Search Documents

By Gorrell. H. A.

Subsurface water data can be very valuable in .petroleum exploration and research. For the discussion of problems related to subsurface waters uniform nomenclature and classifications are required. The term 'connate water' has frequently been incorrectly used. It should .only be used in its original sense in which it is analagous to 'fossil water'. Classifications .based on origin and on sodium-chloride content are proposed. Present and possible uses of formation water analyses are briefly discussed. Since the potential uses of formation water data are not fully understood, complete analyses of selected samples should be made to insure against future requirements. The subsurface waters of Alberta show considerable regional variation in amount and proportion of dissolved salts.

Jan 1, 1958

By C. Gerow

THIS paper is entitled "Some" problems, rather than "The" problems, met in selling coal, since the problems to be met in selling any commodity have to deal with an infinite number of circumstances and conditions. These are believed to be more varied in the case of coal than probably any other commodity. This is due, perhaps, to the fact that coal has been one of the basic materials in the guiding of industrial and national achievement for the past two hundred years. During this time its use has developed from a most haphazard one to uses involving all modern scientific methods, which, rather than simplifying matters as regards the marketing of coal, have added many fresh problems, and these vary according to the particular market served. Since the concern of this paper is primarily the selling of Nova Scotia coal, it is proposed to deal chiefly with some of the specific conditions met in the markets presently served by this coal. For the purpose of discussion, these markets may be considered as divided into three main groups, namely, the Maritime market, the Quebec market, and the Ontario market. THE MARITIME MARKET First of all, let us consider the Maritime market. This is a market which has been regularly served by Nova Scotia coal since coal mining became the first industry in Cape Breton, slightly over one hundred years ago. Conditions as applying to the use of coal have naturally tended to adjust themselves to the characteristics of the coal most readily available, and, therefore, marketing problems are fewer in the Maritimes than in districts where many coals of varied characteristics are offered. Up to recent years, the problems involved were chiefly those of providing satisfactory service insofar as de-liveries were concerned. However, with the speeding-up of manufacturing processes and the necessity of reducing costs to a minimum, users of coal have become interested in obtaining coal that will give the most economical service. It is, therefore, now of importance that the salesman should have full knowledge of the particular conditions applicable to each customer's use in order to deal to the best advantage.

Jan 1, 1936

By John Canterford

Quay Magnesium Limited (QMG) listed on the Australian Stock Exchange in late September 2004 having raised approximately A$30 million with the object of designing, constructing, commissioning and operating a 15,000 t/a magnesium alloy production facility in Nanjing, China, Site construction commenced in February 2005 with installation of all major components completed by the end of October 2005, Hot commissioning was simultaneously commenced with the final stages of installation, leading to the first stage of continuous ingot casting by mid November 2005, Since that time ramp-up to the name plate capacity has been undertaken, This presentation highlights some of the more significant technical and logistical hurdles that have had to be overcome in order to meet the high quality product specifications required by a range of QMG customers.

Jan 1, 2006

By Donald P. MacKinnon

"This paper is a commentary on selected trends within the transportation industry.In general, innovations are taking place within all modes of transport (road, rail and water) serving the industrial minerals industry which will affect future distribution patterns, methods and costs. Significant technical innovations in the transportation of solids by• pipeline will also appear, perhaps in the near future, permitting the transport of specific commodities, including some industrial minerals. However, the timing and magnitude of the commercial exploitation of solids pipelines are heavily dictated by marketing factors and distribution system logistics, as well as by the innovations likely to take place within competitive modes of transport. Competitive technological developments will include increased ship capacities, improved bulk-handling facilities, larger and specialized bulk-handling rail equipment, unit trains, containerization, larger ""off-highway"" vehicles and greater inter-modal integration. Equally significant are some ""soft-ware"" techniques such as the growing interest in total distribution cost concepts. However, the impact of the developments will not be spread uniformly over all Canadian industrial minerals."

