Search Documents

By Narasimha Mangadoddy, Balraju Vadlakonda

"Bubble size distribution, bubble rise velocity and gas and solids hold-up are the key major hydrodynamic parameters that are extensively used for column flotation design and performance evaluation. The distribution characteristics of mean gas hold-up is studied using electrical resistance tomography (ERT) coupled with pressure transducers (PT) in column flotation. The ERT technique facilitates non-invasive and nonintrusive visualization of different flow regimes even in the presence of particles in a column flotation. The effect of superficial gas velocity, feed flow rate and slurry height in the column on mean gas hold-up and its radial distribution has been analysed for both two-phase and three phase flows. Experimental results show ERT coupled with PT is suitable as an online monitoring tool to provide useful information on the three-phase flow hydrodynamic parameters of the column flotation. The tomography images, which were generated using a modified sensitivity back projection algorithm, are employed to explore the influence of parameters in two phase flow in column flotation. Mean gas and solids hold-up values extracted from ERT have been critically analysed for the column operating in various flow regimes. Gas hold-ups and solid hold-ups results using ERT are in very good agreement with conventional estimation and correlations obtained using pressure transmitter methods. Meanwhile, the results show that the gas hold-ups in the centre region increase constantly with an increase in the superficial gas velocity, whereas solid hold-ups distribution is very heterogeneous for high gas velocity. Furthermore, the results also indicate that ERT is a very powerful tool for diagnosing the 'inside' flow behaviour of gas –liquid–solid three phase flow in columns operating for a wide range of flow regimes.INTRODUCTIONColumn flotation is perhaps the most significant technological innovation in flotation machinery and its successful introduction in mineral processing plants. There has been a lot of attention in understanding the various mechanisms that take place during operation. Due to many reasons column flotation has been found to yield better performance than conventional flotation cells, particularly with fine particles (Honaker & Mohanty, 1996). Due to complex flow behavior in nature, the performance of column flotation influenced by on flow characteristics of the process, (Jena, Biswal, Das, & Reddy, 2008). Previously basic research is carried out to evaluate the effect of the hydrodynamic parameters on performance of column flotation (Finch, J.A.;Dobby, 1991). Many techniques have been developed that could be used to experimentally analyse the hydrodynamics of column flotation. Tomography techniques are well sound to investigate the hydrodynamics for process equipment. Among that, Electrical resistance tomography (ERT) has been used in various industrial investigations for visualization of the concentration profiles and characteristics of the fluid dynamics in gas–liquid two-phase systems (Wang, Dickin, & Mann, 1999; Williams, R.A; Wang, 2000). ERT is an imaging technique to analyse the internal flow behavior non-intrusively. ERT provide very useful tools for measuring and monitoring of column flotation process on line. Due to its high speed capability, low cost measurement, robust sensors, ERT is considered to be the most powerful tool among other tomography techniques such as positron emission tomography (PET), magnetic resonance imaging (MRI), optical and infrared tomography. Application of ERT has extended in process systems due to its improved speed of data acquisition, sensitivity, flexibility and noise immunity. In multiphase flow of bubble columns, gas hold-up and solid hold-up are explored by using the coupling of ERT and difference pressure method (Jin, Han, Yang, & He, 2010)."

Jan 1, 2016

By A. Brown

The swift decline of coal during the period of unprecedented expansion in the Canadian economy is a phenomenon deserving careful examination, because the underlying forces contributing to this decline may have broader implications in our national economy. At the present level of technology, coal is more difficult to process, transport and utilize than liquid and gaseous fuels. Fundamentally, it is a matter of limitation in technique. Because coal is a vast store-house of energy in Canada, the reduction of these limitations is in the long-term national interest.

