Search Documents

By M. Dosoudil

"Continuous pressure filtration is a modern process for the mechanical dewatering of flotation concentrates of coal and similar coal slurries. This method will give a lower moisture content than classical vacuum filtration, the improvement lying in the range 5% to 15%. Eighteen coal slurries have been examined in this survey. They are representative of a wide spectrum of filtered slurries. IntroductionDuring the last five years, a number of coal slurries have been tested either in the laboratory or with a pilot plant. The test pressure ranged from one to six bar. The results have been evaluated by mean s of a computer. Determination of the filter capacity and the resulting moisture content and energy consumption has been made with respect to the continuous pressure filter, Amafilter construction-type KDF (Fig. I) . Standard sizes of these filters are 60 m2, 90 m2 and 120 m2.The continuous pressure filter is a horizontal filter with a level tank. Six filter axles are mounted on a rotating main shaft, each with a particular number of elements attached. The elements rotate on their axes and move along a circular trajectory. Periodically the elements submerge into and emerge out of the slurry. A constant air pressure is maintained above the suspension, thus providing the pressure gradient necessary for filtration. The filtrate together with the dewatering air flows through the elements into the hollow axle and out of the filter."

Jan 1, 1987

By A. Mellek, M. Pischtschan, M. Perrucci

ABB has received an order for one of the most challenging mill drive projects in its history. With one SAG mill and one ball mill to be added at an iron ore mine in Sweden, the customer’s plant managers wanted to have the most efficient solution for driving their mills but had the budget limitations typically faced by the majority of mining companies during periods of market downturn. To find the best balance between cost of acquisition and highest performance throughout the lifetime of the plant, ABB was selected to deploy a synchronized bypass solution, in which only one drive system is used for two different mills in series. However, being one of the first grinding mills in the world with such a solution was not the only challenge the ABB team faced: The inclusion of some mill application functions - e.g., frozen charge protection, automatic positioning and creeping mode - brought the demands on the engineers to another level. With only one frequency converter and one mill application controller available, the configuration logic and interlocks had to be meticulously designed and thoroughly tested to ensure a smooth and safe startup. The solution offers a footprint reduction and more operator flexibility at a reduced investment as each mill can be run in both directions, and wear on the mechanical components can be greatly reduced due to ABB’s premium ring-geared mill drive (RMD). This paper will describe the details of the project, the configuration developed and the tests performed to guarantee correct software functionality. Mill startup is scheduled for January 2016.

Jan 1, 2016

By S. H. Schulz

100 YEARS AGO, on the first of August, 1877, the mining engineer Friedrich Koepe was granted the patent rights for a hoist driving ropes on the principle of friction. It was named after him: the Koepe hoist. On the occasion of this centenary, the main features of the Kcepe principle are described.

Jan 1, 1977

By S. Pietruszczak, G. Su, T. S. Nguyen, E. Haghighat

"In this paper, the mechanical properties of Tournemire argillite are modeled using a mathematical framework which employs the microstructure tensor approach (Pietruszczak & Mroz, 2000). The experimental data incorporates the results of a series of triaxial tests (Abdi & Evgin, 2013) conducted at different orientation of bedding planes relative to the direction of loading. First, a plasticity framework is presented which involves the specification of the conditions at failure as well as the description of the irreversible deformation process. Later, a systematic procedure is outlined for identification of material functions/parameters involved. The paper is concluded by presenting the results of numerical simulations of the triaxial tests. It is demonstrated that the model can adequately reproduce the primary effects of anisotropy in the stable deformation regime as well as the onset of fracture.INTRODUCTIONThe understanding of the mechanical behaviour of argillaceous rocks is important in many types of geotechnical projects, including petroleum extraction, carbon dioxide sequestration as well as deep geological disposal of radioactive waste. In all these cases, the primary concern is the onset and propagation of damage due to excavation, transport of pore fluids and/or elevated temperature. The Canadian Nuclear Safety Commission (CNSC), Canada’s nuclear regulator, will be responsible for the licensing of future deep geological repositories. In order to evaluate the safety of deep geological repositories, CNSC staff keep abreast of scientific developments by collaborating with national and international partners on experimental and theoretical research on the long-term performance of those engineered and natural barriers. Through that collaboration, the CNSC has access to data resulting from experiments performed at different Underground Research Laboratories (URL). Such an URL is situated in Tournemire, France, in an argillaceous rock formation, the Tournemire argillite. The Tournemire argillite is characterized by the presence of closely spaced bedding planes and exhibits a strong anisotropic behaviour, so that its strength as well as deformation properties are directionally dependent."

