Search Documents

By Emily Johnson, Catherine Johnson, Ben Sonpon, Kelly Williams

The effect of length to diameter of the detonator is compared using Ansys/Autodyn 2-D simulations, the results of which are validated experimentally. It was found that higher pressure comes with a larger diameter, because it will result in more explosive energy being allocated out the end of the detonator.

Feb 1, 2020

By Robert Cefalo

Drill and Blast Engineer Abstract In 2019, the Bingham Canyon Mine, owned by Rio Tinto Kennecott Utah Copper Company, mined through the active underground that dewaters the pit. The active underground required the limitation of vibrations to avoid catastrophic damage or damage that would require work to the shotcrete and additional roof support. The surface design of the current sector next to and through portions of the active underground. The drill and blast group was required to test site law vibration parameters to ensure that vibration limitations were lower than limits set by the underground management team. Seismographs were used to validate the vibration prediction model and check performance of blast in areas of the underground. The bench conditions and limited pounds-per-delay created large obstacles for the blasting team, making it difficult for them to accurately load the pattern with the number of decks in the blast. Methods were used to improve the loading instructions and ensure that each hole achieved pound requirements based off of the distance to the underground that it was designed to protect. The project evolved from start to finish, and the process to estimate distances and loading improved to make the blast a more repeatable process for the size of the project.

By Leslie C. Taylor, Anthony L. Kee

Computational modeling of explosively loaded saturated sand on a suspended plate is an inherently complex problem. In this study a computational method is used to predict the dynamic pressure load/impulse from a buried charge. A fully coupled code modeling the explosive charge, sand and air with a Eulerian mesh and the plate structure with Lagrange elements, such as Gemini-Dyna, is an appropriate computational tool. In water-saturated sand, the loadings are soil and water-transmitted shock and bubble or blast effects depending on the depth and the charge size. The computations provide the capability to determine the total impulse load placed on a horizontal plate on or above the soil due to an explosion in the saturated sand for different burial depths in saturated sand and different plate stand off distances. The following test case will be presented: (a) 4.5 Kg (10 lbs) TNT, 10.16 cm (4 in) depth of burial to top of charge, and 20.32 cm (8 inch) stand off distance (Test 4).

Jan 1, 2005

By Amanda Verno, Danilo Coppe, Andrea Reggiani, Adolfo Bacci

The methodological example that comes from the demolition of the Genoa grain silos, should not been considered as an auto-celebration of a difficult project successfully executed, but should serve as an example of a new generation of demolitions where different technologies, often in competition, come together to obtain the optimal solution of a problem. Dynamite, diamond wire and hydraulic excavators overcame the most impressive building in town, working in very little spaces and on a geotechnically difficult site; moreover, a study on the dynamics and the effects of the impact of the structure, an analysis of the presence of potentially explosive dusts and an extensive vibrometric monitoring supported the design and the development of the operations.

Jan 1, 2005

By Stephen Mansfield

Analysing how accurately a blast design is implemented is one of the cornerstones of a successful operation, and critical for mine optimisation. This paper presents a concept that involves the collection and analysis of data for the five stages through which a blast transitions, from budget through to implementation.

Feb 1, 2020

By Benjamin Cebrian

Rock blasting at quarries represents multiple challenges not easy to see at first sight. Aggregate industries face similar or superior prices for explosives while extracting a material that usually is of less value of metal mining operations. Therefore, learning to optimize a quarry operation can be a perfect training for a position in blasting at larger metal mining operations.

Jan 1, 2010

By Muamer Medusalic, Kim Henley, Lucas Bottomley

The period from 2009 to 2012 has witnessed a large rise in the number of blast-generated fume events in Eastern Australia, where highly visible oxides of nitrogen (NOx) are produced from coal mine blasting. Fume production mechanisms have been poorly understood by mine operators, and practical measures to reduce fume were initially elusive. Over time, data on fume events has been collected and analysis has pointed to a range of contributing factors associated with fume production.

Jan 1, 2012

By Braden Lusk

This paper includes results from analysis of recorded Acoustic Responses of Structures to Blasting. The analysis was performed to determine specific characteristics of sounds experienced inside homes during blast events. Data was collected in a typical house within the Boone North No.2 Coal Surface Mine in Ashford, WV which was instrumented for several blast vibration and acoustic responses. The instrumentation consists of four acoustic microphones distributed throughout the internal areas of the house and three geophones buried near the house. Two additional channels collect the trigger signal and Air Blast information. For each blast event recorded by the system, the mine blast reports were used to obtain major blast characteristics such as distance from the blast to the instrumented house, weight of explosive used, number of boreholes, delays, and other important parameters. This information allowed study the relationship between the acoustic response and the blast design. From a database of 43 records, five records were chosen for complete analysis. These records were chosen based on distance from the blast to the house, and specific blast parameters. This paper presents the result of the relationship between the frequencies and amplitudes for the entire trace of acoustic records, the response due to ground vibration (GV), and the response due to air-blast (AB). Frequency content was obtained through Fast Fourier Transforms (FFT), using D-Plot software. The records have a typical shape that permits cutting and analyzing each part of the signal with respect to GV and AB separately. Some conclusions are reported concerning the relationship between blast parameters and acoustic response of structures.

