Search Documents

By R. F. Favreau, Patrice Favreau

"Ever since we have started to assist those responsible for blasting with blast simulation studies, we havebecome aware of an interesting aspect, namely that in 90 % of cases we are asked ‘‘Can you seek ablasting method which gives better fragmentation than the method which we use now’’. But after a visit to the site, and the evaluation of the fragmentation obtained with their present blasting method, it very often becomes evident that it is the ease of mucking and not the fragmentation which requires improvement. Hence we then proceed to do a simulation study the results of which are improved mucking rather then more fragmentation, and those responsible for the blasting always become very satisfied."

Jan 1, 2017

By Tamara Whitaker, James Gunderson, Ruilin Yang

This paper presents the results of a vibration control project conducted in soft overburden at a surface coal mine located in the western United States. The study uses near-field blast vibration monitoring, analysis and modeling techniques developed in house. Accelerometer-equipped seismographs were utilized for near-field vibration monitoring and analysis. Vibration control was achieved through field data regression as well as vibration modeling using the multiple seed near-field blast vibration model (Yang and Scovira, 2007). The regression was conducted between peak particle vibration parameters and the minimum scaled distance per delay. From the regression analysis, the curves of upper bounds for peak particle vibration parameters and charge weight were developed. The dominant frequencies of the blast vibration were also addressed in this project. The regression curves and near-field vibration model guided the blast design to control blast vibration for maximizing the recovery of coal and maintaining mine productivity.

Jan 1, 2008

By G. Adderley, A. Wetherelt

The problems of poor drilling in underground operations have been highlighted on many occasions. Incorrect collaring and poor angular deviation can all lead to an increased block size, dilution, over-break adding to both cost and time, while in a tunnelling operation sidewall damage and a poor percentage pull from a blasted round has similar consequences. This paper sets out to further investigate the ability of the laser scanner method of obtaining drill hole deviations and collaring errors at the face as described by Wetherelt and Williams (2006). Tests were carried out to compare measured inter-hole burdens from this method in comparison to that obtained using a total station survey. To investigate the ability of these methods to accurately determine drilling errors, a field test was carried out through an analysis of a series of pre-drilled blast holes of known inclination and direction. A time-motion study was also conducted for a varied number of holes to assess the usability of each method. In line with current research into blast vibration being undertaken at the Camborne School of Mines, 6 cut blasts were carried out to establish the effect of poor drilling on a blasts success to see whether an increased burden at the toe of a hole had an influence on vibration.

Jan 1, 2009

By Enrique Albarrán, Julian Hernández

"In 1942 The “Presa Mixcoac” dam was built, along with 15 other dams, to control the rain fall waterin the mountains west of Mexico City. Mexico City’s population at that time was around 1.5 millionpeople, and the dam was way out of the city."

Jan 1, 2016

By Kyle Ott, Bernard Daly, Syed Haq, Douglas Anderson, Parsons Brinckerhoff

Drill and blast was determined to be the most cost-effective means of excavating the Raw Water Tunnel (RWT) for the Croton Water Treatment Plant in the Bronx, New York City. One of the major issues confronting project designers was the potential impact of blast vibrations on a major City Distribution Tunnel (CDT). The proposed path of the RWT would cross less than 30 meters (100 feet) above the CDT, which was built in 1917. Discussions with New York City Department of Environmental Protection led to vibration criteria on the CDT of 51 mm/sec (2 in/sec) peak particle velocity as an alert level, and 38 mm/sec (1.5 in/sec) as a review level.

Jan 1, 2012

The objective in control blasting is to reduce overbreak to control the final pit wall slope, shaft, drift, ditch, bench, etc. to the final planned excavation limit.

Jan 1, 1990

By Daniel Mallette, Richard Goodridge, C M. Lownds

Despite a world of mobile devices that has many of us taking the ability to communicate wirelessly for granted, an in-hole wireless initiation system was thought to be not viable. The known and common wireless communication techniques are not suited to this application. To overcome this, we have developed cutting edge technology to communicate to our initiating devices more than 1km through solid rock.

Jan 1, 2016

By Vic Sterner

As cities and towns continue to grow, the need to install sewer, water, gas and other utilities becomes a necessity and the blasting of trenches for these service lines probably constitutes one of the most important forms of blasting in built-up areas. There f o re, understanding how explosives can be safely used in the most efficient manner is of prime importance. The need for protection against flyrock must be emphasized. The first consideration is that all explosive c h a rges should be located well down in the blastholes. The golden rule is to ensure that the depth of top stemming is never less than the burden on the hole. In the case of shallow holes, the minimum depth of stemming should not be less than 18 times the charge diameter, if airblast and flyrock are to be controlled. If there is a doubt, then additional cover and/or blasting mats should be used. Putting too much burden on blastholes is another possible cause of flyrock and raising ground vibration levels. Overburdening of explosive charges will also result in the blastholes not breaking to grade. This in t u rn re q u i res additional drilling of shallow holes down in the trench to achieve grade, thus further increasing the h a z a rd of flyrock .