Jan 1, 1967

By Maurice A. Roche

Introduction Most of the Flin Flon ore-body, like many others in northern Canada, was covered by water. The original discovery was made where the ore-body outcropped on a strip of land jutting out into Flin Flon lake. The outcrop could be traced for a distance of 600 feet across the strip of land, but disappeared under the lake on both sides of the peninsula. Following the discovery or location of the property, in 1915, and subsequent to its examination by the H.P. Whitney interests in 1925, an extensive diamond-drilling programme was completed, which proved the existence of an ore-body at least 2,600 feet long and 900 feet deep. In plan, the central part of the ore-body at surface attains an overall width of about 450 feet; including waste horses, and gradually becoming narrower to the south. To the north, it stretches out as a much narrower tongue. The main body is a solid sulphide ore containing gold, silver, copper, and zinc. Adjacent to, and on the footwall side of, the solid sulphide ore-body, there are considerable widths of talcy disseminated copper ore, particularly in the upper 300 feet of the deposit, where the maximum widths occur. The ore-body occurs in a greenstone area, the rock being quite hard on the hanging-wall side, with the footwall schisted, talcy, and much softer. The greater part of the ore-body was overlain by 12 to 15 feet of water and from 15 to 90 feet of mud and clay, this material requiring eventual removal, regardless of the system of mining adopted. The total of mud and clay overburden was estimated at 1,000,000 tons. After considerable study, it was decided to mine the upper 300 feet of the ore-body by open-pit methods; the balance of the ore to be recovered by underground mining . The present paper gives an account of the methods adopted in both operations, and of the problems encountered.

Jan 1, 1935

By M. Mirzazadeh

Air cooled crackable and conventional forged steel specimens were tested under reversed push-pull conditions to examine the effect of shot-peening on their high cycle fatigue behaviour (-106 cycles). The steels were tested in the normalized as well as shot-peened conditions. The results showed that shot-peening smooth specimens had little effect on the fatigue limit of the air cooled forged steels and the detrimental effect of the rougher peened surface was not apparent. Microhardness profiles indicated that the shot peening produced a gradient of compressive residual stresses that was greater than that of the loading stresses, suppressing the anticipated beneficial effect on fatigue life. Crack initiation was more likely to occur below the surface. The results indicate that the surface roughness was not a significant factor in controlling the fatigue lives, since they were essentially the same for the non shot-peened and shot-peened steels.

Jan 1, 2010

By Masashige Makifuchi, Hiroki Kumakura, Kota Nagai, Takahiro Kikuchi

"A large amount of platinum group metals (PGM) are used in automobile catalyst. It is important to recover the metals from wasted catalyst. Nomura and Kageyama (2013) suggested recovery process that PGM oxides were absorbed to perovskite-type oxide based on LaScO3. In their process, the PGM in wasted catalyst as absorbed to the perovskite-type oxide as PGM oxide. It has potential to each element in the process if the perovskite-type oxide is selected properly. In this study, the PGM oxide absorption properties of various perovskite-type oxides are investigated to develop a new recovery and separation process. The various perovskite-type oxide were synthesized with metallic platinum, palladium, rhodium at high temperature in air atmosphere. And the PGM contents in the perovskite-type oxide after the experiment are determined by chemical analysis. Some of them have the properties to absorb specific PGM oxide selectively. In addition, in order to increase the amount of absorption of PGM oxide and composition of the perovskite-type oxide experimental temperature was investigated. Then it is also found that doping another specific element to the perovskite-type oxide is effective to increase the amount of absorption of PGM oxide. Then a new recovery process of PGM from wasted automobile catalyst, in which PGM can be separate to each element, was designed.INTRODUCTIONA large amount of Platinum (Pt), Palladium (Pd), and Rhodium (Rh) are used in automobile catalysis (Figure 1) (Platinum, 2013). Natural supplies for these metals are limited and PGM mining can detrimental environmental impact. Therefore, the recycling of PGMs from wasted automobile catalysis is very important. The Rose process (Figure 2) was developed as a process to recover PGM from wasted automobile catalysis. In this process, the automobile catalysis is first crushed mechanically, and then extracting agent, copper (Cu), and flux are melted at high temperature. The mixture separates into a metal phase, (Cu alloy containing PGM) and slag. The PGM is enriched by oxidizing. Cu to Cu oxide. The PGM are then recovered and separated to each element in a wet process. However, it is hard to dissolve the PGM with acid because they are chemically stable and strong oxidation agent such as aqua regia is used. Moreover, to separate the PGM to each individual element, a solvent extraction process is required."

