Search Documents

By T. G. Sitharam, P. B. Choudhury

Prediction of ground vibration (peak particle velocity, PPV) and frequency is an important task in geoscience. Till date, many empirical equations are derived from conducting trial blasts in the mines, to arrive at attenuation predictors. These predictors are usually site dependant and hold good for one particular type of rock/strata. These predictors cannot be used for geologically different rocks/strata. This paper presents the application of support vector machine (SVM) model, for predicting blast induced ground vibration and frequency, using a one comprehensive model for three different types of rock. Inputs to the SVM model formulation involve twenty one parameters consisting of geotechnical properties of the rock mass, blast design geometry and explosive properties, and the output of the formulated model is peak particle velocity and its associated frequency. The data has been acquired from eight limestone mine, five coal mine and two manganese mines. The comprehensive SVM model is formulated using 400 datasets and tested with 143 datasets. The performance indicators to the model not only justify its formulation but also the advantages it has over site specific predictor models. The SVM model not only predicts PPV, with higher correlation coefficients as compared to predictor equations, but also the associated frequency.

Jan 1, 2010

By Kain Petterson, P D. Katsabanis

Blast fragmentation, determined using image analysis was correlated to drill monitoring parameters in an open pit operation. Average fragment size and 80% passing size showed strong correlation with specific energy of drilling as well as with torque, while the same passing sizes did not correlate well with the rate of penetration. It was also determined that the uniformity of fragmentation decreases with the specific energy of drilling. Thus drilling monitoring parameters appear to be valuable in determining the blastability of the rock mass, enabling adjustment of blast loading to respond to changing conditions in the rock mass.

Jan 1, 2013

By Agus Sasmito, Akash Adhikari, Srivatsan Jayaraman Sridharan, Purushotham Tukkaraja

Previous studies on blast fumes(CO + NO2) clearance and workplace re-entry time have overlooked the effects of toxic gases entrapped in the muckpile. The currently available models forcalculatingthe mine re-entry times assume that all post-blast fumes are emitted upon detonation. However,recentstudies reportedthat as much as 60% to 70% of the fumes or gases produced during an underground development blasting couldremain entrapped in the adjacent rock mass or in the muckpile. Entrapped fumes are slowly released,and when disturbed, high concentrations are released, representing a possible risk during the digging and transportation of the muckpile. This study uses CFD, SC-Flow software to understandthe behaviorof the entrapped fumes and theireffect on mine re-entry time.

Feb 1, 2020

By L. O. Souza, J. F. Gewher, M. P. Scussiatto, C. S. Mendonca, R. A. McClure, B. T. Kuckartz, J. Kloeckner

Blasting is the most effective and economical tool available to fragment and move rock for most applications. If properly executed, it can improve down-stream operations such as loading, hauling and crushing. It is not possible, however, to have full control over the energy released by the explosives when a poorly designed blast pattern is used. A poorly designed blast can produce serious damage to equipment and create a potentially hazardous condition to people. Advanced mining technology has been developed to address these potential hazards and optimize the blast pattern. This profiling technology can assist with blast planning and provide quick, precise data about the condition of the rock structure to be blasted. The 3G BlastMetrix system presented here uses three-dimensional (3D) stereo photogrammetry to model the rock mass in a fast, practical and safe manner. Through the image overlapping method, a 3D model is created with thousands of points that provide a significant amount of data regarding geology, geometry and topography conditions. The blasting plan can then be made in a way to optimize the rock fragmentation and avoid areas that could create flyrock. This paper is a case study concerning usage of stereo photogrammic surveying and borehole survey systems in a blasting operation at the Brazilian Quarry, Incopel. One 3D image of a drilled bench was generated using photogrammetry survey technology and the borehole survey data collected using the rodded Boretrak borehole survey system. Utilizing the minimum burden profile reports, explosive loading could be done accurately, resulting in an optimized blast with good heave and fragmentation as well as increased safety.

Jan 1, 2013

By Clarence Hall, Charles E. Monroe

Squibs, Fuse, and Detonators It has been made clear in the discussion of combustion and explosion and the description of various explosives that they can be caused to explode by various means. All of them can, under some circumstances, be made to explode by fire. Some of them can be caused to undergo a detonating explosion by setting off a detonator in contact with them. In blasting use is made of both these means for setting off explosives, the means used being determined by circumstances.

Jan 1, 2010

By Robert Hopler

Testing Stations Abroad At the Seventh International Congress of Applied Chemistry, Drs. Mente and Will communicated a paper on the above subject. All large coal-getting countries employ testing stations of some kind, in order to safeguard, to the highest possible extent, the lives of the men employed in this industry. Most countries employ galleries of considerable diameter, and fairly short length; but within recent times, long galleries, with drives and other accessories approaching as closely as possible the actual conditions of mining have been installed. The following are the details of the testing stations employed in the countries mentioned.

