Search Documents

By David R. Ziegler

The concept and facts concerning "threshold blast damage" are not considered "general knowledge". Perhaps because of a lack of knowledge, understanding, and experience of blasting effects, property owners and lay-persons may attribute a wide range of common cosmetic conditions to "blasting damage".

Jan 1, 1997

By John Montgomery

This paper discusses the major changes to the Commissioners Rules and Regulations, Chapter 120-3-10 “Rules and Regulations for Explosives and Blasting Agents”; how the changes came about, and a summary of the status of the blasting industry in Georgia.

Jan 1, 2003

By Rachel L. Bauer, Catherine E. Johnson

Explosive demolition involves first, the use of cutting charges to sever a column and second, kicker charges to move it out of alignment. Dynamite is the traditional explosive used in kicker charges as it is inexpensive, easy to initiate, and has a consistent track record of use. Dynamite, however, has health concerns in handling, fragmentation concerns from direct contact on the beam, and availability concerns due to being manufactured at only one location in the continental United States. Recently, water-cased kicker charges have been used in industry, and research has shown that a reduced dynamite mass is possible due to the added confinement, for energetic performance, and the incompressible fluid, which aids in the transfer of explosive energy into beam movement. This research will compare two different explosives, an emulsion (DYNO AP), and binary (HELIX), to dynamite for use in kicker charges, both with and without water-casing. Emulsion is commonly used in rock blasting to create a large push or throw due to its high gas volume production which could translate to kicker charge movement. HELIX is a binary explosive commonly used by the military in breaching charges with water backing. Experimental tests placed kicker charges at the base of a hanging steel column, modifying the ballistic mortar test used to determine explosive power. The study shows that water-casing effectively reduces air overpressure and enhances explosive performance. Among the tested explosives, HELIX showed the most substantial improvements with a 1.8 dB reduction in air overpressure and a 3.2 m/s (10.5 ft/s) increase in column velocity when water-cased. Dynamite and emulsion also benefited from water casing, with decreases in air overpressure (1.1 and 0.7 dB respectively) and increases in column velocity (1.1 and 0.7 m/s (3.6 and 2.3 ft/s) respectively). This research also shows that emulsion is a viable replacement for dynamite in demolition projects, performing similarly in both traditional use and water-cased charges.

Jan 21, 2025

By Jorge Cárdenas, Alejandro Luna

In mining simulation for fragmentation results prediction is of utmost importance to study feasibility, ensure safety, and estimate the correct use of resources in drilling an explosive to meet requirements and avoid excessive usage. One critical case is fragmentation prediction, developed through models. Developing a fragmentation model in a mining unit aims to control blasting results to align theoretical and real data and improve correlation. Therefore, it is essential to collect post-blast fragmentation data, organize it, and systematically process it to develop a suitable model that meets variable requirements. Using a robust system of equations, this model should generate the required results with minimal variability between simulation and actual results. Additionally, this model must be adaptive to reduce this variability. Studying the most known and used models in mining resulted in our work correlating Cunningham 2006, Swebrec, and CZM models. Thus, the Simfrag model was created, presenting a robust foundation and combining the most notable advantages of the aforementioned models.

Jan 21, 2025

By L D. Lawrence

Certain blasting applications are more prone to the generation of significant levels of nitrogen dioxide post blast fumes, more commonly referred to as after blast smoke, generally ranging in color from dark yellow to bright red. This paper reviews basic background chemistry defining the observed fumes and attempts to correlate geology, blast design, and explosive composition effects on the level of nitrogen dioxide that can be observed in various blasting conditions. Additionally, a test setting for evaluating the generation of post blast fumes is presented with pertinent test data detailing generic explosive formulation modifications which effect the overall level of post detonation generation of nitrogen dioxide.

Jan 1, 1996

By Douglas A. Anderson

The US Bureau of Mines, in RI 8507, has shown that blast vibrations at low frequency are more likely to cause damage and complaints than those at higher frequency. Since that publication in 1980, the Office of Surface Mining and many state and local regulatory authorities have incorporated frequency in their regulations for acceptable ground vibration from blasting. Even when frequency is not explicitly stated in regulations, it may become an issue in hearings or in court.

