Search Documents

"Gravity concentration remains the main separation method for fine iron ore and is used extensively for treating various minerals. Gravity concentration methods separate minerals of different specific gravity by their relative movement in response to gravity and one or more other forces, the latter often being the resistance to motion offered by a viscous fluid, such as water or air (Wills, 2006).Spirals concentrators are one of the gravity concentration equipment used for beneficiation of minerals. Spirals are typically used for processing of fine minerals (-1mm) size fraction. The main operating variables for a spiral concentrator are the feed rate, the solids concentration, the wash water addition and the position of the cutters or splitters used to separate the tailings, middling and concentrate streams (Sadeghi, Bazin & Renaud, 2014).The aim of this study is to investigate the effect of feed rate, solids concentration and wash water on grade and recovery on iron ore material. The Multotec SC20HC/7 WW spiral was used for the experimental test work. The spiral was tested at varying solids concentration and feed rate. The wash water rate was also varied to establish the best washing rate. The splitter positions were kept constant. Optimization of these variables is expected to provide optimum conditions for a good compromise between grade and recovery.INTRODUCTIONSpiral concentrators are simple low energy consuming devices that separate minerals mainly on the basis of density. Spirals are widely used in mineral processing as a method for preconcentration and have proven to be metallurgically efficient and cost effective.Spirals have a wide application, they are used in iron ore processing, coal, gold, chromites, mineral sands, glass sands, and in soil cleaning.Separation on a spiral is achieved through a combination of forces that act on particles as they move down the trough of the spiral. The main forces known to act on the particle on a spiral are the gravitational forces, centrifugal force, hydrodynamic drag, and lift and friction forces (Kapur & Meloy, 1998). Apart from the forces acting on a spiral, the properties of the slurry flowing on a spiral including, solids concentration, feed rate and wash water also plays an important role in the separation on the spiral.The relationship between separation efficiency and feed rate was shown to be linear, with a decrease in efficiency at higher flow rates. Previous work on flow profile by Holland - Batt (1990) indicated that any increase in the feed rate to a spiral results in a greater part of the additional flow volume reporting to the outside of the trough. The flow on the outside of the trough becomes energized and consequence to that the heavy particles find it hard to settle and escape this region to the inner region. This effect has a high impact on recovery of heavy minerals, since any increase in volumetric flow on the spiral is not made available for recovery in the inner region of the spiral."

Jan 1, 2015

By J. E. Sepulveda, R. Morrow

"In full scale mineral grinding operations, the steel balls normally utilized as auxiliary grinding media get to be consumed at different specific rates, as determined by 3 basic mechanisms: abrasion/corrosion (wear), impact ball breakage and impact surface spalling, the latter relating to the removal of rather small pieces of steel coming off the exposed surface of the balls due to repetitive impact with other balls in the charge or the surrounding mill liners. In conventional ball milling applications, the clearly predominant mechanism is gradual wear by abrasion/corrosion. In the case of SAG mills, where the make-up balls may be as large as 6”f diameter, breakage and spalling mechanisms are significant contributors to total ball consumption, although not to the extent of overriding wear mechanisms.Ball wear has been well characterized by the Linear Wear Theory, as presented at the last CMP 2014. Impact breakage has been customarily monitored, at the ball manufacturing site, via Drop Ball Tests (DBT) consisting of repeatedly dropping balls from a standard height and accounting for the number of broken balls and the weight loss (spalling) of the remaining unbroken balls. When properly conducted, DBT’s should provide meaningful indications of the breakage and spalling resistance of large diameter balls. The current publication is focused on the interpretation and projection of DBT results to full industrial scale, taking into account all 3 mechanisms of grinding media consumption in SAG mills.INTRODUCTIONA thorough, quantitative understanding of the independent contribution of all active grinding media consumption mechanisms is of the highest practical relevance, particularly in semiautogenous (SAG) milling operations where ball breakage and spalling can not be ignored or neglected, as it has been normally acceptable for conventional ball milling processes. The high severity impact conditions currently imposed in typical SAG mill environments create serious challenges to the manufacturers and suppliers of large diameter (5”–6”) SAG balls, whose products must be capable of surviving such harsh operational conditions with minimum breakage or spalling."

