Search Documents

By J. G. Henning, T. R. Yu, J. E. Croxall

"Test work was carried out to investigate the thermal response of loose and solid rock under varying environmental conditions. The primary interest was to develop a technique that could be used to increase the thermal variation between loose and solid rock for better detectability of loose rock underground with a thermal imaging infrared scanner.A variety of thermal enhancement methods were evaluated both in the laboratory and in the mine environment. Air temperature variation created by the exhaust from diesel driven, mobile mining machinery was studied in detail. When sufficient hot exhaust was supplied to the air, unsteady thermal conditions became more pronounced on the rock surf ace. This allowed a greater percentage of loose rock to be detected by a high-resolution infrared scanner within minutes.The degree of thermal enhancement of loose rock was found to be dependent directly on the thermal conductivity of rock, looseness, air temperature change, and inversely on the size of loose, airflow rate and distance downwind from the heat source. It was also found that an air temperature rise of at least r c, or rock temperature differential of1°C was necessary for minimal thermal enhancement required f or infrared detection."

Jan 1, 1990

By O. E. Humeniuk, A. I. A. Salama, M. W. Mikhail

"Performance testing of prepartion plants is referred to as plant audit. It evaluates plant performance under normal operating conditions and is aimed at improving yield through knowledge of actual process performance and interactions between different processes in a plant.This paper describes the program to evaluate the performance of several Canadian preparation plants. The performance test requires the planning of a sampling campaign that would include all circuits in the plant. Samples are analyzed to determine washing characteristics (screen and float-sink), ash and per cent solids of feed and products of separation units in the plant. Performance characteristics are established based on analysis and material balance. Specific recommendations can then be made to improve recovery, and identify and explain potential causes of apparent deficiencies.The objectives of the program are to reduce the cost of production by improving recovery of clean coal and, in tum, to reduce disposed tailings, establish baseline information on coal preparation plants performance in Canada, and define R&D work needed to optimize plant operation."

Jan 1, 1993

By D. A. Beattie

Talc is a commonly encountered gangue mineral in metal sulfide flotation. Talc is naturally hydrophobic, resulting in high recoveries if polymeric depressants are not used to specifically reject this MgO containing mineral. We have studied the adsorption of a selection of polymers onto talc using a variety of techniques. Adsorption isotherms have been determined using ex situ depletion techniques and in situ ATR-FTIR spectroscopy has been used to determine adsorption kinetics. Adsorbed layer thicknesses have been determined for the polymers on cleaved talc surfaces using the AFM. The effect of the adsorbed polymer layer on the properties of the talc surface has been quantified through contact angle measurements and single mineral flotation tests. Distinct correlations are observed between the adsorbed layer properties and the flotation performance of the polymers. These observations are discussed with reference to the bubble-particle attachment process and the molecular structure of the polymers.

Jan 1, 2006

By Philip M. J. Gray

"The real cost of conversion from ore to semi-fabricated non-ferrous metals has been increasing for many years. Consumer resistance and improved knowledge and techniques now available justify investment in revolutionary as well as evolutionary methods of extraction. Metallurgical factors in current practice which preordain high production costs are identified as: smelters' demand for clean minerals, use of processes with low intensity of working per unit of reactor volume, use of low-velocity reactions, use of long reactor retention times relative to the speed of reactions, dilution of values in solution and commitment to electric power as a source of energy.Six new types of flowsheet are proposed for processing from ore to metal, composed of steps which are economic to construct and maintain and making maximum direct use of fossil fuel and the energy content of minerals. The basic knowledge and technology for developing these flowsheets exists. It is very tentatively suggested that these routes might reduce the capital and production cost for conversion of ore to metal by 30-50%."