Jan 1, 2015

By W. M. Moon, Hugh G. Miller, C. -S. So

"Digital image processing and enhancement techniques have been applied to airborne gamma ray spectrometry data from Sudbury, Ontario. These results have been correlated and compared with the available geological maps to evaluate their usefulness for identifying lithological units. Digital processing allows the correlation of various data sets, and different combinations of images can be tested and viewed as a composite image. Composite images with pseudocolours provide an opportunity to analyze and correlate information that is not otherwise apparent in individual images. Principal component analysis has been applied to the gamma ray spectrometry data to evaluate their efficacy and relative information contents of the measured and computed data. The results of this study indicate that the combined radioelements image (obtained by combining the radioelement image and the ratio images) is effective for defining areas of relative concentration of a specific element in near surface materials. Furthermore, the composite radioelements image (produced by combining three separate radioelement images) and composite principal components image reflect large-scale lithological variations. IntroductionThe Sudbury area is a unique geological structure located in the southern Canadian Shield (Fig. 1). Because the area hosts economically significant nickel-copper deposits (Pye et al., 1984), it has been surveyed in great detail by geological and geophysical methods. In order to obtain meaningful geological infonnation about the Sudbury area, several studies have been carried out with the application of innovative mathematical techniques for geophysical modelling, and attempts have been made to integrate the multisensor geophysical data available for the area (e.g. Gupta et aI., 1984; Moon et al., 1988; Singh et al., 1993). The main objective of this paper is to apply digital image processing and enhancement techniques to airborne ganuna ray spectrometry data in order to determine their usefulness for regional geological mapping."

Jan 1, 1994

By H. E. Lake

VERY EARLY in the initial stages of underground development work at Eldorado's Beaverlodge operation, the decision was made to use mill tailings as a backfill product. Mining and milling commenced in June, 1953, using locally available sand as backfill, while test work and installation of a plant was carried out to prepare ?and deliver the tailings to the mining areas. The first use of tailings was made in February, 1954, a sandslime separation being carried out with hydraulic cyclones. To date (January. 1956), approximately l 40,000 tons of fill have been used in the stoping areas, providing very effective support in a 50 deg. Vein system of cut-and-fill mining. The recoverable portion of the mill tailings amounts to 40 to 45 per cent, which has resulted in a product giving a percolation rate of 6 to 10 inches per hour. Owing to the fact that Eldorado has milled from 15 to 2 5 per cent more ore than it has mined, through the purchase of custom ore, the degree of control on the sand-slime separation has not been as critical as it might normally be when the filling operation must depend only on the tailings from ore mined. A description of the conditions involved and of the plant as finally installed is given below. It might be mentioned here that, with the impending increase in milling capacity from 700 tons to 2,000 tons p.er day, the present plant will be considerably altered within the ensuing year to handle the increased tonnage and distribution.

Jan 1, 1956

Partnership with MiHR ? AHRC and MIHR jointly developed Mastering Aboriginal Inclusion for Mining ? Customization specific to mining Mining is unique? ? History of Aboriginal peoples and the land ? Unique community needs ? Effects of Impact Benefit Agreements ? Remoteness of mines ? 1200 Aboriginal communities located w/in 200km of active mines or exploration ? Long term effects of the land