Jan 1, 2015

"This paper reviews the chemistry involved in the recovery of gold from cyanide solution with anion-exchange resins, and also discusses the most critical aspects of the engineering of an effective resin-in-pulp (RIP) process. As far as the chemistry is concerned, the conclusions reached by a great many researchers, as well as the performance of the only operating RIP plant in the Western World, at the Golden Jubilee Mine in South Africa, support the view that the process is technically viable and, in many cases, could prove to be more attractive economically than alternative processes such as zinc cementation and carbon-in-pulp (CIP). On the engineering side, there is still a need for further development before larger scale ( > 50,000 tpm) RIP plants can be designed, built and operated with confidence. However, the experiences gained during nearly 3 years of operation of the Golden Jublee RIP plant indicate that the process can be engineered with confidence for smaller operations ( < 50,000 tpm), and this will probably be the scope of application of the first-generation RIP plants. INTRODUCTIONThe use of anion-exchange resins in gold processing has, for a number of years, been proposed as an alternative to more conventional processes such as zinc cementation and carbon adsorption, and detailed research programs that have been carried out at a number of laboratories have demonstrated the technical viability of the process. (Burstall et al, 1953, Davison et al., 1960, Tataru, 1973, Laskorin et al. 1978, Hosking, 1984, Riveros and Cooper, 1987 and Palmer et al., 1988)The main incentive for this work was the fact that resins have several characteristics that are quite different from carbon, which make them potentially more attractive substrates for the recovery of gold. The following are examples: -"

Jan 1, 1991

By Ben Murphy, Tomi Maksimainen, Antti Rinne, Ishmael Muzinda, Toni Mattsson

"A 500m3 flotation cell was commissioned during 2014 at the Kevitsa Mine in northern Finland working as the first rougher in the copper flotation circuit. Treating around 850tph with an average grade of 0.3% Cu, the TankCell® e500 has run with an average copper recovery of 71% and an average enrichment ratio of 50 during early optimization test work. In addition the cell has proved to be very energy efficient, being operating with a specific energy of around 0.4kW/m3 under production conditions.A review of the installation and operation of the TankCell® e500 at Kevitsa will be presented. Metallurgical performance of the cell during the operating period will be discussed on the basis of on-line analysis and the metallurgical samples collected during early optimization campaigns.IntroductionThe past three decades have seen a rapid increase in the size of mechanical flotation cells. This has been largely driven by demand from the copper industry to process larger volumes of material due to combination of declining head grades and the desire to benefit from the economies of scale (Lynch, Harbort and Nelson 2010). During this period Outotec has been at the forefront of development of large flotation technology with an enviable scale-up track record; 100m3 (1995), 160m3 (1997), 200m3 (2002), 300m3 (2007), 500m3 (2012) to the largest commercially available cell at 630m3 in 2013. This scale-up methodology has been developed, tested and validated (Elgueta et al., 2009; Coleman & Dixon, 2010) by the large installation base of cells in the 300m3 size class operating (over 400). The learning from large cell operation are then reviewed and incorporated back into new designs and scale-up practices (Murphy, Miettinen, and Yanez, 2014)."