Jan 1, 2004

By Dale S. Preece

"Detonation delay timing has been an important aspect of quality rock blasting for decades. Detonators that enable delay timing have improved over the years especially with the recent advent of precision electronic detonators. The positive effects of precision delay timing have been observed repeatedly in the field with improved fragmentation, heave and overall blast control. Three-dimensional computational capabilities in terms of software, material models and computer speed have recently made possible the computer simulation of multiple blast holes in a bench configuration with precise delay timing between holes. Some of the key physical phenomena enabled by precise delay timing include: 1) collision and interaction of stress waves produced by adjacent blast holes, 2) reinforcement of stress waves from multiple holes as they reflect from the bench face and ground surface, 3) reflection of stress waves from “dynamic free surfaces” created by previously detonating holes, and 4) deformation induced fracturing, cracking and fragmentation. Simulating rock blasting in 3D has shed light on the physics involved and is resulting in an evolution of our understanding of fragmentation mechanisms. Routine use of these 3D computational tools will result in a much better understanding of the complex physics set in motion by the rock blasting process and allow predictionof improved blasting."

Jan 1, 2009

By Gregory Poole

With access to the World Wide Web, many resources are readily available for improving claim reports. With a little time spent on line, a more thorough report can be created. Claimants will accept the conclusions of a report more readily when they can view support information on their own computer, particularly when the support information is not just from blasting related web sites. Some suggested resources are discussed including aerial pictures, local tax maps, topographical maps and home repair web sites. This paper provides suggestions for tracking down support information on the web and information on how to properly reference this information. Case studies of several claim investigations are presented. These are some examples of how a little time spent online provided clear and convincing evidence to support the conclusions of the investigation.

Jan 1, 2006

By Harry Thompson

In using explosives to blast stumps from the ground in order to prepare it for farming, it is comparatively easy to place the charge under a stump having a semitaproot or a lateral system of rooting by boring or digging a hole in the earth to a point under the center of resistance and deep enough to give the desired effect.1

Jan 1, 2015

By William H. Highlands

Lightning is a natural phenomenon which poses a potential hazard to people, structures, and equipment unless adequate protection is provided. The type of protection required is related to the nature and of the facility. The decision making process involves a number of interrelated factors which should be considered when determining the need for protection.

Jan 1, 1989

By Lloyd Litwin

The ARTA 2008 Project (Alpha Ridge Test of Appurtenance) was a Canadian Government sponsored deep water seismic survey carried out on the high arctic permanent polar ice cap. This Geological Survey of Canada operation was the second seismic research project in the high Arctic and was monitored by the Danish Government. Utilizing 100% air support from Eureka and then helicopters from an ice based tent camp north of Ellesmere Island, the five week study was accomplished in the early spring just after the sun returned to the far north.

Jan 1, 2011

By Jorge Blázquez, Paulo Couceiro, Patricio Vergara, Luis Martínez, Juan Navarro

This study introduces the X-2Mill solution, a refined two-step methodology aimed at optimizing blast designs by aligning explosive energy with rock properties. The approach employs the X-4Traits Model, which uses drill-monitoring data from both autonomous and manual drilling modes to develop two critical indexes: the Drilling Rock Factor (DRF) and the Drilling SAG Power Index (DSPI). The DRF integrates the Size-Energy Fan Model with rock fragmentation results and blast design parameters, while the DSPI adjusts Specific SAG Energy (SESAG) based on Bond’s theory, incorporating ore X80 results, SAG mill capacity (TPH), and power draw to estimate milling difficulty. To enhance prediction accuracy, the X-2Mill solution incorporates, to a Principal Component Analysis of the normalized drilling data, a Meta Machine Learning model with a 3D spatial function, accounting for information from surrounding drill holes. This integration improves the precision of the DRF and DSPI estimates. The methodology unfolds in two main steps: Step 1: Bench-Scale Pattern Design, involves defining the target P80 size for ore based on the SESAG and the DSPI. It also establishes target X80 sizes for waste and oxide materials and iterates to determine the optimal Burden x Spacing (BxS) using the Size-Energy Fan Model and the DRF. Step 2: Blast-Scale Selective Explosive Density/Energy focuses on refining explosive density on a hole-by-hole basis to achieve the specified X80 values for ore, waste, and oxide materials. The X-2Mill Solution was developed at Minera Escondida Limitada (MEL) using data from 162,761 blastholes across 356 blasts conducted over three mine expansions. This solution addresses the challenges of blasting harder and more difficult rock, particularly in the lower levels of the mine. By adapting the blast pattern and explosive density to the specific rock properties and ore/waste designation, the X-2Mill Solution aims to achieve precise size distributions and improve overall blasting performance. The results demonstrate that the X-2Mill Solution balances ore fragmentation to meet SAG mill throughput requirements while optimizing powder factor costs for waste material and maintaining digging efficiency. By efficiently distributing explosive energy, the solution not only enhances throughput but also improves blasting efficiency while ensuring stable slopes and minimizing fault activation.