Jan 1, 2016

By Ursula M. Franklin

Old iron nails are one of the most common objects which entice the general public to ask questions about the history of metallurgy. There is a lot of history in old nails - history of the manufacturing industry, and social and economic history. Nails, therefore, are fine teaching tools; whether students have to acquire metallurgical skills or explore the structure and properties of wrought iron, whether they want to look into the history of inventions and the development of machinery, studying nails tells a story better than any teacher or any book. I have used this approach often and the following note is based on several student projects, particularly the work of Carmina Herrero and Vicky Marchant. Nails, those essential metallic fasteners, have long been with us. Their size, shape and design is basically a compromise between the makers' ability to control and manipulate material and the demands of the intended application. There were copper and bronze nails in antiquity, but in this paper I want to deal only with iron nails. In Rome, iron nails were common, and Cleere carried out the fine metallographic investigations on a large stock of nails recovered from a Roman fort site in Scotland. Those nails were hand forged; sorting them at the site on the basis of length, shape of head and shape of shank (in cross section) indicated that there seemed to have been some nail standardization. It appears that the Roman smiths used a series of heading dies starting with a 1/s-in. size. Each successive size increased by approximately 1/16-in. The metallographic inspection of the microstructures of the nails showed that the smaller nails were made in the one operation; i.e. both the tapering and the formation were accomplished on the heated rod without reheating. However, in the case of the larger nails, the nail had to be reheated for the tapering after the head had been forged. Most nails were tapered on all four sides of the shank and the shanks were square in cross section; only one group had rounded shanks. Most heads were flat disks, but in one group the heads were pyramids and another group had conic heads. Figure 1 shows the procedure used to produce the pyramidal heads. Obviously, Roman nail making was sophisticated and each nail design was meant for a particular use.

Jan 1, 1999

By M. Pelser, H. Gous, J. H. W. M. Brits, K. Voogt

The effect of impurities; iron and selenium, on current efficiency and deposit quality in copper electrowinning was investigated using an at-line cell at the Rustenburg Base Metals Refiners’ Copper Tankhouse. The tankhouse is a direct leach, starter sheet electrowinning operation with a unique electrolyte composition. The effect of iron on the current efficiency in the at-line cell was found to be less severe than reported in literature. However, the distinction between the chemical impact of iron on current efficiency and the physical impact of iron on a starter sheet operation needs to be realised. The effect of selenium on current efficiency and deposit quality is also reported. INTRODUCTION Anglo American Platinum’s Rustenburg Base Metals Refiners’ (RBMR) Copper Tankhouse serves a unique function in the refinery flowsheet in that its primary functions are the removal of copper and production of acid for the leach circuit. This function needs to be performed to specification in order to keep the leach circuit operating optimally. Current efficiency is seen as an indicator of tankhouse performance and efficient energy use. The tankhouse plates starter sheets onto titanium blanks which, after stripping and preparation, return into the production cells for further plating. Approximately 78% of tankhouses surveyed (Robinson et al., 2013) use permanent cathode technology whereas older, smaller operations still use starter sheet technology. Drawbacks of the starter sheet technology are that the starters are thin and bend easily leading to increased shorts, they need to be removed after two days of plating to be manually straightened and are then returned to the cells. In addition, the electrolyte levels in the cells need to be adjusted during the plating cycle to improve loop adhesion to the cathode and reduce loop corrosion. The starter sheet technology is therefore very labour intensive and the final quality of the product is dependent on the quality of the starter sheets produced. In comparison, permanent cathode or direct plating technology lends itself to automation, allows for higher current densities and better cathode quality due to more robust geometric stability in the cell. The present barrier to implementation of permanent cathode plating at the RBMR Copper Tankhouse is the capital cost required to convert the tankhouse, i.e. blanks and stripping machine. At present, alternatives to titanium blanks, such as LDX 2101, are being investigated for the unique electrolyte composition of this tankhouse.

