Search Documents

By K. Vanstaen, K. M. Cooper, S. Ware, S. L. Boyd

Remediation and restoration of offshore marine habitats is a relatively new concept with attempts in European regions largely being instigated by requirements of various strategic directives including Article 2 of the Habitats Directive (1992), the EC Water Framework Directive (2000, Article 2 of the OSPAR Convention (1992) and the developing European Marine Strategy Directive. A field experiment to establish the practicality of various options for rehabilitating the seabed on the cessation of dredging has been successfully set up. The purpose of this experiment is to investigate the practicality and effectiveness of gravel seeding as a potential restorative method that can be applied at marine aggregate extraction sites following cessation of dredging. Zone 2, within Area 408 (offshore Humber) was chosen as the experimental site as there is some evidence for persistence of sand which may have resulted from screening operations at this site.

By Robert G. Ditchburn

Dating seafloor mineralization at hydrothermal centres of submarine arc volcanoes is important for understanding deep-seated volcanic events that can produce deposits rich in base and precious metals. The activity ratios, 228Th/228Ra, 228Ra/226Ra (Bq.Bq-1) and 226Ra/Ba values (Bq.g-1) are used for dating barite- rich seafloor massive sulphide (SMS) in the age ranges 0.3 ? 12 years, 3 ? 35 years and 500 ? 15,000 years, respectively. Thus, the time elapsed to amass an economic deposit and, ultimately, its capacity for sustainable extraction, can be estimated. 226Ra/Ba and 228Ra/226Ra values have been measured in relatively young chimneys that were collected, 1998 to 2006, from hydrothermal sites at Brothers and Clark volcanoes (Kermadec arc) and East Diamante volcano (Mariana arc) to check these initial ratios, essential for calculating ages for older mineralization at the same sites, were not varying significantly. We found that the 226Ra/Ba value for fresh SMS mineralization at the Brothers NW caldera and East Diamante hydrothermal sites have been reasonably stable for 6 years and 2 years, respectively. At both sites, the 228Ra/226Ra value for fresh SMS has been stable for 5 years. This was established from young chimneys where the measured 228Ra/226Ra value could be corrected for radioactive decay using the age derived via the 228Th/228Ra method. However, long-term stability of the initial 226Ra/Ba and 228Ra/226Ra values has yet to be proven. These isotopes of Ra are used as a proxy for better understanding of the transfer of Ba from deep magmas to the seafloor, via the circulating fluids of the hydrothermal system.

Jan 1, 2011

By Tim J. Boyd

Gregg Marine, Inc. (headquartered in Signal Hill, California) has recently introduced an innovative seafloor drill system for offshore geotechnical site investigation and seafloor mineral exploration. The system is capable of working in water depths of up to 3,000 meters and is rated to drill to a depth of approximately 150 meters below mudline. The remote operated system integrates established drilling technology with proven Schilling telemetry and controls. The flexible nature of the patented wireline drilling technology enables the use of standard sampling systems (up to PQ-size core and 3? thin-walled tubes) as well as downhole testing systems (including CPT testing, vane shear testing, downhole sensors and borehole geophysical tools). The modular nature of the seabed drill system and the accompanying launch and recovery system (LARS) enables the use of local vessels of opportunity for projects resulting in reduced project costs and improved mobilization responsiveness times. Keywords: seafloor, seabed, geotechnical, drill, drilling, core, coring, sampling, CPT, cone penetration testing, borehole, logging, survey, exploration, ROV, remote sensing