May 1, 2009

By T. Gonzales, M. Maleki, M. Caçador, B. Climenhaga, H. Ghorbani

The campaign life of furnaces in the copper making industry is greatly affected by damage caused by normal operation cycling and abnormal conditions. Proper monitoring and assessment of the existing conditions and safe remaining life of the vessels and their refractory lining is key to prevent an unplanned early replacement. This paper presents an industry-proven refractory management program as well as a typical fitness-for-service assessment of a rotary vessel shell in order to extend the campaign life of copper making furnaces and enhance safety. The furnace refractory management system involves a comprehensive audit and monitoring program which has been successfully applied to several copper flash smelting furnaces over the past 15 years. The fitness for service assessment provides a methodology to estimate the remaining life of the steel components by evaluating the existing damage and future damage rate based on the historical survey data. The above practices can provide the operator with cost savings by extending the vessel campaign life in lieu of implementing more rigorous refractory lining and shell audits. INTRODUCTION Primary copper smelting is generally divided into two categories of flash smelting and open bath smelting. There are many different types of vessels that can be used to convert the copper concentrate to blister copper including, flash, Mitsubishi process, TSL (ISA/Ausmelt), SKS Bottom Blowing, Anode and Teniente/Noranda furnaces, reactors, and Peirce Smith converters. Each vessel has its own complex and intense environment which requires careful refractory and steel design to withstand the severe thermomechanical and thermochemical attacks within its campaign life. The campaign life of furnaces is greatly affected by damage caused by normal operation cycling and abnormal conditions. Proper assessment of the existing conditions and safe remaining life of the vessels and/or refractory lining is key to prevent an unplanned early replacement. This paper presents an industry-proven refractory management program as well as a fitness-for- service assessment methodology to estimate the remaining campaign life of copper making furnaces resulting in cost savings and enhanced safety of the operating vessels.

Jan 1, 2019

By MacKenzie Dickson

"INTRODUCTIONGold is found in many natural states, native nuggets, loose grain in river sands, veins in rock, as well as associated with sulphides, oxides, etc., disseminated more or less minutely.Its high value in recent years has spawned new technologies to win values from sources once considered too lean for commercial recovery. Cyanide leaching from fine milled ore or tailings, from upstream recovery operations, coupled with adsorption onto relatively coarse granules of activated carbon, concentrate the gold enough to be converted to bullion by time-honoured methods.The carbon granules are fragile. Size degradation in handling must be minimized not only to prevent loss of gold on fine fragments of carbon that could pass with the barren tailings, but to maintain adsorption efficiency. Besides, the granulated carbon itself is costly. Circular Vibroscreens are winning acceptance for dewatering carbon granules thanks to their gentle yet effective performance in gold recovery systems around the world. The system at Equity Silver is illustrative.BackgroundEquity Silver Mines Ltd., Houston, British Columbia, first began production in September 1980. In 1984, a feasibility study showed that additional gold and silver could be economically recovered through cyanide leaching of the flotation tailing.Although the carbon-in-pulp (ClP) or carbon-in-leach (CIL) process is commonly used for extracting precious metals from slurries, the use of circular vibrating screens, and Vibroscreens in particular, for the carbon circuit is an innovation that cuts costs.Rectangular vibrating screens have been the conventional separation mechanism of choice across North America. In contrast, the use of Vibroscreens has been proven to be less costly for the initial purchase and installation. Also, these circular vibrating screens require less power and less space. A description of Equity Silver Mines' process shows how these screens have been successfully integrated into the system."

Jan 1, 1989

By R. K. Sidhu, N. L. Richards, M. C. Chaturvedi

Nickel base superalloy IN-738LC, strengthened mainly by the precipitation of y' phase, is extensively used in hot sections of land-based and aero gas turbine engines. Fusion welding, which is one of the most commonly used joining techniques for the repair and fabrication of superalloy components, however, finds a very limited application in case of IN-738LC components, as the alloy suffers from HAZ cracking during welding and during subsequent postweld heat treatment (PWHT). The present paper reports on the two methods studied to reduce the HAZ cracking in as-welded and postweld heat treated GTA welded IN-738LC, viz., the use of various fillers during welding, and the use of appropriate heat treatments prior to welding. The results of the microstructural analysis and crack measurements indicated that the HAZ cracking in GTA welds of IN-738LC was significantly reduced by using age-hardenable fillers with Al+Ti concentration less than that in the base metal in conjunction with a preweld heat treatment developed by the authors.