Jan 1, 1992

By Jim Breedlove, Stephen P. Case, Mike Fabio

To meet salt production needs over the remaining life of the Cayuga Mine at Lansing, New York, the Salt Division of Cargill, Inc. decided to build a new underground screening plant. The new plant required a chamber 50 feet wide by 250 feet long and nearly 70 feet high. On advice of their mining contractor, Dynatec Mining Company, the company chose an ingenious excavation method similar to sublevel stoping. This method eliminated the need for an access ramp, reduced equipment needs and excavation time substantially.

Jan 1, 1996

By Lance McAnnuff

Whatever system is devised to control noise and ground vibration from blasting operations must present an effective compromise between the rights of the individual to be undisturbed by the actions of others, and the necessity for society, the whole of the population individually and collectively, to have the services and the products of commerce, industry and transportation along with the relaxation of recreational and cultural pursuits, all at a price within the means of the same society. One of the first jurisdictions in North America to attempt to quantify acceptable environmental limits for specific blasting operations was Ontario, Canada’s largest and most populous province. A process for development of guidelines applicable only to quarries and strip-mining operations was begun in 1974 and culminated with their inclusion in a “Model By-Law” published by the Ontario Ministry of the Environment in August 1978. This paper examines the process of development of the final guideline document and its application over the last 25 years. While acknowledging that the published guidelines for air blast and ground vibration control have provided a useful and generally workable framework for the purposes of land use planning and complaint or damage claim reduction, a number of flaws, weaknesses and misinterpretations connected with their application are identified. Recommendations for amendment of the controversial items are submitted with a view to making these and potentially similar guidelines in other jurisdictions, more acceptable to both government and industry.

Jan 1, 2004

By R. Jacob

Mining has been around for a long time, and new deposits are being discovered continually but are becoming more complex for processing and typically sulfide in nature. Most of the large easy deposits with simplified and cheaper to process oxide material have been mined or the deposits are locked up with legal or social issues and may never be mined. It is common to see the mines today being evaluated to mine have little in oxides and have a sulfide component to the deposit. This creates a problem with explosives being selected for the mine because ANFO could cause a reactive ground issue. When evaluating the cost component of mining for future mines, ANFO is the go-to selected bulk explosive because of the cost and effectiveness. More work needs to be done by projects evaluating costs by properly testing the ground and water conditions to match the correct bulk explosive for the ground conditions of the mine. This will prevent a possible safety hazard and the best result for the mine.

Feb 6, 2023

By Tianrui Xu, Chaohong Liu, Bangqing Ding

The authors were responsible for a series of large scale multiple chamber charge blasts conducted in the granite mountain area for making construction space on the southeast sea coast in China during 1993-1996. This paper describes the blast design and damage control of one mountain blast 320m in length and 280m in width in the vicinity of two wharfs and a dam. In order to obtain better rock fragmentation and muckpile, the explosive charge should be well-distributed in the mountain. The charge pattern, therefore, was designed with mainly 5 rows of tunnel charge in regular terrain in combination with a chamber charge in irregular topography area and the maximum burden was limited to be less than 38m. In order to protect the dam and wharfs the firing sequence was carefully arranged in 29 intervals and the distance between different charges of the same delay to the dam or wharf was taken into account as an additional delay interval based on the difference of p-wave propagating times. The maximum charge fired in an interval was also limited to less than 34t explosives through dividing the larger charge by a stemming deck.

Jan 1, 1998

By Russell D. Melton, Gary A. Kanelos

A construction company performed blasting operations to break up limestone bedrock for excavation of residential basements. The owners of an existing residence located approximately 400 feet from the operation claimed that vibration damaged the structure and created foundation subsidence by lowering the moisture content of the foundation soils.

