Search Documents

By Matthew S. Hall

Gold/iron oxide catalysts have been prepared and their catalytic performance evaluated for low temperature CO oxidation. The method and temperature used to dry the sample has a significant effect on their catalytic activity. Analysis by TEM revealed the catalysts contained Au particles, although catalysts with high and low activity did not always differ in their microstructure as evidenced by TEM. Catalysts were characterised using XPS and the difference between the Au(4d) and C(1s) binding energies measured; in general the greater the difference, the higher the catalytic activity of the material.

Oct 1, 2003

By Graham E. Brown

Since the beginning of time, people later to be known as engineers and architects have strained to create methods whereby they could improve technology to assist them in their various fields of endeavour. Some of these improvements would be the change from linen paper, french chalk and ink pens to drafting film , mylar an d pencil for the production of drawings, the drafting machine in lieu of the tee and set squares, even tap e to attach drafting media to the board instead of thumb tacks and man y, man y more. All of these taken individually are insignificant but combined evolve to the current state-of-the-art in the computerized engineering environment. Ten years ago the major topic o f conversation was the hand-held calculator which for a cost of around $150 would give most trigonometric functions. Today the equivalent calculator can be purchased for around $25, is about one third the size, and if inflation were included over the last ten year s the item should cost around $550 in today' s dollars, it can be seen that tremendous advances not only in the technology but also the cost saving. The following paper is intended to outline some o f the significant aspects o f the latest technology in the computerized engineering office namely Interactive Graphics Systems.

Jan 1, 1985

By James L. Parks, David M. Kjos

"Designs, installation procedures and performance characteristics of martensitic cast steel concaves are reviewed. Longer wear life, fewer pieces to install and eliminating the need to scarf joints are the principal benefits of using martensitic steel to replace austenitic12% Mn (Hadfield's) steel, the traditional concave material for large gyratory crushers. Installation procedures that reduce the risk of breakage are described. Operating practices that affect concave performance are also discussed.IntroductionThe crushing machine considered to be the forerunner of the modem gyratory crusher was patented in 1878 by Charles M. Brown of the Gates Iron Works(1). The earliest gyratory crushers with receiving openings of 6 to 12 inches were fed by hand, and the crushing capacity of a mine was increased simply by installing more small crushers. The introduction of the steam shovel to open pit mining around the tum of the century provided an incentive for much larger primary crushers, and gyratory crushers with a 48 in. receiving opening were being built by 1910, followed not long afterward by machines with 54 in. and 60 in. openings to . Fortunately for the crusher maintenance people of that era, an austenitic 12% Mn steel with exceptional toughness was already available, having been discovered by Robert Abbot Hadfieldoi in 1882. Although small gyratory crushers working soft- to medium-hard rock reportedly used chilled cast iron (white iron) wear parts, these newer and much larger machines were fitted with ""Hadfield's manganese steel"" concaves and mantles to withstand the impact associated with handling large rocks .M E International first challenged the long-standing convention of using 12% Mn steel concaves in large gyratory crushers in the late 1960s when they supplied upper row concaves in martensitic cast steel for a 60-109 primary crusher at a taconite plant on the Iron Range. Since then, martensitic steels have been successfully substituted for 12010 Mn steel in concaves for more than seventy primary gyratory crushers processing iron, copper and precious metals ores, industrial minerals and crushed stone.This paper reviews materials, designs and performance characteristics of martensitic steel concaves in large gyratory crushers. The principal benefits include significantly longer wear life, fewer pieces to install and the elimination of scarfing. Obtaining the full measure of these benefits and minimizing the risk of breakage is strongly dependent on installation procedures, which are described in some detail. Operating practices that can affect performance are also discussed."

