Search Documents

By D. Johann, E. Zanetti, I. A. S. Brum, P. M. Zancan, A. F. Castro

"This study was done from a sample of coal mined at the Vale-Mozambique mine, located in Moatize district, Tete Province. The aim of this work is to analyze the reagent system in the flotation of coal fines belonging to the Upper Chipanga layer (UC). Among coal processing methods, flotation stands out as one of the most important for the concentration of this material, in particular in the treatment of fine particles. The total feed of the Vale-Mozambique processing plant is 8,000 tph of coal, where 10% of this feed corresponds to the fine fraction that feeds the flotation circuit. The material used in this study had a particle size of 96% smaller than 0.25 mm. The reagents used in the flotation tests were betacol and diesel oil as hydrophobizing agents and MIBC as frother. The range of betacol concentrations in the first test phase was 200 g/t to 500 g/t, and in the second phase 200g /t to 500g /t while diesel oil and MIBC were kept constant at 300 g/t. The immediate analysis followed the Brazilian standards NBR 8289, NBR 8293, NBR 8290; and NBR 8299. The results showed that it is possible, from a feed with ash content around 22.84%, to obtain products with levels below of 10% ash, with a mass recovery around 50%. The recovery of carbonaceous matter was also evaluated and presented positive results. Complementing this study, the effect of H2O recovery was evaluated and it was observed that for the concentrations of betacol the recoveries ranged from 6 to 9%, and for diesel oil plus MIBC were 4 to 7%.INTRODUCTION Considering the increase in population and energy consumption as humanity has been living along the last decades and the consequent demand for non-renewable natural resources, it is clear the challenge of the mineral industry in the search for new technologies and improvement of the existing ones. This challenge is justified by the need for better industrial results and to meet the market specifications, taking into account the reduction of deposits with higher contents and the need for beneficiation of more complex ores, lower levels and lower release granulometry. Usually in these situations, processes already well-established as the gravimetric (Sampaio and Tavares, 2005) have not good results."

Jan 1, 2018

By Song Z. Guo

Calcite and magnesite are both carbonate minerals and their crystals belong to trigonal system. Flotation tests were carried out to investigate the flotation behaviors of calcite and magnesite. The test results show that the floatability of calcite and magnesite under different grinding environment had obvious differences. The floatability of calcite using sodium oleate as collector after dry grinding is better than wet grinding, but the floatability of magnesite after wet grinding is better than dry grinding. The XPS surface elements test and zeta potential measurement show that, wet and dry grinding process makes the distribution difference of surface anion and metal cation, then influence the floatability of the two carbonate minerals using sodium oleate as collector. Difference of the carbonate crystal structure and solubility properties was also investigated. Research shows that crystal structure difference of calcite and magnesite causes the difference of solubility, which can influence the flotation behaviors under different grinding environment. Keywords: carbonate mineral, crystal structure, solubility properties, flotation, surface character

Sep 1, 2012

By Deirdre Bradshaw, Cornelius Vos

"The detailed understanding of the variability in process performance parameters within an ore body forms a key aspect of ensuring that proper decisions are made with regards to the economic viability of that ore body. To gain this understanding, various tools have been developed over the years, of which the batch flotation test is the most well-known and applied technique for investigating the flotation separation of ores. In this paper, the Julius Kruttschnitt Mineral Separability Indicator (JKMSI) is put forward as a small-scale test, suitable for the characterization of the flotation separability of copper porphyry ores. It is demonstrated that the JKMSI can be a complementary technique to the batch flotation test, with the capability to further improve the knowledge of ore body variability. The response from this test has been shown to be sensitive to particle size and modal mineralogy, providing a critical link between flotation and upstream comminution activities. The trade-off between the fineness of grind and the recovery target can thus be evaluated to determine the minimum energy application required for optimal separation economics. The test is designed to utilize small sample quantities of various sizes, providing an opportunity to increase our understanding of ore variability through increased tests. This complements our ore body knowledge and combining this with efforts in comminution (Powell, 2013) provides a platform for extending the concept of flexible circuit design."

