This paper outlines the process development of detonation synthesis facilities. Preparation of the pressure vessel to create a suitable detonation environment for the production of nanomaterials is examined. Formulation of explosive charge compositions and considerations involving test charge initiation are discussed in detail. Experimental results and analysis from initial testing as well as plans for future research are also evaluated.

Jan 1, 2018

By Raj K. Rajamani, Solomon A. Tucker, Michael K. McCarter

"In a study aimed at exploring possible improvements in operating performance at an Open Pit Copper (OPC) mine in the western U.S., the impact of blast energy changes on crushing performance was evaluated. OPC feeds its 3-stage crushing plant in 12-hour-day shifts with skarn ore from three domains: Pit_B (B), Pit_S Low-Grade (SLG) and Pit_S High-Grade (SHG), in the blending ratio 1:1:1 (B/SLG/SHG). Thecrushed product is fed to a 2-stage ball mill circuit. "

Jan 1, 2017

By Michael J. Sapko, Eric S. Weiss

The U.S. Bureau of Mines has been conducting research on the secondary explosion hazards associated with the mining of oil shale under gassy mine conditions. Explosive incendivity tests have been conducted in a 28 m~3 (1000 ft~3) gallery to evaluate the relative incendivity of experimental emulsion-ANFO blends. The incendivity was measured by determining the minimum inert stemming requirements for preventing the ignition of a methane-air atmosphere by the discharge of hot detonation products from a 5.7 cm (2.25 in) diameter borehole.

Jan 1, 1990

By W. L. Saunders, Richard T. Dana

The dynamites are graded according to the percentage of nitroglycerin that they contain. Thus a “40% powder” would be one in which the sticks, weighing one-half pound each, would include one-fifth of a pound of pure nitroglycerin. Dynamite is usually packed in paper cartridges weighing about one-half pound each which will vary in diameter. When ordering, it is customary to specify a size of cartridge that will as nearly as possible fill the drill hole, the commonest size being 1 ¼” in diameter by 8” in length. It is nearly always shipped in 50-lb. boxes, which have a volumetric capacity of 3/4 cu.ft.

Jan 1, 2013

By Kevin Phelps, Jason Baird, Philip Mulligan, Dominique Nolan

Determining the transitions from run-up to optimal cut length and optimal cut length to run down, without bias, from the penetration of a linear shaped charge (LSC) is difficult. The stresses applied to the targets during explosive testing can distort the targets in such a manner that determining the true distance of cut, penetration, or fracture can be demanding. Through the course of this research, it was observed that the researchers made many of the errors involved in the collection of data. Among these errors researchers found problems in: determining and fitting the sample to a single plane from which to read measurements, determining where along the path of cut the three phases of penetration transition, and the precision of measurement based on handheld tools and the human eye. This study looks at three methods of recording the data of a series of linear shaped charge tests. The tests resulted in samples which are not ideal for measuring with common laboratory devices like measuring tapes, calipers, or rulers. The first method utilized these common laboratory devices and the difficulties the authors experienced are described in this paper. The second and third methods involve digital photography, image manipulation, and the use of AutoCAD. Methods two and three are then compared to the simple observational method and discussion is made in regards to the precision and accuracy of each method.

Jan 1, 2013

By Paulo Couceiro, Juan Navarro

The impact of rock blasting fragmentation and heave on digging performance in open-pit mining operations is usually the first true indicator of blasting outcomes. Within the typical excavation cycle, the bucket loading time or instantaneous digging rate are the ones that present the strongest correlation with rock fragmentation size distribution, swelling, and shape of the muckpile, a part of rock mass hardness, equipment size, power, and others. As the efficiency of unit operations becomes increasingly important for long-term mining strategies, cost-effective approaches are needed to increase mine productivity. In this line, the performance of downstream operations, such as digging, hauling, and comminution, may be affected by the energy input in blasting. This requires a better understanding of the explosive’s energy role in such unit operations in order to drive consistent improvements. Therefore, this paper examines the impact of the explosive’s energy distribution on shovel diggability from production shots carried out with different explosives in an open pit gold mine, with the aim of modelling the interface between blasting and excavation.

Jan 21, 2025

By S. Lim, G. Walsh, V. Romero

The cable television show, Mythbusters, contacted the New Mexico Institute of Mining and Technology requesting a pressure gauge to be used in underwater testing. The requirements for the gauge were: it must be passive (i.e. require no power to function), it must indicate when a certain, pre-determined pressure was reached, and that indication was to be visual. A pressure gauge was developed, using standard, commercially available rupture discs, set to burst at 500 psi. Underwater testing was conducted using a 400 lb Pentolite charge. Test devices were set out at ranges from 50 to 200 feet from the seat of the blast. The rupture discs showed a lethal range up to 100 feet, but not at 150 feet. This result matched well with the behavior predicted through modeling and simple shock physics calculations. Additionally, the geometry between the incoming shock and the pressure gauge did not seem to have a strong effect on gauge performance.

Jan 1, 2009

1974 The Society of Explosives Engineers officially formed to “advance the art and science of explosives engineering” on August 20, 1974 in Pittsburgh, Pennsylvania.

Jan 1, 2010