Jan 1, 1993

By L. J. Bryson, C. A. Biley

"Anglo American Platinum’s Rustenburg Base Metals Refiners (RBMR) produces Ni and Cu cathode from slow cooled converter matte after Platinum Group Metals (PGMs) are magnetically separated for further processing. In 2010, execution of the RBMR expansion project was commenced to increase the production capacity to 33 ktpa Ni. The expansion, which is currently still in a ramp-up stage, brought about several fundamental changes to the circuit chemistry, including the installation of a dedicated Pressure Iron Removal (PIR) autoclave. This provided an independent outlet for iron from the refinery, which previously deported to the residue from the leach circuit and was toll refined. At the same time as changes in the circuit associated with the RBMR expansion were being made, the plant experienced a significant increase in iron and copper units per nickel unit in the feed. The decoupling of the leaching and iron removal process steps has had significant advantages for the robustness and control of the overall circuit, in particular pertaining to the preparation of a nickel electrolyte of sufficient purity to produce LME grade nickel. This paper details the primary changes to the RBMR circuit chemistry with a particular focus on iron deportment and the benefits derived from the installation of the PIR autoclave.INTRODUCTIONAnglo American Platinum mines and refines Platinum Group Metals (PGMs) through a complex processing pipeline in its South African operations. Mined ore is first treated through several mineral processing stages, geared to the recovery of base metals and associated PGMs, followed by smelting and refining operations that aim to separate base metals from PGMs and recover the value components to purified, saleable products. The focus of this paper is the Rustenburg Base Metals Refiners (RBMR) complex which receives a PGM-containing converter matte, then physically separates PGMs and base metals, and recovers nickel and copper to cathode by utilising leaching, precipitation and electrowinning processes.With new mining operations coming online and the continued increase in PGM ore arisings, it was necessary to undertake an expansion project at the Base Metal Refinery (BMR) to increase production capacity from 21 ktpa to 33 ktpa Ni. Complicating the expansion project was the requirement of continued production through all stages of design, construction and implementation and, due to stringent capital constraints, the utilisation of all existing equipment installed during a previous expansion in 1981. Against this backdrop, the expanded BMR flow sheet involved significant changes to the chemistry, especially iron management. These changes in iron management allowed for the separation of iron and copper residues and significantly increased the robustness of the plant to changes in feed mineralogy as well as the potential to increase production duties of the existing equipment."

Jan 1, 2016

By B P. Scott

Podsol soil horizons developed on Pleistocene glacial sediments overlying the Coronation Mine orebody were analyzed for copper and zinc spectro-photometrically, using biquinoline-isoamyl alcohol and dithizone carbon tetrachloride reagents. Copper and zinc are concentrated in the A. and C horizons, whereas the A1, A2 and B horizons are leached. Of economic significance is the fact that the C horizon contains a copper anomaly, in excess of 100 times back-ground, directly over the orebody. Due to the erratic distribution of high copper concentrations in the Ao horizon with respect to the orebody, that horizon is not considered as a reliable prospecting datum. U NDER certain conditions, metallic ore deposits are accompanied by primary halos of trace elements in unweathered rock surrounding the orebodies or by secondary halos in weathered rock, alluvium, soil, or vegetation above or near the mineralized zones. Where such halos occur, chemical analysis, as applied to the detection of trace elements, is a valuable prospecting aid, permitting the detection of mineralization of possible economic value.

Jan 1, 1965

By B. A. Monkman

"IntroductionONE OF :THE most effective methods by which the construction industry is combatting mounting building costs is by making increased use of lightweight materials, thus reducing the dead load to be carried •by structures. This applies to non-metallic materials as well as to metallic ones, and particular attention has been given to developing lightweight aggregates for use in concrete.The use of lightweight aggregates is not new and, in fact, dates back to the Roman Empire, when pumice was used in the walls and domes of the Roman buildings. More recently, and up to a decade or so ago, the demand for these aggregates was met from deposits of volcanic cinders, pumice, scoria, etc., and from the by-products of blast furnaces and coal burning boilers. However, these sources of supply are no longer sufficient to meet the demand, for transportation costs pretty well restrict the use of the natural lightweight aggregates to the western cordillera regions where the deposits of these materials occur, and the use of expanded slag aggregates to the areas neighbouring the plants where slags are produced. As for cinders, the supply has been greatly reduced by the conversion of industry to fuel oil, natural gas, and powdered coal, and the large stockpiles which existed previously have been pretty well exhausted.Industry's approach to the problem of a decreasing supply, in the face of an increasing demand, has been characteristically direct. The solution has been to construct plants whose sole .purpose is to produce economically an acceptable light-weight aggregate from materials close at hand."