Jan 1, 2019

By Kadir Sariiz

Abstract - The Akçayir-Yürükakçayir Miocene-Pliocene basin in the Central Anatolia hosts ancient lacustrine sepiolite deposits. The succession in this basin consists of conglomerate (Yürükakçayir conglomerate), clayey and silty limestone, dolomitic marl, sepiolite beds and lenses, and dolomitic limestone (Kepeztepe formation). The main impurities within the sepiolite rock are dolomite, opal-CT, calcite, smectite and feldspar as sepiolite + dolomite and sepiolite + opal-CT are the main mineral assemblages. Smectite and feldspar are thought to be of detrital origin. Calcite is found as a secondary filling in root tubes and casts. Sepiolite samples studied display root-marks and root tubes, soapy and massive structure indicating direct precipitation. Sepiolite deposits probably formed at a pH of 8 to 9, and Mg+2 and SiO2 concentrations in moderately saline environments of internal facies of an alkaline lake.

Jan 1, 2000

By Laura A. Sanders

Mineral scale formation is prevalent in numerous mining operations. Such scale formation can occur in the direct-contact heat exchangers ahead of an autoclave. In these heat exchangers, the incoming slurry comes into contact with steam in a stage-wise fashion, which is re-circulated from the downstream flash vessels to heat the slurry in stages ahead of the autoclave. Calcium sulfate scaling causes severe problems in mining operations where increased temperatures are involved due to rising temperatures promoting calcium sulfate scaling through a decreasing solubility. In a number of these operations, the scale formation can occur in the presence of mineral solids, where fine-grained charged particles are at concentrations in excess of 35%. Scale prevention is not difficult in standard aqueous systems; however, the presence of solids leads to significant deficiencies in the prevention of scale due to the adsorption of the polymer onto the charge solids instead of the polymer interaction with the scale. Therefore, a technical solution to prevent mineral scale build up occurring in presence of pulp slurry in mining operations is needed. Several novel antiscalant technologies were developed and evaluated which provided a substantial improvement in the scale prevention in such systems.

May 1, 2013

By Karl Dufresne

Blasting in geothermally high temperature ground and/or extremely reactive ground is an increasing common challenge for surface and underground mines. Many current PETN based non-electric and electronic detonators have manufacturer published in-hole temperature limits ranging from 55°C to 65°C (131°F to 150°F). When confronting blasthole temperatures above the manufacturer published limits, operations may request site-specific guidance and qualification for use. The advised safe loading window for in-hole PETN based detonators is often too short to be practicable for production blasting. To overcome limitations of PETN based initiation systems, surface mines with high temperature ground and/or reactive ground are known to load blastholes with a qualified high temperature bulk emulsion that are top primed with a cartridge of temperature qualified detonator sensitive emulsion plus an RDX detonating cord downline. As there is no in-hole delay detonator in this system, blasthole timing is accomplished with surface delays. Although this system is safe, top priming and surface delaying does influence floor quality and top size fragmentation, and safe loading windows times reduce blast block size and increase blasting frequency. A mining company with a site characterized by geothermally high temperature ground plus highly reactive ground employed a blasting system like the one described above. The site desires to improve blasting performance by moving to an in-hole delay initiation system that can withstand the site ground conditions. At the request of the mining house, DynaEnergetics developed an electronic initiation system for application in geothermally high temperature ground and/or extremely reactive ground conditions. The DynaEnergetics IGNEO high temperature electronic initiation system is rated for in-hole use in ground up to 150C (302°F) for 48 hours. The detonator consists of a high strength detonator with an HMX base charge and thermally resistant downline. To make up a primer, the detonator is inserted into a booster charge assembly that is fitted with a small HMX shape charge. This high energy primer is designed to be compatible and reliable for firing bulk emulsions, including those with high percentages of urea inhibition to combat reactive ground. Up to 1000 detonators may be programmed in 1ms increments up to 1500ms. The system is controlled by a digital firing panel that can be used with either a wired or wireless trigger.  The system enables high temperature and/or reactive ground sites to utilize in-hole delay initiation and realize the associated performance benefits. Conclusions and Future Work 1] The HMX based electronic initiation system permits bottom in-hole delaying in ground temperatures above 80°C (175°F). As compared to top priming and surface delaying, in-hole bottom delaying is known to improve floor quality, muckpile fragmentation uniformity and reduce oversize. 2] Field evaluation of the HMX initiation system at the Lihir Mine is continuing. 3] Work on the next generation of the HMX initiation system is underway and will bring with it expanded application range and flexibility. 