Jan 1, 2016

By I. Le May

"The assessment of integrity in plants is discussed, together with the codes that are being developed for in service evaluation of engineering fitness for service. The use of Risk Based Inspection is described and some examples are provided of the evaluation of in service components in which flaws have been detected. An example of the assessment of the structure of a mine processing facility is described, and application of Risk Based Inspection and plant assessment procedures to mines is discussed. Periodic assessment of large plants and components to determine their integrity for continued safe operation is becoming a more accepted approach than formerly when regular shutdowns were the normal practice. This is on the way to becoming the preferred procedure for petrochemical plants and power generating plants, and the same philosophy is appropriate for many mining operations. Both the American Petroleum Institute (API) and the American Society of Mechanical Engineers (ASME) have committees developing codes for the continued operation of equipment as distinct from the existing design codes. The philosophy is one of risk-based inspection, which can be on a purely qualitative basis or more quantitatively based.The purpose is to reduce the inspection of unnecessary and non-critical items and to concentrate on the most critical components, reducing costs and downtime and increasing safety. The approach differs from that considered by many maintenance engineers, in that defects that are identified during an integrity evaluation do not automatically cause a component or structure to be condemned or require that repairs are made right away. The seriousness of the defect must be considered and the safe operating life can be estimated before it becomes necessary to replace or repair the unit or component. This is no different from what is done today with passenger aircraft and, to an increasing extent, with pressure vessels, reactor vessels and similar components in the petrochemical and power generating industries."

Jan 1, 1998

By K. J. Boser

"Medium Voltage (MV) metal clad switchgear is referred to as the voltage class from 2.4 kV to 38 kV. Technological advances in circuit breaker designs over the last 20 years have given rise to retrofit options in lieu of complete replacement for older outdated circuit breaker technology. This paper examines the four MV breaking techniques that exist in industry and investigates various retrofit versus refurbish options for switchgear modernization and life extension. IntroductionThe life extension and upgrade of medium voltage circuit breakers is becoming an increasingly important issue in today’s modern industrial facilities from both a reliability and safety standpoint. Unscheduled downtime, loss of production, and plant safety issues are just some of the concerns that need to be addressed with aging switchgear. A thorough examination of the available breaking mediums allows an informed decision to be made when the time comes to assess equipment performance. If you look back over the history of medium voltage breakers, you will find that there have been four breaking techniques developed and widely used:• air magnetic;• minimum oil;• vacuum; and• SF6.Many facilities that were constructed 25 to 30 years ago relied on air magnetic or minimum oil circuit breakers in their distribution systems. At the time, these were the only “tried and tested” options and they afforded good service. Since then, however, newer technology has given us the vacuum and SF6 mediums which have both proven their reliability and monopolized the market. All the methods have their particular place in industry and what follows is a summary of the advantages, disadvantages, and chronological development of each breaking technique."

Jan 1, 1998

By Anthony J. Deevy

"Abstract -The Magino gold mine is located 45 km northeast of Wawa, Ontario. There was limit­ ed gold production in the Iate thirties. The present operation was officially opened in October 1988 and produced gold until September 1992. It was a 635 tonnes per day, decline-accessed mine, with ore coming from several small blast hole and shrinkage stopes.The host for the gold is the Webb Lake granodiorite stock which was intruded into the Goudreau Lake Deformation Zone. This east-northeast-striking deformation zone overprints the generally east­ west-striking isoclinally folded metavolcanic and metasedimentary rocks, which make up the east end of the Michipicoten greenstone belt. The ore-shoots are controlled by dextral delatancy associated with the Goudreau Lake Deformation Zone. Shearing, bleaching and silicification accompanied the gold emplacement."