Jan 1, 1955

By J. W. Reynolds

"The use of approved fire-resistant hydraulic fluids in equipment operating underground was made mandatory in British Columbia by amendment to the Provincial Mines Regulation Act effective January 1, 1975. This paper covers the action taken to achieve this, in the largest underground metal mine in British Columbia. Some evaluation of costs and effects based on experience to date is included.BackgroundAn amendment to the Mines Regulation Act of the Province of British Columbia was passed in July 1974 as follow s: "" Rule 111 (b) Hydraulic Fluids. After the first day of January 1975, all hydraulic fluids used in equipment operating underground shall be of a fire-resistant type accept able to the chief inspector.""Unquestionably, its intent was justified as a safety improvement measure. The list of fires in mines involving machinery where hydraulic fluid was a factor in the fires is long and sobering. In British Columbia, in a 22-month period from 1972 to 1974, there were six fires in metal mines resulting in extensive equipment damage and injury to four workmen. Nevertheless, no provision was made for research or development of systems modifications compatible with conditions encountered in B.C. and, as late as June 1977, the Mining Association of British Columbia continued to argue that fire suppression systems should be considered sufficient until a universal suitable hydraulic fluid could be developed. The sole concession was to issue permits for continued use of mineral oil in equipment bought prior to 1975 in order to allow producing operations to continue. The burden of developing the necessary technology was laid on the industry.The Sullivan Mine at Kimberley, the largest and longest established underground mine in the province, and Cominco's most important source of ore s for its smelter at Trail, B.C., was at the outset of a conversion from conventional to trackless mechanized mining methods in pillar recovery operation s. Introduction of fire-resistant hydraulic fluid s had to be done in a period of change, in many instances on equipment for which no data existed, and called for research which had to be done while retraining the work force.The introductory phase is complete. All equipment is on FRF, the requirements of Rule 111(b) are being satisfied, and a number of research and development programs continue."

Jan 1, 1980

By C. C. Li

The D bolt is a new type of energy-absorbing rock support element recently developed in Nor-way. The D bolt is not only able to accommodate large rock deformations, but can also provide a load-bearing capacity as high as that of rebar bolts. Furthermore, the anchoring quality of the D bolt is similar to rebar bolts because of its multi-point anchoring design.

May 1, 2009

By Michael Cullen

The Quinsam Coal Mine is in the process of extracting a panel beneath the mine access road. To prevent damage to the road, and adjacent powerline, it was necessary to establish a ?protection zone? within which the extent of mining would be limited. The protection zone is analogous to the setback limit. For economic reasons it was desirable to make the protective zone as small as possible, and with the greatest extraction ratio possible. The size of the protective zone was established by determining the angle of critical deformation using the numerical model FLAC, coupled with field data on subsidence from the Mine. The angle of critical deformation (defined as the angle, measured from the vertical, at which intolerable damage is sustained by a structure) was determined to be between 0 and 5 degrees. The allowable extraction ratio in the protection zone was established using the ARMPS method of pillar design coupled with field data on pillar stability from the Mine. Excavations spans to prevent caving were determined by historical experience and field data on span stability from the Mine, coupled with numerical modeling. The minimum pillar size was determined to be 7.5m. The maximum pillar height was established at 2.5m. The maximum allowable excavation span was determined to be 8.5m. With these criteria, extraction ratios between 54 and 73% (measured in plan view) were determined to be appropriate for the protection zone.

