Search Documents

By Gurupraveen Ramanathan

Shallow-dipping orebodies (45°–60° dip) present significant challenges for underground longhole stoping, particularly due to limited gravity flow, drill misalignment near the footwall, increased potential for dilution from hanging wall overbreak, and deviation from drill string sagging at shallow angles. These geometrical and operational constraints often lead to unblasted ore wedges and excessive overbreak when standard practices are applied. This study develops a structured, data-driven framework to optimize longhole stoping in such conditions by integrating five key focus areas: (1) mining method selection, (2) stope and drift design, (3) drill and blast optimization, (4) equipment selection, and (5) performance evaluation. The suitability of longitudinal longhole stoping was validated for narrow vein geometries using orebody analytics and prior case studies. Geometric modeling was employed to determine optimal stope height (15–20 m) and stope width (1.5–2.5 m), with drift widths adjusted based on orebody dip to maintain drill access and minimize unbroken ore. Drill and blast design emphasized sequential blasting over multi-ring methods to improve void control, reduce wall damage, and enhance fragmentation. Specific burden and spacing guidelines (e.g., 1.8–2.3 m burden; 2.5–3.0 m spacing) were applied based on stope width and dip angle, and patterns were selected based on geometry—dice-5 for narrow stopes, and 3-hole rows for wider stopes. Drill rigs—including top hammer and ITH models from Sandvik, Epiroc, Boart Longyear and CMAC-Thyssen—were evaluated for compatibility with drift dimensions and alignment accuracy. Equipment was matched based on dip, drift width, and the ability to access the footwall at shallow angles. Sensitivity analysis quantified how changes in geometry, drilling accuracy, and blast design affect ore recovery, dilution, and operating cash flow. Results show that tailored drift and stope geometries, combined with proper blasting and rig selection, can boost ore recovery to over 95% and reduce dilution to below 5% in optimal conditions. This methodology offers a practical and economically optimized solution for shallow-dip mining scenarios.

May 4, 2025

By E. Kordzadeh, M. Reza Bateni, M. Karaminezhaad, A. Moeini

A series of austenitic heat resistant Fe-Ni-Cr-Al alloys with different nickel contents have been investigated at 1100 ° C and 25, 50, 50,100 hours in S/0 bearing atmospheres. Before sulphidation test, the specimens were annealed in argon at 1250 °C for 8 hrs. Weight changes were measured using an automatic thermo gravimetric analyzer and corrosion products were analyzed by scanning electro microscope (SEM), energy dispersive X-ray spectrometry (EDAX), X-ray diffraction and optical microscope. The results showed that sulphidation resistance decreased with increasing nickel content. Internal sulphidation controlled by gaseous transport through cracks and pores and the formation of internal sulphide increased when liquid sulphides formed on the surface.

Jan 1, 2004

By P. E. Weidmark

"CANMET InformationPART 1-Published PapersAsmis, H. W., ""The dynamic response of caverns in discontinuous rock""; Proc 22nd U.S. Symposium on Rock Mechanics, Cambridge, Mass, June 1981, 272-277; 1981.Austin , M.W., Bray, J.W. and Crawford, A.M., ""A comparison of two indirect boundary element formulations incorporating planes of weakness"" ; Technical Note; Int J Rock Mech Min Sci Geomech Abstr; 19:339-344; 1982.Barrett, J. R., ""Applying geotechnical theory to underground metalliferous mining""; Proc 1st Intnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of AIMMPE; 210-222; 1983.Barron, K., Wright, P.L. and Smales, T., ""Guideline s for the design of coal pillars in the No .4 seam at Mclntyre Mines Ltd ., Grande Cache, Alberta""; Proc 1st Intnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of A IMMPE; 559-578; 1983.Bauer, A., ""Wall control blasting in open pit mines""; Mining Engng; 34:155-158; 1982.Bieniawski, Z.T., "" Improved design o f room-and-pillar coal mines for U.S. conditions""; Proc 1st Intnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of AIMMPE; 19-51; 1982.Blackwell, G.H. and Calder, P.N., ""Practical aspects of wall stability at Brenda Mines Ltd., Peachland, BC""; 3rd Intnl Conf on Stability in Surface Mining; Vancouver, BC, June 1981; SME-A1ME; 3:573-608; 1982.Blake, W., ""Microseismic monitoring for underground stability "" ; Proc 1st Intnl Cont on Stability in Underground Mining; Vancouver , BC, August 1982; SME of AIMMPE; 272-294; 1983.Brawner, C.O., ""Stabilization of rock slopes"" ; 3rd Intnl Conf on Stability in Surface Mining; Vancouver, BC, June 1981; SME-AIME; 3:289-310; 1982.Bridges, M.C., ""Review of open stope mining in Australia""; Proc 1st lntnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of AIMMPE; 813-828: 1983."