Jan 1, 1980

By M. Fafard, F. Chevarin, D. Ziegler, H. Alamdari, M Kavand

"Carbon anodes, used in the Hall-Heroult process, are consumed by the electrochemical reaction to produce metallic aluminum. It is also consumed by parasitic reactions with air and CO2. The carbon anode is made of petroleum coke with different particle sizes, butts (recycled anodes) and coal tar pitch. The mixture of fine particles (less than 150 µm) of coke together with the pitch material forms a matrix, binding the large coke particles together. It is generally thought that the binder matrix is more reactive than the other anode constituents. This conjecture was not clearly proved in the literature. The present study is focused on the CO2 reactivity of binder matrix and anode constituents at 960°C, both under chemical regime (100% of CO2) and under a concentration gradient (diffusion). The apparent reaction rates of these materials were measured. The role of the binder matrix in anode consumption and its disintegration (dusting phenomenon) was discussed.INTRODUCTIONThe metallic aluminum production is one of the most important industries in Canada. The Al metal is obtained by the Hall-Héroult process. The principle of this process is the electrochemical reduction of alumina in molten cryolite carried out by an electrical current between carbon anodes and cathode at 960°C (Equation 1). The carbon anode is typically composed of calcined petroleum coke (65 wt.%) and recycled anode (called also butt, 20 wt.%) with coal tar pitch (15 wt.%), playing the role of cement to ensure the cohesion of the anode block."

Jan 1, 2016

By Akira Fujisaki

"The oil crisis accelerated the change of non-ferrous metals' demand structure. Maturing societies in developed countries and preference for lighter, thinner and smaller products are eroding the non-ferrous metal industries' growth potential. Inventory-control, stockpiling and developing new demand are measures Japanese smelters have taken to cope with the changing demand.The most effective means for risk management of product demand lies in the cooperation between ore producing countries and metal consuming developed countries to assist developing countries in their efforts to ""take-off"", which in turn will bring about a surge of demand for metals.SummaryThe non-ferrous metal industry in the world is suffering its most serious slump since the war. With some of the markets of the advanced industrialized countries approaching saturation point and economized usage of natural resources and substitution growing, the possibility of a quick recovery of the demand for base metals is dim.To cope with the changing product demand Japanese producers have had recourse to such measures as strict inventory control and stockpiling for the purpose of stabilized imports. They have also tried hard for securing raw materials and promoting new field s of demand but the very core of ""risk management"" has been the diversification of line s of business to bolster and stabilize the foundation of management of the non-ferrous metal industry in Japan.To see the demand for nori-ferrous metals recover from the slump and be put on a path of solid development, we have to wait for the economies of the developing countries to ""take off"" and for its realization the economies of the developed countries must be reactivated with new growth industries playing a leading role, and the transfer of technology and money recycling must be carried out smoothly under an orderly international trade system."

Jan 1, 1983

By Robert B. Parsons

"The pendulum in Ottawa has swung dramatically from fiscal policy to monetary policy over the last several years. International trends indicate that the pendulum has to start its swing the other way, if Canada's mining industry is to maintain its preeminent position in the global mining arena. This article, which is based on a paper presented by the author at the 37th Annual Meeting of the Newfoundland Branch of CIM, identifies these trends and how they could interact with Canadian policy.IntroductionThe title of this paper is not a very imaginative or catchy one, but it states the topic quite succinctly, if not tersely. This paper looks into a crystal ball to see what might be in store for mine financing over the balance of the current decade.In the event that the reader feels some trepidation about the prospect that such a paper could seek to be the definitive work on the subject, it should be made clear at the outset that this is not the case. The author is, after all, not an economist, a scholar, a financial analyst, or a soothsayer, but is rather a simple accountant who has been closely involved with the mining industry, and the financing thereof, for some twenty years.The paper recognizes that, while a mine may be born when production begins, the mine is conceived when exploration starts. As this act of conception is obviously an essential part of mining, the financing of exploration is also covered in this paper. To attain a focus, this paper approaches the topic of mine financing in the nineties as follows: first, the major emerging forces in the industry are identified: and, second, the implications of each of these forces on financing are considered."

Jan 1, 1991

By Kosta Fytas, Nour-Eddine Chaouai

"Selection of the appropriate kriging plan during indicator kriging estimations is of a paramount importance to the precision of ore reserve estimation. However, very little is known on the sensitivy of indicator kriging results when changing the kriging plan parameters (mainly search distance and number of samples). This paper evaluates the effect of the search distance and number of samples on indicator kriging results using a gold deposit as a case study.IntroductionBlock estimation using kriging is based on the autocorrelation function (variogram) on one hand and on the kriging plan on the other. As far as the variogram is concerned it is more or less subjectively adjusted and this is reflected on its parameters (range, sill, nugget effect and anisotropy). The effect of a poor estimation of these parameters on the kriging variance of ordinary kriging has been proven very important (Brooker, 1986). Choosing a kriging plan is generally a difficult matter depending on the estimation type (global or local). Generally there is not a unique kriging plan be cause there is not a unique structural analysis (variogram). There are no rules or dogmas in choosing a kriging plan but it is rather a function of the sampling pattern (David, 1982).Structural analysis requires the hypothesis of quasistationarity but very often either the data available within the zone of quasi-stationarity are too many so that the search distance is reduced during kriging or the data are too few to satisfy a stationary kriging system (Journel and Huijbregts 1978). As a rule, the larger the neighbourhood, the more precise the estimates should be , but for large neighbourhoods the hypothesis of stationarity does not always hold (Rivoirard 1987; Armstrong and Champigny 1989)."

