Search Documents

By J. A. Ressinger

"The purpose of this paper is to discuss some of the differences between various methods of excavating and loading as they relate to mining operations. The intent is not to provide ""pat"" answers, but instead to raise some questions and set forth some reasonable guidelines.Specifically, the paper deals with the differences and relative merits of power shovels versus rubber-tired front-end loaders - or, carrying this further, comparing what could be called ""stationary"" loading or excavating devices to ""mobile"" types."

Jan 1, 1972

By H. J. Ni, M. Y. Huang, S. W. Chen

The effects of several fluxes on purification, microstructures and properties of A00 aluminium have been studied. The experimental results and analyses indicate that many cracks and large porosities exist in the surface film above the melt purified by C2Cl6 and that the film is floe and mostly composed of AhO3 and pure aluminum, which carries many carbon particles and AlCh not fully volatilized. And then over 50% of the all-melting residue is pure aluminum, which is one of the major reasons for high melting loss. Moreover, because of a mass of gas bubbles and a state of seethe, there exist many inclusions which size is under l0µm in the microstructure of A00 aluminum purified with C2Cl6 or fluxes containing C2Cl6- With this purifying method, the aluminum crystal grains are extended along the radius that was observed firstly and the average crystal size of A00 aluminum are about 100µm~150µm. In addition, small size inclusions have little affected on tensile strength and micro inclusions under l0µm have little affected on elongation.

Jan 1, 2006

By M. K. Gangal, A. E. Hall, S. B. V. Stewart

"An investigation into the problem of atmospheric fog in Canadian mines is described. Fog occurs in several mines and the reduced visibility can result in the closure of workings for safety reasons. Information on the mechanisms of fog formation are discussed and the methods for improving conditions are reviewed with their relative costs.INTRODUCTIONAtmospheric fog occurs in several Canadian mines during spring and summer. The fog which reduces visibility, contributes to loss of production and increased accident risk . Closure of ramps in mechanized mines causes mining to be stopped or rescheduled, and stoping and grade control may be affected . Increased corrosion of equipment may result from acidic fog .Fog is commonly caused by saturated air being compressed and heated by an inlet fan and then being circulated in an ascensional system with heat transfer to the walls of wet airways. This causes supersaturation and water droplets condense to create fog, with liquid water contents of 0.5 g/kg to 3 g/kg of air. These concentrations reduce visibility to less than 10m and prevent mining. Less severe fog is usually tolerated as a nuisance, about which little can be done."

Jan 1, 1989

By J. Ander

About fifteen years age some mines in western Canada commenced using Diesel engines, partly for development work but also for operations on quite a large scale. In the Eastern mining field, the Diesel engine made its appearance some eight years ago and has since, at quite a number of mining plants, proved to be a reliable and economical prime mover. As a result, it is today used more extensively than could have been foreseen only a few years ago, and it is reasonably safe to predict that the next few years will see the Diesel engine utilized to a still greater extent in the Canadian mining industry. It is not much more than thirty years since the first Diesel engine was put in operation. During the early years of this century, the Diesel engine took, so to say, its first faltering steps in public service. Since then it has reached a high state of perfection, and its importance has grown in a most remarkable way, until today it is used in practically every field where power is required. It is slowly but surely superceding steam for a great many purposes, as, for instance, for ship propulsion. While in 1921 only about 8 per cent of all tonnage launched was motor-driven, the proportion had grown to 38 per cent in 1927, and for 1929 it was slightly over 45 per cent. Some of the finest passenger liners afloat are Diesel-driven. In the early days, Diesel engines were built only in comparatively small units. Today engines with a capacity per unit of up to 10,000 horsepower, or even more, are being built for marine and stationary purposes.