Jan 1, 1994

By M. C. Bétournay

Under the requirement to define the economic advantages of using hydrogen fuel cell vehicles, a broad-scoped project was initiated to quantify the costs associated with operating fuel cell vehicles and diesel vehicles. While ventilation savings are clearly an advantage for the former, a complete and detailed analysis of this and other operational and capital cost elements was undertaken in order to provide the mining industry with factual information in considering the changeover from one technology to another. This paper outlines the results of the investigations to date defining the costs/benefits associated with capital purchases, operations (electrical/diesel, mine air heating fuel, ventilation, openings, surface and underground infrastructure, maintenance, labour, etc.), delivery of energy, regulatory obligations, and mine production. Considerations are given to the type and size of a mining operation, the depth, and location in North America. Significant ventilation power, equipment, and infrastructure savings are possible with the application of fuel cells for shallower mine applications. At depth, where heat is an issue, there is a reduction in benefit. Specific qualifiers such as minimum air velocities, dust dilution, shaft, and heating system velocity limits must be considered on an individual mine basis. While the capital cost for fuel cell mining equipment is currently higher than diesel versions, the high cost of fuel cells is anticipated to be reduced significantly in the near future with the intensification of manufacturing. In either case, the operational savings would probably be sufficient to balance the supplementary capitalization costs. Comprehensive reports have been issued.

May 1, 2005

By G. Righettini, G. Desrivières, P. Mousset-Jones, R. Lacroix, M. C. Bétournay, P. Laliberté, S. Hardcastle

"Under the requirement to define the economic advantages of using hydrogen fuel cell vehicles, a broad-scoped project was initiated to quantify the costs associated with operating fuel cell vehicles and diesel vehicles. While ventilation savings are clearly an advantage for the former, a complete and detailed analysis of this and other operational and capital cost elements was undertaken in order to provide the mining industry with factual information in considering the changeover from one technology to another.This paper outlines the results of the investigations to date defining the costs/benefits associated with capital purchases, operations (electrical/diesel, mine air heating fuel, ventilation, openings, surface and underground infrastructure, maintenance, labour, etc.), delivery of energy, regulatory obligations, and mine production. Considerations are given to the type and size of a mining operation, the depth, and location in North America.Significant ventilation power, equipment, and infrastructure savings are possible with the application of fuel cells for shallower mine applications. At depth, where heat is an issue, there is a reduction in benefit. Specific qualifiers such as minimum air velocities, dust dilution, shaft, and heating system velocity limits must be considered on an individual mine basis. While the capital cost for fuel cell mining equipment is currently higher than diesel versions the high cost of fuel cells is anticipated to be reduced significantly in the near future with the intensification of manufacturing. In either case, the operational savings would probably be sufficient to balance the supplementary capitalization costs.Comprehensive reports have been issued."

Jan 1, 2005

By Gaby Steinbach

A novel synthesis is described for the preparation of supported gold catalysts for low-temperature CO oxidation. The novel route is a variation of the inverse co-precipitation method and requires amphoteric metal hydroxides, with zinc and aluminium hydroxides chosen. Catalysts were prepared by inverse co-precipitation (ICPa) and by the novel route (ICPb) and tested for CO oxidation at 60ºC. Preliminary results showed the novel route to be superior to ICPa; the catalysts prepared by ICPb showed higher catalytic activities. The effect on catalytic activity of parameters such as pH, calcination temperature, washing of precursor and calcined catalysts and ageing was investigated. A preparation pH of 9 and a Zn to Al mass ratio of 3 proved to be optimal. It was possible to remove residual chloride by washing thereby enhancing catalyst performance. Ageing and Mg citrate addition were also shown to improve catalyst performance. Characterization of the catalysts revealed that better activities were obtained when the support was more crystalline and had a higher surface area. The presence of carbonate-containing species in the support decreased catalytic activity. 197Au Mössbauer Spectroscopy revealed the presence of Au3+ when catalysts were heat-treated at temperatures of 200ºC and below. Catalysts calcined at 400º had 75% of the gold present as Au0, with the remaining gold present as Au3+.