Jan 1, 1983

By Hilden. M.

"As the Cadia mill was the first 40ft diameter SAG mill, commissioned in 1998, its performance, liner and discharge design attracted considerable international attention. Twelve years on, the liner design and the control philosophy are being readdressed to further improve the mill’s performance. A comprehensive series of 3D liner scans, over life of the liner, have been used to calibrate liner mass loss and progressive changes in the liner profile. This data is being used to provide true charge mass and mill filling, plus progressive trajectory profiles over life of liner. This information, along with measures of mill performance over liner life, is being used to select the optimal operating conditions as the liner wears, and hopes to inform future liner design. INTRODUCTIONSince the Cadia mill was the first 40ft diameter SAG mill, its performance, liner and discharge design has attracted considerable international attention, as reported in previous SAG conferences. The mill experienced particular challenges with regard to pebble and slurry discharge, which necessitated a discharge redesign, incorporating a considerably greater pebble port open area and curved pulp lifters (Hart, Valery, Clements, Reed, Song & Dunne, 2001). Packing between lifter bars on the shell liner was found to dramatically reduce mill throughput over the first half of the liner life. In response, the liners were redesigned to a 2/3 spacing so as to open up the space between lifters. Due to ongoing high liner wear issues, the liner was redesigned based on the discrete element modelling (DEM) of Conveyor Dynamics conducted by Nordell and Potapov (2001). This aimed to maintain mill throughput with new liners and provide an extended liner life. This design was kept proprietary for many years, so has not been open to review."

Jan 1, 2012

By B. A. Sparkes, J. H. Reeves

"The St. Lawrence Granite hosts vein-type fluorite mineralization that was mined until 1977. Recent drilling identified a significant fluorite-bearing structure hosted in adjacent meta-sedimentary country rocks. Several phases of vein fill and brecciation indicate there are three phases of fluorite mineralization, of which the later two phases are volumetrically significant. The earliest fluorite is purple and occurs along joint and fracture surfaces, in fault-breccia matrices, and as stockwork veins. The second phase comprises primarily red, yellow, blue-green, and white colours of fluorite. The latest phase is green with lesser clear fluorite. Identification of fluorite veins in the meta-sedimentary rocks opens up new areas for exploration.RÉSUMÉ Le granite St. Lawrence contient une minéralisation filonienne de fluorite, laquelle a été exploitée jusqu’en 1977. De récents forages ont permis d’identifier une structure importante contenant de la fluorite encaissée dans des roches métasédimentaires adjacentes. Les nombreuses phases de remplissage de filons et de formation de brèches indiquent qu’il y a eu trois phases de minéralisation de fluorite et les deux dernières sont importantes d’un point de vue volumétrique. La plus ancienne fluorite est mauve et se trouve le long de surfaces de joints et de fractures, dans les matrices de brèches de failles et en tant que stockwerks filoniens. La deuxième phase comprend surtout des fluorites de couleurs rouge, jaune, bleu-vert et blanc. La fluorite de la plus récente phase est verte avec des quantités moindres de fluorite claire. L’identification des filons de fluorite dans les roches métasédimentaires ouvre de nouveaux secteurs pour l’exploration."