Jan 1, 1967

By W. G. Campbell

"The region discussed comprises approximately eight million acres spreading across the Arctic Circle in Yukon and North West Territories.Encouraged by four years of surface geological and geophysical work, which strongly suggested that suit-able conditions existed for the entrapment of oil and gas, a decision was reached to drill. In due course two holes were drilled; Eagle Plains No. 1 drilled to 9589 in 1957-8 and Western Minerals Chance No. 1 spudded in 1959 is being deepened this year.Thick sections of sedimentary rocks occur on both sides of the Richardson Mountains, however, most of our activities have been concentrated to date on the west side in the Eagle Plains basin. Here are found stratigraphic units ranging from Precambrian to Tertiary age. The drilling of the two exploratory wells proved the presence of these strata at depth and have confirmed the presence of promising structures. A geological cross-section across Eagle Plains presents an interpretation of these conditions.Physical and engineering aspects of exploration in the northern Yukon and North West Territories are de-pendent largely upon seasons and transportation. Reconnaissance gravity and surface geologic mapping by air presents no serious problems. However, seismic operations on the ground are greatly affected by the season, presence of permafrost and mobility of equipment.The actual drilling of the hole may well be the simple part of a wildcat undertaking once equipment and supplies are on location. Over-all planning, assembling supplies, transporting equipment and personnel seems to be the real job. Serious consideration must be given to per-ma-frost effect in the drilling pro-gram and on surface installations as well.Programming for -the various exploration activities should be under-taken well in advance of the actual doing. Considerable extra costs may be the results of crash programs. Costs are high, and the rewards uncertain. Economic evaluation is based •on the long term outlook."

Jan 1, 1960

By C. J. Sullivan

Many metalliferous ?provinces are co-extensive with particular groups of sedimentary, volcanic, or :basic plutonic rocks. Deposits may be truly syngenetic (Rand, Rhodesia-Katanga, Mans-field, Blind River, White Pine); re-. concentrated by circulating waters (Colorado Plateau, Red Bed Coppers) ; or re-concentrated thermally during metamorphism and granitization (most uranium and lead-zinc provinces ?and some copper and gold provinces). Basalts may yield important cop-per provinces when folded and re-heated. Granitization of basalts which have not reached the chlorite-carbon-ate phase of metamorphism may produce copper provinces. If they reach ?the chlorite-carbonate stage, granitization may result in a gold province. Copper and copper-nickel provinces may result if gabbros are granitized, and a ?similar alteration of per-idotite may result in asbestos or nickel ores. Many similar associations are known. Granite is not a source of ore, but a result of heat. A classification of ?ore with respect to source rocks is of greater prospecting value than are classifications based on magmatic differentiation and hydrother-mal solution theories. Volcanic centres are important ore foci because the thermally unstable metallic sulphides may be concentrated here by a distillation process. The ores found in the hot spring deposits, viz., mercury, mercury sulphide, sulphur, and the compounds of ?antimony and arsenic, are not those which are soluble in water at low temperature (epithermal sub-division of hydrothermal class), abrut those which are unstable thermally at comparatively low temperatures . Water is one of the most common thermally unstable minerals, and generally accompanies the thermally activated ore-forming sulphides.

Jan 1, 1957

By K. Negishi, H. Izui, Y. Komiya

"Aluminum has the disadvantage of low strength. In order to obtain the high strength composites, crystals were refined in the composites. Grain refinement was approached at two process points, generating new grains and grain growth. It is important for refinement how to control the grain growth. Spark plasma sintering (SPS) technique and TiB2powder addition prevent grain growth. To investigate effects of strain and additives to the alloy, aluminum powder was sintered at 70 MPa and 80 MPa, changing the content of TiB2additive powder by SPS method. As the results, the crystal grain size was finer in the composite sintered at higher sintering pressure and with larger amount of additive, though over 1.0mass% TiB2addition dissuades grain refining. These grain refinements improve hardness and tensile strength of sintered aluminum alloys.INTRODUCTIONAluminum matrix composites have low density, high specific strength, and low cost. Their applications are growing continuously in the field of automotive and aerospace industries. Recent studies to improve their good mechanical and tribological properties use different ceramic materials such as Al2O3(Das, Munroe, & Bandyopadhyay, 1996; Ashwatha & Anthony Xaviorb, 2014),SiC(Hassani, Bagherpour, & Qods, 2014), B4C(Ehsan, Masoud, Touradj, Amir Hossein, & Ali, 2015),TiC(Ehsan, Ali, Masoud, Kamyar, & Touradj, 2017), and TiB2(Fei & Zhong-Hua, 2013).On the other hand, grain refinement is also an important techniques for improving the properties of aluminum alloys. Finer grains improve the mechanical properties of the alloy. For cast and wrought alloys, addition of grain refiners in molten alloys accelerates generation of nucleus and suppresses grain growth. Al-Ti-B alloy is generally added as grain refiners in the molten aluminum alloys(Easton & Stjohn, 2001). Especially, TiB2has very high melting point, low density, and excellent hardness. Therefore, TiB2was selected as additions into aluminum alloys. Liquids reaction leads to high cost, oxidation, discoloration of molten alloy, and clustering of additive powder as compared with solid reaction such as sintering. However, sintering of aluminum alloy powder with ceramic powders is difficult for oxide layer surface. Recently, we take attention to spark plasma sintering (SPS) as advanced sintering process. SPS process can easily sinter a high quality specimen at a lower sintering temperature and in a shorter time than conventional sintering processes. By SPS process, we have sintered titanium powders that are as difficult to be sintered by any other processes as aluminum powders, and improved mechanical properties by adding hard ceramic powders TiC and TiB(Kamegawa, Izui, Komiya, Kobayashi, & Arimoto, 2015; Sampei, Izui, Komiya, Shigimura, & Suzuki, 2015). Furthermore, it is important to consider not only pure aluminum but alloys for solid-solution or precipitation strengthening. Actually, pure Al does not have enough strength compared with the alloys. Al-Cu alloy and Al-Mg alloy demonstrate adequate strength for industrial and commercial sectors. Al-Mg alloy retains good formability, and has high resistance to corrosion. It is therefore used for many applications. We must consider alloying processes. The most cost effective process is blended elemental technology where alloying elements are added to base powder as elemental or master alloy powder (Smugeresky & Dawson, 1981; Yasue, Radjai, Miwa, & Sakaguchi, 2003; Bolzoni, Esteban, Ruiz-Navas, & Gordo, 2012)."