Oct 1, 2003

By Ian D. Pirie

Presentation outline ?Project location ?Geology ?Resources and reserves ?Results of the FEED study ?Social and environmental considerations ?Project path forward

May 1, 2010

By Filip Rochette, Yvan De Busscher

Extraction of minerals can be achieved by a variety of technologies; one of them is ion exchange. There are several ion exchange configurations and mechanical set-ups available, but only one technology will provide more process performance and flexibility compared to the other. The multiple column Continuous Countercurrent Ion Exchange (CCIX) technology provides the highest form of process flexibility with also the highest mineral recovery feasible through ion exchange. In comparison with a fixed bed system, the PuriTech CCIX system offers the benefits of continuous counter-current contact mode. This way the resin capacity is fully exploited leading to reduction in resin inventory and, at the same time, in chemicals and water consumption, and product dilution. For any set of operating conditions the mass transfer zone has a characteristic length (MTZL). The MTZL can be expressed in duration, column length, or volume, but is the measure of the quantity of resin in the system that is doing "work" at any given moment in the process. The objective of continuous ion exchange processing is to eliminate all resin volume from the process equipment that is not within a mass transfer zone. In most commercial ion exchange processes for the recovery of metals, CCIX engineering can eliminate as much as 20 - 80 % of the ion exchange resin inventory. Consumptions of water and chemicals are typically brought down around 40% or more. For each type of resin the selectivity/affinity towards a particular metal depends on the basic process conditions such as pH, concentrations of other competing metals in solution. By changing the pH in the ion exchange process phase, the selectivity of the resin can be changed. By doing this, a split elution, or extraction of metals separately can be achieved and the effect of other competing metals (cross-contamination) can be reduced. For example the DOW resin XUS43578 is commonly used for the recovery of copper or nickel/cobalt separation.

Jan 1, 2016

By Mark Ferra

Flotation is used in mining to produce concentrates of copper, gold and several other valuable ores. In 2017, a copper mine near Globe, Arizona improved their rougher cells productivity using technically advanced electro-hydraulic actuators in the flotation process by enabling excellent tank pulp level process stability. The new actuators controlled the dart valve position to allow pulp to leave the cell. Tank cell pulp level can change due to feed and discharge fluctuations from neighboring tanks. When traditional pneumatic actuators are used, they have sluggish response times and overshoot due to the inherent physical property of air being compressible. Electro-hydraulic actuators have the benefit of hydraulic stiffness to deliver accurate and repeatable (0.1%) dart valve positioning. The froth layer has more opportunity time to maximize mass transfer into the launderer. The results are an increase in copper recovery by 2-4%. INTRODUCTION In 2013 there was an international flotation technical conference well attended by respected flotation specialists for both mining companies and academia. During the technical session a leading metallurgist was discussing pulp level measurement and said that when he was on the cell deck he stated, pneumatic actuators air cylinders stroking up and down. The presenter then claimed with confidence that "I listened to actuator move so the pulp level in the tank was being controlled!" No one questioned his assumption and I can assert that the audience was quite technical and not shy in their critiques of speakers. The flotation community simply believed that the existing pneumatic technology was enough with no alternative. Having a stable flotation cell pulp level is critical to effective copper recovery. Controlling pulp levels in flotation cells is a complex task that includes modulating dart valves in each cell. The use of REXA Electraulic actuators will decrease the process dead time and maintain froth height in a controlled manner, especially from pulp slurry volume fluctuations from neighboring cells. By reducing flotation cell pulp level tank height variation, a copper mine in Arizona has realized a 2-4% recovery improvement by increasing the froth transfer to the launderers in the rougher cell circuits compared to pneumatic actuators. This paper examines the benefits of using an electro-hydraulic actuator to ensure proper pulp level control and reduce the process operational cost. It will focus on actuator positioning the dart valves to maintain pulp level setpoint at a copper mine in Arizona.