Jan 1, 1991

By R. Ghomashchi

Wear, fatigue and corrosion are the most widely encountered modes of failure in materials used in engineering applications, including aero-gas turbines. Although wear is distinctly classified as adhesive, abrasive, erosive, fretting and so on, there are usually more than one wear mechanism involved in the failure of components in service because there are many systems and materials variables active in materials wear that makes it more difficult to study. This is further complicated by the discrepancies between the results of laboratory tests and field data. The present investigation was set up to examine the wear characteristics of M50 and T1 high-speed steels at both room and elevated temperatures to draw a thorough understanding of the wear behavior of this class of high-speed steels. This article focuses on the mechanical and microstructural characterization of wear for T1 and M50 high-speed steels using a pin-on-disk wear machine.

Jan 1, 2005

By M. H. Moys, C. Bhondayi, Eric Tshibwabwa

"The relationship between froth bubble size as represented by intra-bubble impact distances (IID) and flotation performance is investigated. Experiments using an artificial ore comprising of limestone as the floatable component and silica as the gangue material were carried out in pseudo-steady-state circuit. A method to measure IIDs developed by Bhondayi and Moys (2014) was then used to measure froth bubble sizes as a function of froth height, superficial gas velocity and feed rate (pulp residence time). Samples for flotation performance evaluation were also taken. Results indicate that as froth height increases, the average IID values increase resulting in a decrease in limestone recovery while the grade increases. Increasing gas rate results in lower IID values that are accompanied by high recovery and low limestone grade. The effect of feed rate on both flotation performance and average IID values depended on froth depth and gas rate. Average IIDs largely remained the same at the two feed rates investigated.INTRODUCTIONIt is regarded as obvious that froth bubble size distribution (FBSD) will have an effect on plant grade and recovery. As the average FBSD decreases, the bubble surface area flux will increase making possible an increase in recovery and a decrease in grade. The opposite trend will be involved if average FBSD is increased. However: no method for measuring FBSD has been available, so these trends have not been studied in any detail. Bhondayi and Moys (2014) developed a novel technique to measure or estimate froth bubble sizes. Although they established a potential to use this method in understanding froth performance, no data have been presented to assess the correlation between the estimates of bubble sizes and actual flotation performance. In this work experiments are done to establish how the change in froth phase bubble sizes affect flotation performance. Flotation performance will be evaluated using recovery and grade. How water recovery to the concentrate changes with changes in bubble sizes will also be evaluated. It is known that water recovery is approximately inversely proportional to the square of the overflowing bubbles sizes. It will be interesting to establish how the rate of change of bubble sizes changes with water recovery."