Oct 1, 2024

By John F. Gartner

"Traditionally, the geologists of Canada have been occupied with the tasks of finding new mineral bodies, locating gas and oil fields or hunting for economic deposits of industrial minerals. A very minor percentage of graduate geologists have applied their skills to solution of the ""urban blight"" or employing their understanding of ""Nature"" for the optimum use of land by mankind. However, things are changing quickly. The role of the geologist in the planning process is being established. It is an exciting time! Geologists are now being consulted on a wide range of urban planning problems. These vary, tor example, from assessment of the geological environment for the new communities of Erin Mills and Meadowvale, which will have total populations in excess of 100,000 people (truly a satellite city), to a complete geological/ geohydrological assessment of the new sanitary landfill for the city of Guelph.Use of geologic techniques and methods for urban studies must be enhanced with certain skills not taught, in the past, to the geologist. These include airphoto interpretation, soil mechanics, geohydrology, municipal engineering and highway engineering to mention a few. The geologist has the unique training to assess the natural environment and to discover, warn and explain the implications of man's attempt to command his environment."

Jan 1, 1972

By S. Perez

Core drilling is a fundamental process in the mineral exploration industry. As deep exploration in hard rocks is accelerated due to the depletion of near ground mineral resources, deep-drilling operations need to reduce their reliance in operators experience and begin to implement new technologies in order to increase efficiency and cost-effectiveness of the overall process. Currently, lack of real-time information on the bit/rock interaction is a major problem. Therefore the mechanism behind the acoustic emission, which is a proven technique for remote monitoring, generation in mechanical rock cutting must be understood in order to provide real time information about the rock. This paper aims to identify the influence of mineral composition of granitic rocks on the acoustic emission (AE) during rock abrasivity test with a single contact tool and to evaluate the feasibility of AE as a means to infer Cerchar Abrasivity Index (CAI). Single contact tool will provide precise and accurate description of the source of AE. To provide constant grooving speed Cerchar apparatus was modified to monitor AE during rock/tool interaction. Tests on the modified Cerchar apparatus are carried out under the static load of 70N and cutting speed of 1 mm/s. A Scanning Electron Microscope (SEM) is utilized to visualize the groove in the rock and to identify the mineral composition through Back-Scattered Electrons (BSE) reflected from the rock sample. Based on the microscope images, it was found that biotite shows a larger groove area and plate-like fractures accompanied with burst-type AE signal, whereas plagioclase and quartz, which are characterized by similar hardness and BSE brightness, possess shattered-like fractures and more continuous-type AE signals. In addition, a-value of the Gutenberg-Richter scale has been found to well correlate with Cerchar Abrasivity Index (CAI).

Jan 1, 2015

By H. A. ?ye

The ISO TC 226 (Materials for the production of primary aluminium) has presently issued more than one hundred standards on the materials: alumina, pitch, petroleum coke, carbon anodes, carbon cathodes, ramming paste, fluorides and refractory). The object of the standardization work is to find methods that both material producers and smelters will accept. Methods that are specific for the operational conditions have been developed in addition to more traditional room temperature methods. Examples of important properties under operational conditions are: Air and C02 reactivity of anodes, Equivalent temperature for baked anodes, Sodium expansion of cathode blocks, Shrinkage and Rammability of paste, Penetration of electrolyte into refractories.