Jan 1, 2018

By I. M. Marshall

A review of technical literature covering Canadian mining emphasizes the advancement and changes that have been made in mining practice. However, current technical publications rarely outline basic principles or state definite rules that govern profitable mine operation. it may be argued that the broad principles of mining have long a go been outlined in various handbooks, text-books, and periodicals, and that these principles never alter. This is in great part true, but modern machinery, improved meta1-lurgical practice, and other advances, have in part modified these principles or changed the manner of their application. Many engineers hesitate to state specific rules, because it is so easy to quote an exception to a rules that any such statement appears to lose weight upon its very utterance. The exception to rules, and the reluctance to formulate rules, has forced such maxims as "the only rule in mining is the point of a pick," and "gold is where you find it". As an illustration of rules and their exceptions, one might quote the time-honoured maxim that a mill should not be built before a shaft has been sunk on a property in point of fact, Canadian mining history is replete with examples of wasted capital where a mill was built before a shaft had been bottomed. Y et this past year has seen a property enter profitable production whereon the building of the mill was started before the shaft was sunk. Instances such as this should not be accepted as evidence that a rule has been overthrown, but rather as an exception to the rule. The case cited pays tribute to the application of the diamond-drill combined with the correlation of sound geology. Incidentally, both these features emphasize a modern trend in the development of Canadian mining properties-a trend that is perhaps worthy of further comment. It is such trends that affect the principles of mining or modify their application. It is with such that this paper deals, at ]east in part. It is hoped that the statement of principles and the opinions herein outlined will be of sufficient interest to arouse discussion.

Jan 1, 1939

By S. Rash Ahmadi

One of the most important elements in power plants is rotors and repairing the damaged rotors is very important in view point of economics. One of the most complicated problems in power plants is increasing of stiffness of the turbine rotors. This problem which occurs mainly due to thermal shock or rubbing makes to exit damaged rotor from service. These elements can be repaired effectively by heat treatment methods. Tempering heat treatment is the most common solution for straightening of damaged rotors but it requires having good knowledge about heat treatment parameters (temperature and time) and their affects on fundamental properties of rotors. In this article, a suitable method is introduced in order to modify the increased stiffness in journal part of rotors due to martensite transformation, using heat treatment tempering process.

Oct 1, 2011

By Sadough vanini Ali

Charpy impact energy of functionally graded steels produced by electroslag remelting in crack divider configuration has been modeled in various strain rates. It has been well known that majority of materials indicate different behaviors under different strain rates and temperatures. Therefore, modifying the elastic-plastic model considering the effects of strain rates and temperature gives us an acceptable prediction of these composites behaviors in impact test. In this investigation, graded steel was divided in to several layers in which the layers have the same strains under the impact. Constitutive equation describing the flow stress variations as a function of strain rates and temperatures, have been used to express the stressstrain behavior of layers. The parameter values of constitutive equation determined for all the layers via using the boundary conditions based on composite graded behaviors which were the characterized ferrite, austenite, bainite and martensitte phases. Consequently by applying the rule of phase mixtures and ascribing the impact energy of each layer to the area of stress-strain curve of the same layer, the whole impact energy of composite is the sum of layers impact energy with considering the layers volume fraction.