Jan 1, 2016

By Alan Rice

Abstract-The mechanism by which stratiform ore deposits of PGE (platinum-group elements) are laid down in ultramafic igneous complexes is not completely clear. Early studies by the author and coworkers on numerical analyses of the convective cooling of low-Rayleigh-number magma chambers examined the effect of suspended crystal load on fluid density, and raised the possibility that the growth of the suspended crystal load during cooling could split a magma chamber into several convecting layers. The lower layers would have a higher content of refractory phases than the upper layers, which would consist of more evolved melt. This paper considers numerical modelling, as well as theoretical and experimental work in other fields dealing with suspended loads in fluids. The calculations, which are based on the physics of convecting magmas, yield quantitative relationships consistent with the observation that economically interesting stratiform PGE deposits are restricted to large magma bodies, and also yield estimation of the depth in a magma chamber at which certain grades of mineralization may occur.

Jan 1, 1997

By Alan Rice

The mechanism by which stratiform ore deposits of PGE (platinum-group elements) are laid down in ultrama?c igneous complexes is not completely clear. Early studies by the author and coworkers on numerical analyses of the convective cooling of low-Rayleigh-number magma chambers examined the effect of suspended crystal load on ?uid density, and raised the possibility that the growth of the suspended crystal load during cooling could split a magma chamber into several convecting layers. The lower layers would have a higher content of refractory phases than the upper layers, which would consist of more evolved melt. This paper considers numerical modelling, as well as theoretical and experimental work in other ?elds dealing with suspended loads in ?uids. The calculations, which are based on the physics of convecting magmas, yield quantitative relationships consistent with the observation that economically interesting stratiform PGE deposits are restricted to large magma bodies, and also yield estimation of the depth in a magma chamber at which certain grades of mineralization may occur.

Jan 1, 1997

By Mari Yamamoto

Controlled thermolysis of gold(I) complex, [Au(C13H27COO)(PPh3)], at 180 °C for 5 h under an N2 atmosphere affords the new type of monodispersed spherical gold nanoparticles capped by myristate and a small amount of PPh3 ligands (average diameter 23±1.5 nm), in spite of no use of solvent, reducing agent and stabilizer. Much attention has been paid to the preparation and structure determination of transition metal nanoparticles, because of their widespread use in technological applications.1 In general, the chemical reduction of metal salts and organometallic complexes2 by the use of reducing agent is carried out to prepare gold nanoparticles. In some cases, a large amount of solvent and stabilizers such as surfactants,3 polymers4 and ligands5 are used to prevent agglomeration of particles and control the particle size. For instance, Brust et al. reported a two-phase reduction of AuCl4 - by NaBH4 in the presence of dodecanethiol as stabilizer to prepare gold nanoparticles.6 On the other hand, O?Brien et al. recently reported an one-phase preparation of gold nanoparticles by the reduction of AuCl4 - by NaBH4 in the mixture of tri-n-octylphosphine oxide and octadecylamine which act as both solvent and stabilizer, but this procedure also needs reducing agent.7

Oct 1, 2003

By E. Czech

Hydrogen generated through aluminum-assisted water split reaction is a novel, efficient and environmentally friendly method. It has been found previously that the passivation of aluminum can be prevented in neutral (pH=7) or near neutral pH conditions in water by grinding aluminum with a catalyst, such as A12O3, SiO2 or SiC. Recently, the best results have been obtained by using water-soluble inorganic salts (WIS), ground with aluminum. The massive, rapid corrosion reaction of the Al-WIS system which takes place in regular tap (or marine, or ground) water can be utilized to produce hydrogen by aluminum-assisted water split reaction, in-situ, on-demand. The reaction offers clean, low-cost, environmentally benign and entirely recyclable technology for on-board on-demand hydrogen generation. Besides pure gaseous hydrogen, only pure solid aluminum hydroxides AlOOH or Al(OH)3 are formed as the reaction products. The hydrogen yield and Al-WIS reaction efficiency are high. From 1 g of mechanically alloyed aluminum powder, up to 1.25 liters of hydrogen were generated, i.e. efficiency up to 92% was achieved. The amount of hydrogen and hydrogen generation rate depend on various reaction parameters. The effect of chemistry and concentration of additives, water temperature, powder particle size and milling conditions on the reaction kinetics will be presented and the possible process mechanism will be discussed.

