Search Documents

By M. Normandin

The performance of various polymers and other macromolecules used to flocculate red mud particulate materials in the Bayer process can be evaluated on the basis of their efficiency to achieve adequate settling velocity and turbidity level, The Jar Test is widely used in the mineral industry to determine the efficiency of solid-liquid separation processes, particularly for gravity settler of the Bayer process. However, a high level of variability is found in the data obtained by this methodology, In this study, different parameters of the cylinder test procedure are evaluated to determine their role in the overall variability of the method, As demonstrated by laboratory testing, the overall variability can be considerably reduced by good laboratory practices.

Jan 1, 2005

By G. A. Gillett, C. F. Bonney

"The Davy McKee combined mixer-settler (CMS), is a liquid-liquid contactor, which has been commercially applied to the recovery of uranium from dilute sulphuric acid-bearing leach liquors. CMS differs from most other solvent extraction systems in that the mixing and separation of the phases is carried out in the same vessel.IntroductionTypical solvent extraction plants for the recovery of uranium operate at organic to aqueous feed flow ratios of 1 : 2 to 1 : 30. Because it is beneficial to mix the organic and aqueous phases at an organic/aqueous (O / A) ratio of between I : 2 and 2 : I there is incompatibility between the over-all and operating O /A ratios.Conventional mixer-settler designs require an external recycle of the minority flow which results in the possibility of over-mixing, increased settling requirements and entrainment losses. Other workers have approached this problem in terms o f enhanced sett ling and this has been partly successful.Davy McKee's approach involved a radical rethink of the principles of liquid-liquid contact and separation.Description of CMSThe CMS has the important advance that the required mixing O/A ratio can be achieved without external recycle and is not affected by the O /A ratio of the feeds. Three zones co-exist within the CMS unit-a central mixing zone and upper and lower separation zones. A pump impeller on a draught tube is installed within the mixing zone and baffles are installed above and below the mixing zone. Conventional mixer- settlers have several undesirable features which ca n largely be eliminated using the CMS system:"

Jan 1, 1983

By Shanjun Mao

This paper summarizes current achievements of Digital Mining in China, puts forward the concept, framework and key technology of Smarter Mining, and finally points out that there is still a long way to go in order to acheive Smarter mining.

Aug 1, 2013

By M. Leijd, K. S. Forrester, M. Saxon, M. Oczlon

This paper provides an introduction to wet high intensity magnetic separation (WHIMS) and its successful application to the beneficiation of rare earth element (REE) enriched eudialyte. The analysis includes an in-depth reporting of the deportment of key elements as well as a statistical interpretation of the relative importance of operational parameters including magnetic field intensity, flow velocity, and matrix loading density. Conclusions are drawn on the relative success of the technology, potential areas for process improvement, and the research direction that continues to be investigated. Three original equipment manufacturer (OEM) technologies were subjected to a series of screening and characterization tests to identify the optimal operating parameter set to magnetically beneficiate eudialyte from Norra Kärr, Sweden. Upon the completion of the characterization test it was apparent that the Metso HGMS technology was superior with respect to REE recovery and gangue rejection for the Norra Kärr composite. The Metso HGMS was then subjected to a series of verification tests to confirm the repeatability and reproducibility of the system.

Jan 1, 2014

By K. Nagai

The Asian projects are now in their second terms after the five-year first terms. Ultrafined-grained steels were developed in lab-scale and/or in practical process. Basic approach has been performed to explore the evolution mechanisms of ultrafine-grained microstructures. There have been investigated two approaches to make the ultrafine grains: the "recrystallization route" and the transformation route. In the "recrystallization" route, heavy deformation at low temperature is necessary for the ultra-refinement. In the transformation route, making the high density of ferrite initiation sites in the deformed austenite, especially of the heavily compressed austenite structures, is essential for the ultra-refinement, and further hindering the ferrite growth is also inevitable to utilize the high initiation rate. Strength and toughness are dramatically improved by the ultra-refinement. Fatigue property is also excellent. The poor uniform elongation can be enhanced by the design of the second phase dispersion. At the same time the application has been also pursued from various viewpoints of engineering to take advantages of the ultrafine-grained steels. Bridge, ship, construction, automobile and other high strength parts are being attempted for the application.