Jan 1, 2010

By Travis Davidsavor, David Provost

A segment of high-pressure steel petroleum pipeline needed to be replaced on a hillside and beneath a waterway within an existing right-of-way containing multiple petroleum pipelines. The pipeline replacement required excavation of sedimentary rock to allow placement of the new pipe. As a result of an existing right-of-way limitation, steep slopes, and hard rock, blasting would be required as close as 7.8 meters (25 feet) from two operating pipelines. Existing pipeline company standards would have effectively precluded the construction of the replacement pipe by blasting rock. To facilitate the required construction and evaluate actual pipe stress during blasting to ensure pipeline integrity, a comprehensive evaluation methodology was developed by a team of pipeline, mechanical, geotechnical, instrumentation, and blasting engineers. A total of 60 strain gages were affixed to the steel pipe and seismographs were buried at the surface near the blasting area. Test blasting allowed pipe stresses with corresponding ground motion to be monitored. A conservative analysis approach evaluated individual peak strains and revealed that only small pipeline strains, and therefore stresses, were induced in the pipeline as a result of blasting. This evaluation allowed specific procedures to be developed to inform the blasting operation of maximum explosive loading and minimum charge distances. Additionally, this effort provided the pipeline operator with appropriate pipeline operating pressures during blasting activities to limit total stresses in the pipeline to be below allowable stresses imposed by code, regulators, and company operational limitations. Recommendations were developed to measure the blast generated ground vibrations with seismographs buried at the depth of the pipe, near the pipe, and limit the ground vibrations from blasting to 150 mm/s (6 in/s). If ground vibration intensities of 120 mm/s (4 in/s) or more were observed, additional engineering review is recommended. Finally, all blasting would be suspended and all activities reviewed at peak ground vibration intensities of 230 mm/s (9 in/s). The evaluation effort resulted in effective and efficient construction of the pipeline replacement and allowed the pipeline operator to better understand blasting induced stresses on their assets.

By Jennifer Williams, Donald J. Berger

Originally built between 1913 and 1916, the Ashton Dam & Hydroelectric Facility has experienced various seepage and piping incidents since completion. Ashton Dam is located within 15 miles (24 km) of the historical Teton Dam failure site and about 2.3 miles (3.7 km) west of Ashton, Idaho. Numerous repairs conducted over the years ranged from filling sinkholes on the crest of the dam to placement of rockfill on the upstream slope to improve seismic stability. In addition, the existing low level outlet works was grouted full and abandoned in 1991 due to significant vibrations induced on the dam during its operation.

Jan 1, 2014

By Travis A. Davidsavor, David A. Provost

A segment of high-pressure steel petroleum pipeline needed to be replaced on a hillside and beneath a waterway within an existing right-of-way containing multiple petroleum pipelines. The pipeline replacement required excavation of sedimentary rock to allow placement of the new pipe. As a result of an existing right-of-way limitation, steep slopes, and hard rock, blasting would be required as close as 7.8 meters (25 feet) from two operating pipelines.

Feb 1, 2020

By P. Couceiro, J. Navarro

A new methodology to perform selective blast designs by adapting the explosive energy, hole by hole (or in the hole), to the rock properties as a combination of their strength properties through the X-Rock model has been developed based on drill-monitoring data from both autonomous and manual rotary drilling modes. For that, a thorough normalization process has been developed to minimize external influences in the data induced by the different rig system and the operator interventions during manual drilling operation. Principal component analysis has been used to combine drill monitoring information. Data from 48,385 blastholes, comprised in 102 production blasts at 7 different levels in one expansion of the mine have been used for the analysis. The methodology, called X-Energy, combines the X-Rock model outputs with actual blast design parameters (drill pattern, stemming and borehole length, explosive mass/density and others) and a constant variable obtained from a machine learning algorithm, to estimate size distribution and percentage of fines and coarse material, hole by hole, by combining and recalibrating the Kuznetsov (Cunningham, 1987) based equation. From it, a new shovel-independent diggability model has been developed as combination of the P80 size, the rock properties (from the X-Rock) and a constant variable obtained from a machine learning algorithm. The X-Energy application presented in this study have been implemented in Minera Escondida Limitada (MEL), to design and operate production blasts with the goal of varying the explosive density to the rock properties to obtain a more uniform size distribution and digging rates, hole by hole, based on a target size and rate, and improving slope care, preventing active faults to fail. The methodology has been applied and validated in 17 production blast (8,277 blasthole), unlocking an average of 12.8% reduction in explosives costs (explosive consumption), by combining a pattern expansion strategy and a better distribution of the explosive density within the blast. The results demonstrate how a better distribution of the explosive energy by varying its density in the hole according to the rock and blast geometry variables can reduce powder factor (explosive consumption) while improving or maintaining blasting and digging results.