Jan 1, 1930

By Cummings. J. B., R. Haworth

"THE OPERATION of the Potash Company of America, Ltd., at its plant near Saskatoon, Saskatchewan, is the result of many years of exploratory and development work, culminating in the construction of a shaft, milling, concentrating and other facilities necessary to the production of potash in a marketable form.The possibility that potash existed in •commercial quantities in Saskatchewan was first indicated in 1943, although it was not until mid-1946, when Bata Petroleums penetrated a potash bed at its Verbata No. 2 well near Unity that substantial in-ter.est was developed in the possible exploitation of this important mineral product.The Potash Company of America, which is the largest producer of pot-ash in the Carlsbad, New Mexico area, a district that has been sup-plying about 90 per cent of the North American potash demand, be-came interested in the Saskatchewan deposits •at an early stage. Its engineers made an intensive study of the western Saskatchewan area in 1947 and continued their review of operating problems throughout the next three years.""Potash"" is the commonly used general term applied to the minerals of potassium, of which there are several. The most common mineral forms in which it is produced are potassium chloride and potassium sulphate. The potash content of potassium compounds is ordinarily ex-pressed in terms of potassium oxide (K20) equivalent."

Jan 1, 1960

"INTRODUCTION Secondary mine ventilation has been hamstrung by the availability of fans that satisfy many competing operational factors. The sometimes legislated requirement of adequate volume to the working face, the minimisation of excavation required to fit the selected secondary fan and the power requirements of various operational phases has, in the past, not been satisfied with just one system. The new system being introduced overcomes all these competing requirements in one simple unit with an added bonus of being very durable without loss of performance when wear occurs on the impeller. Existing Operational Situation Several studies (e.g., CIPEC, 2005; LCG Energy Management Group, 2009) have found that between 42% and 49% of mining energy costs are associated with mine ventilation, depending on the type of mine and the equipment used. If we then look at the general breakdown of installed power of the secondary fan to primary vent fans, the ratio is around 2:1. Thus the total energy costs of the secondary ventilation represents about 25% of the overall mining energy costs. It is of interest to note that the cost of running a typical two stage axial vs the cost of purchasing and general maintenance cost of the same fan over a 10 year period, the breakdown will be conservatively in the order of 40:1.The currently available secondary ventilation axial fan have one duty curve at any given time. Generally this can be changed manually within the motor power parameters but requires a minor outage and removal of the fan to do the pitch adjustments. As the bag vent ducts grow longer, the supplied air reduces to a point where inadequate air is supplied to the working face. This is exacerbated by underground equipment putting additional resistance in the heading and further reducing the supplied air at the working face. This shortfall is normally corrected by the installation of an additional fan in the system to overcome losses in the bag system but comes at a cost of production as the heading needs to be shutdown to install the second fan. This also means that the heading is supplied with excessive air on the shorter runs with a wastage of fan power."

Jan 1, 2019

By T. Richard Davies

This paper primarily deals with the application of wearfacing materials and their role within a well-established preventive maintenance welding program. Some examples are shown, as well as a synopsis of possible benefits and a compendium of methods and materials.

Jan 1, 1979

By R. E. Ray

"As real estate for new development in urban settings becomes scarce, commercial high rises are being constructed above open passenger rail tracks and vehicular roadways. Rail and roadway overbuilds are treated as tunnels requiring emergency ventilation systems for train or automobile and truck fires. The value of floor space in residential and office towers poses challenges to engineers responsible for designing fan rooms and shafts for tunnel ventilation systems within the towers. This paper describes a case study of the unique incorporation of tunnel ventilation fan plants in the overbuild structure of a passenger railyard and an adjacent roadway.INTRODUCTIONTunnel ventilation systems are required for passenger rail and transit (subway) tunnels by the NFPA 130 Standard for Fixed Guideway Transit and Passenger Rail Systems, and the NFPA 502 Standard for Road Tunnels, Bridges, and Other Limited Access Highways requires tunnel ventilation systems for vehicular (road) tunnels. Passenger rail and transit (subway) tunnels are typically ventilated with a series of shafts placed longitudinally along the tunnels to provide piston relief for normal train operations and emergency ventilation of train fires utilizing reversible axial flow fans. The shafts are incorporated in dedicated ventilation buildings that house the tunnel ventilation fans and starters, switchgear to power the fans and other equipment and systems in the building, Programmable Logic Controllers (PLCs) to control fan operation with Supervisory Control and Data Acquisition (SCADA) software, and HVAC fans and ductwork to ventilate the spaces in the building. These ventilation buildings may also provide access to the tunnels below with ingress/egress stairs for use by first responders and firefighters entering the tunnels and train or transit system passengers exiting the tunnels in an emergency. A photograph of a passenger rail ventilation building that encompasses four tunnels is shown in Figure 1."