Jan 1, 2004

By J. Lu, D. B. Dreisinger, G. Houlachi

"Zinc metal is primarily produced by electrowinning from sulfate solution. Zinc electrowinning is very sensitive to impurities such as Co and Ni. These impurities have to be removed to produce high-quality zinc and maintain a high zinc current efficiency. Zinc dusts are used to remove these impurities by cementation. However cobalt cementation is extremely slow and it is typically activated by the addition of Cu and Sb. Even with the use of Cu-Sb activation, cobalt is still difficult to remove. The zinc dust used for cobalt cementation is negligible compared to that consumed for hydrogen evolution. In some plants up to 6-7% of electrolytic zinc is used for cementation. This is a great waste of energy. Cu-Sb activation is not well understood. The objective of this study was to further understand the Cu-Sb activation and then find a way to reduce hydrogen evolution and promote cobalt cementation. The investigation reveals how hydrogen evolution (or zinc dissolution) and cobalt cementation and re-dissolution change with temperature, zinc dust dosage, the concentrations of copper and antimony and time. In the Cu-Sb activation, copper is deposited on a zinc particle to produce a porous shell. The zinc particle as an anode dissolves while the shell as a cathode provides a place where cobalt cementation and hydrogen evolution occur and they are catalyzed by antimony. A certain level of antimony (around 0.1 mg/L) is a key to maintain the catalytic effect of the shell. At a higher antimony concentration, cobalt cementation is accelerated slightly while hydrogen evolution is increased greatly. When a zinc particle dissolves to a certain degree, cobalt loses its cathodic protection and starts to re-dissolve. The change in cobalt concentration is determined by the rates of cobalt cementation and re-dissolution. The operation conditions can be optimized to maximize the cobalt removal and minimize the zinc dust dosage.INTRODUCTIONMost of the world’s zinc metal is produced by electrowinning from sulfate media. Many impurities such as iron, copper, cobalt and nickel are co-extracted into solution with zinc. Iron, mercury, indium, lead and tin are removed by co-precipitation as hydroxides. Copper, nickel, cobalt, aluminum, arsenic and germanium are partially co-precipitated with iron while cadmium, magnesium and chloride remain in solution. Cobalt, copper, cadmium, nickel and etc. are subsequently removed by cementation with zinc dust to achieve an acceptable current efficiency and high purity metal product for the economical production of zinc. Zinc provides a strong thermodynamic driving force for the cobalt cementation:"

Jan 1, 2016

By B. L. Dorey

"Performance management is a systematic, practical approach to managing people. It is founded on some basic assumptions about people and is designed to focus on people in the work place. Organizing meaningful information and using it to involve people is a cornerstone of this system.Some common sense practices are developed to involve people in an organization's effort to improve performance. The successful implementation of this program requires solid commitment and total involvement from all levels of supervision and employees for maximum results and lasting impact. All levels of supervision participate in training sessions to tailor the systems for implementation in their areas. This style of management is data-oriented and the bottom line of success is to measurably improve performance. Basic Assumptions about PeopleMost people in an organization, regardless of level, take pride in their work and generally want to do a good job. When performance falls off, there is usually some explanation other than the employee not really caring. People like to know their exact responsibilities and clearly what is expected of them. People like to know where they stand with the boss and would like to be evaluated on what they do and accomplish, rather than on what others think or feel about them. Further, people like to be rewarded for their good results, indeed, to understand what motivates people, we must look at what happens as a result of their actions. Another belief is that supervisors often have a greater influence on the performance of their people than they fully realize. Simply letting people know how important their performance is can have an impact. The Key ElementsGiven these basic assumptions and beliefs about people, some common sense practices have been systematically developed to manage more effectively."