Jan 1, 2016

By Andrew Cormier

"The Early YearsThe Grand Lake coal fields in New Brunswick undoubtedly can claim the distinction of being the first part of North America from which coal was mined and exported. The diaries of the Governor of Massachusetts during the first half of the 17th century clearly establish this fact. There is also a reference in the Massachusetts Colonial Records which indicate that coal exports to New England were carried on as early as 1639.It has generally been believed that Cape Breton mined and exported the first coal; but no account has yet been found to show that this took place earlier than 1676. Both at Grand Lake and Cape Breton the coal was near the surface and removed by hand.When the country passed entirely into British control, Joseph Garrison, a grantee of Maugerville in 1765 moved to Jemseg. While surveying the north side of Grand Lake he discovered outcroppings of coal on the shore of the lake and further inland along the banks of streams. It was he who named Newcastle Creek in reference to Newcastle in England, which was widely known for its coal mines. Joseph Garrison died in 1783, the same year that an influx of United Empire Loyalists increased settlement in Newcastle Creek in the area now known as Minto. Many Loyalists also settled on the shores on both sides of Grand Lake.At a number of points where streams cut channels through the overlying strata, the coal seams were exposed and it was at such outcroppings that the early operations were carried on. A tunnel was driven in the seam from the foot of the bank, affording both an outlet for the coal and natural drainage from the workings. The coal was loaded into boxes and wheeled over wooden tracks to a point on the surface where it could be dumped into wagons and hauled either direct to destination or to where it could be loaded into boats and conveyed via Grand Lake, Jemseg and Saint John river to points of distribution.In the latter part of the 18th century and first years of the 19th century, farmers were undisturbed by mining the coal found on their lands. This was soon to change and resulted in many years of contention between landowners and the Legislative Assembly.New Brunswick became a separate province from Nova Scotia in 1784 and the seat of government moved from Saint John to Fredericton in 1788. The new province had its first priorities; the establishment of counties, the building of roads, and the development of its natural resources. From 1805, records of coal and land development are fairly complete. These records show the increasing interest of the Province in developing the coal fields. This interest resulted in the granting of coal leases to many friends of the government, without any regard for the wishes of the farmers who owned and had occupied the land for many years. The farmers fought back with lawsuits and other forms of dissension but with little success. By the end of the 19th century there were very few farm operators left in the area."

Jan 1, 1992

By Gordon Sparks, Lyle Kajner

"An often over-looked component in the assessed value of a mining property is the value derived from the ability of the operator to limit financial losses during adverse economic times (i.e. low market price, high energy prices, etc.) by suspending operations. Overlooking the value of this type of operating flexibility when conducting mine investment analysis may negatively bias the risk profile for the investment by over estimating the investment's downside potential, thereby effectively undervaluing the investment. This paper illustrates the nature of the value of operating flexibility and discusses how it may be explicitly quantified within the context of conducting stochastic mine investment analysis. IntroductionMining properties are evaluated using an array of techniques ranging from simplistic non-discounted payback calculation s to sophisticated, discounted-stochastic simulation. Stochastic simulation analysis is perhaps the most robust mine investment analysis technique as it not only provides an estimate of the expected value of the property, but also quantifies the associated risks (for examples of stochastic mine investment analysis, see: Billingsley and Yaychuk, 1986; Gentry and O'Neil, 1984; Munro, 1977; or Harris, 1970).The quantification of risk is important as it provides the necessary yardstick required to allocate the corporation's resources efficiently. Resources are said to be allocated efficiently when the corporation's expected long-term financial reward is maximized while at the same time minimizing its risk (see Hertz, 1968; or Markowitz, 1952 for in depth discussions on efficiency as it relates to investment policy). The efficient allocation of resources should be the objective of any rational corporation. Therefore, rational corporations should employ stochastic evaluation techniques when screening their investments."

Jan 1, 1992

By J. Yue

The particle breakage kinetics, product size and size distribution, as well as grinding limit for quartz suspensions in a horizontal stirred mill are investigated. Results of grinding studies on quartz suspensions in a horizontal stirred mill confirm "first-order" particle breakage rates. A comparison of equation fits reveal that the product size distribution from stirred mill is best represented by the Rosin-Rammler equation when compared to the Gaudin-Shuhmann equation, but results fit poorly as particle size below five microns. A method of determining breakage rates versus particle size is demonstrated which shows that the 10% top size fraction is most appropriate for the determination of specific breakage rates. The method is used to demonstrate the relationship between particle breakage rate and particle size. As the feed particle size becomes smaller, the size reduction ratio decreases and approaches a grinding limit which depends on the effective stresses created in the mill.

May 1, 2004

By Friedrich Benthaus

"The natural and man-made realities on either side of the Atlantic are different. Therefore, a large part of the other side' s knowledge and experience cannot be transferred easily. In the following, the author will attempt to describe some of those developments in the German hard coal industry which may be of particular interest to readers on this side of the Atlantic.The area of the Federal Republic is quite small, especially if compared with a country as large as Canada. On a territory the size of the maritime provinces of New Brunswick and Nova Scotia, Germany holds coal reserves roughly corresponding to the total Canadian reserves. More than 20 billion tons of hard coal down to a depth of 1500 m, and more than 30 billion ton s of brown coal of lignite are technically and economically extractable acording to current technology.However, not only are Germany's coal resources more concentrated; the country is also densely populated, and there are dense networks of railroads and highways All components of the so-called infra-structure are available everywhere, be it electricity, any machinery or personnel. Public opinion is likely in favour of an increased utilization of coal.The coal industry is well developed through a long evolution covering centuries. As a consequence, there is an effective and intensive cooperation of numerous bodies and institutions concerned with coal mining, from government agencies including the inspectorate to suppliers, trade union s, producing companies, to jointly operated management and research organizations. In the Federal Republic, hard coal is mined in deep mines only, and lignite in general, only from open-cast pits. There is a complete organizational and geographic separation of hard and brown coal in Germany. Because the Federal Republic holds only insignificant mineral oil and very little natural gas deposits, coal is essentially the only and consequently the most valuable source of energy."