Jan 1, 2006

By Rodrigo Serna, Nora Schreithofer, Zoltan Javor, Kari Heiskanen

"Mineral floatability is a function of mineral properties such as size, liberation, shape, surface composition, reagent coverage on the surface, level of oxidation on the surface, etc.; pulp chemistry: Eh, pH, temperature, DO, reagent type, etc. and hydrodynamic conditions: turbulence, gas dispersion, D32, etc. The biggest challenge with predicting the floatability of an ore is finding a measurement method that would take into account the effect of all of the variables on the floatability of the minerals. The particle-bubble attachment time measurement is considered as an alternative way to predict the floatability of minerals instead of using expensive and time consuming flotation tests because it takes into considerations both surface chemistry and hydrodynamic parameters present in the froth flotation. The existing particle-bubble attachment time method is suitable for studying some significant flotation variables such as pH, temperature, particle size, reagent type and concentration. Nevertheless, measuring the attachment time as a function of collector coverage or surface oxidation is much more challenging. This paper introduces a new induction timer designed to measure the effect of galvanic interaction on the attachment time of particles. The new setup employs an array of needles to create 6 bubbles with the average size of 2.1 mm. Imaging system is used to set the initial distance between the particle bed and the array of bubbles. The attached particles are collected and sent for further analysis. One of the main benefits of the new experimental setup is that the attached particles can be physically separated from the unattached particles therefore many of the particle properties can be analysed and evaluated.INTRODUCTIONSchumann (1942), and Tomlinson and Fleming (1963) proposed that the flotation rate constant is dependent on four probabilities: particle-bubble collision (PC), particle-bubble attachment (PA), particlebubble aggregate stability in turbulent environment (PE), and particle-bubble aggregate stability in froth phase (PF). Any change in any of these probabilities will affect the overall flotation rate constant. All of the above-introduced probabilities are influenced by stream- variables and mechanical variables but their extent of influence vary. The stream variables are particle properties that have been shown to affect flotation rate constant such as size, shape, liberation, mineralogical composition, reagent surface coverage, surface oxidation, etc. The mechanical variables are the direct and indirect properties of the flotation unit affecting flotation rate constant such as cell and impeller geometry, air rate, impeller speed, air holdup, bubble size, residence time, hydrodynamics, froth depth, etc. For instance, the probability of collision is affected by many mechanical variables (bubble size, hydrodynamics, bubbles holdup etc.) but only one stream variable (particle size) has a major effect on it. On the other hand the probability of attachment is affected by much more stream variables: particle size, shape, liberation, surface composition, particle surface oxidation and collector coverage, Eh, pH, etc."

Jan 1, 2016

By H. A. Pearse

Introduction This paper may be regarded as another instalment of the story of the Britannia milling operation. From time to time in the past, articles (1) have been prepared by various members of the staff, giving details of crushing, grinding, and flotation treatment for the normal Britannia ore. It is not, therefore, the purpose of the present paper further to discuss what may be termed the standard milling operation, but rather to describe a flotation practice which has been evolved directly as a result of the general depression. The normal Britannia ore mixture contains chalcopyrite and pyrite as the main sulphide minerals, together with minor gold and silver values. The standard milling practice, evolved during several years of experimentation, provided for bulk flotation of the two sulphides after primary grinding to only approximately 35-mesh, followed by regrinding of the bulk concentrate, with subsequent separation of the chalcopyrite and pyrite to make a marketable concentrate of each mineral. However, in the face of a constantly increasing surplus of copper on the world markets and a steadily falling price during 1930 and 1931, it was obviously undesirable to continue producing large quantities of this metal at a loss. On the other hand, Company officials were very reluctant to add to unemployment by closing down entirely, provided operations could be continued without excessive losses. Fortunately, the existence was known of a fair sized body of ore, quite low in copper and relatively high in zinc content, with also a very considerably higher gold value than that prevailing in other sections of the mine.