Jan 1, 2011

A C-CORE study on behalf of the government of Newfoundland identified the inner continental shelf off northeast Newfoundland as having a relatively higher potential for hosting placer gold than other parts of the inner shelf. Under the auspices of the Canada-Newfoundland Cooperation Agreement on Mineral Development, the Geological Survey of Canada conducted a three-year project to map the distribution of surficial sediments and the abundance of placer minerals (particularly gold) from White Bay to Cape Freels. Much of the study area is a fjord coast, with steep rocky slopes and scattered gravel beaches. The extreme east, from Hamilton Sound to Cape Freels, has a wide, shallow inner shelf, sandy beaches, and extensive coastal dunes. Relative sea level was high in the late glacial period. It has fallen continuously in the west, but in the east it dropped to -19 m, before rising to within several metres of the present level by 3 ka. In terms of surficial sediments and processes, five zones are identified: (1) Deep offshore deep basins that contain thick postglacial mud overlying glacialmarine gravelly sandy mud. This zone is below a depth of 370 m in White Bay, 300 m in the Notre Dame Basin. 2) Basin transition zone in which the sea bed has been eroded by currents, so that glacialmarine sediments are exposed in places. Winnowing has formed an uppermost layer of muddy gravel. There is a slight potential for enhanced levels of fine particulate gold, but the gold would not be exploitable. (3) Iceberg impacted zone Above 200 m the keels of icebergs impact the sea bed, causing furrowing and pitting. Furrows predominate in deeper areas, and pits are concentrated at the inner boundary of this zone. Iceberg turbates have developed in shallow waters (60-100 m). Combined with winnowing, iceberg turbation could enhance the potential for concentration of fine particulate gold, but not into economic quantities. 4) Wave dominated zone Above approximately 60 m the sea-bed sediments are highly mobile due to waves, currents, and iceberg impact. Sand is either rippled or organised into sand waves. Gravel is either poorly sorted, and organised into

Jan 1, 1995

By Pia-Maria Haselberger, Marc Schiemann, Christian Frühling, Nicolas Richter, Hendrik Wehner, Andreas Kaschube

"The paper provides the principle considerations for a novel vehicle class within the scope of the project Large Modifiable Underwater Mothership (MUM). The main idea for these ships is to create a highly modular building block system for the global layout. This building block system allows for a mission-dependent module assembly. For the purpose of deep sea mining for example, the range of tasks reaches from multipurpose transportation and exploration missions to supporting tasks in up to 5000 m depth, e.g. energy supply. Topics covered in this paper are related to potential missions for these vehicles, the modular layout and the structural layout of a separate block module. The paper closes with a conceptual design example for this class.Index Terms—MUM, UUV, underwater mother ship, autonomous underwater vehicle, modular, deep sea, conceptual designI. INTRODUCTIONAs one of the leading economic nations, Germany is in need of energy and raw materials. In the 21st century, marine resources are a prominent and promising alternative to land based resources. However, there are challenges that need to be considered. Rough and often poorly plannable weather conditions prevail distant to the marginal seas. Ice coverage makes offshore services inefficient and costly in Polar Regions. The average ocean depth of 3500m and the associated environment conditions cause difficulties in fulfilling tasks in the deep sea. The project Large Modifiable Underwater Mothership (MUM) [1] will enable more efficient solutions in order to accomplish undersea duties and services in harsh conditions.This joint project comprises workshares from Atlas Elektronik, EvoLogics, thyssenkrupp Marine Systems, the University of Rostock and the Technische Universität Berlin. The principle idea of the project is the conception of a novel vehicle class. With highly modular autonomous underwater vehicles, this class will be capable of undertaking a variety of different tasks. Classically engineered vehicle structures will be split into single basis modules which can be flexibly assembled with specialized mission modules to form potent systems for individual assignments. The group of basis modules consists of units for navigation, vehicle control, propulsion and energy generation via fuel cell technology. The potential reusability of system relevant modules leads to a significant cost reduction and to shortened development periods compared with conventional vehicle concepts. The integration of newly designed additional mission modules is possible with little effort and a separate commercialization of single modules is feasible."

Jan 1, 2017

By Sabrina Warwas, Thomas Kuhn

"Due to rising prices and increasing demand of raw materials over the last years, marine mineral resources including manganese nodules have become a focus of study for industry and science. Marine ferromanganese nodules consist of micro-layers of different chemical and mineralogical composition which incorporate metals of high economic interest (Ni, Cu, Co, Zn, Mo, Li, rare earth elements; Hein & Koschinsky, 2015).The varying composition of the layers depends on different growth processes, such as hydrogenetic (metal precipitation from the water column under oxic conditions; Mn/Fe = 3), diagenetic (metal precipitation from the sediment pore water) under oxic (Mn/Fe 3-10) or suboxic (Mn/Fe = 10) conditions; (Wegorzewski & Kuhn, 2014) or hydrothermal (metal precipitation from low-temperature hydrothermal fluids; Kuhn et al., 2003).METHODSIn this study, manganese nodules from three different locations of the Atlantic Ocean (Galicia Bank; Vema-Fracture-Zone and Brazilian Basin) were analyzed for their geochemical and mineralogical composition. Detailed information about the samples are given in table 1. The geochemical and mineralogical composition of bulk nodules were determined by XRF, ICP-MS/OES as well as XRD and the single micro-layers by high resolution analyses with electron microprobe and LA-ICP-MS."