Jan 1, 2019

By T. Hidayat, D. Shishin, S. Sineva, M. Shevchenko

The effects of the slagging components Al2O3, CaO and MgO on the thermodynamics and phase equilibria of the gas/slag/matte system with major elements “Cu2O”-“FeO”-SiO2-S are characterised using an integrated experimental and thermodynamic modelling approach. The experimental technique included high-temperature equilibration experiments using a spinel substrate in controlled gas atmosphere (CO/CO2/SO2/Ar), quenching of the sample and subsequent measurement of the compositions of equilibrium phases with Electron Probe X-ray Microanalysis (EPMA). Thermodynamic modelling is undertaken using the computer system FactSage. In previous experimental studies on this system, the separate effects of Al2O3, CaO and MgO were determined. In the present investigation, the combined effects of these additional components are investigated at 1200oC and P(SO2) = 0.25 atm and a range of P(O2)’s. Special attention is paid to ensuring chemical equilibrium is achieved in each case, for this reason possible kinetic factors are systematically analysed. The results obtained are presented in the form of graphs showing the compositions of matte and slag phases as functions of copper concentration (matte grade). The new experimental data are used for the improvement of the thermodynamic database for multicomponent copper-containing systems. The effects of the slagging elements on this multicomponent system will be presented in the paper. INTRODUCTION Whilst Fe-O-Si form the principal components of copper smelting and refining slags, additional impurities are present in industrial practice typically at 2–5 wt.% Al2O3, 1–4 wt.% CaO and 1–2 wt.% MgO levels (Davenport, King, Schlesinger, & Biswas, 2002). These elements are introduced into the slag as impurities in concentrates and other feedstocks, in fluxes added to the process and in refractory materials. Understanding, and accurate description, of the changes that take place in the smelting process in the presence of these additional elements is of major importance to the optimization of industrial operations. Although experimental data are available on slag/copper matte equilibria, further work is needed to accurately characterise the influence of Al2O3, CaO and MgO on phase equilibria and elemental distributions of elements in gas/slag/matte systems. The individual effects of the Al2O3, CaO and MgO slagging components on equilibrium phase assemblages under selected conditions have been quantified in a recent series of studies on the Cu–Fe–O–S–Si-(Al, Ca, Mg) gas-slag-matte-metal system (Fallah- Mehrjardi, Hayes, & Jak, 2018; Fallah-Mehrjardi, Hidayat, Hayes, & Jak, 2017a, 2017b; Hidayat, Fallah-Mehrjardi, Hayes, & Jak, 2018a, 2018b; Jak et al., 2016; D. Shishin, Decterov, & Jak, 2018; Denis Shishin, Hayes, & Jak, 2018). Since, thermodynamically, the condensed phases do not behave ideally, it is to be expected that the effects of individual elements may not be additive, and the additional interactions between the Al2O3, CaO and MgO slagging components will also have to be taken into account. These additional effects are expected to be smaller than those of the individual components, so higher accuracy is needed. The present paper describes analysis of the precision and accuracy of the experimental technique on multi-component, multi-phase equilibria in these systems to enable the combined effects of Al2O3 + CaO + MgO on slag/matte/spinel equilibria, i.e. for high Fe/SiO2, to be accurately measured. The effects of Al2O3, CaO and MgO on the gas - slag - matte are analysed using a thermodynamic modelling approach with the computer package FactSage.

Jan 1, 2019

By Max W. Ball

THE world&apos;s largest known oil deposit lies in northern Alberta. In fact, according to government estimates, the famous so-called &apos;tar sands&apos; of the Athabaska region contain several times as much oil as all the other proved reserves of the world. S. C. Ells, of the Department of Mines and Resources, who has been the Dominion Government&apos;s authority on the oil sands since 1913, has estimated the minimum content of the deposits at 100 billion barrels(!). C. P. Bowie, of the U.S. Bureau of Mines, has published an estimate of 250 billion barrels(2). ?In comparison, the latest authoritative estimate of the proved oil-field reserves of the world is less than 35 billion barrels(3). Out of this tremendous total, perhaps 500 million barrels are commercially available at present-day costs and prices; the remainder must be considered a latent reserve to be used when development costs are materially lower and petroleum prices materially higher than they now are. Mean-while, the 500-million-barrel portion presently available contains more oil than has been found in all the rest of Canada, and constitutes one of Canada&apos;s great mineral resources. Although these deposits have been known to white men since 1788, when Peter Pond, the explorer, found the Indians stewing the oil out of the sand and mixing it with spruce pitch to caulk their canoes, they are only now coming into commercial production. The purpose of the present paper is to describe the deposits, their oil content, their present development, and the possibilities that seem to lie immediately ahead. For the sake of completeness and clarity, the writer has not hesitated to use or to paraphrase material that he has previously published elsewhere in discussing various aspects of the oil sands.