Jan 1, 1984

Thermal barrier coating (TBC) systems provide thermal insulation to high temperature for aero¬propulsion. A fracture mechanical model developed earlier for multilayer systems is applied on TBC to realize superior performance by enhancement of fracture resistance. Functionally gradient materials (FGM) solution concept is the basis of approach followed here. A few realistic FGM TBCs are considered in the analysis in addition to a conventional TBC as the base case and a hypothetical worst case with YSZ-YSZ interface. Parameters like number, composition and thickness of graded layers and elastic modulus are considered for the analysis and quantitative improvement of fracture resistance of TBCs. The analysis is confined to deep crack with crack size to width ratio as 0.5.

Jan 1, 2010

By Andrew Hickinbotham

"A water well represents not only a significant investment but also is a key to making a living or sustaining a reasonable lifestyle. This naturally makes the water well a precious possession that needsto be protected.This paper describes the challenges that TransAlta Utilities Corporation faced and how it responded to the concern of residents that open pit coal mining would affect their water well supplies.BackgroundWells have a certain mystique. Tum on the silver tap and water flows at your command without you knowing how it got there and whether it will continue to flow.Each well is different and has a story to tell. Some wells have a lot of history and are described fondly and with pride (""Grandad built this place 50 years ago and she hasn't failed us yet""). Some are passed on from father to son, some are part of the pride of good farming, some wells are famous for tapping that huge underground stream or have been mysteriously witched or have been part of a rip-off by an unscrupulous well driller. Some have to be babied so that the cows can be watered, the children can have showers and the dishes can be done. All wells represent a significant $5,000 to $10,000 investment and is a key to making a living or sustaining a reasonable lifestyle.Most wells continue to provide water faithfully - until there is a problem. For those people living next to a mine, there is the additional concern that mining has or will affect their water well supplies. Water well problems reported to the mining company have to be dealt with promptly and responsibly. The mining company's groundwater specialist must gain the trust and confidence of well owners living in the area ."

Jan 1, 1992

By J. G. Whellock, R. J. Phillips, J. W. Matousek, P. J. Marcantonio

"Stillwater Mining Company (SMC), a partnership of Chevron Resources and Manville Corporation, produces a copper-nickel, platinum-palladium flotation concentrate at its Nye, Montana mine. The concentrate is then toll processed in Europe. Recognizing the economic advantage of treating the concentrates at the mine site and of retaining this strategic resource in the United States, the Company commissioned Tolltreck International Limited and International Process Research Corporation to conduct pilot scale smelting tests with a flowsheet that would maximize metal recoveries while satisfying the environmental requirements of operations at Stillwater.Primary smelting was conducted in a single phase, 50 k W, submerged-arc, electric furnace. Refining the product mattes to copper-nickel ""white-metal""; containing approximately 2% iron, was accomplished in a Tolltreck, IV-litre, top blown rotary converter. Over-all platinum and palladium recoveries were approximately 99%; copper and nickel recoveries averaged 94%. INTRODUCTION(l-4)Stillwater Mining Company (SMC) a partnership of Chevron Resources and Manville, operates a copper-nickel, platinum palladium mine and concentrator at Nye, Montana, located in the valley of the Stillwater River, approximately, 100 km southwest of Billings. It is North America's only primary producer of these precious metals. The Stillwater area was mined for chrome ore during World War U and the Korean War, but it was not until 1961 that attention was drawn to the similarities between the Stillwater Complex and the Bushveld Complex of South Africa with its deposits of platinum group metals.A concentrated search for platinum was begun by Manville Corporation in 1967. Its presence, together with palladium, in mineable quantities was confirmed in the period 1976-1978, and the first partnership to develop the deposits was formed by Manville and Chevron in 1979. Anaconda joined the group in 1983, and in 1985 its share was purchased by Lac Minerals. In 1988 the interests of Lac Minerals were purchased by Chevron and Manville.The decision to develop the mine and build a concentrator was made in 1986. Construction began in the fall of that year, and the first concentrate was produced six months later, in March 1987. Underground mining is done in a two-shift, five day- week operation. Since startup, the concentrator has operated on a 24 hour/day, 7 day/week schedule, treating an average of 635 tonnes of ore per day and producing approximately 10 tonnes of concentrate."