Jan 1, 1996

By Jeremiah Cohn, Rachel L. Bauer, Catherine E. Johnson

Water is frequently used in explosive applications to increase explosive performance and reduce air overpressure. Water tamping can enhance cutting abilities of shaped charges in demolition and increase impulse of kicking or breaching charges. In explosive disposal, water is used to suppress air overpressure and reduce noise. Despite its widespread use, the specific effect of water placement, whether in front of or behind the explosive, has not been studied. This work evaluates the directional effects of water placement on blast performance using 400-gram sheet explosive charges in five configurations: no water (control), rear-only water (tamped), front-only water (pushed), water on both sides (confined), and a thin front-and-rear water layer (low mass confined) to assess reduced mass effects. Water was sealed in plastic bags and held in position with custom 3D-printed cages to ensure consistent geometry and contact. A modified ballistic pendulum consisting of a hanging steel W-beam was used to evaluate impulse transfer, with high-speed video capturing swing velocity. Air overpressure was recorded using a seismograph microphone. Rear-only water (tamping) increased beam swing velocity by 69% over the control while confinement with water on both sides increased performance by 12% at a 2:1 water-to-explosive ratio and by 50% at 4:1, though it still underperformed the tamped-only configuration. Pushed water alone did not increase beam momentum and reduced tamping effectiveness by 19% when combined. Seismograph microphone data showed that pushed and low mass confined water configurations produced some of the highest air overpressure levels (up to 139.2 dB), while tamped and control charges produced lower levels (~134–136 dB), suggesting that pushed water may amplify, rather than mitigate, air shock transmission. These findings show that water placement has a strong directional influence on blast dynamics: water behind a charge enhances energy transfer to the target, while water in front provides limited or potentially counterproductive mitigation. This study advances understanding of water–explosive interactions and will lead to more effective charge designs for breaching, disposal, and demolition.

Jan 26, 2026

By F. Schott, M. James, G. May, E. Baker, C. Johnson, R. Bauer

Explosive demolition typically utilizes cutting charges to sever columns, detonating cord to time charges and provide an initiation path, and dynamite as a kicker charge. The kicker charges of dynamite are used to “move” columns out of alignment, causing collapse. Demolition projects involving dynamite can pose significant health and safety risks to workers and the public. Nitroglycerin in dynamite can cause dizziness, fainting, and other health problems. Moreover, dynamite placed directly on columns can result in fragmentation and cutoffs, preventing other charges from being initiated and resulting in incomplete demolition. Fragmentation can occur from columns and travel significant distances from the initiation point, sometimes reaching hundreds of meters away. This fragmentation can pose serious dangers to anyone in the vicinity, including workers and members of the public, as the debris can cause severe injuries and property damage. The force and velocity of the fragmented material can be unpredictable and difficult to control, making it important to take proper safety precautions and consider alternative demolition methods that minimize the risk of fragmentation. Previous work concluded that casing charges in water showed that a reduced dynamite charge mass could still successfully kick the charge out of alignment. This study aims to investigate the use of Pentolite boosters in water-cased charges as a safer alternative to dynamite-based demolition. The research involved testing various amounts of dynamite and pentolite boosters in water to compare their effectiveness in moving a hanging W-beam, which swung freely like a ballistic pendulum. Water-cased charges consistently move the column at a higher velocity than the traditional dynamite charge placed directly on the column. The method of water-casing increased the area of impact and impulse felt by the column, improving demolition efficiency when compared to traditional demolition methods as found in previous studies. Pentolite water-cased charges moved the column at 7.8 meters/second (m/s) while the dynamite water charge moved the column at 5.9 m/s. The increased strength and explosive properties of the pentolite contributed to this increase in velocity. This study showed that it is feasible to remove dynamite from demolition projects by utilizing pentolite boosters and that when considering safety, explosive properties, and effectiveness, pentolite boosters can be cost effective as well.

Jan 1, 2024

By Jesús V. Saccsa, Kenji B. Loayza, Erick M. Condori, Jorge A. Velásquez

This research investigates how to reduce manufacturing costs of a safety fuse composed of black powder, replacing its ingredient NO3K by NO3Na for processing, and contributing to minimize costs per blasting.