Jan 1, 1941

By T. G. Joseph

"The Oil sands-Equipment Interactions Program (OsEIP) is a collaborative research venture between Syncrude Canada Ltd., James Progithin International Ltd. (JPi), the University of Alberta, P&H MinePro, and Caterpillar Inc. The objective is to better understand the behaviour of oil sands as it interacts with mining equipment, in particular, large trucks and shovels. With a move to ever larger equipment, mining oil sands of highly variable bitumen content, ground stability comes into question. This paper outlines this aspect of OsEIP and provides some insight into how some of the findings enable an improved understanding of oil sands behaviour that may impact large equipment design, operational and maintenance strategies. IntroductionThe mechanical behaviour of oil sands in the underfoot and in the face yields some of the harshest stability and digging conditions of any mining environment. High maintenance costs from truck and shovel fatigue failures predominate as a result of ground stability issues. Wear rates of shovel and dozer ground engaging tools (GET), rollers, roller paths and crusher screens result in costly and frequent replacement, or even more frequent and costly sacrificial wear zone building. From the shovel face to the crushers and screens, dry oil sands mechanics affects the degree of fragmentation and, ultimately, bitumen production.An increased knowledge of the behaviour of oil sands with respect to stability, fragmentation and abrasion, etc. would enhance the long-term equipment design process at the vendor level, and provide the end user with improved short-term operational guidelines and long-term strategies for future purchases and operation. Truck vendors recognize that the interaction between operator, seat, frame, suspension, tires and oil sands is unclear, and must be better understood before proceeding to next generation designs. Similarly for shovel manufacturers, the relationship between bucket/dipper motion, carbody, side frame, rollers, track and oil sands follow in the same vein."

Jan 1, 2002

By Martin Nevens

"In 1998, the Iron Ore Company of Canada initiated an aggressive program to improve the performance of its Carol Lake Concentrator located in Labrador City, Newfoundland. This program was termed the Concentrator Upgrade Program. The Concentrator Upgrade Program was a group of initiatives developed with the common goal of improving the overall process and operations of the IOCC Carol Lake Concentrator. The main goal of the program was to increase the annual production capacity of the concentrator from 18.0 million tomes to 21.6 million tomes. This gain in capacity was to be done mainly through improvements in process iron recovery. The target iron recovery value was 80+% versus a historical value of 70%. This improvement in iron recovery would translate to a natural weight recovery improvement from 44% to 50%.The Concentrator Upgrade Program provided the first opportunity in 30 years to make fimdamental changes to the concentrator flowsheet. To accomplish this, several pilot plants were built to evaluate new circuits. AAer 2 years, a new flowsheet was selected for the primary gravity separation circuit and the magnetite circuit. The centrepiece of the new flowsheet was the introduction of Hindered Settling Separators to the metallurgical process.The Concentrator Upgrade Program has since proceeded into detailed engineering and, as of February 2001, construction. The first one of IOCC’s 3 primary AG Mills (Mill 11) has been converted to the new flowsheet at the time of writing and is in the throes of commissioning. This paper will review the flowsheet development program in the pilot plant for the gravity separation circuit and examine the overall benefits to the operation of the IOCC Carol Lake Concentrator."