Jan 1, 2017

By Masaomi Kurihara, Seiya Kawano, Norihiro Yamaji, Satoshi Shiokawa, Nobuyuki Okamoto, Hironobu Sakurai

Seafloor polymetallic sulphides are distributed in the EEZ of Japan, including substantial deposits in the Okinawa Trough and Izu-Bonin back-arc basin. In this new frontier, the successful development of these resources in Japan is expected to bring about a new domestic supply of mineral resources. The initial stages of this development are authorized by the Basic Plan on Ocean Policy, approved by the Japanese Cabinet on April 26, 2013, and the Plan for the Development of Marine Energy and Mineral Resources, formulated by the Ministry of Economy, Trade and Industry (METI) on December 24, 2013. In 2008, the Japan Oil, Gas and Metals National Corporation (JOGMEC), commissioned by METI, began a survey and technological development programme for the development of the seafloor polymetallc sulphides (PMS) based on these Plans. The examination of four different fields: the evaluation of the amount of the resource, environmental assessment, mining technology, and processing & smelting technology, are concurrently promoted, aiming for commercialization as soon as possible. Based on the results of research for properties of geomorphology and marine environments of the target test sites in the Okinawa trough, which have been ongoing for several years, the preparation of the pilot lifting test included an in-situ excavation and crushing test conducted using test excavating and crushing systems.

Jan 1, 2018

By Masaomi Kurihara, Seiya Kawano, Norihiro Yamajim, Satoshi Shiokawa, Nobuyuki Okamoto, Hironobu Sakurai

Seafloor polymetallic sulphides are distributed in the EEZ of Japan, including substantial deposits in the Okinawa Trough and Izu-Bonin back-arc basin. In this new frontier, the successful development of these resources in Japan is expected to bring about a new domestic supply of mineral resources. The initial stages of this development are authorized by the Basic Plan on Ocean Policy, approved by the Japanese Cabinet on April 26, 2013, and the Plan for the Development of Marine Energy and Mineral Resources, formulated by the Ministry of Economy, Trade and Industry (METI) on December 24, 2013. In 2008, the Japan Oil, Gas and Metals National Corporation (JOGMEC), commissioned by METI, began a survey and technological development programme for the development of the seafloor polymetallc sulphides (PMS) based on these Plans. The examination of four different fields: the evaluation of the amount of the resource, environmental assessment, mining technology, and processing & smelting technology, are concurrently promoted, aiming for commercialization as soon as possible. Based on the results of research for properties of geomorphology and marine environments of the target test sites in the Okinawa trough, which have been ongoing for several years, the preparation of the pilot lifting test included an in-situ excavation and crushing test conducted using test excavating and crushing systems.

Jan 1, 2018

By Robert M. Owen

The reconstruction of ocean history has been a major focus of marine research over the past decade. A significant outcome of these investigations is the recognition that certain types of marine mineral deposits are linked to regional to global scale changes in ocean composition and climate conditions. Manganese-bearing deposits are of particular interest in this regard because changes in their occurrence, distribution and/or composition are responsive to both biochemical and geological factors. Analyses of such deposits whose formation spans critical age/epoch boundaries thus provide clues concerning the interplay of different process during anomalous periods in Earth history. Recent studies demonstrating this deposit - event - process relationship include: (1) Changes in the bulk chemical composition of ferromanganese crusts during the Late Miocene-Early-Pliocene (-7-3 Ma) that coincide with a period of enhanced biological productivity in the eastern equatorial Pacific upwelling zone; (2) The formation of large statiform manganese deposits at the Cenornanian- Turonian Boundary (-92 Ma) in association with widespread oceanic anoxia; and (3) Increased deposition of hydrothermal precipitates caused by tectonic reorganizations at the Paleocene - Eocene boundary (-55 Ma) that resulted in global-scale changes in atmospheric and oceanic circulation and climate.

