Search Documents

By Dennis J. Viscusi, James H. III Rowland, Lon D. Santis, Mark H. Weslowski

This paper describes the procedure for analysis of toxic fumes from the detonation of high explosives using the Large Chamber at the U.S. Bureau of Mines (USBM), Pittsburgh Research Center (PRC). This test is specified in 30 Code of Federal Regulations (CFR) Part 15.20 (g) as a requirement for the Mine Safety and Health Administration's (MSHA) approval of an explosive as permissible for use in underground coal mines. The Large Chamber replaced the Bichel gauge and CrawshawJones (C-J) apparatus in the 1989 revision of these regulations. To determine the safety of an explosive in terms of toxic gas production, the Large Chamber Test attempts to simulate mine conditions and miners' exposure to toxic gases from explosives.

Jan 1, 1995

By A Lance McAnuff, Andrew Curic

Until relatively recently, underwater blasting operations for channel deepening, dock construction and pipeline crossings of lakes, rivers and streams were conducted without much regard for the potential side-effects on aquatic organisms.

Jan 1, 1997

By Gerald G. Schmitt, Richard D. Dick

Continuous Reflectometry for Radius vs Time Experiments (CORRTEX) was used to monitor several conditions of blasts such as the detonation velocity of the explosive column, the functioning of different types of initiators and initiation schemes, and the behavior of the stemming column confining the explosive. The CORRTEX data were also used to deduce the occurrence of dead pressing of ANFO slurry. Measurements of propagation speeds of shock waves in the stem column with various cables allowed some conclusions concerning bridging, stem failure, and stress levels in the stem.

Jan 1, 1985

By Winston Wilches B., Scott Scovira

This paper discusses recent changes to the emulsion blend blasting agent used at the Drummond Pribbenow Mine in Colombia, one of the world’s largest open pit coal mines, and the resulting improvements in rock breakage and excavator productivity. Based on field evaluations, the use of High Density Ammonium Nitrate (HDAN) can be effectively implemented in an emulsion blend blasting agent, yielding excellent results in terms of energy release, shelf life and velocity of detonation (VOD). Field evaluations showed that formulations using HDAN exceed the performance of the actual 50%/50% emulsion/ANFO blend using Porous Prill Ammonium Nitrate (PPAN). PPAN is conventionally used for emulsion blend manufacturing, with physical characteristics to facilitate sensitivity during the detonation process.

Jan 1, 2014

By Tristan Worsey, Nathan Rouse, Daykin Schnell

The authors were retained by a proposed underground metals mine operation to evaluate the potential blast vibration amplitudes that could be generated at surface structures above the proposed mine. Literature reviews of published blasting documentation gave little information, data, or models on surface blast vibrations produced by underground mines. At the client’s request, the authors contacted a number of underground mining operations to evaluate interest in sharing blast vibration data with the authors so that the authors could develop an underground-to-surface blast vibration regression equation. The authors worked with three underground metals mining operations to collect surface blast vibration data produced by heading blasts and stope blasts. The data included blast vibration amplitude values, seismograph records, blast design geometry, charge weights, and detonator delay and sequence designs. The total amount of information was used to produce a regression equation and summary dataset that could be used by the proposed underground mining operation to evaluate blast vibration amplitudes that will be generated on the surface. This work is published and presented so that operations with proposed underground mines or proposed underground mine extensions can use these equations to predict vibration amplitudes on the surface above the mine workings before any blasting occurs.

By Liu Hui Yang Nianhua Feng Shuyu

The paper analyzed the dynamic stress in the rock around the tunnel and the effect on the stress variation for the different blasting parameters. Also, the paper verified the theoretical results by dynamic photoelastical tests and provided helpful reference for the design of blasting near a tunnel.

Jan 1, 1998

By D K. Joyce

Large diameter boreholes have become increasingly popular in underground mining. Drilling equipment can drill full rings, including vertical upholes. Special techniques are required to load upholes of three inch to eight inch diameter. The current methods for loading AN/FO and bulk or packaged emulsions are described.

Jan 1, 1988

By Andrew Stirling

Quarry operators are under constant scrutiny by individual neighbors and neighborhood associations due to the environmental issues arising from daily quarry operations. Issues range from truck traffic, to dust, to blasting induced vibration and noise. Quarry operators and shot service providers employ best practices to minimize disturbances to neighbors. However, these efforts have been limited by the accuracy and flexibility of conventional initiating systems and design techniques.

Jan 1, 2002

By Mike Cammack

Western South Dakota is predominately an agricultural area, with exception of the mining and timber industries in the Black Hills region. With precipitation rates averaging below fifteen inches per year, water is a precious commodity to the livestock industry. There is a constant demand for the construction of earthen water storage facilities (dugouts) to catch snow and rain runoff, or developing natural springs.

Jan 1, 1993

By Tom Hanke, Joe Strobbe

The 80 year old Theodore Roosevelt Dam built in a scenic canyon near Globe, Arizona is currently undergoing a major renovation. The old stone dam, built by hundreds of skilled stonemasons, is being covered with a new concrete face that will increase the dam height by 77 feet. The renovated dam will improve flood control and provide increased electrical power and recreation area. The contractor, J.A. Jones is constructing the new dam and powerhouse for the Bureau of Reclamation.

Jan 1, 1993

By Michael Wieland

Three laboratory tests were developed for rating the wave-impact ruggedness of cap-sensitive explosives that are used for blasting in underground coal mines. Destructible pipe fixtures, called simulators, reproduce the shock wave or rift compression registered during the cross-hole wave interactions. The rift-compression fixture was modified to render quasi-static desensitization, when utilized with a remote air supply. Waves that were recorded near charge explosions show narrow pulses resembling underwater shock waves, followed by wide, weak humps, called rift compressions.