Jan 1, 2009

By Alejandro Berrios, Matheus DaSilva, Erick Siqueira

Vazante mine is an underground polymetallic mine that produces zinc, lead, and silver, which belongs to Nexa Resources in Minas Gerais, Brazil. The mine, a sublevel stope underground mine, mainly applies two subvariants: VRM – Vertical Retreat Mining and Open Stope. In a specific place of the mine, the geology allowed the design of a production stope with larger dimensions than the standard stopes, commonly called Super Stope. At this place, the plan was to apply both sublevel variants simultaneously. This mining block comprises rings in two different levels, with access by two ore drives on each level; the dimensions would be approximately 50 meters high, 50 meters long, and 35 meters wide. Opening the Free Face to mine the whole Stope was a challenge due to operational issues, such as hazard risks from loading over void space, exposure to uncontained places, and the impossibility of implementing the optimal blast sequence. Wireless blasting initiators have gained popularity recently due to their convenience, safety, and efficiency. This initiation system was applied to preload all the rings required to open the Free Face, ensuring a safe and optimal blast sequence. Wireless initiation prevented hazard risks, enhanced the blast sequence to guarantee the required void space, and optimized the equipment's operational cycle. The blast crew carried out the activity without exposure to the risk of loading over void space. The wireless detonators also avoided after-blast activities, which were required to provide secure access to the blast crew, optimizing the operational cycle.

Jan 21, 2025

By P A. Lang, J G. Ayotte, R W. Humphries

Atomic Energy of Canada Limited (AECL) has the responsibility for research, and development of technologies, for the safe and permanent disposal of Canada's nuclear fuel wastes. As part of this comprehensive program, AECL is constructing an Underground Research Laboratory (URL) near Lac du Bonnet, Manitoba, to evaluate aspects of the concept of waste disposal deep in stable geological formations. No nuclear wastes will be used in the URL program.

Jan 1, 1986

By Christodoulos Xiouris, Ali Reza, James Karnesky

A rocket parachute signal flare is often used to signal a maritime emergency. In the general operation of these devices, a solid rocket motor propels a metal body to an altitude of approximately 1000 ft (305 m). At the end of the rocket motor, a propelling charge drives a signal flare and parachute out of the metal body and ignites the flare, which then burns for approximately 40 seconds as it falls to earth. In this paper, we describe an engineering investigation of an accidental ignition of a rocket parachute signal flare, which caused injury to the user. T

Feb 1, 2020

By M. K. Ameen, R. El-Hacha

This paper presents the analytical results obtained from numerical simulation of reinforced concrete slabs strengthened with various FRP systems and subjected to blast loading. A three-dimensional finite element model using AUTODYN software was used to predict the overall behavior of the slabs. The numerical results were validated by comparing with experimental results from a program carried out to investigate the efficiency of different strengthening systems on the blast resistance improvement of small-scale reinforced concrete (RC) slabs. The experimental program consisted of testing nine RC slabs strengthened with three different externally bonded (EB) FRP systems attached at the bottom side of the slabs and one RC slab tested without strengthening for comparison purposes. The EB FRP strengthening systems investigated included two layers of Carbon Fiber Reinforced Polymer (CFRP) sheets, two layers of Glass Fiber Reinforced Polymer (GFRP) sheets, and one layer of Glass-Fiber Resin Polymer (GRP) sheet. Different epoxy resin, patching mortars and impregnating epoxy adhesives were used for the slab surface preparation and FRP system application of the strengthening layers. The aim was to evaluate the residual strength of the test specimens after exposure to blast loads. The blast loading parameters were evaluated for each test using AUTODYN simulation and compared with the computer program CONWEP. All specimens were subjected to same spherical TNT charge weight and stand-off distance with the respect to the slab top surface. Extensive comparison is made between the experimental results and the AUTODYN simulations for the control unstrengthened slab and the strengthened slabs including time history records of the bottom steel strain and mid-span acceleration and the peak dynamic deflection of the slabs.

Jan 1, 2010

By Steven Putt

The paper presents new results from Datacloud during recent Seismic While Drilling trials in iron ore, metallurgical coal, and hard rock mines around the world. The measurements are compared with wireline geophysical logs, core data, drill cuttings, and conventional measurement while drilling (MWD) systems to validate the technology and show how the data can be used.