Oct 1, 2011

By V. Songmene, R. Khettabi, J. Masounave, R. D. Njoya

L'augmentation régulière des règlements environnementaux et de la sécurité au travail deviennent de plus en plus strictes. L'usinage fait partie des opérations industrielles qui peuvent causer des problèmes de santé au travail et sur l'environnement. La plupart des particules de poussières produites pendant toutes les opérations d'usinage à sec ou lubrifie causent des nuisances environnementales graves. Le travail propose étudie l’influence des paramètres de coupe, des alliages et des états des matériaux sur la formation des copeaux et sur la génération de poussière lors de l'usinage à sec. Deux modes d'usinage (le fraisage et le perçage) sont abordés. Une loi reliant la ténacité des matériaux aux émissions de poussières est proposée. Les effets des matériaux et de leurs conditions, ainsi que des procédés d'usinage sur la génération des poussières ont été mis en évidence. Des mécanismes de formation de poussières sont identifiés et reliés à la formation des copeaux.

Jan 1, 2006

By P. H. Shipway, D. G. McCartney, H. Saghafifar

The microstructural changes during thermal ageing at 650ºC in the interfacial region of Alloy 625 weld overlay on a 2.25Cr-1Mo steel was evaluated. Optical microscopy, scanning electron microscopy in SE and BSE modes, electron probe microanalysis and hardness mapping were used to characterize as-welded microstructure and its changes during thermal ageing and precipitates of interfacial region. Carbon migration across the interface was recognised as a major issue. A region of 300 µm wide adjacent to the fusion line, which was found harder in the as-welded condition decarburized during thermal exposure. Studies revealed that this region transformed to a soft region containing large ferrite grains and micron-sized carbides. In the weld overlay, a 50 µm wide hard band (over 650 Kgf mm-2) adjacent to the fusion line formed and carbide precipitates were observed along grain boundaries. Carbide precipitation mostly occured in the 150 µm wide region close to fusion line.

Jan 1, 2017

By S. Rash Ahmadi

Welding is highly reliable and efficient metal joining process. In welding the metal adjacent to the weld joint is subjected to severe thermal conditions. As a result, complex changes in metallurgical structure occur in this region. These changes in structure depend on the material and the temperature history experienced. Friction stir welding (FSW) is relatively a new welding process in which, heat is generated by friction between the tool and the workpiece. The amount of heat conducted into the workpiece determines the quality of weld, residual stress and distortion of the workpiece. The objective of the current work is to study the transient temperature in a friction stir welding. So, a three dimensional transient analytical model is used to study the thermal distribution during the welding. Heat input from the tool shoulder alone is considered in the model. The process parameters like axial load, welding speed and tool rotational speed, used in actual FSW process are taken to build the model. This analytical model is very useful for select the optimized affected parameters in friction stir welding. The model illustrates the comprehensive equation including actual affected parameters in FSW and it can be used for different materials. In addition to the above the thermal history finds application in design of welding tools.

Oct 1, 2011

By S. A. Sadough vanini

In this paper, Stress-Strain-Temperature relations for Shape Memory Alloys are studied. Temperature effects on Shape Memory Alloys are different from those related to ordinary materials. In ordinary materials, elastic characteristics can be assumed to be constant in low temperature ranges, and only the deflection arising from temperature changes could be added to the elastic defection. As long as two phases of austenite and martensite could be present in Shape Memory Alloys simultaneously, elastic modulus follows temperature and temperature gradient. In continue a smart actuator is investigated considering a homogeneous cantilever beam. Beam bending is established by using shape memory wires. An initial strain is imposed to shape memory wires in a low temperature, and then, they are installed in the outer surface of the beam. Therefore, since the temperature is imposed in these wires and they cannot have free recovery strain, the compressive recovery stress will be produced in the outer surface. This will result in a deflection in axial direction of the beam. At first, beam deflection is calculated on the basis of theoretical relations and solving the relevant differential equations. Afterwards, experimental tests are performed on an elastomeric beam equipped with shape memory wires. When a voltage is applied, a temperature rise will occur in the wires; then, this temperature rise causes a deflection in the beam. Finally, the theoretical and experimental results? comparison indicates a good conformity. One capability of this actuator is its high flexibility, and by controlling the inlet current, the end-beam deflection can be controlled.