Jan 1, 2019

By DON E. MacDONALD

Marl in Alberta is confined to highly specific geological, hydrogeologica/ and climatic settings. Tufa is fa irly abundant in those areas of western Alberta where bedrock is of the Paskapoo Formation. Marl and tufa originate when the following conditions are met: presence of a carbonate source in drift or nearsurface bedrock; leaching of the carbonate by percolating groundwater; transportation of calcium and bicarbonate ions in a permeable aquifer; discharge at the surface as springs, seeps or lakes; re-precipitation of calcium carbonate. Alberta has seven categories of marl and tufa deposits, based upon over-all depositional environment and calcium carbonate

Jan 1, 1984

By L. W. Krahenbil

The programmable Logic Controller (PLC), at its present stage of evolution, is now considered as a mature control system. The PLC combines the solid-state reliability of hardwired logic and computer control systems with the simplicity of a relay ladder logic. Relay symbolic programming through a function-oriented keyboard provides a means which plant personnel can easily become accustomed to work with. In a large coal facility, it is shown that the control engineer can provide improved control flexibility with the advanced capabilities of the PLC.

Jan 1, 1979

By P. Personnet, D. Wheaton, E. Couzinie, V. Demetriou, Brooks. W., G. Girault, M. Meyer, L. Charbonnel

A common problem in Gas Treatment Centers (GTC) from primary aluminium smelters is the temperature of the gas to be treated : above a threshold, filtering media are irreversibly damaged. The traditional way of dealing with high gas temperature is to dilute with fresh air, which implies over sizing - and therefore higher cost for - the GTC in order to have the capacity to treat this dilution air without compromising on pot suction. A system was developed which decreases gas temperature without having to use dilution air. This system is based on water pulverization in gas collectors. The water vaporization leads to a temperature decrease of the gas. A pilot system was trialed in our R&D unit. Satisfactory results led to the development of an industrial system based on Envirocare equipment (partnership), which was trialed in our production plant in Tomago (NSW, Australia). This patented system was then generalized in this plant, which is now using it with success during austral summer.

Jan 1, 2006

By Victor F. Hollister

Elemental sulphur occurs as aformational sedimentary deposit in Upper Devonian Wabamun evaporites near Coronation, Alberta. The deposit developed in a stratigraphic jacies-change lrap; it is assumed that petroleum reacted with anhydrite to form sulphur, calcite, hydrogen sulphide and other reaction products. The deposit contains about 362,800 tonnes of sulphur and lies at a depth of 1200 m. The Coronation deposit is expected to be geologically typical of such other native sulphur deposits as may be found in Wabamun Group sediments. Widespread sour gas sulphur production f rom the Wabamun suggests the possibility that additional native sulphur deposits will ·be found.

Jan 1, 1984

By Tyler Roberts

New Afton mine is an 11,000 tonne per day block caving operation, located 8 km west of the city of Kamloops, British Columbia. Due to the nature of block caving and the weak rock mass at New Afton, the mine has faced and overcome many blasting challenges during its ramp-up to commercial production. As New Afton Mine continues to grow the demand for drill and blast precision has continued to grow as well; any misstep incurs delays in achieving full production capacity. The block cave mining method used at New Afton employs single-shot draw-bells, fired with very little void and blind undercutting, allowing little margin for error. New Afton has made continuous improvements to its blasting strategy by reacting quickly to real-time problems and employing sustainable, repeatable solutions to overcome its unique blasting requirements. Examples of these solutions include: increasing blast hole diameter, casing production drill holes, developing pre-loading procedures and developing strategies for remotely blasting under-broken remnants in both draw-bells and undercutting. Increasing the blast hole diameter has alleviated initial problems with hole plugging in the highly jointed rock mass at New Afton. This has reduced drill-cleaning time significantly and enabled New Afton to meet blasting targets. PVC hole casing was trialed when blasting in extremely fractured ground, where drill holes continually plugged. The casing allowed the drill holes to remain open long enough to load and blast. Calculations were carried out in order to achieve the same explosive energy in the cased holes as a typical blast. Results were generally positive, but more testing is required. Production flexibility and scheduling reliability have been maintained at New Afton by developing a pre-loading procedure for the production undercutting. In doing so, New Afton has been able to keep productivity high by having a flexible production schedule that is not reliant on a specific piece of equipment or production drive to remain productive; this flexibility is because the mucking of undercut material can occur at any stage of the drill/blast/muck cycle. New Afton has developed a strategy for blasting remnant under-break in its draw-bells and undercutting by remotely drilling holes near to the under-broken section and then loading the toes of these holes with emulsion, the remainder of the hole is then filled with grout. The holes are grouted in order to prevent damage to permanent pillars between draw-bells (where the majority of the recovery holes need to be located). Several critical areas were recovered using this technique with little to no damage to the remaining permanent pillars. Innovative blasting solutions have allowed New Afton to overcome obstacles in order to become a producing operation. Moving forward, New Afton looks to continue its trend of innovative drilling and blasting techniques when faced with out of the ordinary situations.