Jan 1, 2024

By DuPont Magazine

RBH Note: as stated many times in these articles, frozen dynamite was one of the greatest hazards facing the blaster. It wasn’t until the late 1920s that it was solved for good, with the introduction of nitrated ethylene glycol as a partial replacement for nitroglycerin in dynamites. The du Pont low freezing dynamites contained TNT, DNT, or nitro-substitution compounds of various sorts.

Jan 1, 2015

By Ali Kahriman, Abdulkadir Karadogan, Alper Celtikci, Ahmet Varol, Ertugrul Kaya, Turgay Ozat

This paper presents analysis of environmental effects induced by cautious blasting during the construction of the Istanbul Subway 4 Levent - Ayazaga Darulsafaka Metro Tunnel Project carried out by the contractor, located at Northern Istanbul in Turkey. Within the scope of the study, for the prediction of the peak particle velocity and to determine the slope of the attenuation curves together with the maximum charge per delay for the S6-7-8 shafts of this tunnel route, ground vibration components were measured carefully by using five vibration monitors during the construction of the tunnels which required blasting. The particle velocities and frequency values of all blast events are evaluated according to the United States Bureau of Mines (USBM) and German DIN 4150 Norms in order to predict, and compare the influence grades to the neighboring buildings, and structures. Also, data pairs of scaled distance and peak particle velocity obtained from 107 records belong to 51 shots were analyzed statistically. Empirical relationships with correlation at the 95 % confidence interval were established for these tunnel excavations and suggested for the test sites in order to estimate particle velocity of the ground vibrations. As a result of the studies, some practical charts are created in order to minimize the psychological effects of the shots, and simplify the authorities of shots’ job. And last but not least, make sure that the shots will be done in a controlled way.

Jan 1, 2011

By D. Lansburg

Electronic detonators are increasingly being used in today’s blasting in quarries, seismic, surface and underground mines. Electronic detonators offer several distinctive features over electric and non-el (shock tube) detonators including better timing accuracy resulting in excellent fragmentation and vibration control, field programmability and digital safety means. Because of the prerequisite electrical communications between the electronic detonators and the blasting machine, the layout or hook-up of these detonators can play an important role in obtaining the communication fidelity.

Jan 1, 2011

By F Ouchterlony

Soviet precursors to Cunningham’s Kuz-Ram model from 1983 are described. They are rooted in the mean fragment size and Rosin-Rammler (RR) fits to sieving data and rely on approximations. Three versions of Kuz-Ram model are presented and all three are de facto based on the median fragment size x50, even if the term mean is used in the papers. This discrepancy caused Spathis in 2004 to suggest a correction procedure for the Kuz-Ram rock factor A, which was said to explain some of the missing fines in the model. This correction, while applicable to Cunningham’s 1983 paper, does not apply to his 1987 paper in which he presents his own A factor. Common fixes of the Kuz-Ram model’s fines issue are fragmentation models where the fines are mainly generated in a crushed zone around a blast hole. This is contradicted by careful model blasting tests. The lack of a largest block size in the RR function may lead to spurious values of the uniformity coefficient n, e.g. in conjunction with image based fragmentation measurements or crusher modeling. These issues may be solved by using the transformed RR function, which has a largest block size xmax or its replacement by the Swebrec function such as in the KCO model.

Jan 1, 2016

By Soseol Kim

A high-performance Emulsion-based booster explosives has been developed that can be used as a booster for bulk explosives. Currently, Pentolite booster, which is mainly used as a booster for bulk explosives, has a high risk of accidents due to the sensitivity of its raw materials PETN and TNT, and has a low melting point, making it impossible to use it in high-temperature ground. The Emulsion-based booster was developed to maximize the Velocity of Detonation (VOD) while elimination the shortcomings of the Pentolite booster. The VOD of the Emulsion-based booster is about 6,500m/s, so it can maximize the performance of the bulk explosive. In addition, it can be used in high-temperature ground and does not cause accidental detonation due to the external environment. In this article, the performance of the Emulsion booster was verifies through comparative test blasting of the developed Emulsion-based booster and Pentolite booster.

