Search Documents

By George H. Bodfish

This paper begins with a short history of air compressors, emphasizing their "roots" in the mining industry. It then describes the types of compressors available, including reciprocal, the various rotary positive-displacement compressors, and the centrifugal. The advantages and disadvantages of selecting a certain type of compressor over another are enumerated, considering customer requirements and operating costs, among other factors. Guidelines to operation and maintenance are discussed, including installation, monitoring and maintenance procedures. Finally, the paper addresses itself to future trends, with special attention being given to the system concept, the increasing use of rotary compressors, power consumption, reliability, packaging and noise attenuation.

Jan 1, 1978

By K. R. Barnard, K. D. Marte, T. V. Gamarano

"The first commercial scale application of CSIRO’s direct solvent extraction (DSX) technology has been in operation at the Boleo project in Mexico since December, 2015. In this application, DSX is a synergistic solvent extraction system consisting of the extractants LIX 63 and Versatic 10 for recovery of cobalt and zinc from a solution background of manganese, magnesium, and calcium. Key operating parameters such as metal extraction, phase disengagement and extractant stability are summarized and discussed in this paper.INTRODUCTION Commissioning of the Boleo processing plant, located on Mexico’s Baja peninsula, began with the copper circuit starting in late 2014, with first copper cathode production achieved in January, 2015. The cobalt and zinc circuits began commissioning in December, 2015 with first zinc sulphate monohydrate (ZSM) and cobalt cathode production achieved in February and April, 2016 respectively. The Boleo project flow sheet and development has been described in detail in previous publications (Dreisinger, et al. 2005; Dreisinger, Baxter, & Molnar, 2006; Dreisinger, et al. 2008; Dreisinger, et al. 2009) and is summarized schematically in Figure 1. Boleo is a mixed oxide/sulphide Cu-Co-Zn-Mn high clay deposit that is processed in a whole ore, atmospheric, oxidative and reductive, sulphuric acid/seawater leach. Copper is recovered as cathode by conventional solvent extraction and electrowinning. Cobalt and zinc are recovered, from a solution background of manganese, magnesium, and calcium, by CSIRO’s synergistic solvent extraction technology Direct Solvent Extraction (DSX). Cobalt and zinc are bulk stripped from the DSX circuit and then further purified by phosphinic acid solvent extraction to produce zinc sulphate monohydrate granules via spray dried granulation and cobalt cathode rounds via divided cell electrowinning."

Jan 1, 2017

By David J. T. Carson

"The metalliferous deposits of Vancouver Island have generally been assigned to the Mesozoic ""Coast Range Orogeny."" However, a metallogenic study by the writer has revealed that several important classes are early or middle Tertiary. Included are porphyry coppers, and gold-quartz, arsenic and copper-arsenic veins.The porphyry coppers and many gold-quartz veins are within and adjacent to Oligocene-Eocene quartz diorite intrusive complexes. Arsenic and copper-arsenic veins have a close spatial relationship to sills and laccoliths of Oligocene dacite porphyry which intrude the late Cretaceous Nanaimo Group.Other deposits of demonstrable Tertiary age include a molybdenum stockwork related to a relatively potassic Eocene plug and a few small copper-skarn occurrences. Some copper stockworks and a mercury deposit are probably also Tertiary.The copper deposits of previously recognized Tertiary age are those of the Sooke area that occur in Eocene basalts and Oligocene gabbros."

Jan 1, 1969

By Mohan R. Srivastava

- OUTLINE - apologies and explanations - a quick bit of history - the wisdom of Wikipedia - ?Matheronian geostatistics continued to convert Bre-X?s bogus grades and Busang?s barren rock into a massive phantom gold resource?? - variogram analysis for Busang - would variogram analysis (or variance analysis) have revealed the fraud? - what went right, what went wrong