Jan 1, 1934

By M. Remillard, M. Garon, M. Thérien, D. Hodouin

"Nineteen streams in the copper and zinc flotation units of the concentrator of the Matagami division of Noranda Inc. have been sampled for particle size distributions chemical assays, and gold and silver contents in each particle size interval. The data are upgraded by the mass balance package BILMAT. These results, in conjunction with microprobe analyses, are used to quantify the silver losses in the copper clean¬ing flotation stages and to determine how overall silver and three silver-bearing minerals are recovered in the plant final products.RESUME Dix-neuf produits des circuits de flottation du cuivre et du zinc de la division Matagami de Noranda Inc. ont été échantillonnés pour leur distribution granulométrique, analyses chimiques et le contenu d'argent et d'or des fractions granulométriques. Le bilan métallurgique a été obtenu à l'aide du programme BILMAT. Ces résultats couples avec une etude minéralogique à la microsonde sont utilises pour quantifier les pertes argentifères aux diverses étapes de nettoyage du circuit de cuivre et pour de¬terminer la repartition de l'argent et des trois minéraux argentifères dans les produitsfinals de l'usine.INTRODUCTION The Matagami division of NORANDA INC. produces copper and zinc concentrates from a sulphide ore which contains a small amount of gold (0.34 g/t) and silver (20 g/t). Only a small part of the silver (~-30%) is presently recovered in the copper concentrate. The objective of this study is to evaluate the metallurgical behaviour of silver, and secondarily of gold, in the flotation circuit for a possible increase of its recovery in the copper concentrate to improve its economic value. For that purpose it is worthwhile to study the minerals which bear silver and to determine the critical flotation stages where they are lost in the tails. The methodology proposed here is based on a coupling of a mineralogical study and a detailed mass balance calculation in the flotation circuit."

Jan 1, 1986

By G. Kollberg

"IntroductionThe SALA Caravan Mill system represents a proven concept for the design and operation of mobile and semi-mobile ore dressing plants.The Caravan Mill has been developed to meet the demand for a flexible processing plant to be used for small and medium-sized orebodies or for pilot investigations of deposits directly at the mine site e •The first Caravan Mill installation was put into operation in 1970 and a number of plants have been delivered world-wide since then.The Caravan Mill system has great flexibility both in capacity, ranging from 50 to 1000 tons per day, and in process combinations. The process modules available are:• crushing by jaw and cone crushers;• pre-concentration by the Dyna Whirl Pool dense media system;• grinding by wet rod or ball mills;• separation by gravity, magnetic, flotation or leaching-CVP adsorption methods;• dewatering by lamella or conventional thickeners and vacuum filters.To form complete plants, auxiliary equipment is also available, such as:• bins, feeders and conveying systems;• power generator units;• water tank and pump for process water;• interconnecting piping and cables;• erection and service tool kits;• set of spare and wear parts.For mine sites with rainy or winter conditions, a plastic tent with air heater can be supplied to cover the ore dressing equipment. Each module is workshop assembled complete with slurry pumps, internal pipe work, electric wiring with plug-in connections, hoses, etc., all arranged for quick and simple connection between the units. Before delivery, each unit is tested in the workshop."

Jan 1, 1982

By W. J. Kuit

"Complex facilities which provide for the collection, management and treatment of effluents emanating from the Sullivan mine and concentrator tailings were made operational in October, 1979. Key features of the system are the use of upgraded tailings ponds for the storage of up to 800 million litres of metals-contaminated effluents, a treatment plant employing lime in a high density sludge process and a sludge-impoundment facility designed for maximum long-term environmental safety. The completed works are cap1ble of satisfying a difficult range of operating requirements imposed by highly variable weather conditions, drainage flows and soluble metals loadi11gs. Final capital expenditures for the project will approach $10 million and annual operating costs are estimated at $0.8 million.This paper discusses the Kimberley effluents treatment project and the major considerations in its development. The treatment process, major plant equipment and initial operating experience are also described."