Jan 1, 1989

By G. Guiglionda, A. Deschamps, F. De Geuser, M. Langille, B. J. Diak

"Increased demand for light-weighting in passenger vehicles has created a need for strong, light, ductile materials to be used in body-in-white applications. The AA6xxx-series of aluminum alloys are suitable candidates meeting most requirements but can fall short of the formability demands of designers, necessitating an understanding of what controls the formability in this alloy series. This work examines the effect of copper alloying in AA6xxx on the pre-ageing and natural ageing responses of the microstructure and mechanical properties. The changes in microstructure observed by differential scanning calorimetry and hardness testing are related to the work-hardening and strain-rate sensitivity parameters for these alloys measured by tensile testing. An observed asymmetry in the measured strain-rate sensitivity associated with increasing versus decreasing strain rate changes suggests that a different mechanism operates for the two conditions. It is postulated how this asymmetry in strain-rate sensitivity will impact the necking and ductility behaviour of these alloys.INTRODUCTION The widespread use of AA6xxx series alloys in the form of sheets has provided the need for a more thorough understanding of the complex interactions between composition, processing, resulting microstructure and ultimately, the mechanical properties of the alloys. Conventional industrial practices involve the production of rolled AA6xxx sheet (typically 1 mm thick) to be used for body-in-white (BIW) applications for auto body panels (Hirsch, 2004, 2014). The final metallurgical step prior to the shipment of these panels to manufacturers involves a solution heat treatment (SHT) reverting the ageing products of the alloys into solid solution and the product is then shipped to the customer. During this shipping time and while sheets are waiting to be used, the natural ageing (NA) process occurs whereby the strength of the alloys increases resulting in reduced formability. This can result in a product that is unable to meet the formability demands of the automotive manufacturer. As a result, industry has moved towards performing pre-ageing (PA) treatments to prolong the “shelf-life” of the material prior to it having insufficient formability. Once formed into BIW panels, the parts are then painted and subsequently undergo the paint curing heat treatment which consists of a short period of time at medium temperature, typically 20 minutes at 170–190°C. This short artificial ageing (AA) treatment, known as the paint bake (PB), provides additional strength and improved dent resistance for the material, but reduced formability. The PB result is strongly dependent on the PA treatment performed prior to the forming operation. Furthermore, the addition of copper (Cu) to a base Al-Mg-Si composition is known to increase the alloy’s strength. The goal of this work is to study the effect of Cu on strength, strain hardening, and strain-rate sensitivity (SRS) of these alloys, to understand the strength-formability compromise, for two separate heat treatment schedules; one including and one excluding the PA treatment, both followed by NA."

Jan 1, 2018

By J. -M. Bosgiraud, G. Armand, S. Dewonck, L. Richard-Panot

"The Meuse/Haute-Marne Underground Research Laboratory (URL) is located on the eastern boundary of the Paris Basin. The URL started to be built in 2000 (shaft sinking operations) in the framework of ANDRA’s (French national radioactive waste management agency) research program aimed at determining the feasibility of a reversible deep geological disposal of high-level and intermediate-level long-lived radioactive waste (HLW, IL-LLW). Its underground drifts are used to study the Callovo- Oxfordian claystone layer between 420 m and 550 m in depth.The ongoing research program (started in 2006) following the “Technology Readiness Level” (TRL) Scale is more dedicated to technologies improvement and demonstration issue of the different disposal components, even if characterization and monitoring studies are still ongoing.In rock mechanics, at the main level of the URL (located at 490 m), construction and evolution of disposal cells of different size are studied for HLW and IL-LLW packages. A step by step approach, started in 2006, is carried out based on comparison of HM behavior of parallel drifts excavated/supported by different construction methods. These various configurations give insight of the influence of construction method on the EDZ extent and evolution and on the progressive loading of the support, which are key issues to design the Cigéo disposal drifts and excavations.The concept of disposal cells studied for HLW consists in horizontal steel lined micro-tunnels 80 m long and 70 cm in diameter. Several campaigns of tests have been carried out since 2009 in order to demonstrate the feasibility of excavating such micro-tunnels and study their behavior under different conditions (with and without back filling the annular gap between the rock and the casing, watertight or not casing). A full scale demonstrator representative of the benchmark concept has also been excavated, to study its behaviour under thermal loading with heat produced by electrical heaters."