Jan 1, 2017

By PHILIPP HARTLIEB, Peter Schimek, Thomas Seidl, Pablo Segarra, José A. Sanchidrián, Juan Navarro

This paper develops a new Blastability Index to assess hole-to-hole fragmentation in bench blasting based on a new Rock Factor exclusively obtained from drill-monitoring data, that can provide an automatic assessment of rock structure, strength, and waste/ore, the effective energy factor of the explosive and the delay time per blasthole.

Feb 1, 2020

By Sandra Penttinen

To assist blasting professionals with the creation, documentation, and appropriate methodology to standardize the data collection of the pre and post blast investigation process. Penttinen Associates will present a logical non-technical presentation focusing on: Why pre-blast surveys SAVE How to prepare for pre-blast inspections What to do in preparation of pre-blast inspections The creation of an industry standard all-inclusive pre-blast document Establishing pre-blast inspection operational standards Preserving the data.

Jan 1, 2001

By Jeffrey Loeb

Recent trends in blasting engineering and its related fields, at the level of professional academia, have tended to exclude detailed discussion and examination of the formative experiences of the engineering student. In particular, the extra-curricular aspects of the undergraduate program in engineering—focused, in this case, on the summer job—will be shown to contain a wealth of heretofore underappreciated knowledge in the field. In Surveying the Damage: Post Traumatic Stress and Pre-Blast Surveys, I intend to outline and examine some of the more unusual experiences afforded me by my work as a preblast surveyor in the summer of 2007. In this capacity, I was required to make a visual note of existing conditions of surrounding residential and commercial structures within 100 m (328 ft) of two separate blasting sites in central-east Ontario. In the interest of both convenience and specificity, I have attempted to organize the paper as a crossdiscipline survey of the field according to the conference’s list of suggested topics. In the paper’s first section, I will discuss the topic of Environmental Improvement and Remediation by using a case study in which not one, but two dead cats were found during the course of a routine pre-blast survey. The second section will undertake a discussion of on-site blaster gossip as an entry point into a wider discussion of Workplace Communications Management. In the paper’s final section, I will detail an early morning encounter with a 300 lb, stark-naked trailer park inhabitant as a cross-sectional analysis of the topics of Drilling in Hostile Environments, Vibration and Seismology (Sizemology?), Ethics in Blasting, Crisis Management, Risk Assessment and Public Relations. It is my hope that this paper will begin to open up a critical space for discussion of the formative experiences of engineering students during the undergraduate university program in terms of their far-reaching effects on later performance within the industry.

Jan 1, 2009

By Steve Dillingham

Blasting crews, explosive product drivers, drillers, blasters, supervisors, and salespeople all arrive daily at customer blast sites in vehicles of every type whether passenger cars, pickup trucks, or bulk trucks. The majority of these vehicles are company owned and re p re s e n t a substantial investment and risk for the company. That may explain why the costs resulting from blasting incidents is often surpassed by those involving motor vehicle accidents.

Jan 1, 2003

By Auã Kiahla, Tomi Kouvonen, Vinicius Miranda

Through numerical mathematical processing (Taylor’s approach and numerical derivation) the original data supplied by the accelerometer’s sensors was transformed into velocity and, after the data mining, a statistics residue analysis was applied in order to evaluate if the data from the prototype and from the traditional seismographs were similar. The data from each system was used to estimate the attenuation law and the results are shown in this paper

Feb 1, 2020

By B S. Petri, N T. Rouse

Underground limestone mines generally lack air pressure monitoring procedures and instrumentation guidelines. The blasting industry also lacks an applicable source for air overpressure levels that are produced by blasting operations in underground mines. This became apparent during the development of a new underground limestone mine, where overpressure levels from production blasting needed to be estimated. During the development phase of the mine, it was imperative that newly constructed underground structures be capable of withstanding the overpressure produced by blasting. Therefore, a study was conducted to (1) identify and review any published studies for data that may be applicable, (2) identify the appropriate equipment required to record the overpressure levels, (3) determine the proper procedures for setting up the equipment and recording overpressure, and (4) provide an understanding of the nature of the air overpressure in a developing mine.

Jan 1, 2014