Aug 1, 2013

By Jun Dai

Based upon research findings from several countries, the combination of microwave and mechanical means to break hard rock holds promise for the future. To achieve this goal, it is essential to understand the laws governing strength reduction of hard rock, such as granite, induced by microwave irradiation. Two aspects to consider are: 1) laws associated with the tensile strength of hard rock after microwave irradiation and 2) the sensitivity of different types of rock strengths to microwave energy. In this study, granite with a range of tensile strengths was exposed to microwaves for various time periods to compare the response of rocks with different strength values exposed to the same microwave irradiation. In addition, a method based on hotspots is presented to explain the mechanism by which granite strength is reduced by microwave irradiation. Granite extracted from Qinling Mountain in Shaanxi Province, China is used in the research. ?50 × 50 mm cylindrical granite specimens were exposed to microwaves at a specific power level. The strength values of the heated granite specimens were compared with those of unheated specimens. Through the comparison and analyses, relationships were determined between 1) reduction in granite strength and microwave irradiation time period, and 2) granite strength and sensitivity to a given energy of microwave irradiation. Finally, a mechanism to explain the experimental results is proposed. Research findings will aid in the design of a microwave + machine rock-breaking system for use in rock breakage in underground mines at depth and for future mine applications on earth and other planets. In addition, the experimental approach could be used to test other rock types to further our understanding of rock damage induced by microwave irradiation.

Aug 1, 2013

By M. J. Marinigh

Increased safety requirements, higher operational costs, greater environmental restrictions, and new competitive processing techniques are the challenges smelter operators must confront in order to remain economically viable. In converting furnaces which have tuyeres such as the Noranda Reactor and the Teniente, Peirce Smith and Hoboken converters, efficient tuyere line management is critical to optimizing blowing rates, increasing refractory life, and improving safety. This paper will describe recent improvements made to equipment used for tuyere punching, tuyere silencing, tuyere pyrometry and refractory drilling of tuyeres and how the proper application of the equipment can lead to operational and safety improvements.

Jan 1, 2007

By P. Farsangi, A. Hara

"Kidd Creek Mines places approximately 10 000 tonnes of consolidated rockfill on a daily basis. Consolidated rockfill is comprised of sized aggregate mixed with different ratio and amounts of binders. Consolidated rockfill, with closely controlled specification, is employed for subsequent pillar recovery and improved passive active/ ground support. With the same amount of cementing agents consolidated rockfill mass yields a higher, compressive strength, modulus of elasticity, cohesion, and angle of friction compared to a typical cemented hydraulic fill mass.The consolidated rockfill at Kidd Creek Mines is designed to sustain not only the gravitational loading of the overlaying fill material, but also to some extent the dynamic loading applied during blasting of the adjacent stopes and/or pillars.The quality control of materials used in Kidd Creek's rockfill system could be effected in three stages of handling: (1) at the surface backfill plant; (2) during transportation; and (3) placement of the fill.The emphasis in this paper is placed on individual stope backfill design and quality control measures at Kidd Creek Mines to place fill in large-scale open stopes which eventually could be exposed on all four walls during pillar recoveries."