Jan 1, 2014

By Yuliy Rubinstein

"The paper presents a analysis of the history and the trends of development of flotation apparatus. The laws of their evolution are stated and the place and role of column flotation are indicated. It is demonstrate development and different design of column apparatus. The major parameters of column cell such as diameter and height are discussed. Options are proposed on optimization of hydrodynamic characteristics of columns with large-capacity cells. High efficiency of columns with cell height of 4-6 m is shown on examples of coal preparation. A new generation of multi sectional column cells has been developed. In the cells are zones with different aerohydrodynamic parameters: combined in the machine are co-and counter- counter flows of phases. The transition from single-chamber column to multi-sectional apparatus makes it possible to create favourable hydrodynamic and aeration regimes in each section of the column dependent on the pattern of material distribution by floatability. Efficiency of application different designs column apparatus uses shown on the example of enrichment of various non-ferrous metals ores and coal. The principles of mathematical simulation of the flotation process are developed. A scaling-up procedure for column cells was based on flotation macro- and micro- dynamics simulation.INTRODUCTIONColumn flotation is considered to be one of the most significant achievement in the field of mineral processing in the end of last century. We cannot but agree with this statement but would like to understand what underlies this success. History of the flotation column can not be considered in isolation from the development of flotation apparatus on the whole. It can be argued that the first attempt to switch from oil flotation to the use of bubbles during flotation was performed Bessel brothers in 1877 (Berlin patent 42 class 22, July 2) and in 1886 (Berlin patent 39,369 May 12). According to these patents, the crushed ore was mixed with oils , hydrocarbons and water. Then the pulp received in this way was heated up to boiling . Air bubbles and steam formed during boiling facilitate the flotation of ore particles coated with oil (first patent) or bubbles been generated by the reaction of lime with acid (second patent). The evolution in the design of the flotation apparatus incorporates the following key stages. Further development is connected with the Francis Elmore’s idea to use gas bubbles received at water electrolysis (UK, 13578; 1904). This method was not introduced then, but much later, in our time and on the essentially new technical basis it found a use for sewage treatment (electroflotation). Gas bubbling under vacuum patented also by Elmore (UK, 17816; 1904) obtained a practical use. It should be noted that the method did not lose its importance till now. The design of the camera has been surely optimized (Glembotskii etal, 1963). A year later A. Macquisten (UK, 26712) developed pressure (compression) flotation. Thus, the H.Sulman, H.Picard, D. Bell’s (US, 853120, May 29, 1905) basic patent and the adjoining T. Goover’s patent 1910 (US, 953746) formed the basis of the first and most important element of modern flotation: flotation with air bubbles sucked in from the environment. In 1914, J.Callow received a patent for on an apparatus where air was sparged through the porous false bottom of the cell ( US, 1104755). Woolen fabric folded four times was fixed on a perforated metal frame to be used for air sparging (Gaudin, 1932). The following year Durrel created the prototype of the injection (ejector) apparatus. The jet aerator made it possible to significantly reduce the size of the bubbles, in comparison with the filter cloth. An apparatus with slurry pre-aeration in an airlift prior to feeding into separation cell was developed Wagner in 1917 (US, 1235083). And finally, the first column apparatus with a counter-current of slurry and air was developed by M. Towne and S. Flynn in 1919(US, 1,295,817). ("

Jan 1, 2018

The reactivity of clay minerals and variety of these reactions are greater than any other known colloidal material. While it is acknowledged that clay minerals can cause problems in mineral flotation, the literature contains conflicting evidence, particularly with respect to the effect of clays on froth stability. It is well known that achieving and maintaining optimum froth stability is an influential factor in determining froth flotation performance. However, the presence of clay minerals in the ore is a major challenge to obtaining a stable froth. In fact, clay minerals could reduce froth flotation performance by both decreasing and increasing froth stability. The mechanism by which clay minerals affect froth stability is not fully understood and needs to be investigated further. In order to improve flotation performance, reliable knowledge of the effect of clay minerals on froth stability is essential which is discussed in this paper. Keywords: froth flotation, froth stability, clay, clay minerals