May 1, 2007

By R. C. Gegg

The property of MacLeod-Cockshutt Gold Mines, Limited, is in the Little Long Lac area of the Thunder Bay Mining Division, Ontario, about four miles south of the Canadian National railway station of Geraldton. The town of Geraldton is about 170 miles east of Port Arthur and 22 miles west of Long Lac, which is on the main line of the Canadian National railway. The Trans-Canada highway passes through the property and during the winter season the road is maintained between Port Arthur and Long Lac. Electric power is supplied by the Hydro-Electric Commission of Ontario from their Cameron Falls plant and is distributed at 44,000 volts by a local transformer station. Early History The South orebody was discovered by diamond drilling in the spring of 1936. This is a porphyry contact orebody with major pyrite and minor arsenopyrite mineralization. Some gold is present in the 'free' state, but for the most part it is locked in the pyrite, with little or none in the arsenopyrite. Preliminary test work was based on comparing straight cyanidation with bulk flotation and cyanidation of the concentrates. The overall results by the two methods were found similar, but for economic reasons the flotation-cyanidation process was adopted. Before the mill came into operation, a new and entirely different type of orebody, consisting of massive sulphide lenses in banded iron formation, was discovered to the north of the existing workings. These bodies are an intricate mixture of pyrite and arsenopyrite, both carying gold.

Jan 1, 1949

By C. Hari Manoj Simha, J. Gholipour, M. J. Worswick

Due to the high pressures involved in the hydroforming process, friction and lubrication play an important role and can affect formability of the material. Tubes of A1Mg3.5Mn aluminum alloy, of 76.2 mm (3 inch) outside diameter and 2-mm thickness were considered in this study. Three kinds of lubricants, Al070, Hydrodraw711 and water, were applied to the tubes and tubes were hydroformed to burst in a square shape die cavity. The key process parameters were recorded during the tests. An in-house Gurson-Tvergaard-Needleman (GTN) damage-based material model, implemented in LS-DYNA, was used to model the process and predict the formability of this material. The applied axial loads and internal pressures recorded during the tests were used in the computations. The effect of different types of elements (solid and shell) with different constitutive models (von Mises and GTN models) in predicting the strain distribution is studied. The GTN damage-based material showed a good ability to capture necking and displacement histories in this process. Both predicted and measured results showed that the lubricant with lower coefficient of friction can effectively increase the comer expansion.

Jan 1, 2006

ABSTRACT Based on mineralogical characteristics and processing techniques required, gold ores can be classified into 12 types: gold placers, quartz vein-lode ores, oxidized ores, silver-rich ores, iron oxide copper-gold ores, porphyry copper-gold ores, iron sulphide ores, arsenic sulphide ores, antimony sulphide ores, bismuth sulphide ores, telluride ores, and carbonaceous sulphide ores. The bulk mineralogy and gold deportment of each ore type differs and may have a significant impact on ore processing and metal extraction. This paper summarizes the bulk mineralogy and gold deportment in some major types of gold ore and discusses the potential impact of gold deportment on gold metallurgy.

Jan 1, 2013

By D. M. Maijer, S. M. Mohseni, A. B. Phillion

The microstructure evolution kinetics of aluminum alloy B206 during artificial aging has been investigated using non-isothermal calorimetry. A combination of differential-scanning calorimetry (DSC) and tensile tests have been utilized to develop an Avrami model to predict the precipitation kinetics as a function of the thermal processing parameters. The Avrami coefficients, found based on a Kissinger analysis, compare well against those reported in the literature for aluminum-copper alloys. The rapid precipitation kinetics predicted by the Avrami model at temperatures higher than 200°C were assessed through a qualitative comparison against hardness measurement results. In contrast to the continuous hardening observed at 150°C, the material softens with continuing heat treatment at 250°C resulting in an overaged state. This can be attributed to the rapid precipitation kinetics at this temperature, leading to the termination of the precipitation-hardening effects at early stages of artificial aging.