Jan 1, 2006

By F. Channier

The paper provides the most recent information on the construction of the AP60 phase 1 plant of Jonquiere which is due to be commissioned and started up in the first quarter of 2013. HSE management on site by RTA, and cooperation with local equipment manufacturers and contractors of the Saguenay-Lac Saint Jean region are highlighted in this section. The AP60 phase 1 Jonquiere plant aims to demonstrate of the AP60 technology at an industrial scale and allows the further developments of the AP60 cell. The advantages of the AP60 cell technology in terms of productivity, power consumption and environmental footprint are also briefly presented in the paper.

Jan 1, 2011

By M. R. Hudec, M. A. Nikolinakou, P. B. Flemings

"We model the shale response to the large deformations associated with salt bodies, and we identify the implications of the stress changes for hydrocarbon exploration. We employ both the static and evolutionary approach, and show that while the static one can model actual geologic geometries, only the evolutionary approach can provide a detailed description of the stress history of shales, which is essential for predicting stress, porosity, and pore pressure and, more generally, for understanding Earth processes related to salt-hydrocarbon systems.INTRODUCTIONDuring the last two decades, understanding the stress, material behavior, and pore pressure in shales around salt bodies has become increasingly important. The energy industry routinely drills near salt (Beltrão, Sombra, Lage, Fagundes Netto, & Henriques, 2009; Meyer, Zarra, Rains, Meltz, & Hall, 2005; Seymour, Rae, Peden, & Ormston, 1993), because a significant number of hydrocarbon reservoirs around the world are found in layers dipping away from salt diapirs.Salt is a viscous material that cannot sustain deviatoric stresses. Under differential loading it flows, changes shape, and eventually relaxes to an isostatic stress state (Urai & Spiers, 2007). Therefore, emplacement of a salt body and its viscous relaxation process may cause significant deformation of the surrounding sediments, perturb their state of stress and create local overpressures (Dusseault, Maury, Sanfilippo, & Santarelli, 2004; Seymour et al., 1993). As a result, drilling near salt is particularly challenging, and problems leading to additional expense or even abandonment are common (Bradley, 1978; Dusseault et al., 2004; Meyer et al., 2005; Seymour et al., 1993; Willson et al., 2003).Historically, salt and the evolution of its cross section to the present day geometry have been studied using kinematic restorations (Rowan & Ratliff, 2012). This approach aims to explain the present geologic section through a sequence of plausible past sections; however, it does not model the constitutive response of the wall rocks, hence it cannot provide any prediction on their state of stress. Similarly, largestrain numerical studies (Albertz & Beaumont, 2010; Chemia, Schmeling, & Koyi, 2009; Goteti, Ings, & Beaumont, 2012; Gradmann, Beaumont, & Albertz, 2009) have focused on the rheological evolution of salt systems without modeling the geomechanical response of the sediments."

Jan 1, 2015

By L. Gasser, N. Bellinger, H. Awatta, A. Merati

As aircraft age, the extent of interactions between fatigue and other damage mechanisms, such as corrosion and fretting, increases. At present, however, there is no generally accepted methodology within the Aircraft Structural Integrity Program (ASIP) framework to account for the effects of these interactions on life and the residual strength of aging aircraft components. A comprehensive program is being carried out by the National Research Council Canada in collaboration with Analytical Processes/Engineered Solutions, using the Holistic Structural Integrity Process (HOLSIP) to address time and cyclic load issues. This approach predicts the evolution of a discontinuity state in a material from production to retirement. This paper summarizes the results of a study on the 2024-T3 aluminium alloy in different forms (clad and unclad), thickness, and specimen geometry. This study consisted of identifying the microstructural features associated with crack nucleation sites and relating them to the testing parameters and fatigue life. Several coupons were fabricated and fatigue-tested. The fracture surfaces were carefully examined, and the physical characteristics of the microstructural features found near the crack nucleation sites were analyzed. Effect of stress level, loading direction, coupon geometry and surface condition on the number of crack nucleation sites, and fracture origin size has been discussed. Four distinctive mechanisms were found to be responsible for crack nucleation: for unclad materials constituent particles, oxide residue, surface irregularities and for clad samples the clad layer was the sole fracture origin.