Jan 1, 1993

By Eric Johnson

"IntroductionHistoricalCyanidation is a leaching process, in world-wide use, to extract gold (and silver) from ores and concentrates. The process has many inherent advantages on account of its adaptability:a. to any scale of operation;b. to a wide range of ore types and mineral associations;c. to a wide range of physical characteristics of the gold particle size, alloy (electrum) or mineral (telluride);d. to relatively simple plant controls and operating procedures;e. to simple marketing procedures and quick cash return.The basic idea for cyanidation was first described and patented by a German chemist, L. Elsner, in 1846. Some forty years later, J.S. McArthur, a metallurgical chemist and R.W. and W. Forrest, medical doctors, all of Glasgow, Scotland, came to realize the import of the discovery and accordingly, registered patents in Great Britain in 1887 and in the United States in 1889. The keystone of the McArthur-Forrest patent registration was the use of weak (0.05o/o) instead of strong (1.0%) solution.The years 1890-1910 saw much progress in equipment design and the advance from batch to continuous processing to increase efficiency and reduce operating costs.In later years, technological progress followed advances in materials of construction and control systems. Current innovations include large-scale equipment, high-capacity thickeners, belt type filters and Steller, candle-type filters for plants using zinc dust precipitation. As well, environmental protection is increasingly a major concern.The technology of gold adsorption from cyanide solution onto activated carbon has made rapid strides in recent years. This has followed the initial efforts of Potter, Salisbury, Zadra and their colleagues of the U.S. Bureau of Mines Research Station in Salt Lake City, Utah, and the field work of Homestake Mining Company personnel, in Lead, South Dakota."

Jan 1, 1989

By M. G. Rylatt, G. M. Popplewell

"Production from Canada's first diamond mine is planned for the last quarter of 1998. The climatic conditions and the variation in kimberlite types to be treated have lead to the development of a compact and flexible processing plant.High kimberlite moisture contents and winter temperatures below -40°C have dictated a process flowsheet with limited in-circuit storage to reduce materials handling difficulties. The latest developments in High Pressure Grinding Roll technology will be used to liberate the valuable diamond, reduce diamond breakage, and increase fines production to reduce the amount of material for down stream processing in the Heavy Medium Separation section.A varying heavy mineral concentrate yield has lead to the development of a final Recovery section that will incorporate Attrition Milling and Wet High Intensity Magnetic Separation for concentrate reduction. The latest developments in diamond X-ray sorting will be used to produce a final diamond concentrate for mechanical sizing, weighing and packing.Fine tailings thickening will utilise Deep Bed Compression type thickeners. This relatively new technology can produce;i) high underflow densities at low flocculant dosage rates, andii) clear overflowswith a smaller thickening area than conventional high-rate thickeners."

Jan 1, 1998

"Abstract - An estimation of resources of structurally complex gold lodes and stockworks represents a challenging task for geoscientists due to the complex geometry of the lodes and discontinuous grade. In the present case study, the resource of a gold stockwork has been estimated by uniform conditioning after the lode has been subdivided into geostatistically defined domains using the indicator probability model. The indicator probability model represents a powerful tool for structural interpretation of the mineralization and can be applied when traditional 3D volume constraining methods (wireframing) have failed to produce a unique, non-subjective model. For comparison, the resources of the same zone have been estimated without domaining. Results of the study clearly show that estimates obtained without domaining of the mineralization can yield a substantial error due to excessive smoothing of the grade.Application of uniform conditioning for modelling the grade distribution has a significant advantage over linear methods (e.g., ordinary kriging). Uniform conditioning enables estimation of local recoverable resources at different selective mining unit sizes that can be substantially smaller than the drilling density without creation of biases or over smoothed local values."

Jan 1, 2002

By G. R. Baiden

This paper discusses the application of Load-Haul-Dump (LHD) machine teleoperation in combination with a guidance system for single operator control of multiple IJIDs. A system accomplishing these goals has been tested at Copper Cliff North Mine of Inco Limited. This development uses a high-speed, high-capacity production network to teleoperate an LHD during loading and dumping by using 3D video and radio remote control. Following loading, the operator dispatches the LHD using an automatic guidance system to traverse the drifts to the orepass. Remote dumping is done at the ore pass and then the machine returns to repeat the procedure. This has significant productivity gains and improvements in safety. Productivity is improved because operators are involved only in the loading and dumping part of the process. This frees the operators to utilize their time more effectively, loading or dumping a particular machine, while other machines with guidance systems continue to work travelling and/or automatically dumping ore in the ore passes. Safety is improved as the operator is located on a remote control station. Automatic dumping will be incorporated as a future development.

Jan 1, 1994