Jan 1, 2002

By Neo Molelekeng, Jocelyn Bouchard, Rebecca Monnapula, Martin Émond

"Xstrata Alloys – Eland Platinum concentrator (South Africa) has recently been commissioned and is now initiating a challenging optimisation program encompassing the entire operation. Process control improvements are key elements of the program and initial results have demonstrated how leveraging from current assets can bring significant improvements through overall reduction of variability. This paper gives a brief overview of the operations and details how Eland is striving to become a top tier leader with advanced regulatory control strategies recently implemented. Results reveal that what can be achieved in a standard control system (PLC or DCS) should not be underestimated as the first interventions led to a steadier operation of the primary ball mill circuit. Following the improvements, significant and sustained reductions of standard variation were observed for key process variables around their set-point: primary ball mill feed rate (72 %), rougher feed density (58 %), and rougher feed flow rate (47 %). A path forward has been identified to tackle further opportunities around the primary grinding circuit: water balance management, throughput optimisation as well as charge and power draw control.INTRODUCTIONThere are numerous approaches to mineral processing plant optimisation. As the benefits of determining the right reagent types, mix, dosage and addition points, or the proper charge of grinding media in a mill are fully appreciated, there is still nowadays some misunderstanding and misconceptions about process control in general and how it can contribute to the whole optimisation process. The confusion between the various disciplines involved, i.e. instrumentation, control system programming, automation and process control, certainly does not serve the best interest of the industry with this regard."

Jan 1, 2010

By Fernando Romero Lage

"Crushing and screening theory and application has remained fairly consistent in the last 50 years. The application of such equipment is guided by varied formulaic conventions and rules that due to the entropic nature of the process, remains more an art than a science. The variability of conditions creates an environment in which trial and error becomes the principal means of process balance and control. This paper illustrates some of the theories behind the process, plus other assumptions, postulates, myths and misconceptions that exist within the crushing and screening industry.INTRODUCTIONContinuous material balance calculations are habitually performed in the design of new comminution circuits as well as in the valuation of existing circuits. A continuous material balance calculation is one in which the input rate of material is equal to the output rate for each unit functioning in the circuit. At continuous analysis, there is no accumulation or losses of material within the system, as it is when performing a discrete event analysis.In order to produce viable and manageable mine-to-mill material, whether it is ready to leach or ready to mill, we must reduce the material in a series of stages. The power demand increases as the material size decreases, as it is when folding a piece of paper successively. As with the paper, there is a crushing size limitation that is a consequence of the mineral properties such as work index, moisture, viscoelasticity, etc. Comprehensive knowledge of crushing plants in both the aggregate and the mining industries show that, after three stages of crushing, a particle size distribution originating from a blasted deposit can be reduced from an nominal maximum size of 500 mm to a nominal maximum size of 12 mm. if the last stage of crushing is set in closed circuit, the screen openings will be able to yield a smaller top size.Achieving steady and continuous material balance poses major difficulties as crusher lose their settings, screens blind or peg, and material characteristics change geographically or seasonally. Overloading conditions in crushers and screens are nothing but counterproductive, and the net losses of an unbalanced circuit can be overlooked when mining operators are paying a lot more attention to the evermore complex systems downstream.It is not simply the crushing of the mineral but achieving the right size for the downstream milling process that will yield the maximum amount of energy savings."

Jan 1, 2010

By S. Tuttle, R. Sisson

"Suncor Energy Inc. has proposed a 2.2 billion dollar expansion to the current oil sands operation, which will more than double the productive capability of the facility. As part of the application for this expansion, a comprehensive closure plan had to be developed and filed.Closure planning includes a systematic evaluation of the area to be developed, the development activities planned, the goals and objectives of the corporation in re-establishing landforms and ecosystems at the same time as running an effective operation. As early as is practical during the mine development, surface contouring is completed, soil is reconstructed, and vegetation, surface drainage and wetlands are re-established. Once active reclamation is complete and vegetation has been re-established, Suncor monitors maturation of landscapes and ecosystems to provide the submission basis for reclamation certification"

Jan 1, 1999