Feb 1, 2020

By Francisco Leite, Tomi Kouvonen, Bianca Saraiva, Vinicius Miranda, Auã Oliveira

One of the main challenges facing mining engineers is to draw up a plan that can be implemented in a timely manner, taking into account the operational variability of the mine’s production processes. These plans are often drawn up based on deterministic modelling (provided there are a set of known inputs that will result in a single set of outputs), when in truth we are talking about stochastic events (the cycles involved behave like random variables and their nature may be studied and reproduced). The result of using this kind of methodology can lead to non-optimized intuitive choices, which may harm the long-term targets defined by the planning team. Based on this principle, this document investigates the simulation of the rock fragmentation process in an open pit mine to assess the stochastic behavior of the loading and haulage operating cycles. The data assessed by the simulation process were the total costs of these operations in function of the powder factor. Based on a sample set data items, it was possible to check the probability distribution of the event as a Poisson distribution, applied to the loading and haulage cycles. The simulation consists of the repeated sequenced reproduction of these events (Monte Carlo simulation), in order to find the configuration that best fits the loading and haulage operations. By integrating these systems, it was possible to better understand the influence of the blasting in these operations, and as such to reduce the associated costs.

Feb 6, 2023

By Riaan Van Wyk, Gys Landman

In today’s mining environment the use of radio communications in the form of two-way radios, cellular phones and even automated mining, form a vital part of the daily operations of a mining site. The radio transmissions that are used are a form of energy and as with all other types of energy it can have an influence on blasting equipment.

Jan 1, 2011

By Rakesh Raghavaraju, Bibhu Mohanty

The paper analyzes the decay of shock pressure as a function of distance from the borehole, and its implication on shock-induced fracture properties of the target rock as the first step in predicting fracture and fragmentation behaviour in a well-characterized rock.

Feb 1, 2020

By A. Gontijo, A. Matos, P. Lincoln, L. Fonsecail

This paper investigates how to manage and model the vibrations caused by rock blasting in a Brazilian underground mine. Considering the frequent detonations and the previous lack of effective vibration control, understanding, and reducing the impact of these seismic waves is critical. We emphasize the use of the near field model technique, which considers the varied physical properties of different rocks, optimizes blasting plans, and minimizes damage to the rock mass. We detail a case study that demonstrates a comprehensive approach to vibration control. The discussion includes the creation of a monitoring plan, the methodology used, results and the specific challenges and solutions found during the blasting process. This study provides a practical guide for similar future projects. Finally, we present a predictive model based on the collected data, offering insights into the vibrations caused by blasting. This model helps decision-makers minimize the risk of displacing rock blocks in the blasting area, improving safety and operational efficiency

Jan 1, 2024

By Enver Alan

In this study of applied explosives engineering the blasting applications are evaluated, which were carried out for research and development purposes at Yenisahra Station tunnels in Kartal Formation which was built with the aim of solving İstanbul's transportation problem within the framework of the Kadıköy-Kartal Metro Project. Twenty-four shots were made by using explosives in 60 blastholes that were drilled in the tunnel faces, which were located between and outside of two different faults. S

Feb 1, 2020

By Guo Ziqing, Tang Qiuming, Liu Yuanyuan

The channel-type non-mechanical stirring production process is a new developed technology for emulsion explosives in recent years. It removes traditional equipment such as mechanical-mixing emulsification, mechanical-mixing sensitization, matrix pumping, and explosive pumping, and has been applied in China. This technique achieves a fusion of higher intrinsic safety and lower cost, as well as the excellent quality of products and high efficiency of production. The emulsion particle diameter is about 0.5μm. The storage period of emulsion explosive produced with span-80 emulsifier is more than 7 months.

Jan 21, 2025

By Francisco Sena Leite, Vinicius Miranda

Mine blasting is directly associated with ground vibration. If these affect critical structures (buildings pit walls, etc.) they must be mitigated to reduce the environment and social impacts. Vibration monitoring and control is one of the most important procedures in blasting because it will impact short and long term incidents associated with this blast effect. Technology moves ever forward, and today we have personal devices that are equipped with an array of sensors, for that reason the authors decided to investigate the possibility of using a personal device to do vibration control. This case study compares the same blast measured with a traditional seismograph and a smartphone. To validate this new methodology, attenuation laws were built with data from a traditional seismograph and a smartphone application. Predictions were also made prior to a set of blasts. Residual analysis was used for data validation from the two different sources. From the performed analysis, to prove the validity of this new methodology, the normality tests for statistics residues analysis proves that it is possible to infer that the model has a null residual mean and a small residual error. The achieved results show the accuracy of these devices, the authors pretend to show the potential of this equipment and open a completely new door for vibration analysis.

Jan 1, 2018