Sep 1, 2012

By V. A. Ivanova, T. N. Perunkova, N. O. Dorozhanova, G. V. Mitrofanova

"Oxyethylated compounds are used as reagents-regulators in the flotation of non-sulfide ores, in particular, apatite-containing ores. Thus, the necessary degree of selectivity in the flotation separation of two calcium-containing minerals of apatite and calcite is achieved only by using, in addition to a collector, regulators-reagents from the nonylphenol ethoxylates class. In order to establish the most optimal structures, this paper presents a comparative assessment of the physical-chemical and flotation properties of several classes of oxyethylated compounds - alkylphenol ethoxylates, aliphatic alcohol ethoxylates and oxyethylated carboxylic acid. The authors have studied their dispergating ability with respect to the air phase and calcium soaps of the carboxylic collector. Dependences of foaming properties of regulators on the degree of oxyethylation have been determined. Adsorption isotherms of sodium oleate on apatite and calcite in the presence of regulators have been obtained. It has been shown that the presence of oxyethylated compounds in the solution reduces the amount of the adsorbed fatty acid collector. The influence of the considered classes of regulators on apatite flotation has been studied. The interrelation of flotation properties of oxyethylated compounds and their molecular structure has been established.INTRODUCTION Flotation plays a leading role in complex apatite-containing ores processing. However, two calcium-containing minerals - apatite and calcite, which compose apatite-carbonate ores, are characterized by close flotation properties. Selective separation of these minerals is a difficult task, the solution of which is impossible without using reagents-regulators. One of the ways to ensure the selectivity of the flotation separation of calcium-containing minerals is the use of reagents-depressants such as sodium silicate, starch, cellulose derivatives, and others (Liu et al., 2016; Rao et al., 1989). Another method is the application of nonionic reagent regulators (Filippov et al., 2016; Filippova et al., 2014; Ignatkina, 2017), which contribute to the adsorption of the ion collector (Filippov and Filipova, 2006 Rao and Forssberg, 1997) and stability of formed froth (Sis and Chander, 2003)."

Jan 1, 2018

By T. Shumba

The solvent extraction section of an old Uranium Plant in the Vaal River region produced a sub-stance called Crud (Chalk River Unidentified Deposit) that formed within the aqueous/organic interface of the settler of the solvent extraction circuit. The crud was deposited together with gold tailings to the tailings dam many years ago. Previous research done on the crud confirmed that ex-posed crud leaches Mn and Ni at concentrations that are well above their acceptable risk limits as well as Zn that leaches at concentrations that are slightly lower than its acceptable risk limit. Soil washing and bioremediation technologies were employed to treat the contaminated soil. Various laboratory test work and the pilot scale studies were conducted in parallel with each other and the results of the laboratory studies were used to determine critical parameters. Four lixiviants, i.e. sulphuric acid, acetic acid, oxalic acid and ethylene diamine acetic acid were tested at three concentration levels i.e. 0.001M, 0.0001M and 0.00001M, respectively. Column tests showed that the leaching of the heavy metals increases as the soil porosity increases. Silica sand was added to increase porosity of the contaminated soil. Highest Mn removal was achieved mainly by sulphuric and oxalic acid at 0.001M at all soil levels. EDTA was significantly efficient in the removal of Ni and Zn. The recovery of heavy metals, particularly Mn, decreased as the depth of sampling in-creased. Heterogeneous bacteria and filamentous organism plate counts were conducted to evaluate the growth of the bacteria and filamentous organisms in the soil. Results showed that more organism growth took place in the bioremediated soil with a fertilizer added to it. The leaching of metals from the soil that was bioremediated in the pilot study was generally higher than the extraction of the metals from the soil that was leached with no bioremediation carried out. The results from this study suggest that the leaching of heavy metals from the contaminated soil is to a large extent dependant on the pH of the leaching solution. By increasing the soil?s porosity and bioremediating the soil, higher extractions of metals were achieved.

Jan 1, 2014

By M. Saba

In cyanide leaching procedure, achieving an acceptable efficiency for silver and gold is very time-consuming, thus, enough studies have not been performed for optimization and modeling of this process. The kinetics of cyanide leaching includes two steps: first step comprises a sharp slope while the other has a slight increasing trend. In the present study, in order to reduce the time and cost, the cyanide leaching process of a sulfide silver/gold ore was optimized in the first period. The applied parameters and their ranges are: temperature 20-40 (°C); time 1-8 (hrs); cyanide concentration 1-2 (mole cyanide / mole Cu); the percentage of solid to liquid 1-2 (%) and pH 10-12. For design of experiments fractional factorial 2(5-1) was used. Also four center points were applied to increase the accuracy of the model. In addition, by analysis of variance (ANOVA) the most effective parameters were identified and the optimized condition was determined. A regression model was proposed to describe the effects of independent variables and their interacting role on silver recovery. Results showed that the model was linear for silver and nonlinear for gold. In the gold recovery process, the two important parameters are time and pH with the former being more effective. Due to the existence of cyanide ions in the medium, temperature and cyanide concentration have less influence in the gold recovery process. Solid to liquid ratio, in addition, comprises a slight negative impact on the procedure. This emphasizes the different kinetics of silver/ gold cyanide leaching. Finally, using the optimum condition the amount of silver and gold obtained were 61% and 67% in 8 hours, respectively. While in general conditions, the results were 37% and 54% in 24 hours, respectively. Keywords: cyanide leaching, refractory gold/silver ore, modeling, optimization