Jan 1, 2015

By M. Tardif, F. L. -Lavoie, M. Ruel

"In mineral processing, it is often very difficult to reliably measure several key operation variables. The harsh environment and high temperature encountered in pyrometallurgy processes lead to some difficulties when selecting the instruments, valves and actuators. If an important variable cannot be measured or manipulated adequately, controlling it can really become a big challenge. Sometimes, it is simply impossible to find the perfect equipment for the task. To help overcome these difficulties, a different approach is required. This approach will not correct the inherent problems related to the instruments and valves, but will cope with these problems. This article will demonstrate how modern process control techniques can be used to solve complex problems while remaining easy to implement. In this article we will described how soft sensors and multivariable fuzzy logic control were implemented at Koniambo Nickel to stabilize the furnace feed and allow for safe and reliable operation of an 80 MW DC arc furnace.INTRODUCTION Process Overview The process plant at Koniambo Nickel SAS is located in the North Province of New Caledonia, 310 km north of Noumea. The nickel-bearing ore is mined in the nearby Koniambo massif. After being screened and crushed, the ore is transported to the processing plant using a 12 km conveyor. After stacking in two blending piles, the ore, containing 2.3% nickel, is fed to the processing plant where it will go through the NST process (Nickel Smelting Technology) before being sent to refining and shotting. This article will focus on the improvement to control of the NST processes. The first steps of this process consist of milling the ore and removing all moisture through calcining (Figure 1)."

Jan 1, 2017

By Magdy Ibrahim

This paper presents experimental design and development of a low-cost remote sensing hardware designed to support automated site data acquisition for near real-time progress reporting of construction operations. The developed hardware utilizes open source microcontroller equipped with multiple sensors that include 3D accelerometer, GPS, Data logger and Bluetooth. The use of open source microcontroller makes the developed design cost effective; freeing it from the need for costly license fees. Its platform configuration is flexible; enabling the addition of temperature, weight and other sensors, Wi-Fi and Xbee capabilities to suit individual field applications. Pilot tests have been carried out in laboratory and outdoor environments. The results prove effectiveness and robustness of the developed configuration. The paper provides description of the individual components used in the development of this prototype hardware. It also describes the technical characteristics, capabilities and limitations of the developed hardware. The findings of comparison with alternative technologies used for outdoor tracking of construction operations are presented. The comparison is carried out with respect to range, cost and suitability for outdoor environment. The developed hardware is expected to support a wide range of applications including tracking of earthmoving operations, highway construction and onsite resources. As well, it is expected to enhance safety on construction jobsites.

Aug 1, 2013

By Hrayr Agnerian

The fair market value of an exploration property is determined by its potential to host a mineral deposit. This potential is gauged by the results of previous exploration, exploration stage, meaningful past expenditures and remaining targets that are not yet tested. Values of exploration properties can be viewed as distinct points in a three-dimensional space defined by orthogonal axes, namely: Exploration Stage (x-axis); Cumulative Expenditures (y-axis); and Property Value (z-axis). In general, these values are estimated by applying activity factors on previous exploration expenditures, e.g. an activity factor of 100% for an active property with good potential and a factor of 50% for an active property but past expenditures have not upgraded the property. At certain periods, a market factor may also be applied to reflect the activity of mineral property acquisitions. For properties that do not exhibit any exploration potential, only nominal values are applied.

Jan 1, 1996

By Dale A. Walters

The thermal recovery of bitumen reservoirs by steam assisted gravity drainage (SAGD) is often designed to maximize the operating pressure. In general, the benefits of higher operating pressures are higher steam temperatures that maximize the reduction of oil viscosity, potential permeability enhancement associated with lower effective stress and shear dilation, and a larger pressure window to allow flexible control of the producer. This is especially important for shallow reservoirs where the pressure window for injection and production is smaller. Higher operating pressure can reduce thermal efficiency (due to heat losses), but the other benefits usually compensate. The limitation of the maximum operating pressure is then based on maintaining caprock integrity. Thus, shear and tensile failure mechanisms must be quantified and managed. This paper presents a geomechanical analysis of caprock integrity for SAGD operation. Both analytical and numerical approaches are used to investigate the modes of caprock failure. Main factors in the analysis are the knowledge of the initial stress state and proper representation of the complexity of the geomaterials. Typical initial stress states for northern Alberta are presented showing the potential for low initial minimum total stress and elevated initial shear stress levels. The stress-strain behavior for the sand and caprock materials is discussed focusing on the potential for shear dilation in the sand and shear strength behavior in the caprock. Elasto-plastic constitutive models used to represent the sand and caprock are presented and compared using numerical analysis. The increase in pressure and temperature alter the stress state and disturb the soil matrix. This disturbance results in shear dilation of the sand matrix creating regions of enhanced permeability and porosity. Also, the transfer of stress and strain to the caprock causes dynamic stress changes and, therefore, dynamic behavior of shear and tensile failure conditions. Calculations are presented showing the stress paths associated with SAGD operations, suggesting better design of lab testing programs and the implications for shear dilation in the sand and shear failure in the caprock.