May 1, 2001

By F. Habashi

"While bioleaching of pyrite concentrates has been successfully used in industry to liberate gold from the sulphide matrix for subsequent cyanidation, the same technology cannot be recommended for leaching chalcopyrite concentrates for copper recovery. It will be shown to be uneconomical and cannot compete with pressure leaching technology. Data on the pilot plants that were constructed for this purpose and were shut down will be given.INTRODUCTIONBacterial leaching has been successfully applied for heap leaching of low-grade copper ores (Habashi, 1978, 1999). One of the major operations is that at Bingham in Utah (Figure 1). The leach solution collected at the bottom of the heap is extracted by organic solvents and the strip solution is electrolyzed to get high purity copper. The process was extended to treat auriferous pyrite concentrates to liberate gold and render it amenable to cyanidation by a process known as BIOX (Marsden & House, 2006; Lunt & Briggs, 2005).BIOX plants currently or recently in operation are the following:??Ashanti Goldfields Company, Ghana. Designed with an initial capacity of treating 720 tonnes of concentrate per day, the Sansu plant has since been expanded and currently has four modules processing 960 tonnes per day in all. It is by far the largest biooxidation plant in the world. The capital cost of the plant totalled US $25 million (1994 terms) and the operating cost is currently US $17/tonne milled.??Fairview, South Africa. The plant at the Fairview mine in Barberton, which was the initial pilot plant, has been fully operational since 1986. It was originally designed to treat 10 tonnes/day of concentrate but with the success of the project this has been increased to 55 tonnes per day. With the purchase of Fairview by Avgold’s Eastern Transvaal Consolidated, Avgold concluded a licensing agreement with Gold Fields, formerly known as Gencor, entitling it to use the BIOX technology to treat itsconcentrate.??Saõ Bento, Brazil. A BIOX plant was recently in operation in Brazil at the Saõ Bento Mine where a pressure oxidation circuit is used to treat the refractory flotation concentrate. This plant has confirmed the viability of combining bio-oxidation with pressure oxidation as a cost-effective method ofincreasing capacity at an existing oxidation plant.??Wiluna, Australia. The plant at Wiluna Gold Mine, Western Australia, was commissioned in 1993. Although originally designed to treat 115 tonnes per day of concentrate this has subsequently been increased to 158.??Other plants at Tamboraque in Peru, Harbour Lights and at Youanami in Australia have been commissioned recently."

Jan 1, 2012

By J. Duby

"A description is given of a series of tests performed to determine the comparative effects which dynamic and static straining, in compression, have on the physical strength properties of mild steel and an aluminum alloy. The dynamic deformation was imposed during the passage of single stress pulses of about 100 micro-second duration. These pulses were recorded with strain gauges mounted near both ends of the specimen. The resulting records were analysed using a simple wave theory; there from the dynamic stress-strain curves for the respective metals were deter-mined and were then compared with the static stress-strain relation. The respective hardnesses of the metals after deformation are evaluates by means of static stress-strain curves in compression. The micro-structures of the metals before and after deformation are also shown. It is observed that dynamic de-formation considerably modifies the rate of strain hardening. This modified hardening appears to be persistent. The observed differences in physical strength properties and micro-structures are discussed in the light of the accepted dislocation theory for metals."