Jan 1, 1980

By G. R. Guillet

"Bricks made from local Paleozoic shales, and floor and wall tiles made from imported clays, both established record production volumes in 1985 and are the strongest segments of Ontario's clay products industries. However, renewed interest in traditional materials also supports a good market for clay flower pots and flu e liners, and innovative processing studies are showing promise for possible new production of clay roofing tiles. This paper reviews the highlights of a comprehensive study of Ontario's clay products industries, completed in 1986. IntroductionFor some years now, Ontario's clay products industries have been unspectacular in their attempt to cope with the recent recession and the impact of alternative materials. But a strong demand for bricks in recent years has done much to dispel the gloom. Bricks, drainage tiles, sewer pipes, flue liners, structural and partition tiles, and flower pots have been commonly referred to as ""heavy"" clay products, and they have been based largely on local clays and shales. To this list might be added expanded aggregate and mineral wool. Clay refractories, sanitary ware, electrical porcelain, art pottery, and floor and wall tiles are not considered heavy clay products, and are commonly made from a variety of ceramic materials, many of which are imported.Production facilities for heavy clay products often began in Ontario as small family enterprises, using whatever clay was available locally to supply the local market with building bricks and other clay products needed for construction. Improved road systems increased the market range for these plant s, and new technology and industry standards resulted in gradual upgrading and consolidation of them as traced in Table I"

Jan 1, 1988

Flotation of a mineral bearing particle is the result of successful completion of a chain of events, such as, producing particles with sufficient exposure of the valuable mineral on the surface, reagent adsorption, suspension of the particle in the pulp, collision of particle with air bubbles and subsequent attachment, ascending to the froth column and transport to the concentrate stream, among others. These sub-processes in turn are affected by the feed properties such as size and density, and process variables such as size of air bubbles, degree of turbulence in the cell, particle/particle interactions etc.. Thus, inefficiencies occurring in any one or more of the above processes will result in inefficient flotation performance. In spite of its dependency on a wide variety of sub-processes, flotation performance is commonly modelled based on first order kinetics using two or three parameter models. As the model parameters may be affected by several of the sub-processes mentioned above, interpretation of their variations and identifying the specific causes is extremely difficult. Of the many factors that influence the flotation performance, liberation information of the particles such as the grade distribution and surface exposure are considered vitally important. In this paper, it has been demonstrated a) how a predictive liberation model may be derived and used in quantifying the liberation information of the particles produced at various grind sizes and b) how the flotation process may be modelled by explicitly incorporating the liberation information, thereby improving the accuracy of the model. Comparisons of the observed data with the proposed model and those of published liberation/flotation models have also been made.

Jan 1, 2016

By W. A. Crosby, W. K. Smith, K. L. McDonald

"IntroductionThis paper describes how the introduction of two blasting techniques and the resuItant development of new dragline digging methods have increased the productivity of single- and double-seam dragline operations at the Rietspruit opencast mine.LocationRietspruit , one of South Africa's largest opencast strip mines, is situated some 11 5 kilometres east of Johannesburg in the Witbank coal field.BusinessRietspruit is a joint venture between Transvaal Consolidate d Land and Exploration Company (T.C.L.) and Shell, South Africa. Rietspruit is administered and managed by Rand Mines, the Mining division of Barlow Rand, transportation and marketing being the responsibility of Shell. The total saleable coal product, approximately 5,5 million tons per annum, is exported via Richards Bay.Presplitting and Throw BlastingPresplitting was initially introduced in September 1980, as a means of dewatering t he overburden and mid burden to facilitate the use of dry-mix explosives a s opposed to slurry explosives.The utilization of the throw blasting technique arose as a direct result of observed ground movement after the successful introduction of presplitting. The first trials commenced in March 1981 on the double-seam operation. The methods, economics and resulting advantages are fully described elsewhere. A brief description follows.Method of PresplittingAfter determining the desired presplit line, 250-mm holes are drilled to top of coal at 4-m to 6-m intervals, dependent on the competency of the rock overlying the coal. A single 60-kg charge of slurry explosives is located at the bottom of each hole, no tamping is used and all the holes are detonated simultaneously. The results are a competent, straight, vertical highwall. This enables accurate control of the first row of blast holes closest to the highwall, which is a prime requisite for successful throw blasting."