Jan 1, 1995

By Jorge MRS Relvas

Recent research both on active and fossil systems has demonstrated that shallow subseafloor replacement processes are not only viable depositional mechanisms for massive sulfide mineralization, but likely contributed as a major component of the mineralization occurring in large VHMS deposits and in many present-day seafloor hydrothermal systems. In the giant Neves Corvo deposit, as in many others VHMS deposits of the Iberian Pyrite Belt, there is overwhelming evidence for silicate-sulfide replacement processes being largely responsible for the efficiency of the ore-forming systems and huge size of the deposits. Textural evidences at all scales, coupled with a well-constrained mass-balance geochemical analysis, indicate that extensive replacement in the lavadominated volcanic rocks of the footwall sequence, and disseminated replacement mineralization in the volcaniclastic and/or sedimentary units were major mechanisms of ore formation in the Neves Corvo deposit. Shallow metal deposition prior to fluid discharge on the seafloor is likely to play a major role in seafloor massive sulfide mineralization. This premise should be envisaged as critical in evaluating the economic potential of seafloor resources, and should certainly be part of the equation when plans for seafloor mineral exploration missions are drawn.

Sep 14, 2011

By Mayumy Amparo Cabrera-Ramírez

Polymetallic nodules are a widespread resource in the Pacific Ocean, particularly in the areas of Clarion-Clipperton (Cronan, 2000). The most abundant mineral phases are forme d by iron and manganese oxides, with minor elements such as nickel, copper, cobalt, molybdenum and rare earths elements (Cronan, 1977; Cronan and Moorby, 1981; Iyer and Sharma, 1990; Mangini et al. 1990; Banerjee et al. 1991). In the Clarion-Clipperton Zone (CCZ), several authors mention that there are three main mineral species of manganese oxides, which have been recognized and which are associated with different processes of formation: todorokita (Mn2+, Ca, Mg) Mn3 4+ O7. H2), vernadite dMnO and birnessite enriched in Fe and (Na, Ca) 0.5 (Mn4+, Mn3+) 2O4. 1.5 H2O. In nodules of hydrothermal origin have been found todorokite, birnessite, vernadite, goethite and pyrolusite. Although there are many oxides and hydroxides of manganese and iron in amorphous and microcrystalline phases that make up the bulk of the nodule (Frondel et al. 1960; Cronan 1977; Dymond 1981; Calvert and Piper, 1984; Aplin and Cronan, 1985; Martin and Lallier, 1993; Achurra et al. 2009), identifying specific mineral phases is difficult due to the intergrowth of different phases and associated detrital material.

Sep 14, 2011

By Yves Fouquet

Recent exploration demonstrates that hydrothermal systems related to upper mantle ultramafic outcrops are common in the modern ocean. Most sites are located on slow spreading ridges with a low magmatic budget. Volcanogenic Massive Sulfide (VMS) deposits, associated with basalt, along the Mid Atlantic Ridge (MAR) are volcanically controlled near the topographic highs at the center of the segments. Three preferential settings are identified for ultramafic sulfide mineralization: 1) Off axis, on rift valley walls, near the amagmatic ends of the segments; 2) Non-transform offsets and 3) Ultramafic dome structures at the ridge transform fault intersection. The upper surface of these domes is often interpreted as a detachment fault. Three processes are considered for driving hydrothermal cells in ultramafic rocks: 1) regional heat flow at the ridge axis 2) Cooling of a deep gabbroic intrusion and 3) exothermic heat produced during serpentinisation. Along the Mid Atlantic Ridge, four types of ultramafic hydrothermal mineralization are observed: 1) High temperature (>350°C) sulfide mineralization related to low pH fluids, (ex. The Logachev field at 14°45? N and the Rainbow field at 36°14 N); 2) Medium temperature carbonate chimneys (<100°C) related to high pH fluids (ex. The Lost City site at 30°N); 3) Low temperature diffuse venting associated with extremely high methane discharge and pervasive alteration and silicification of both volcanic and ultramafic rocks (ex : The Saldanha field at 36°34 N); 4) Stockwork mineralization and quartz veins with sulfides related to gabbroic intrusions within ultramafic rocks (15°N). When compared to mineralization in a basaltic environment, sulfide deposits are enriched in copper, zinc and specific elements related to an ultramafic rock source such as Ni and Co. They are also significantly enriched in gold which, unlike in basaltic environments, has a bimodal occurrence both in low temperature Zn-rich assemblages and in high temperature Cu-rich mineral assemblages. The Cu-Zn-Co-Au deposits along the Mid Atlantic Ridge seem to be more common than on land where few similar VMS deposits are known. We consider that ultramafic VMS deposits on slow spreading ridges constitute a specific marine type of mineralization that is less easily than back arc deposits, incorporated into the continent during obduction processes.