Jan 1, 1996

By Calvin J. Konya

There have been many different brands of high precision caps introduced on the US market in the last five years. High precision timing definitely effects the performance of the blast. One should be able to optimize fragmentation and minimize environmental effects with the use of high precision caps and selection of the proper time period. The consumer who purchases the caps may not be fully aware of the tolerances in firing times of caps used in the field. This paper will discuss results of field tests of cap tolerances from an independent study conducted by Precision Blasting Services.

Jan 1, 1989

By R C. Berglund

Since the Republic Mine began production in the mid 1950's, drilling and blasting practices have continually changed. In recent years, progress has been achieved through the development of more precise blast engineering methods, in greatly increasing the use of non-water resistant ammonium nitrate explosives, and in changing to a non-electric in-hole delay initiation system. Also, recent experience indicates that ammonium nitrate fueled with nitropropane and methanol is a viable substitute for aluminized AN-FO.

Jan 1, 1980

By Alastair Torrance, George Boucher, Roger Keller

An investigative blast programme has been carried out to provide information on the best blasting methods to excavate Chek Lap Kok island in Hong Kong for the new airport. The objectives of the programme included the assessment of a range of blast design parameters and their influence on fragmentation. This has been evaluated by physical assessment, photo digitising of the muckpile and computer predictions. In addition, a model to predict the three dimensional muckpile shape has been successfully calibrated.

Jan 1, 1992

By Janos Foldesi, Calvin J. Konya

The determination of the number of primers necessary to efficiently initiate an explosive column charge is essential to good blasting. If the number of primer is insufficient, the total energy stored in the main charge will not be released. On the other hand, the use of too many primers will be counterproductive and raise the blasting cost. Tests were conducted by the authors to determine the correct priming procedure for a basalt quarry. This paper describes the results of those tests.

Jan 1, 1976

By Zhang Qi

For the most part, the flying piece is serious endangerment in the demolition blasting. To prevent the endangerment, a large number of materials are needed as the protection. Therefore, the determination and design way of the flying distance of piece in demolition blasting have been concerned extensively. Previously, the experienced or half experienced formula was adopted to calculate the distance of the flying pieces. The calculating values of the distances of flying pieces are not identical with the practice results. The problems concerning the design way of flying distance of pieces are researched in the paper.

Jan 1, 1994

By J T. Patterson

The mining, quarrying and construction industries are often blamed for causing damage to residential-type structures when explosives are used. The claim experience for blasting vibration damage has been poor. This coverage is excluded from the Comprehensive General Liability (CGL) policy. To obtain this coverage, the policyholder must meet additional criteria and an additional premium must be paid. The risk management process offers the explosives user a technique for minimizing the risk of complaints and vibration damage claims on his insurance program and his cash flow. Case histories indicate that the vibration damage claims expense may be a lower risk than the risk of interference with production and cash flow. An annotated bibliography on risk management and defense of vibration damage claims is provided.

Jan 1, 1978

By Richard J. Mainiero, T S. Bajpayee

The Bureau of Mines, U.S. Department of the Interior, has developed test procedures and criteria for evaluating explosive reactivity of explosive contaminated solid waste substances generated by U.S. Army Ammunition Plants. These substances are produced as explosive-contaminated sludge from waste water treatment plants, residues from the burning of munitions and explosives on open ground, and residues from deactivation furnaces. The characterization of explosive reactivity is a prerequisite for disposal of such waste materials, which may be contaminated with primary explosives, propellants, or pyrotechnic materials. The Bureau has proposed two tests for this purpose. These tests were developed to evaluate the explosive reactivity as defined in Title 40, Code of Federal Regulations, Part 261.23(a)(6) and (7). These are Bureau of Mines Gap and Bureau of Mines Internal Ignition tests, which determine the sensitivity to shock and thermal stimuli, respectively. This paper also includes gap and internal ignition reference data for typical blasting agents, high explosives, propellants, and marginally reactive substances. These reference data were used to establish test criteria. The Bureau has evaluated over 400 samples of contaminated soil, sludge, and burning residues using these two test methods.

Jan 1, 1988

By Goran Cirkovic, Zvonimir Ester, Josip Krsnik

During the reconstruction of the motorway Zagreb-Krapina three reinforced concrete bridges were demolished, for their width was not adequate for the new motorway. Demolition of the three bridges was carried out by blasting as duration of the traffic cut on the motorway and the railway was limited to maximally 4 hours. During that period of time the demolished bridges had to be removed. Therefore, very tiny granulation was requested suitable for loading and not endangering the surrounding structures. Before each of three main blasting, trial blasting were carried out including the seismic measurements registering the seismic effects. The nearest residential building was at the distance of less than 30 m from the place of blasting. Additional difficulty was the fact that by each of the three bridges there is a new bridge, with minimal distance between the old and the new bridge being 30 cm. As each of the bridges is of different construction and of various thickness, particular blasting technique has been prepared for each one of the bridges.

Jan 1, 1997

By Calvin J. Konya

Backbreak behind the last row of boreholes can be a significant problem for blasting operations. Backbreak will interfere with the proper drilling and execution of the subsequent shot and can produce well defined boulders, which will not be broken by the subsequent shot. In order to determine the effect of timing on backbreak, a full scale blast with 6 1/2 inch boreholes was used to test the effects of timing. The test site was a quarry which had suffered from severe backbreak regardless of the blasting pattern or explosive used. One half of the production blast was loaded and initiated using the current technology at the quarry, the other half of the blast was deliberately timed in such a manner as to minimize backbreak. The timing was such to allow for ground movement in one row before the subsequent row fired. The test results proved that the amount of backbreak and flyrock could definitely be controlled with the selection of the proper borehole timing.

Jan 1, 1987