Jan 1, 1983

By Gautier Njiekak

The current study provides an experimental approach that aims at documenting the effects of different phases of CO2 (gas, liquid, supercritical fluid) on rock seismic responses. This has implications on obtaining quantitative estimates of fluid saturations for geological storage. The ultrasonic pulse transmission technique is the underlying methodology used in this work. Unlike previous rock physics studies involving CO2 as pore fluid, care is taken to fully saturate the studied samples and also to separate pore fluid effects from pore pressure build-up effects during the experiments. This allows to record seismic effects that are solely reflective of changes in the pore fluid properties. Measurements were done on a CO2 saturated Berea sandstone. Laboratory results show P- and S- waveform variations (velocity, amplitude) in response to CO2's varying phase state. Overall, CO2 phase changes (gas to liquid and gas to supercritical fluid) are marked by a drop in velocities, with the drop being smaller and less immediate over the gas-supercritical fluid transition than over the gas-liquid transition.

Jun 1, 2012

By M. Niinae, F. Nakahara, T. Kawamoto, T. Suzuki

"MgO was chosen as an As(V) immobilization agent and a series of immobilization experiments was performed to obtain insights into the behavior of As(V)and MgO during leaching tests. Our experimental and modeling results demonstrated that As(V) immobilization by MgO consists of the following steps: (i) an increase in soil pH, (ii) desorption of As(V) from the soil, and (iii) the re-immobilization of As(V) by MgO/Mg(OH)2particles. Regarding the behavior of MgO, the modeling results showed that when the MgO dosage was 25 mg MgO/4g-drysoilor less, the majority of MgO was used to increase pH, and less than 1% of MgO was used to sorb As(V), which was consistent with the result of leaching tests showing that a high level of As(V) was leached at the MgO dosages. On the other hand, when the MgO dosage was above 25 mg MgO/4g-drysoil, the percentage of MgO used for As(V) sorption increased up to 35%, and correspondingly, the As(V) leaching level decreased to below 0.01 mg/L As at an MgO dosage of 75 mg MgO/4g-drysoil.INTRODUCTIONOne of the major arsenictransport pathways causing groundwater contamination is the migration of arsenicfrom artificially or naturally contaminated surface soils. Therefore, in this study, the immobilization of arsenate (As(V)) in soils was investigated using commercial-grade magnesium oxide (MgO) as a potential cost-effective measurement to prevent the occurrence of groundwater contamination with As(V).With respect to the use of MgO for remediating As(V)-contaminated environmental media, MgO has been used in several studies to remove As(V)from water(Yu et al., 2011; Jia et al., 2013; Tresintsi et al., 2014). Although these studies demonstrated that MgO effectively removes As(V)from water in water-MgO systems, the behavior of As(V)in water-soil-MgO systems has not been evaluated in the literature, and several questions remain to be answered to comprehensively evaluate the use of MgO as an As(V)immobilization agent in soils. For instance, as is well-documented in the literature(Ford, 2002; Lenoble et al., 2002; Zeng et al., 2008), iron oxy-hydroxide (FeOOH) is one of the important adsorbents for As(V)in both natural and engineered systems. Therefore, it is anticipated that the presence of FeOOH in soils significantly influences the behavior of As(V)in water-soil-MgO systems and consequently, the immobilization performance by MgO. Another important question to be answered is the behavior of MgO during the immobilization treatment. In our previous studies (Suzuki et al., 2013a, 2013b), commercial-grade MgO was demonstrated to effectively immobilize lead and fluoride, and the immobilization effectiveness was indicated to last more than 100 years against the exposure to acid rain (pH 4.0). However, these studies focused on the behavior of contaminants. As a result, little is known about the behavior of MgO during the immobilization treatment. The lack of understanding of the behavior of MgO during immobilization treatment is one of the main concerns leading to relatively low public confidence in immobilization treatments."

Jan 1, 2016