Jan 1, 2004

By Wiebe Boomsma

This is a framework study financed by the Maritime Innovation Programme of The Netherlands and several institutions actively involved in the research of the environmental impact of deep sea mining; IHC Mining, MTI Holland, Delft University of Technology, NIOZ, IMARES, Boskalis Westminster, AllSeas and TNO. For this framework study the following mining activities have been identified to be relevant to assess the ecological impact of a deep sea mining operation: a) excavation, b) tailings return, c) vertical transport, d) vessel operations, e) ore transport and f) general operations. For this paper, only one mining activity has been selected as an example for the assessment of ecological effects. This is one of the main activities introduced by the new technology envisaged for developing deep sea mining: tailings return.

Sep 14, 2011

By R. C. Newell

The primary objective of this study was to establish the fate and distribution of material rejected during marine aggregate dredging, and the extent to which this is associated with spatial changes in biological community composition. Two actively dredged sites in the southern North Sea (Licence Areas 430 and 106) were selected in order to provide a comparison of impacts between sites subjected to different levels of dredging intensity and of contrasting environmental conditions. Dispersal of material rejected during the dredging process was monitored by means of acoustic doppler current profiling techniques (ADCP). Composition of the substratum and benthic invertebrate assemblages were investigated by the analysis of seabed grab samples. It was found that dredging in both areas had an impact on seabed bathymetry in the form of dredge furrows and also led to a reduction of the coarse gravel-sized components of the worked area. Sand sized particles were shown to increase in the surface deposits of both dredged areas. This is likely to reflect both the removal of coarse particles as cargo and the settlement of finer particles rejected during overboard screening. Dispersion and settlement profiles of material rejected by dredging vessels suggested that the majority of the suspended sediment load resulting from overboard screening settles to the seabed within 500 m. Some evidence of suspended sediment loads above background levels were noted at distances of up to 2 km from the working vessel. Analysis of the particle size composition of the deposits, along the axis of transport of material from the dredged sites, suggested that the impact on the sediment composition outside the boundaries of the dredged sites is dependent on the strength and direction of net sediment flux at the seabed. Benthic invertebrate communities within the dredged zones of both areas were found to differ significantly from communities in nearby undredged deposits. A major suppression of species richness and abundance was noted in the dredged sectors of both sites when compared to control locations. A ?footprint? of potential impact on the benthic fauna was noted in samples taken along the axis of sediment transport at distances of up to 1750m outside the boundaries of Area 430. In contrast, impacts on benthic community structure at Area 106 appeared to be confined to the immediate vicinity of the dredged zone itself. This apparent difference in impacts, beyond the boundaries of the dredged sectors between the two study sites, was thought to be a reflection of the smaller quantities of material rejected at Area 106 and the weak seabed sediment flux which is characteristic of this area. These findings, along with those of numerous dredging impacts studies, were then used to make generalised predictions of macrobenthic community recovery following marine aggregate extraction in a variety of seabed habitats.

Jan 1, 2004

By Jeremy Spearman, Alan Cooper, Mark Lee, Jon Taylor, Michael Turnbull, Neil Crossouard, Bramley Murton