Jan 1, 2005

By J. Schmidt

The development of set of laboratory experiments, intended to help undergraduate students meet Canadian Engineering Accreditation Board requirements for Engineering Design outcomes, is described.The laboratory, which is part of a third year level course in hydrometallurgy, is aimed at advancing the ability of students to generate and use experimental results to design an industrial copper leach/SX/EW plant. Emphasis is placed on the students demonstrating the ability to use of their engineering knowledge in weighing the pros and cons of the various process options that they test in converging to a final flowsheet. INTRODUCTION Over the past number of years the Canadian Engineering Accreditation Board, CEAB, has dramatically shifted the way that they evaluate undergraduate programs. In the past, the focus was on measuring of the quantity and quality of material the students were intended to learn as well as the methods and resources used to deliver that material. Now, rather than principally evaluating the inputs of programs, the focus is more on measuring the quality of the outputs from the programs, i.e. the quality of graduating students. In this regard, the CEAB has developed a list of twelve attributes that learners must develop in the course of their studies. Engineering programs must, not only demonstrate that their curriculums provide opportunities to develop these attributes, but must measure student proficiency in each of these attributes as they progress toward graduation. One particular graduate attribute that Laurentian University’s Bharti School of Engineering has encouraged its faculty members to develop content for is “design”. Engineering Canada (2018) defines this attribute as “an ability to design solutions for complex, open-ended engineering problems and to design systems, components or processes that meet specified needs with appropriate attention to health and safety risks, applicable standards, and economic, environmental, cultural and societal considerations”. The previous laboratory component for the hydrometallurgy course was a collection of unconnected experiments covering leaching, solvent extraction, ion exchange, and electrowinning. Like in other undergraduate courses, students would perform stand-alone experiments, make the specified measurements, do the specified analyses of the results, and report the findings, all as strictly detailed in the lab manual. The vision for the new lab was to create an experience that would more closely mimic an industrial research program whereby students would start with a given feed material and would progress through a series of connected experiments. Emphasis is placed on the student demonstrating competency in, not only, generating and analyzing experimental data, but also in using the data along with their engineering knowledge to design and evaluate the pros and cons various plant configuration options. Principally, students are asked to weigh cost, safety, and environmental concerns in converging to their final flowsheet. In designed the leach circuit, students must weigh the costs/benefits of varying leach temperature. Higher leach temperatures will yield faster and more complete copper dissolution, which will allow for the specification of relatively smaller leaching circuits, saving capital costs. However, hotter acid solutions are more dangerous to handle and require increasing amounts of energy to heat the slurry, increasing operating costs. In solid/liquid separation, students must weigh the pros and cons of the addition of a flocculent to assist settling. The flocculant will allow for the design of a thickener circuit that employs units with a relatively smaller area, but will result in a thickener underflow with a lower pulp density, which may necessitate a larger number of thickeners. In addition, the environmental concerns of producing a tailings product that contains an organic contaminant should be addressed. In solvent extraction, students must specify the number of stages of loading and stripping, as well as organic and aqueous flowrates to produce suitable raffinate and rich electrolyte streams. Finally, in electrowinning, students will compare the costs/benefits and risks of the use of precious metal coated titanium dimensionally stable anodes (DSAs) versus conventional Pb based anodes.

Jan 1, 2019

By F. Mercier-Langevin

ABSTRACT; Agnico-Eagle’s LaRonde mine is one of the deepest mines in Canada. Ground conditions in the deeper levels can be very challenging, ranging from hard and brittle to soft and squeezing. As a result, rock mechanics and ground control practices have had to evolve considerably to accommodate progressively deeper mining activities. This paper focuses on the deeper levels of mines and how the difficult ground conditions encountered there have influenced the mining strategy. The first section examines ground control practices and support systems in highly stressed, poor quality rock. The evolution of level layout is also presented. Finally, improvements in stope sequencing are reviewed.