Jan 1, 2015

Heap leaching accounts for around 20% of the global production of copper. In heap leaching coarsely crushed ore particles are contacted with an aqueous lixiviant percolating through large packed beds (heaps) of the ore particles, with the loaded solution collected at the foot of the heap for metal recovery, solution make-up and recycle. While dominant for copper oxide acid leaching, it finds application also in copper sulphide (bio) leaching. Despite their apparent simplicity, heaps are in fact complex chemical reactors in which a number of competing sub-processes determine the overall rate of metal extraction. Therefore, meaningful prediction of copper production rates from heaps, as well as operational optimisation and control, all hinge on a comprehensive and quantitative understanding of these complexities. The paper gives a comprehensive overview of the various sub-processes in copper heap leaching and their interactions, including those relating to mineral-particle-solution-gas phase interactions at the micro-scale bulk transport and distribution of solution in unsaturated dense beds at the macro-scale. On the basis of a more fundamental understanding and modelling, the potential for optimized operation offers new opportunities for the extraction of value from both low-grade and complex polymetallic ores. INTRODUCTION Heap leaching is one of the percolation leaching technologies, which includes in situ leaching, dump leaching, heap leaching and vat leaching (Bartlett, 1998). The common phenomenon in all these technologies is the transport of leach solution through a fixed bed of ore particles, which interacts with the solid as it migrates along its path. The target minerals are released into solution and with its flow are carried out of the bed. The targeted dissolved metal species are recovered from solution through various hydrometallurgical techniques, especially solvent extraction (SX), before the barren solution is returned to the leach process. Heap leaching is practised in three main types of applications: sulphuric acid leaching of copper oxide ores, cyanide leaching of gold ores as well as the oxidative acid leaching of secondary copper sulphide ores, usually with the assistance of certain microorganisms and, more recently, in the presence of chlorides (CaCl2, sea water). While gold heap leaching dates back to the 1960s, large scale copper heap leaching commenced in Chile from the 1980s, and sulphide heap leaching emerged essentially as a consequence of acid leaching from mixed oxide/sulphide ores from the 1990s (Watling, 2006).

Jan 1, 2019

By H. T. John

"The objective of this paper is to demonstrate how the optimum cut -off grade can be calculated for typical large tonnage openpit mines. In the examples, it is assumed that the concentrator tonnage is fixed and that there are no market restrictions. The mining rate is assumed to be variable. This is usually the situation at an operating property.ModellingA model of the ore body is required to examine alternate cutoff grade strategies. The model must be accurate in its relationship between grade and tonnage. Table I shows a typical relationship between ore tons and grade for various cut-off grades. The average strip ratio is also shown. For higher cutoff grades, the ore tonnage is decreased and the ore grade is increased. Strip ratio increases with the cut-off grade.Using the relationship between ton s and grade, and assuming a homogenous, long life orebody, a simple calculation of the optimum cut-o ff grade can be made. The objective is to maximize the present value of cash flows. For the long life homogenous orebody example this objective is satisfied by maximizing present cash flows.Cash flow is calculated by subtracting operating cost from revenue . Operating cost will increase with the cut -off grade as the strip ratio increases."