Jan 1, 1960

By Brian E. Robertson

"This paper summarizes work carried out at the Dome Mine to mechanize the mining of narrow veins of less than 1.5 m in width by the introduction of new mining methods and specifically designed electric LHDs.Extensive mining trials have been conducted using sublevel blasthole, modified Avoca, and resuing mining methods. The introduction of the Microscoop and the Jarvis Clark remote, radio-controlled scooptram has increased mucking productivity.As a result of this work, additional narrow vein stopes are now being prepared for production. In the future, narrow vein stoping wil lprovide a greater percentage of the total mill tonnage.IntroductionThe Dome Mine, which is owned and operated by Dome Mines Limited, is located at Timmins, Ontario. Production has been continuous since 1910 and in 1984 was increased from 1814 to 2721 tonnes per day.At least six distinct ore types have been recognized at the mine. In general, these orebodies can be broadly categorized into wide and narrow deposits. The wide deposits are approximately lenticular in shape and vary in width from 10 m to 40 m. The narrow orebodies consist of quartz and quartzankerite veins ranging in width from a few centimetres to six metres. The average dip of the veins is 65 degrees.Since the I970s, mining activity has been largely concentrated in the wider orebodies using highly productive open sublevel blasthole and mechanized cut-and-fill stoping methods. With the demise of shrinkage stoping in 1975, investigations were initiated to develop new mining methods and introduce LHDs - truly designed for narrow orebodies. These investigations resulted in test trials of the sublevel blasthole, modified Avoca, and resuing mining methods. Consultations with equipment manufacturers and suppliers led to the development of the Jarvis Clark remote, radio-controlled electric scooptram and the introduction of the France Loader Microscoop."

Jan 1, 1986

By D. E. Macdonald

"Approximately 2.0 million tonnes of phosphate rock is imported from the U.S. to Alberta annually and is used in the production of agricultural fertilizers. No phosphate rock is presently mined in Canada, although sources of igneous phosphate have been mined in the past. Sedimentary phosphate rock is found in nine geological units within the Cordilleran Foothills and Front Ranges region of Alberta. The Devonian-Mississippian Exshaw Formation, Permo-Pennsylvanian Rocky Mountain Supergroup, and the Jurassic Fernie Formation have the best potential f or future development. Most of the phosphate rock in Alberta is of low grade and lies within restricted land use areas. The best over-all resource potential lies in the Fernie basin area of southeastern British Columbia, in the Fernie Formation. The possibility of deep phosphate rock deposits in the plains region should be examined.Phosphate rock is mined in Idaho, Utah, Montana and Florida, and is shipped to Canadian fertilizer plants for processing. Raw phosphate rock is acidified, usually with sulphuric acid, by a wet process. Varying amounts of ammonia are added, and the fertilizer is pelletized. Future research, in western Canada, is needed in the beneficiating of low-grade ores and in the area of in situ mining. At the present time, phosphate rock sells for around US$50Itonne, and Alberta fertilizer companies probably pay in the range of C$7D-$85Itonne for U.S. phosphate rock delivered to the plant. Environmental concerns about phosphate rock processing are centred around gypsum tailing ponds, and radioactive wastes.U.S. supplies of phosphate rock are secure until the year 2000; however, by this time, the richer deposits in the U.S. may be exhausted. Alternate deposits, such as the ones in Alberta and British Columbia, might then be considered. Phosphate byproducts, such as uranium, vanadium, fluorine and rare earth elements, may help in making the processing of low-grade Canadian phosphates economically feasible."

Jan 1, 1988

By W. B. Morrey

This paper deals with the development of the new cap-sensitive slurry explosives. The history and special features of these explosives are outlined, and recent field trials are described.