Sep 1, 2012

By S. J. Liu

The conventional collector for bauxite mineral is oleic acid, which is highly insoluble and must be used in high dosage in bauxite flotation operations, that is the great drawback of oleic acid in use. A series of hydroxamic acid were synthesized, and their collecting ability to certain minerals in bauxite: diaspore, kaolinite were studied. The collecting power of various reagents to diaspore in an incremental sequence were shown as follows: benzyl hydroxamic acid<amylic hydroxamic ac-id<heptylic hydroxamic acid<oleic acid<octylic hydroxamic acid; while the incremental sequence of the collecting power to kaolinite was like this: benzyl hydroxamic acid<amylic hydroxamic ac-id<heptylic hydroxamic acid<octylic hydroxamic acid<oleic acid. It could be seen that octylic hydroxamic acid had the capability of high collectivity and good selectivity, and octylic hydroxamic acid was chosen to use in the following experiments. Reduced zeta potential showed the adsorption of the anionic collector on the mineral. By the adsorptive capability and IR tests, the adsorption of octylic hydroxamic acid on diaspore was determined to be chemical absorption, which was greater than that of oleic acid, as it was physical absorption. Results of floatation experiments on manually mixed minerals indicated that the collectivity and selectivity of octylic hydroxamic acid were better than oleic acid.

Jan 1, 2014

By S. L. Gubin, T. V. Ignatova, A. V. Levshin, D. O. Sharkovsky

"Flotation process applied for concentration of unoxidized ferruginous quartzites by PJSC Mikhailovsky GOK (MGOK) is based on wet magnetic separation of strong magnetic minerals. However quality of the resulting concentrate (Fe65-66%) is insufficient for production of metallics. Quality upgrade of magnetite concentrate via flotation has been implemented by MGOK to produce premium quality magnetite concentrate.Flotation is a challenging process due to sensitivity to varied amounts of reagents, fine and coarse mineral ratio, particle contact (retention) time and temperature of feed. Tomah’s PA-14 reagent (USA) has proven efficient for application in flotation of MGOK’s magnetite concentrate.Objective of this work is to select and prove applicability of selective agents for flotation upgrade of magnetite iron ore concentrate.Series of flotation tests has been carried out with application of new highly selective collecting agents produced by Akzo Nobel (Sweden), Clariant (Germany) as well as Akzo Nobel’s and Tomah’s cationic collector mix to improve performance efficiency of flotation process. Tomah’s flotation agents and Akzo Nobel’s Lilaflotproved to be the most effective for purposes of concentrate quality upgrade to Fe69.0% via flotation.Testing Method: Following scientific research methods were applied for testwork: system analysis, mathematical statistics, observation, comparison, trial (experiment).To determine key process factors a series of pilot tests was carried out. Most of the testwork was performed by PJSC Mikhailovsky GOK’s Central Process Laboratory.Work Results:-optimized flotation performance modes were defined to ensure production of three types of low-silica concentrate, i.e. containing SiO25%, SiO24% and below SiO23% by weight. Most efficient selective agents applicable for flotation have been defined. Mixture of higher aliphatic amines has proven to intensify selective flotation of quartz. It enables higher yield of chamber product maintaining desired quality of concentrate.Achieved process operation and performance factors have been revaluated.Value for Advancement and Expansion of Mineral Processing:Flotation of concentrate has enabled expansion of PJSC Mikhailovsky GOK’s production capacity, improved production quality, helped to maintain sustainability and competitive advantage of the company."