Feb 6, 2023

By Chanhwi Shin, Hyeongmin Kang

Mine optimization is a key strategy in the mining industry that focuses on improving the efficiency, productivity, and sustainability of mining operations. To achieve mine optimization, digitalization is essential for modernizing mining operations and attaining optimal performance. Due to the importance of mine digitalization, various software and platforms have been released to support this effort. Furthermore, by integrating these advanced technologies, mines can enhance processes, leading to significant economic and operational benefits. However, integrating data from various sources and collaborating across different platforms remains a significant challenge in the mining industry. Generally, data for mine optimization, such as mapping, smart drilling, FMS (Fleet Management Systems), fragmentation analysis, or vibration analysis, are collected and analyzed separately on different platforms. This separation makes it difficult to aggregate and utilize data comprehensively for overall mining process optimization. During the digitalization process, obstacles arise due to these complexity, variability, and sharing issues of data across different maker, sources, and methods. These challenges highlight the need for seamless integration to achieve optimal mining operations. Thus, this study applied a total solution that can cover the entire Drilling and Blasting (D&B) processes. The blast design was performed using actual terrain mapping data, and drilling and charging were conducted following a guide based on the blast design plan. After blasting, loading and hauling distances and fuel consumption were measured, and fragmentation for each blast was evaluated. All measurement tasks were automated to minimize human error. By collecting all data in one server, it became possible to perform an overall evaluation for each blast, allowing the identification of optimal values. In conclusion, to evaluate the optimization effects for each mining process, one month of integrated data collected on a single server was used. Compared to the period before the Total solution was implemented, there were notable improvements: a 25% enhancement in hole spacing, a 60% improvement in floor flatness, a 23% reduction in average fragment size, and a 19% improvement in fragment uniformity. Regarding cost savings per blasting volume, the improvements were 11.7% in drilling, 9.3% in explosives, 7.6% in loading, and 17.5% in hauling.

Jan 21, 2025

By Guillermo Silva

A novel, ultra-low density explosive composition, particularly suited for wall control and other applications requiring customising of the explosive’s energy output, has been developed. Being reactive in nature, the low density explosive enables the controlled dilution of dry blasting agents from their nominal densities down to values slightly less than 0.10 g/cm3. The product has been detonated at densities of 0.07 g/cm3 in diameters as small as 50mm under confined conditions, using a 227 g (l/2 lb.) primer. Recorded velocities of detonation ranged between 1200 m/set and 2200 m/set for densities between 0.07 and 0.2 g/cm3. Theoretical velocities ranged from 1700 m/s to 2500 m/s for the same density range. The low density explosive was insensitive to initiation by a blasting cap which is a desirable feature for transportation purposes. Mixing of the product with ANFO has been accomplished with minimum segregation making it suitable for applications where reduction of pressures are necessary.

Jan 1, 2000

By Martin Langenderfer, Catherine Johnson, Phillip Mulligan, Kelly Williams

The physical geometry of a charge has a direct correlation to the geometry of the shock wave. This relationship appears strongest within the boundaries of the visible fireball. As the shock wave propagates outward past the limits of the fireball, the theory states that the geometry of the shock wave should even out and become more spherical. This paper investigates pressure vs. time at two distances, one ‘Near Field’ at the extent of the fireball and one ‘Far Field.' The two Fields were instrumented with three free-Field pressure probes from PCB oriented at 0, 45, and 90 degrees to the front face of the charge, in the same horizontal plane as the charge. This orientation allows for the comparison of the shock wave from the face and vertices of the charge. All the pressure sensors were connected to a Data Acquisition System (DAS) recording at 2 million samples per second (2MS/s). Two high-speed cameras, a Phantom and an MREL Ranger II, recorded the detonations for qualitative examination of the fireball, and the shock wave. Three charge geometries were used and compared to the shock propagation of a sphere. The other geometries tested are cylinders, cubes, and tetrahedrons. Charges were made from a PETN based sheet explosive. In the Near Field, a lower pressure is observed along charge vertices with highest pressures from each face. In the Far Field, vertices record a higher pressure, possibly due to the shock waves from the adjacent faces intersecting, indicating that shock pressures do not always even out in the Far Field. This paper will describe the methodology and findings of this experiment and attempt to determine causality for trends in the data gathered.

Jan 1, 2018

By James W. Reil, Douglas A. Anderson, Steven L. Burchell

A total of 26 full-scale production blasts at three sites were extensively monitored with sophisticated instrumentation systems to determine the benefits of more accurate detonators. The new and more accurate MS electric Masterdet detonator was tested against conventional detonators to determine any increase in productivity outputs. All blast design parameters between paired blasts were kept as constant as possible with the only difference being the inherent accuracy of both detonator systems.

Jan 1, 1986

By Andreas Gaich

A new 3D fragmentation analysis method for muck piles is presented. It works with aerial imagery from UAVs (drones) and handles entire muck piles with minimum user intervention.

Feb 1, 2020