Jan 1, 1973

By T. Alan O'Hara

"Annual mining revenue can be computed by formulae relating metal prices, smelting schedules, concentrate grade and recovery to known ore grade and an assessment of core samples. Operating costs at different daily tonnages are related to orebody shape, mining method, milling process and general plant services. Capital costs are related to sizing of mining equipment, mine development, plant-site topography, climate and accessibility, plant services and personnel housing. IntroductionA crude guide to the average 1978 cost of mine projects is shown in Figure 1, but the costs of many mine projects have differed widely from the graphed average costs of $800,000 T0.6 for underground mine/mill projects and $400,000 T 0.6 for low-grade open-pit mine/mill projects.High mine project costs and high operating costs are characteristic of open-pit mines with high stripping ratios, underground mines with thin orebodies, mills with complex metallurgy, and projects located in isolated regions with severe climate, mountainous topography, and lacking access to existing roads, towns and electric power. When none of these adverse conditions prevailed, the mine project cost was typically much less than the graphed average cost. Virtually all the conditions likely to cause high capital and operating costs are known from knowledge of the local topography, climate or accessibility, or can be assessed by tests on core samples, as soon as the orebody has been outlined by drilling .A more accurate estimate of over-all project capital cost and operating cost can be made from a summation of items of cost after judging the effect of specific local conditions on each item of capital and operating cost. This paper offers guides in judging the effect of local conditions on the sizing and 1978 cost of specific items of capital cost and operating cost and operating cost of mine projects. When the specific items of capital cost and operating cost are totaled and measured against expected net revenue and taxes over the life of the mine using the net-present-value or discount-cash-flow methods, the result should show whether the mine project development is clearly feasible, doubtfully feasible or clearly uneconomic. If the development of the mine project is clearly feasible, or probably feasible, a detailed feasibility study by experienced consulting engineers should be commissioned before any financial commitments are made; but if project development appears to be uneconomic, the time and cost of a detailed feasibility study is not warranted."

Jan 1, 1980

By P. M. Tyroler, W. J. Thoburn, M. R. Alberty

"An initial test of this unique application demonstrated that hot gunned refractory would adhere satisfactorily. Subsequently, it was found that the proportion of material sticking during application increased with increased vessel temperature and when a mix containing pitch was used. About 75 per cent of the latter type adhered when it was applied at 1600°C.TBRC availability increased from an historical average of 62.5 per cent to 64.7 per cent during four campaigns when hot gunning was routinely practiced. Refractory cost was about 20 per cent less than that anticipated without gunning. Average parameters per campaign with gunning ranged as follows: 90 to 108 heats, 10 to 37 applications and 1.4 to 2. 7 hours per application. Prior to gunning, the average number of heats per campaign was 73.IntroductionThe Top Blown Rotary Converter process at Inco's Copper Cliff Nickel Refinery converts copper-nickel-sulphur concentrates to a material suitable for carbonyl refining (1),(2).Operating conditions are particularly hard on refractory. Batch cycles finish at temperatures up to 1650°C, with occasional excursions over 1700°C. New heats are then usually initiated immediately and the refractory is subjected to intense thermal shock from the cold feed. Temperature cycles are also introduced three to four times during a heat when the process is interrupted for scrap charging, temperature measurement or sampling.Abrasion wear results from rotation of the converters at speeds up to 15 RPM and from agitation of the bath with supersonic-velocity oxygen. Mechanical damage also occurs when chunks of scrap or solid matte are processed. Chemical corrosion is also present, as we know from our own laboratory work(2) and reports of operations elsewhere. As a consequence, refractory material and installation form a very large proportion of the converter plant costs. Equally important is the loss of converter availability during rebricking; this significantly reduces plant capacity."