Jan 1, 2018

By S. H. He

This paper focuses on the influence of pulp oxygen content on the separation of pentlandite and pyrrhotite contained in two different process streams in the Clarabelle Mill, operated by VALE INCO. The two process streams are (i) the scavenger cleaner feed, the product of regrinding the thickened, scavenged concentrate and the B cleaned tail produced from treating the non-magnetic fraction of the milled run of mine ore, and (ii) the magnetic concentrate which is the magnetic fraction of the milled run of mine ore. In the Clarabelle Mill, sulphite (SO32-) and TETA (triethylenete-tramine) are together used to selectively depress pyrrhotite from pentlandite. These depressants pre-ferentially decompose collector and/or sulphur enriched species at the pyrrhotite surface, an appar-ently essential mechanism in pyrrhotite depression from the scavenger cleaner feed stream. Selectivity in depression may originate from differences in the electrochemical rest potential of pyrrhotite and pentlandite. As both minerals are susceptible to oxidation, aeration in conditioning and flotation plays a key role in selective flotation. Important differences in the flotation behavior of pentlandite and pyrrhotite from the magnetic concentrate and the scavenger cleaner streams are highlighted in

Jan 1, 2014

By G. H. Lind

The Minerals Tertiary Education Council (MTEC), over the past decade, has worked closely with Australian higher education partners in metallurgical education to build capacity in this discipline to deliver high quality graduates for the Australian minerals-industry. This paper explores the benefits of industry engagement through a national innovative collaboration, the Metallurgical Education Partnership (MEP), and specifically the final year Process Design Project (PDP), over the four year period from 2008-2011. Some of the benefits discussed in this paper include outcomes of the student experience during an industry-intensive workshop, collaboration between higher education providers and aligning graduate attributes to meet industry requirements.

Sep 1, 2012

By S. V. Petrov

In recent years, heap leaching of gold is becoming wide spread due to low capital and operational costs that allows economically feasible processing of low-grade and cut-off grade ores. Currently, over 30 heap leach projects are operated in Russia. Some of the deposits treated by heap leach methods are almost depleted. Therefore, they will soon require spent heaps detoxification and reclamation. Traditionally, spent heaps are detoxified by chemical treatment. This process is characterized by relatively high kinetics and requires expensive reagents and additional equipment. The main disadvantage of this process is secondary contamination of the solutions by products of detoxification reactions and impurities contained in reagents. If there is enough time, spent heaps can be detoxified by natural degradation. The advantages of the proposed method are low operational costs due to use of existing heap leaching facilities and eliminating the need for chemicals for spent heaps detoxification. Residual concentrations of cyanides and thyocyanates in liquid phase (wet ore) of spent gold ore heaps after detoxification were 0.2~0.3 mg/L. Heavy metals were almost completely removed. The method was successfully used for detoxification of spent heaps at two gold mines.

Jan 1, 2014

By I. Kairyakov

The present paper is about the restoration of the molybdenum production in the floatation plant of Ellatzite-Med AD in Bulgaria. The process, based on a working design, includes the construction of a new floatation molybdenum section in the existing molybdenum department of the Floatation Plant using the so called Vemco inert-gas floatation machines, made especially for the molybdenum floatation. While in the ordinary floatation machines, block impellers create suspension of the air, sucked from the atmosphere with the slime particles of the concentrate, which creates conditions for oxidizing the reagent, Vemco inert-gas floatation machines are covered with hermetic lids and the air inside the chamber is used. The technology, suggested by Geotechkoper Ltd. for making the working project, employs special machines from Dor Olliver Aimco, suitable specifically for molybdenum floatation in order to reduce the oxidizing of the reagent sodium hydrosulphate. Also the transport of the chamber product is done in hermetic conditions as the molybdenum flotation is done in two floatation rows and refining operations 3 to 8 are placed in the second row. Thus in the basic molybdenum floatation together with the first and second refining operations, which are hermetically closed, an ambient condition with low content of oxygen is created, that is about 8% for oxygen and about 92% of nitrogen, in which the oxidizing process is extremely reduced. This in turn results in reducing the consumption of the reagent depressor ? sodium hydrosulphate. In that way there is an improvement of the economical indices of the molybdenum production.

Jan 1, 2014

By A. Gülmez

The complex ore deposit containing fluorite, barite and bastnaesite minerals is located in Beylikova Region of Sivrihisar town of Eskisehir Province of Turkey. The ore contains 40.80% CaF2; 35.35% BaSO4; 2.01%Ce; 1.5% La; 0.39% Nd and 0.1% Th. Barite recovery from this ore by flotation of the HCl leached tailings is presented in this paper. Rare earths are recovered by leaching. The leached residue (tailings) containing fluorite and barite is subjected to froth flotation to recover barite. The effect of pH and collector concentration on the flotation of barite have been studied in this work.