Jun 1, 2012

By V. G. Papangelakis, J. E. Dutrizac, G. Azimi

A new model capable of predicting the solubility of calcium sulphate solid phases in zinc sulphate processing solutions from 25 to 95°C was developed. The model uses the Mixed Solvent Electrolyte (MSE) model of the OLI systems software to calculate the mean activity coefficients of the electrolyte species. The model was tested using recently developed experimental measurements. It was shown to predict accurately the solubility behaviour of calcium sulphate in multi-component zinc processing solutions containing ZnSO4, H2SO4, MgSO4, MnSO4, Fe2(SO4)3, Na2SO4 and (NH4)2SO4. The model can also explain the complex effect of coexisting metal sulphates on the solubility of the CaSO4 phases. The model is a practical tool for assessing the process chemistry of a wide variety of complex aqueous processing streams.

Jan 1, 2008

By B. Drew, K. Budna, C. Wenzl, D. Gregurek, A. Spanring

"The metallurgy of nickel and cobalt and of copper is closely interlinked when processing sulfidic Ni-Co ores and Cu-Co ores. The respective furnaces are typically lined with magnesia-chromite refractories, which are exposed to multiple and complex stresses. The selection of the processing route, furnace type and slag system will be dictated by the specific ore type available, this will determine the individual refractory wear mode. This paper evaluates the common refractory wear mechanisms, namely infiltration, spalling and chemical attack by various slag systems, as well as sulfur attack, as observed when processing primary sulfidic ores. All these wear parameters, which are discussed in this paper, lead to a severe degeneration of the brick microstructure and a decreased lining life. Therefore, a detailed investigation and understanding of the wear mechanisms through “post mortem studies” is an important prerequisite for the refractory producer. Based on such research results, combined with specific process knowledge, appropriate brick lining solutions for nickel and cobalt processing furnaces can be recommended.INTRODUCTION The metallurgical production of cobalt and nickel and of copper is closely interlinked to the mineralogy of the respective ores: cobalt is found in African Cu-Co ores as well as in Co-rich nickel ores (laterites and sulfides). Also, Co-bearing secondary raw materials contain the mentioned elements in different contents. In pyrometallurgical processing of sulfidic ores, cobalt is generally recovered as a by-product during the production of copper and nickel, whereas it is normally not recovered separately during the processing of nickel laterites but remains in the FeNi product. Besides various hydrometallurgical production routes, the pyrometallurgical processes involved comprise smelting (i.e., production of a Cu-Ni-Co-Fe matte in electric or flash furnaces), converting and refining (i.e. removal of Fe and S as well as other elements from matte by oxidation). The ongoing trend to use higher oxygen enrichment in process air enables higher intensity processes but also increases the oxidation potential in the vessel. Therefore, during smelting and especially during the oxidative treatment in converting and refining, some amounts of valuable metals are also transferred to the slag in their oxides form. A subsequent slag treatment is then applied for recovering valuable metals from the slag, namely allowing an economic material stream handling and minimizing metal losses. This is often done in a slag reduction furnace. Additionally, copper and nickel are very good collectors for precious metals and platinum group metals (PGMs) - therefore, depending on the content of these metals, an additional refining process is used to recover these valuable metals from the matte or metal phase (Elvers et al., 1997; Davenport et al., 2002; Crundwell et al., 2011)."

Jan 1, 2017

By L. E. Djingheuzian

ANON-CATARACTING (N-C) ball mill is so operated that the balls are not thrown in-ward at the top of their paths. The result is to maintain, in the mill, a quiescent pool in which classification will occur at a limiting size corresponding to the pulp density. N-C operation is produced by effecting proper relationship among mill speed, ball diameter, volume of ball load, and pulp density. Such operation is typified by the primary ball-mill operation of the Tennessee Copper Company, Copper-hill, Tenn., and the Cleveland Cliff Iron Company, near Ishpeming, Mich.