Oct 1, 2011

By H. B. Gillis

THE following pages c9ntain a brief description of the processes involved in the manufacture of silica brick at the Sydney plant of the Dominion Steel & Coal Corporation. Silica brick manufacture was commenced at Sydney in 1918, for the purpose of supplying the requirements of the steel plant, where about three million silica bricks were used annually. Previous to that date, all silica refractories were brought to Sydney from American sources and were subject to a freight cost of nine dollars per ton, or about twenty-seven dollars per thousand. As a preliminary step to manufacture, a thorough investigation of all possible sources of silica in the vicinity of Sydney was carried on during 1916 and 1917. ?Eighteen separate deposits were examined. Of this number, only four were found suitable for brick making, and the Leitches Creek silica, being the nearest of these four deposits to Sydney, was selected as the raw material for the proposed plant. CRYSTAL MODIFICATIONS OF SILICA A brief review of the silica minerals may serve to indicate why careful investigation of sources of supply is necessary before actual brick-making is attempted. The crystal modifications of silica, i.e., quartz, tridymite, and cristobalite, all possessing alpha and beta phases, play a most important part in determining the suitability or otherwise of the resulting brick. By heat treatment, any one of these forms of silica may be converted to either of the others. The inversion temperatures (after Fenner) in degrees Centigrade are shown on rage 160.

Jan 1, 1938

By Allan R. Punkkinen

Safe extraction of the valued ore resource in the deep levels of VALE Creighton Mine has progressed in a pillar-less fashion using vertical retreat, slot-slash and uppers retreat methods since the cessation of ?cut and fill? mining in the late 1980?s. Sequencing of the panel extraction and filling has been the key to successful exploitation of high stress orebodies at depth. In late 2010, discussions between the Operating Department and Creighton Ground Control revealed an opportunity to evaluate a trial primarysecondary sequence in the west end of the 400 Orebody at the 2340m horizon. To manage the trial primarysecondary project, a high level risk analysis and management of change was carried out to mitigate potential danger. As part of the requirements, an instrumentation project was conducted in the hanging wall and footwall bottomsills of the secondary panel and within the secondary panel itself. The extraction sequence was modeled with Map3D® software, confirming high stress levels with the advance of the primary panel. Enhanced ground support was installed based on modelling results. A key objective of the instrumentation project was to verify support system response to mining and to obtain knowledge in regards to the behavior of the stope. This paper describes the first time that this type of new innovative instrumented rockbolt technology had been used in a hard rock mining environment. Understanding of the physical deformation mechanisms of ground support in response to high stress conditions is the basis for an effective ground control strategy. The data played an important role in subsequent enhanced ground support system design at the mine and importantly, established the fact that the secondary pillar had not totally failed. Subsequent cavity monitor results helped establish that fact.

Jun 1, 2012

By R. A. Gannicott

Trend surface analysis was used to investigate the geochemical dispersion patterns of Si, Ai, Fe, Mg, Ca, Na, K, Ti and Rb in the footwall of the Seneca massive sulphide prospect in southwestern British Columbia. Surfaces for various element ratios were also produced to see if the distributions of the elements are related to each other. Trends developed by the elements redistributed during hydrothermal alteration may be difficult to detect for various reasons, such as too few and widely separated sample points, random analytical errors or local variations in rock chemical composition that are not related to regional trends. Trend surface analysis is useful to distinguish regional trends from local fluctuations. The computer program used in this study is capable of calculating surfaces up to the 6th degree polynomial, but provides for automatic termination when the variables in the equation for successive surfaces become effectively collinear. With the relatively small number of data points used (21 samples) in this study, such termination occurred after the quadratic surface. Results show that, at the Seneca prospect, Mg and K increase, and Na and Ca decrease, toward a common centre which corresponds closely with the best drill-core intersections of ore. The centre is interpreted as a volcanic vent and as the source of mineralization . Quadratic surfaces for element ratios show that K/Ca decreases and Fe/Mg increases away from this vent. Thin-section and X-ray diffraction analyses indicate that these variations reflect sericitization of plagioclase and an increase in the Mg content of chlorite near the vent. The mineralization , rock types and element dispersion patterns at the Seneca prospect are similar to those reported for volcanogenic massive sulphide deposits at Bathurst, New Brunswick, and in the Hokuroko district of Japan.