"SUMMARYSeamounts are underwater mountains caused by volcanic activity. They are of great oceanographic interest because of their local and basin-scale influence over ocean systems, their often unique ecosystems, and because they are associated with the formation of ferromanganese (Fe-Mn) crusts. These crusts are of particular interest to scientists because they are rich in some of the rare elements increasingly required for development of renewable technologies. When the possibility of mining such seamounts is considered, an inter-disciplinary study of seamount hydrodynamics, crust formation and ecosystem sensitivity is required. MarineE-tech is one such multi-disciplined project that has been commissioned to address these different aspects in order to improve understanding of the viability and desirability of mining Fe-Mn crusts. This paper describes a key part of this study, namely the development of a model, informed by hydrographic observations, of the currents around one such seamount and the in situ validation of a sediment disturbance plume model as a pre-cursor to assessment of the potential effects of mining activity.INTRODUCTIONFerromanganese crusts are thought to form by precipitation of iron and manganese oxides from oxygen depleted mid-water known as the oxygen minimum zone (OMZ). Oxidation rich waters, typically at depths of about 800-2200 m (Hein et al, 2000). This range of depths coincides with the flanks and summits of many seamounts. The ferromanganese crusts found on seamounts have been found to have high concentrations of rare elements, like Tellurium, that are considered critical to low-carbon energy production. Seamounts are complex environments: in terms of the local hydrodynamics that tend to trap water over the seamount due to the Taylor Cap effect (e.g. Chapman and Haidvogel, 1992) and which can enhance the productivity of seamount waters through upwelling (Lavelle and Mohn, 2010), in terms of the microbiological activity that leads to the precipitation of the Fe-Mn crusts, and also in terms of the often unique ecosystems that are the product of the “island” nature of seamounts and the upwelling of nutrients. The understanding of this complexity is a necessary journey towards the realization of viable, yet environmentally responsible, mining schemes. The formation of crusts will be influenced by the local (and larger-scale) hydrodynamics. The exploration of promising crust sites could be made much more efficient by understanding where the most prospective deposits are likely to occur. Knowing how to remove these crusts without impacting significantly on the local environment will be a pre-requisite for such mining to be acceptable to the public and funders alike."

Jan 1, 2017

By Boris Broere, Wiebe Boomsma, Pieter Lucieer

"The Blue Nodules project started February 2016 as part of the EU Horizon 2020 subsidy program. Blue Nodules aims at developing a sustainable deep sea mining system for the harvesting of polymetallic nodules from the sea floor. Blue Nodules is closely related to the Blue Mining and Midas projects, both EU subsidized projects. Blue Mining mainly concerned the development of technical capabilities to adequately and cost-effectively discover, assess and transport deep sea mineral deposits up to 6,000 m water depths. The MIDAS project - Managing Impacts of DeepseA reSource exploitation - was a multidisciplinary research programme investigating the environmental impacts of extracting mineral and energy resources from the deep-sea environment.The Blue Nodules project is divided in seven work packages defined to develop mining equipment and process equipment, to assess and integrate environmental, economic and technological aspects and to assess and minimize the environmental impact of mining polymetallic nodules.This abstract will address part of the work performed in the second work package called: ‘Subsea harvesting equipment and control technology’. The main topic addressed will be the development of a propulsion system to manoeuvre the harvesting system. The propulsion system will be developed with full incorporation of economical and compliance requirements and to have a minimal environmental impact.SummaryBased on information gathered in the 70’s during the first studies into polymetallic nodules mining and more recent data and developments, an initial full scale design of the propulsion system is developed. The largest challenge for the propulsion of a deep sea mining vehicle is to drive on the soft sediments associated with these deep sea environments. A short summary of the initial design criteria is given below."

Jan 1, 2017

By Freddy Pøhner

The paper describes recent advances in the technology for mapping of the seabed with acoustic instrumentation. These instruments are typically single beam echo sounders, multibeam echo sounders and high resolution sub bottom profiler. For the single beam echo sounders, new features for deep water mapping are described, as well as the possibility for combining investigation of shallow areas with side scan sonar and vertical echo sounding in the same instrument. Multibeam echo sounding technology for deep and shallow water is reviewed, and some new high resolution instruments using dynamic beam focusing is presented. The sediment profiling technology deals with a novel design for high resolution sub bottom profiling, based upon a Mills Cross transducer with resolution as good as 3 degree in its largest configuration and a frequency range of 2,5 ? 7 kHz. Remarkable features of the system are a very high ping rate even for deep water, and the capability to map buried objects or structures by several simultaneous beams. Some results obtained with the first installation on the French research vessel ?Beatemps Beaupré? are presented.