Jan 1, 1958

By R. S. Adhikari

This paper presents an innovative computer vision method for condition assessments of bridges with multiple defects in bridge elements using digital images. This work utilizes 3D model of existing bridges and overlays digital images on 3D model to simulate on-site visual inspection. The analysis of element condition index (ECI) of bridges requires information about the severity and extent of defects in elements. In general, ECI is evaluated manually during routine bridge inspection considering the severity of dominant defects. The evaluation of ECI with multiple defects needs to be addressed with consideration of dominant defect as well as the interaction among defects. However, Image-based quantification techniques largely depend on geometry of objects (i.e. shapes). Shape vectors of a given object change as they are translated, rotated, and scaled with different magnitudes. This work considers shape preserving algorithms such as, affine and projective transformation for proper image alignment. Semi-automated approach for detection and quantification of concrete distress such as cracks and spalling are considered for the defects analysis. The proposed methodology ensures the consistency in reporting ECI and eliminates the shortcoming of traditional approaches.

Aug 1, 2013

By Zhigao Xu, Ruan Chi, Zhenyue Zhang, Yaoyang Ruan, Zhengyan He

Weathered crust elution-deposited rare earth ore is a specific rare earth resource in China that is rich in middle and heavy rare earths. From surface to bottom, the weathered crust elution-deposit rare earth ores can be divided into humic layer, completely weathered layer, partly weathered layer, and bedrock. The exchangeable rare earth ions mainly exist in the completely weathered layer and partly weathered layer, and the exchangeable aluminum ions mainly exist in the humic layer. A novel solution injection method for use in the in-situ leaching technology of weathered crust elution-deposit rare earth ores was put forward based on the different distributions of RE3+ and Al3+ in the four layers. Avoiding the humic layer, only the completely weathered layer and partly weathered layer were leached by controlling the height of the leaching solution liquid level. In this way aluminum, the primary impurity in the RE leaching solution, can be decreased and the purity of the RE product can be improved. Meanwhile, the choices of available leaching reagents were broadened and the possibility of landslide disasters could be reduced.

Jan 1, 2014

By Lihong

A series of Fe2O3-elimination experiments were conducted on feldspar samples from Tangshan Stone?powder Plant. These experimental methods include scrubbing desliming, flotation,rod milling and high gradient magnetic separation. Some technical factors of feldspar concentration and a new technological flow?sheet of ceramics raw material concentration were put forward.

May 1, 2003

"This paper deals with the reconciliation of open stope performance at Olympic Dam, South Australia, with a focus on stope stability, recovery, and operational aspects of stope reconciliation in relation to the expected or planned stope design. The observed stope performance is inconsistent with the equivalent linear overbreak sloughing criteria for assessing the performance of large open stopes. The aim is to investigate new stope performance criteria using quantitative (overbreak, underbreak, maximum depth of wall failure) and qualitative (stope productivity, observed fragmentation) information that correlates with the observed stope behaviour, providing a process for improving future stope designs.RÉSUMÉ Le présent article traite de la réconciliation de la performance des chambres ouvertes à Olympic Dam, Australie du Sud, en ciblant la stabilité des chambres, la récupération et les aspects opérationnels de la réconciliation des chambres par rapport à la conception attendue ou planifiée des chambres. La performance observée des chambres ne concorde pas avec les critères d’épaisseur équivalente du bris hors profil pour évaluer la performance de grandes chambres ouvertes. L’objectif est d’étudier de nouveaux critères de performance des chambres au moyen de données quantitatives (rupture hors profil, rupture à l’intérieur du profil planifié, profondeur maximale d’effondrement du mur) et qualitatives (productivité de la chambre, fragmentation observée) qui concordent avec le comportement observé des chambres, fournissant ainsi un processus pour améliorer les futures conceptions des chambres."

Jan 1, 2015

By J. R. Foster

Investigations into the effect of a variety of acid digestions on common rock-forming minerals demonstrated a considerable variation in the proportion of the total metal extracted. A similar situation applies to the analysis of a number of common rock types. In addition, grain-size variation has an effect on the amount extracted by certain digestions. This work indicates that considerable care needs to be given to selecting an appropriate acid digestion capable of determining metal held in particular components of a sample. By using partial extraction techniques, the identification of certain patterns of metal distribution, undetectable by normal methods involving total metal analysis, may be achieved.

Jan 1, 1973