Jan 1, 1979

By Chris M. Healey

"The Jasper Gold mine in northern Saskatchewan produced a total mill feed of 140 127 tonnes at an average grade of 19.0 g/t Au. Both diamond drilling and chip samples from underground workings returned extremely high values, up to 12851 g/t (375 oz/T) Au over 0.10 meter from a chip sample. In the presence of such extremely high grades, the accurate estimation of reserves is a major problem.In the first part of this study, production data from the mine were used to evaluate the results of a variety of reserve estimation techniques in this environment. In two out of three cases studied, indicator kriging with assays cut to 342.9 g/t (10 oz/T) gave extremely good results. In the third case, however, indicator kriging gave unacceptable results. Instead, lognormal kriging of uncut data gave the best results.Secondly, from the same database, a number of drill-hole spacings were simulated, and reserves estimated from the simulations. As may be expected, the results of this analysis show increasingly better results with tighter drill-hole spacing. However, even with a 5 m by 5 m spacing the variation from actual grade was quite large. This is not a systematic under- or over-estimation of grade, rather a random scatter of results.The results of this study show very clearly the problems of deriving good estimates of reserves when extremely high-grade samples are encountered. There is a high degree of randomness to this data base, so reserve estimation in this situation will remain a high-risk operation."

Jan 1, 1993

By J. Bigu, M. G. Grenier

"Dust size distribution and aerosol size distribution measurements have been carried out in several Canadian underground uranium mines. In addition, dust samples have been analyzed for long-lived radioactive products of the U-238 and Th-232 natural decay chains using ex-spectroscopy and -y-spectroscopy techniques.From the data collected one may summarize: (a) most airborne particulates are of size below I u-m and 50% by mass are found above 1 u-m; (b) dust clouds are bimodal; (c) preferential deposition of radon (thoron) daughters takes place on airborne particulates in the sub -micron range at about 0.1 u-m; (d) deposition of radon (thoron) daughters is proportional to particle surface area; and (e) ex-spectroscopy and -y-spectroscopy of dust samples reveals the presence of U-238, Ra-226 and some of their short-lived and long-lived decay products.IntroductionExtended inhalation of airborne radioisotopes poses a potential health problem to occupational workers. Because of this, monitoring of radiation and dust levels for dose exposure calculation purposes is not only recommended but in most cases mandatory.CANMET (Energy, Mines a nd Resources Canada) has long since been engaged in a comprehensive monitoring program aimed at determining dust concentrations in the respirable size range, aerosol concentration in the sub-micron range, and in the radioactivity associated with these particulates in underground uranium mines. Measurements have been carried-out with gravimetric dust samplers, dust size selectors (including a horizontal elutriator , a fineparticle spectrometer and Nuclepore* filters of different pore sizes) and a condensation nucleus counter(1 – 6). Inactive and active working sites have been monitored according to some typical mining operations. A summary of these data has been given elsewhere(3- 5)."

Jan 1, 1984

By L. A. Homeniuk, R. Bonnar

"The Fond-du-Lac uranium deposit is located on the northern rim of the Athabasca Basin. The uranium mineralization is, for the most part, confined to the Athabasca Group, which is underlain by pre-Helikian metamorphic rocks of the Western Craton.The deposit is characterized by a remarkable train of mineralized glacial erratics which led to the original discovery. The mineralization is present as a ""high-grade"" core and a diffuse ""low-grade"" aureole. The ""high-grade"" core occurs as a stockwork of steeply dipping pitchblende veins which strike N 50°E. Hematite, siderite and secondary silicate are also abundant. The ""low-grade"" aureole contains uraniferous goethite, argillaceous material and rare carbon buttons. Recent alteration to coffinite has taken place along the margins of pre-existing ore minerals.The ""high-grade"" core is 390 m long and 10 to 40 m wide, and is surrounded by an irregularly shaped zone of ""low-grade"" mineralization with a similar length and a width of up to 350 m.Comparing the Fond-du-Lac deposit to other unconformity-type deposits, several important differences can be noted:1. Ninety per cent of the ore is above the unconformity, in the Athabasca sandstone.2. The deposit is not associated with underlying graphitic rocks or a major structure.3. The clay-rich alteration zone is not extensive around the Fond-du-Lac deposit.Although there are differences with other Athabasca unconformity-type deposits, the high-grade portion below the unconformity suggests a common origin.The ore deposit is postulated to have been formed from uranium-bearing solutions which entered the stockwork of fractures. Following the reduction in part of these solutions by pre-existing carbonaceous matter and pyrite and/or chemical reaction with pre-existing hematite, deposition continued as a result of decreasing temperature and pressure. Subsequently, minor supergene redistribution of the uranium has taken place."

Jan 1, 1982