Jan 1, 2003

By Tatiana ?. Sedysheva, Vladimir V. Ivanov, Michail E. Melnikov, Irina A. Pulyaeva

"INTRODUCTIONHydrogenetic Fe-Mn crusts are ubiquitous in the ocean basins and play an important role in marine mineral-deposit research because of their widespread occurrence and high concentrations of valuable and rare metals. Directed research, which started in the last quarter of the 20th century, has provided significant results, with substantial amounts of data produced on Fe-Mn crusts structure, composition, and distribution in the global ocean [3, 4 - 8]. Now, commercial interests gain more and more attention. Mining systems are being developed which involve fragmentation of the crusts and their separation from the substrate. The effectiveness of such activities greatly depends on physico-mechanical characteristics of the crusts and rocks on which they form. This determines the importance of the engineering geological study of the objects.This article comprises the results of the engineering geological studies of the crusts samples (72 samples) and their underlying rock substrates (75 samples), which were carried out during the research cruises 6-06, 6-07, 6-08, 6-13 (2006-2013) on the Magellan Seamounts guyots in the Western part of the Pacific Ocean by the specialists of the State Scientific Centre Yuzhmorgeologia [10 - 13, 19, 20]. The authors of the article directly participated in the studies mentioned above.MethodsEngineering geological studies were carried out on board of the research vessel Gelendzhik and in the laboratories of NPA «Sevmorgeologiya». The studies involved the determination of the following parameters:"

Jan 1, 2017

By M. Ye. Melnikov

The report is about oceanic ferromanganese crusts ? covers of iron and manganese hydroxides developed over an opened rock of seamounts and rises. Ore bed parameters of crusts are understandable as their thickness and content of main economic components ? manganese, cobalt and nickel. All known results of research activity on ferromanganese manganese crusts point to that crust are characterized by notable variability of thicknesses and composition. It is possible to separate few levels of variability. The most evident is the first level of parameters variability, which is manifested in various regions of the Ocean, and connected first of all, with an age of submarine mountains, a host objects for a crusts. It was proved by many authors, that most powerful crusts are connected with submarine mountains of Cretaceous age. [1]. Crust thickness at the Magellan Seamounts reaches, for example 12-15 cm, sometimes exceeds 20-22 cm. Thicknesses of Hawaii Archipelago or Tuamotu crusts in 3-4 times less. Biostratigraphy studies of crustal sections at the Magellan Seamounts already show, that its main part started to form in the Late Paleocene. Four layers with well expressed features in structure and composition of a layer are separated in the section. From foot to top: Late Paleocene ? Early Eocene layer I-1, Middle-Late-Eocene layer I-2, Miocene layer II and Pliocene ? Quaternary layer III. Relics of more ancient Campanian ? Maastrichtian ore layer [2, 4] were discovered. It is evident for example, that Oligocene mountains could not be a host for two lower layers in the crust section.

Jan 1, 2010

By M. Ye. Melnikov

The report is about oceanic ferromanganese crusts ? covers of iron and manganese hydroxides developed over an opened rock of seamounts and rises. Ore bed parameters of crusts are understandable as their thickness and content of main economic components ? manganese, cobalt and nickel. All known results of research activity on ferromanganese manganese crusts point to that crust are characterized by notable variability of thicknesses and composition. It is possible to separate few levels of variability. The most evident is the first level of parameters variability, which is manifested in various regions of the Ocean, and connected first of all, with an age of submarine mountains, a host objects for a crusts. It was proved by many authors, that most powerful crusts are connected with submarine mountains of Cretaceous age. [1]. Crust thickness at the Magellan Seamounts reaches, for example 12-15 cm, sometimes exceeds 20-22 cm. Thicknesses of Hawaii Archipelago or Tuamotu crusts in 3-4 times less. Biostratigraphy studies of crustal sections at the Magellan Seamounts already show, that its main part started to form in the Late Paleocene. Four layers with well expressed features in structure and composition of a layer are separated in the section. From foot to top: Late Paleocene ? Early Eocene layer I-1, Middle-Late-Eocene layer I-2, Miocene layer II and Pliocene ? Quaternary layer III. Relics of more ancient Campanian ? Maastrichtian ore layer [2, 4] were discovered. It is evident for example, that Oligocene mountains could not be a host for two lower layers in the crust section.

Jan 1, 2010