Jan 1, 1989

By G Anders

The effectiveness of two types of powder used in long-wall slashing was compared. The evaluation of the results can serve as a good example of how the application of statistical methods to underground test data can help to minimize the number of tests to be carried out. The conclusions are stated concisely, including a definite assessment of the reliability of the tests. Introduction AN assignment at the Algom Nordic mine called for a performance comparison between 70 per cent Cilgel B and 75 per cent Dygel in longwall stope slashing, particularly taking into account, in both cases, the build-up of bootlegs as dependent on hole deviation. Stopes were usually 8 to 10 ft. high and inclined at about 17 degrees. Starting from a raise, they were widened by consecutive longwall slashes to 60 ft., and, al-lowing for drift pillars, were approximately 300 ft. in length along the incline.

Jan 1, 1964

By H. K. Taylor

"As a mining engineer with over 50 years' experience in underground operations and mine planning, I appreciate the enormous amount of work that went into the paper; and despite an imbalance between geology-geostatistics and the profit-earning actions of mining and treating (possibly because of sponsorship only by the Geological Society), I agree with probably 85% of the detail. But the paper fails to build on its own sound foundations and, like many predecessors, drifts instead into idealism. Even the starting quotation from the US SEC Form S-18 is little more than a platitude. An American consultant (l) has observed: ""an evaluation that accepts ore reserves as guaranteed because their definition meets SEC criteria is an invitation to disaster"".Idealism enshrines at least two myths that have bedevilled definition over the last several decades. The first is that the only purpose of 'ore reserves' is to promise successful new mines, and that 'ore reserves' must necessarily follow feasibility studies.In practice, the identification of what is likely to be mined if a mine is started must often be done on broad economics long before the feasibility study, and there may be only little later flexibility. The second myth is that there can be a perfect deposit with a simple exploration-appraisal-development sequence (the paper's Figure 2) against which all inferiors can be matched. If the field of definition be regarded as a pyramid, the quest for perfection and the imposition of rigid promises upon the terms 'ore' and 'reserves' drive definitions so near the apex (or the bottom right corner of Figure I, if preferred) that little is left to define. The process is reminiscent of the legendary super-medicine, the one so powerful that the patient had to be in perfect health to take it!"

Jan 1, 1992

By Donald C. Craighead

"Overland conveyor systems to transport bulk materials from mines to processing plants or load-out stations have to be seriously considered as the viable alternative to truck and train haulage systems. With the ever-increasing price of diesel fuel, conveyors with their electrical drives generally prove to be the least costly when operating and maintenance expenses are analyzed for the life of the installation.IntroductionOverland conveyor systems are now considered as one of the viable alternatives which should be closely investigated when a mining company and its engineers initiate studies on methods of transporting raw materials from a mine to a processing plant or rail load-out station.This paper will generalize the overland conveyor and compare it with alternative handling systems. Each installation must be carefully studied to determine the best route, type of foundations river crossings; amount of excavation work for cut and fill, maintenance roads, etc. No two locations are the same nor are the principles of operation of an overland conveyor the same as those of a normal plant or mine belt conveyor. The proper time and effort must be put into the study of the system to evaluate the costs for comparison with other systems.The length of the overland conveyor depends on the layout of the mine and plant and the topography of the terrain between the terminals. Individual lengths may be up to 20 km, and a series of conveyors may extend 100 km or more.Advantages of Overland ConveyorsThe main advantage of overland conveyors is the low operating and maintenance costs which will be realized over its years of operation. Although truck haulage probably will permit lower capital investment during the initial phases of the mine development when the annual capacities have not developed to the design level, their operating and maintenance costs will be considerably higher. When evaluating the total costs per ton of material to be handled during the expected life of the operation and the projected increases for diesel fuel versus electricity, overland conveyor systems will generally prove to be economically more viable."

Jan 1, 1982