Jan 21, 2025

By Bruce Vandenberg

A 3D, PC based computer program is currently under development by Blasting Analysis International, Inc., to analyze the kinetics of full scale blasts with two or more high-speed motion picture cameras.

Jan 1, 1990

By Curtis G. Kremer

"New explosives initiation systems continue to be developed as new technologies make advancements possible. Due to recent initiator developments, explosives users now have the most reliable, accurate, safest and easy to use systems ever offered. Three initiation systems recentlyintroduced which offer significant improvement over standard electric and nonelectric initiation systems include Magnadet, EXEL high-strength shock tube, and Redundant two-Dath surface delay systems. These three systems will be discussed zn cecail with rmpiasis on their functioning, safety characteristics, ani specific application areas."

Jan 1, 1991

By Trevor Howie, Mal Edwards

"Thiess Contractors Pty Ltd. designed and operate the Mt Owen Mine in the Hunter Valley of NewSouth Wales, Australia on behalf of the owners of the mine, BHP Coal Pty Ltd. The mine is a multiseam open cut coal operation. Mining by Thiess commenced in September 1996 following thecompletion of the coal preparation plant. The location of the mine is shown below on Figure Al."

Jan 1, 1997

By David M. Langlais, Krystle Pelham

"Explosives used in blasting operations, natural and anthropogenic sources such as septic systems,fertilizers, and decomposing vegetation can potentially contaminate groundwater with nitrate in thevicinity of construction sites and make identification of blasting impacts difficult. Blasting operationsfor a private construction project in Windham, New Hampshire were indicated as the source of water quality impacts to private drinking water wells prompting the New Hampshire Department ofTransportation (NHDOT) to implement a proactive approach to limit the potential for impacts fromblasting for ongoing NHDOT projects. NHDOT has developed a baseline drinking water monitoringprogram designed to detect potential impacts and to ensure alternative drinking water is providedthroughout the construction phase of projects. In 2013, the U.S. Geological Survey (USGS) andNHDOT began a study to determine the source and fate of nitrogen compounds near blasting sites using a combination of isotopic, time series, geochemical, hydrologic, and geologic data. Approximately 1.75 million cubic yards (1.33 cubic meters) of rock were removed by blasting in several locations for roadway construction at a major highway construction site in southern New Hampshire."

Jan 1, 2016

By Benjamin Cebrian

Traditional dilution control systems range from computer modeling, use of physical markers on the field as polypipes to a technology that marks some control points where displacement is measured. The latter includes walking over a muckpile which is prohibited by some mining companies as a safety measure. The new technology presented in this paper is a patented system that is installed on board excavators (backhoe or front shovel types). Several control points are set along ore/waste contacts and their position is uploaded on the corresponding shovel. The operator proceeds on mucking until he is alerted when reaching any of the several control points previously located in the blast patterns and that have moved with the muckpile. A case study is presented at a high grade copper mine, were unique 3D shapes are showing as a result of using an on-board excavator dilution control system. Both ore-loss or dilution cost of opportunities are analyzed.

By Sadettin Bagdatli, Ali Kahriman, Umit Ozer, Alper Celtikci, Yucel Karakus

Due to population growth and rapid urbanization in Turkey, the need for the construction of residential units, transportation and infrastructure facilities has become increasingly more pressing. Since rock units encountered in the surface and underground in the construction of the subway, infrastructure and housing facilities, it is a necessity to use blast excavation methods. In recent years, large housing construction projects have been carried out especially in Turkish metropolitan areas, involving foundation excavations giving rise to great amounts of earthmoving. Since rock units encountered during foundation excavations are usually hard and solid, excavation with conventional machinery proves to be inadequate and unproductive, hence the necessity for the application of blasting technology.

Jan 1, 2014