Jan 1, 1981

By X. T. Feng, Y. H. Hatzor, Y. Tal, G. Yagoda-Biran

"When studying jointed rock mass deformation around underground openings it is of great importance to model correctly the excavation sequence during the numerical simulation. This is because for effective arching mechanism to develop in the roof minute block displacements must take place and some of the available discontinuities shear strength must be mobilized. If from the beginning of the simulation the underground opening already exists in the numerical model, block displacements into the excavation space will initiate and develop from time zero, before the initial stresses in the model have attained their actual initial level in the field. These initial block displacements are therefore artificial and exist only in the numerical model, not in the physical reality, and may lead to erroneous assessment of the stability of the designed structure, typically on the conservative side. We have introduced sequence excavation capabilities both in the numerical manifold (NMM) and the discontinuous deformation analysis (DDA) methods and show here the advantages of this modification using three different case studies, each illuminating a different aspect of this enhancement.We begin with the 25 meter deep 2000 year old underground Zedekiah limestone quarry below the old city of Jerusalem, Israel, which is still standing today unsupported with a free span of 40 m. We show that when the opening exists from the beginning of the numerical simulation the required friction angle for roof stability is 25 degrees, whereas when the opening is removed after all stresses and displacements in the model have been stabilized the required friction angle for stability is only 15 degrees.We then model the excavation sequence of a tunnel model representing a 2500 meter deep research tunnel in the Jinping hydroelectric project, China, in order to determine the in situ stress field at this depth by a grid search inversion of displacement data obtained using the sliding micrometer technology in the course of tunnel excavation. Thus we are able to constrain the in situ stress field at these depths where standard in situ stress measurement procedures are extremely difficult to execute properly.Finally, we use sequence excavation modeling capability to find the total height of the expected loosening zone around tunnels excavated through columnar jointed basalts which pose a great engineering challenge because of the characteristic dense network of slender prismatic blocks that transect the opening at a steep inclination. We use MPBX data obtained during excavation of a deep tunnel through such a rock mass to validate our numerical results and show that application of standard empirical guidelines for dimensioning rock bolt reinforcement in such rock masses may in fact result in very un-conservative design because existing empirical approaches typically ignore the anisotropic nature of the structure of such rock masses which, as we show, plays a very significant role in determination of the extent, shape, and geometry of the loosening zone around the opening."

Jan 1, 2015

By A. Scheltema Beduin, H. Oterdoom, A. Haaks, C. Kempe, A. Liedtke

"For the Kazchrome DC Ferrochrome plant, SMS-group specifically designed an electrode column that would minimize downtime. Special features include the possibility for on load electrode jointing, on load slipping, and back-slipping. Electrode consumption is strongly related to furnace load and impedance, and is very low at high loads, which makes the graphite electrode an alternative to consider even in AC applications. The electrode could also be applied in other DC applications, as for example TiO2 slag, the novel Conroast process, or (twin) DC FeNi furnaces, and could possibly be installed during bigger shut downs. This paper will describe some of the design considerations and operational performance data on this novel column in the FeCr industry that could also be of interest for the FeNi or PGM industry if these would continue to develop towards DC technology.INTRODUCTION Every DC furnace has a cathode and an anode. The anode applied is commonly known as the Concast design, though the original design was by ABB who handed it over to Concast, subsidiary of the SMS-group. Some well-known DC furnaces outside the steel industry where the Concast bottom has been installed are listed in Table 1 as well as a few other key design features.Sidewall cooling and some other data have been left out for reasons of space, and being a lesser relevant design feature to this paper. HES stands for Hollow Electrode System, in which feed is charged through an electrode. Table 1 is built up chronologically according to first start-up date. Below comments are given to briefly explain some of the columns in Table 1: •,“Arm” in the “Cathode” column means that the design of the cathode holding and regulating mechanism consists of an electrode arm as depicted in Figure 1. •,Charging is relevant as some operations started with HES charging, whereas recently most new operations have started without HES but only charging chutes, of which at least some are close to the electrode and possibly others installed closer to the sidewall. •,“Dome” in the “Roof” column means that the design of the roof involves a center piece that can be exchanged if worn. •,The optimal roof design still seems to be a topic of debate, where no design is without problems."