Sep 1, 2012

By D. Gucbilmez

Three spiral concentrators having different geometries were compared in a chromite processing plant. They had different diameters, helix-cross sections and capacities. Two of the spiral concentrators were manufactured in China and one of them was manufactured in Australia. The tests were carried out in a closed circuit experimental setup by using a low grade chromite ore. The pulp densities kept the same during the operation, and the samples were taken simultaneously. The effects of the different positions of the splitters on separation and the feed rate were the parameters that were observed during the experiments. The performances of three spiral concentrators were found to be different. To clarify the effect of the particle size on the separation in spiral concentrators, the screening was applied to the feed. The samples were sieved from 75µm. The test results indicated that the separation performance decreased dramatically in very fine particles. Although fine particles caused some problems in spiral concentrators, fine grinding is required for this particular chromite ore for better liberation. A suitable method for the fine particles should be investigated for acceptable recovery.

Sep 1, 2012

By G. K. Palshikar

Mining operations offer many opportunities for the use of IT and communication technologies to improve automation and thereby deliver higher levels of productivity, cost, quality and safety. In this paper, we discuss a particular application, namely, building a fully automated train control and operation system within a mining area. We first outline the basic architecture and functionality of such a system and then present a real-life case study where the railway system within a remote iron ore mine in Canada was converted to a fully automated train operation system. This hard real-time safety-critical system required the use of advanced technologies such as embedded systems (e.g., on-board train controller), radio communications, formal methods, optimal scheduling, and extensive simulations. We focus on the design aspects for maintaining the system in safe states.

Sep 1, 2012

By A. Bahrami

Andalusite, silimanite and kyanite are polymorphs of aluminosilicate known as kyanite group. Minerals of this group are used in refractory. Sarband andalusite deposit is located in Markazi province in Iran. Mineralogical studies showed that the main minerals of this sample are andalusite (5%~10 %), mica, quartz and feldspar. Processing of the samples was carried out using two sizes, i.e. +500 µm and -500 µm. In the processing of +500 µm scrabble test was carried out on -4750 +500 µm and -2380 +500 µm. For -500+300 µm shaking table and magnetic separation were applied. For -300 µm fraction, flotation was carried out. The results of this tests showed that the processing of Shazand andalusite was not possible, because silica and iron impurities were diffused inside the andalusite mineral grains.

Jan 1, 2014

By P. K. Fedotov

At projecting mining-concentrating complex at the deposit ?Zapadnoye? (Russia) it was considered to enable an opportunity of refusal from conventional SAG-mills. First time a scheme of gold bearing ore destruction using Roller Press RP 5-100/90 had been developed and integrated. The plant was launched in summer 2003 and presently it has achieved designed technological parameters, processing throughput comes to 1 million tons of the ore per year.

Jan 1, 2014

By E. Guerrini, M. Maccagni, J. Nielsen

"Lead is the most important material able to meet the current demand for energy storage. The lead acid battery is reliable, efficient and inexpensive. Continuous developments in battery construction are providing improvements in all aspects of the batteries’ performance. The lead acid battery is both the main lead product and the main raw material for lead production. More than half of the lead produced is from secondary smelters where batteries are the most important feed material. The environmental pressure on lead production has been increasing for many years, and continues to become stronger and stronger. The lead production processes and technologies themselves will require updating to meet the new regulations. Although they are very strict now, they will become even more so and current technologies may not be sufficient. Because recyclability is a strong point for the lead acid battery, the secondary smelters need to reduce the environmental impact as much as possible. In recent years, the secondary smelters underwent impressive changes in this direction, but some more improvements are possible. Electrochemistry can offer a step change improvement in making secondary lead production more environmentally friendly. Engitec has developed an electrochemical process base on a very high current density (high productivity) cell using an inexpensive electrolyte and at a relatively low cost. In this paper, the latest update on the technology is provided. INTRODUCTION The lead acid battery is considered the “walking dead” by some new technologies trying to replace it. It has played and will continue to play a very important role in our lives because it is inexpensive, fully recyclable and the existing lead and the mine reserves guaranty enough material for the extended future. According to the life cycle, the lead acid battery is the cheapest and the most effective system to store energy. Lead is practically a close loop where lead battery production consumes more than 80 % of the produced lead but contemporarily it is the most important raw material for the production of metallic lead. In fact, nowadays, the secondary production has overcome primary production and this trend is expected to continue. Primary lead is the make-up material for the existing battery production and the source of lead for the construction of the new ones."

Jan 1, 2018