Jan 1, 2006

By G. Anger, J. Enser, H. Antrekowitsch, S. Koch

Homogeneous chemical composition and microstructure are always necessary, but not always attained in practice. As-cast aluminium alloys tend to have a segregation microstructure. Features of the cast structure, which affect subsequent processing or properties, can be altered by the homogenization. The main task of the Department of Nonferrous Metallurgy was to investigate the effect of homogenization treatment on precipitation hardening of aluminium alloys 6061 and 6082. The effect of the solution heat treatment (SHT) temperature on the mechanical properties was also analyzed. The homogenized and non-homogenized rolling slabs were produced according to the usual conditions and methods. The metallographic investigations were carried out on the as-cast samples, after homogenization, after the hot and the cold rolling mill, and after natural and artificial ageing. Then, Brinell hardness measurements and tensile tests were conducted on both alloys in order to examine the influence of the homogenization.

Jan 1, 2006

By N. J. Shackleton, N. A. Chapman, V. Malysiak, C. T. O’Connor

In this study, the effect of using conventional crushing and high-pressure grinding rolls (HPGR) in combination with dry or wet milling was investigated using a base-metal sulphide (BMS) sphalerite and a platinum group mineral (PGM) ore to determine how these processes affect the flotation performance. In sphalerite, irrespective of the crushing procedure (HPGR or conventional), dry milling resulted in the highest grades and recoveries of zinc, whereas in PGMs, similar treatment produced the poorest results. The results were investigated further by the effect of factors such as percentage liberation and particle size on the flotation results.

Jan 1, 2012

By N. Aydogan, H. Dundar, Å. Partapuoli, A. Fredriksson, P. Wikström, K. Tano, G. Adolfsson

The Autogenous milling of ores holds an increasing attraction as the focus moves towards reducing energy usage, both direct and embodied in grinding media. However, most of the early AG mills were converted to SAG for improved stability and increased throughput. This imposes a huge penalty in steel grinding media consumption. The LKAB iron ore operations in Sweden process highgrade magnetite through fully-autogenous milling lines to a final product P80 of about 45µm. The outcomes of P9O AMIRA research surveys, covering a wide range of mill fillings and throughputs and with different feed blends, are presented. Insights are provided on operational strategies, opportunities, the influence of feed size control and balancing the blend of competent gangue and softer magnetite. Areas of importance in the successful operation and control of energy-efficient autogenous circuits are highlighted.

Jan 1, 2012

By P. Coursol

The Noranda Reactor Process (NRP) has been in operation now for more than 30 years and this mature process has attained a high level of performance. The NRP at the Home Smelter of Xstrata Copper treats a wide range of feed materials and a thorough knowledge of both process control and smelting physico-chemistry has been beneficial to help meet the required plant flexibility. In this regard, some level of predictive knowledge related to slag chemistry, in particular, the liquid and solid phases such as spinels or olivines, has been found to be beneficial. In the last decade or so, the availability of commercial thermodynamic modeling packages, such as Factsage1m have been utilized with advantage to help the plant optimize slag chemistry and minimize problems from difficult slags, for example, those the could arise from undue feed variability. This paper illustrates the application of this software in examining a range of operating parameters such as: %Fe in product matte, the %Fe/%Si02 ratio in the slag, the levels of minor slag components including CaO, Ah03, ZnO, and MgO, and the level of oxygen enrichment on the operating conditions of the NRP. The slag composition boundaries at the conditions affecting magnetite control and solid magnetite/other precipitated solid phases, as well the conditions influencing the slag liquidus ranges of NRP slags are also discussed with respect to the overall process chemistry.

Jan 1, 2007