Jan 1, 1985

By G. Lafont

Aug 1, 2013

By Malcolm R. Gent

"The presence in Saskatchewan of sixteen kimberlite pipes of probable late Albian age has been reported. An abundance of aeromagnetic anomalies possibly attributable to kimberlite pipes have been identified and it is anticipated that industry has acquired reasonable proof of the presence of more than seventy k imberlite pipes in Saskatchewan. Historical reports of diamonds, the discovery of kimberlite pipes and these aeromagnetic anomalies indicate the Phanerozoic Basin and some parts of the exposed Shield in Saskatchewan have an excellent potential f or the occurrence of economically exploitable diamond deposits. The presence of some igneous minerals found in some salt solution breccias also indicates the probable occurrence of extensive diatreme activity during the Devonian.A Laramide Orogeny-induced crustal hinging or arching of the eastern margin of the Phanerozoic Basin and probably dextral wrenching-induced arching and faulting within the basin are proposed as major factors in the emplacement of Cretaceous or younger kimberlites. Zones of crustal weakness between subcratonic Archean blocks and internal faults are also thought to be significant controlling factors in the location of kimberlites in Saskatchewan.Mapped aeromagnetic anomalies interpreted as being possibly due to kimberlite pipes generally tend to be concentrated in, areas underlain by a basement of or with components of Archean age. Within Saskatchewan, these anomalies occur within the probable Trans-Hudson Orogen zone; the Rae-Hearn Craton margin; and the northeast flank of the Elkpoint Basin. Recognized areas of potential f or kimberlite emplacement are the Phanerozoic basin margin, the western limit of the Superior Province adjoining the Churchill Province, and a swath approximately 150m wide along the northeast-southwest trending Shaunavon linear and other areas of inner basin arching."

Jan 1, 1992

By Liangtian Liu, Tie Ou, Guangqiang Li, Chenghuan Yu

For stabilizing the production of containing nitrogen steels, a study on nitrogen absorption behavior of killed molten steel has been carried out by means of the RH vacuum device in which nitrogen was used as a driving gas. The results showed that there was an increase of nitrogen content in molten steel under vacuum processing but the rate of nitrogen absorption was slowed down by the surface active elements. Therefore, a kinetic equation for nitrogen absorption of molten steel with apparent first order reaction was derived by constructing a modified model in which the adsorption of closed surface site was taken into account. The experimental results confiimed that the calculated values agreed with the observed ones. This model is suitable for the prediction of nitrogen adsorption operation for containing nitrogen steels.

Jan 1, 2004

By J. Font

New approaches for the fire refining process of blister copper have been carried out at the Codelco Norte Smelter. These have been mainly focused on modification and improvement of the process configuration based in fluid-dynamic and metallurgical studies of the oxidation and impurity treatment stages. This paper presents the results of the laboratory simulations and industrial tests performed in the 250 t anode furnace, evaluating two different process configurations: ? Bottom Bath Agitation System in the vessel during the oxidation stage, ? Dual Flux Injection System during the impurity treatment stage. The results show the possibilities of effective removal of high content of sulfur from the melt during the oxidation stage by using the bottom bath agitation. The use of the dual injection system demonstrated the significant improvement in the removal efficiency of impurities. Cu2007

Jan 1, 2007

By F. Flores

With the World Summit for Sustainable Development planned for 2002 in mind, nine of the world's largest mining companies decided to initiate a project to examine the role of the minerals sector in contributing to sustainable development, and how that contribution could be increased ? the Mining, Minerals and Sustainable Development Project (MMSD). This project assumed from the start that sustainable development could provide a useful framework to guide the minerals sector which main goal was integrating economic activity with environmental integrity, social concerns, and effective governance systems. The broad steps of MMSD project strategy can be grouped into four major categories: increase understanding of sustainable development; create organizational-level policies and management systems for implementing the principles of sustainable development; collaborate with others with common interests to take joint steps towards sustainable development, and; increase our ability to work towards sustainable development at the local, national, and global levels. In opinion of the article's author, to go ahead with the MMSD strategy and achieving the sustainable development objectives, it is necessary to consider the concept of self-organization, fundamental of the emergent new scientific paradigm, and the consequent epistemology and values that conform a supporting culture for sustainable development.