Jan 1, 2017

By B. Chareyre, H. Pourpak, L. Scholtès, E. Papachristos

"Numerical methods used to study hydraulic fracturing in low permeability rock masses need to take into account the interaction between the progressive failure mechanism of the intact rock matrix and the pre-existing natural fractures. A fully coupled hydro-mechanical 3D discrete elements model dealing with such interaction is presented here. The ultimate objective is to grasp the role of the rock-matrix failure on the propagation of the main fluid driven fracture under different stress fields and pre-existing fracture orientations. The proposed method provides the spatiotemporal distribution of the induced crack events which can be tracked during the simulations, making possible the identification of the local mechanisms leading to macro-failure in the rock matrix or reactivation of the discontinuity planes. Fluid flow inside a fracture, pressurized crack and hydro-fracking experimental tests were simulated as part of the validation process of the model and, are presented in this paper.INTRODUCTIONWith the expansion of shale gas and geothermal reservoirs exploitation, the technique of Hydraulic Fracturing (HF) has been widely used over the past years (McClure, 2012; Britt, 2012). Despite recent advances in micro-seismicity analysis or numerical modeling (Nagel et al., 2013), the way progressive failure of rocks affects the fluid flow depending on the in situ stress conditions or the rock heterogeneities is not fully controlled yet (Zoback, 2010).In this work we focused on setting up a three-dimensional discrete elements model to study fluid driven fractures propagation. The intact rock is modeled by a discrete element method (DEM) able to reproduce fracture initiation and propagation (Scholtès and Donzé, 2013, Garcia et al., 2013). The pre-existing fractures are explicitly modeled and can be individually defined or be part of a discrete fracture network (DFN) (Harthong et al., 2012). Their mechanical response is fully coupled with the fluid within a HM-DEM framework. The fluid flow and it’s interaction with the intact matrix and the pre-existing discontinuities is modeled through a Pore-scale Finite Volume (PFV) scheme specially enhanced for fractured rock modeling (Chareyre et al., 2012, Catalano et al., 2014) ."

Jan 1, 2015

By H. Kolcz, G. S. Dobby, R. Stratton-Crawley, S. W. Wilson

"The Matte Separation plant at Inco's Copper Cliff Smelter Complex is described. The continuing implementation of flotation column technology in the flowsheet in various applications is reviewed. Comparative studies on 0.038, 0.10, 1.1 and 1.8 m diameter columns have been carried out. It was demonstrated that consistent metallurgical performance was obtained with both pilot- and plant-scale units. Grade-recovery relationships for plant columns can be predicted with confidence from data obtained from test equipment. The work indicates further areas of the flowsheet in which columns present an attractive alternative to conventional cells. INCO’s MATTE SEPARATION PROCESSNickel concentrate from Inco’s Sudbury area mills has been processed in the Copper Cliff smelter for sixty years. Prior to that, Sudbury ores had been smelted directly. Historically, copper-nickel separation from smelter converter matte was achieved by the classical Orford process. In the mid-1940s Inco developed an improved separation scheme based on mineral processing methods, the Matte Separation Process. A generalized Copper Cliff Smelter Complex flowsheet is shown in Figure 1.Iron sulfide and gangue contained in the nickel concentrate are rejected in the smelting-converting process. The molten product, typically containing 50% Ni, 25% CU and 22% s, is cast at about 1000 ºC, into floor moulds and allowed to slowly cool for four days. During this period nickel sulfide (heazlewoodite, Ni,S,), copper sulfide (chalcocite, cu,S) and a copper-nickel metallic alloy precipitate and form a coarse grain structure that is amenable to separation by physical means. The phase chemistry of this system has been described previously by Sproule et al (1). This matte then becomes the feed to the Matte Separation Process.A simplified block flowsheet of the Matte Separation Process is shown in Figure 2. Matte ingots, typically weighing 20 tonnes each, are broken and crushed in a three stage crushing plant to approximately minus 0.01 m and conveyed to the Matte Separation building. Grinding is carried out in two parallel circuits each consisting of a rod and ball mill in series producing a flotation feed which is 65% minus 44 microns. Typical throughput of each grinding circuit is 650 tonnes/day. The metallic fraction of the feed is recovered by magnetic separation. This product, containing about 66% Ni and 15% CU, is a major component of the feed to the Copper Cliff Nickel Refinery."

Jan 1, 1990