Jan 1, 2007

By Patrick J. Williams

Defining Features of IOCGs ? Sulphur-poor Cu-Au(-Fe) deposits ? Contain low-Ti iron oxides ? Hydrothermal origin (breccia, vein, replacement) ? Local structural controls (no ?causitive? intrusions) Common Features (Economically-Significant Terranes) ? Regional space-time association with plutons ? Association with widely metasomatized crust ? Na ? Na-Ca ? K ? Variable enrichment in F, Co, Ba, LREE, U ? Little hydrothermal quartz (cf. porphyry deposits)

May 1, 2006

By A. Henk, C. M. Aruffo, K. Fischer

"Geomechanical reservoir modeling offers a valuable tool to predict tectonic stresses, in particular the local perturbations in orientation and/or magnitude which occur at lithological boundaries and faults. The paper presents a workflow for building and calibrating such geomechanical models. The numerical simulations are based on the Finite Element method and can range from field-scale models to smaller, highly detailed submodels of specific fault blocks. The approach considers the reservoir-specific characteristics with respect to subsurface geometry (lithostratigraphic boundaries, faults), mechanical properties and ambient stress field. During the subsequent calibration stage calculated stresses are compared to stress data actually observed in borehole data. Poorly constrained input parameters are iteratively modified within reasonable limits until a satisfactory fit between calculated and measured stresses is achieved. This validated model can then be used for stress predictions between wells and in undrilled parts of the reservoir, respectively. The workflow is applied to two case studies - a large gas field in Northern Germany and a CO2 sequestration project in Australia – to test and illustrate its practical value. INTRODUCTIONDetailed knowledge of the tectonic stress field is crucial for the optimal exploration and use not only of conventional and unconventional hydrocarbon reservoirs, but also for deep geothermal reservoirs, carbon capture and storage (CCS) projects as well as underground mining and nuclear waste repositories. Any reliable stress prediction is hindered by the observation that the magnitude and orientation of the stress field can vary significantly – not only in time, but also in space. Such spatial stress variations comprise all scales, i.e., from the scale of lithospheric plates down to the grain-scale. On the reservoir- and fault blockscale, the local stress field can be influenced by faults and different mechanical properties of lithologies (Sassi & Faure, 1997). The resulting variations in stress magnitude and/or stress orientation are commonly referred to as stress perturbations and give rise to a unique, reservoir-specific stress pattern (Yale, 2003). Thereby, local stress fields can deviate by up to 90° in orientation and several tenth of Megapascal (MPa) in magnitude from regional trends."

Jan 1, 2015

By J. E. Udd, L. B. Geller

"Responding to requests by the Canadian mining industry and the mine regulatory authorities, the Canada Centre for Mineral and Energy Technology (CANMET) undertook a major research project on evaluation of wire rope testing in 1986. The objectives were to document, analyze, and clarify - in basic operational terms the reasons for ongoing mine shaft wire rope failures that occur despite mandatory non-destructive testing (NDT) with electromagnetic (EM) instruments on a routine basis.The project's investigative scope and depth was unprecedented. It could not have been successfully completed without the wholehearted cooperation of industry, research organizations, and mine-inspectorates at both national and international levels.The project's goals were attained. II was shown that, at present, the problem areas in Canada are oj a human , rather than of a hardware-related nature. Consequently, the principal recommendations are concerned with a more widespread, more uniform and thorough operator training and certification process at industrial and regulatory levels. Secondary suggestions concern areas of hardware-related improvements.In this paper an up-to-date general overview is given of the major project results. A n extensive reference list is also provided of papers that contain all relevant documentation in detail."

Jan 1, 1992

By Michael Bowker

Au/TiO2 catalysts were prepared by incipient wetness impregnation and tested for the room temperature photocatalytic reforming of methanol in aqueous solution. These catalysts proved to be more active, on a molar basis, than Pd/TiO2. The dependence on loading of gold was different from that of palladium, showing a double maximum in yield at 0.1 and 2 wt. % with low rate below 0.01% and above 10%. A model is proposed for the reaction involving band gap excitation of titania electrons which are used to oxidise the methanol via adsorbed CO. With palladium, photoreforming of CO and water can be achieved, but this is much less effective on gold, presumably due to the much weaker bonding of CO on Au.

Oct 1, 2003