Jan 1, 2010

By Antonio Segatori, Bjørn Holmedal, Kai Zhang, Trond Aukrust, Knut Marthinsen

"The visual appearance and mechanical properties of aluminium alloy extrusions are strongly dependent on the microstructure and texture of the extruded profiles, where the desired microstructure and texture may depend on the specific applications. In the present work, the evolution of deformation, as well as recrystallization textures during extrusion of AA6xxx aluminium alloys, have been experimentally and numerically investigated. Extrusion trials were performed in a laboratory extrusion set-up, which enabled immediate water-quenching of the profiles at the exit of the die, and thus the possibility to capture the deformation texture prior to post-extrusion recrystallization. The textures and their through-thickness variations were experimentally measured by the electron back-scatter diffraction technique (EBSD, and the deformation textures numerically modelled by coupling FEM flow simulations and crystal plasticity (CP) simulations. Different CP models as well as different choices of model parameters were employed and evaluated for texture predictions. With an appropriate choice of crystal plasticity model and model parameters, the deformation texture can mainly be predicted, although the accurate intensities are hard to reproduce. The corresponding recrystallization textures, either generated through spontaneous recrystallization of the extruded profiles or through post-extrusion annealing, are far more challenging to reproduce with available recrystallization models.INTRODUCTION Extrusion is a widely applied thermal-mechanical process to produce aluminium profiles. The properties of the profiles, for example mechanical, fatigue, fracture, corrosion as well surface appearance, are strongly dependent on the underlying microstructure and texture, and the requirements with respect to these aspects may vary with applications (Ralston et al., 2010; Dumoulin et al., 2012; Donati et al., 2013). Moreover, it is often a challenge to produce extrusions with a consistent and homogenous grain structure and texture along as well as through the cross section of the profiles. It is thus vital to understand and be able to predict (model) how different microstructures and textures are formed and how they evolve during and after extrusion, as basis for controlling the final appearance and properties of extruded profiles."

Jan 1, 2018

By K. Woo

"With ever-increasing global demand for mineral resources, mining companies are considering developing deeper, more complex and lower grade ore bodies. Recent years have seen the transition from surface to underground mass mining operations to access deeper resources, with mass mining methods such as block and panel caving being favoured due to the tonnages and economics achievable when dealing with lower grade ore. However, the rock engineering interactions involved with such plans are complex and challenging given the significant disturbance caused to the surface environment. If not properly accounted for, the unexpected propagation of a cave breaking through to surface or the differential surface displacements otherwise produced may threaten the safety and integrity of overlying mine and civil infrastructure.This paper reports the findings of a comprehensive research programme focussed on investigating and integrating new developments in remote sensing characterization and monitoring technologies with state-of-the-art numerical modelling to better manage the challenges and geo-risk associated with the transitioning from open pit to underground mass mining. Procedures were developed to integrate discrete fracture networks (DFN) into finite-element/discrete-element analyses to simulate the influence of rock mass fabric on cave propagation and the evolution of caving-induced surface subsidence and step-path failure of large open pit slopes through the progressive failure of rock bridges. The results clearly showed that caving-induced surface deformations tend to be discontinuous and asymmetric due to large movements around the cave controlled by geologic structures, rock mass heterogeneity and topographic effects. Although parallel investigations of empirical design charts used to predict caving-induced deformations were found to be moderately sufficient for assessing the extent of macro deformations directly above the undercut (i.e. caving collapse features), numerical modelling was found to provide the only means to confidently estimate the lateral extent of smaller strain subsidence.These results were further supported by the use of high-resolution synthetic aperture radar (SAR) data to monitor the ground deformations associated with block caving production, and to use these to calibrate and constrain a series of predictive 3-D numerical models focussed on Rio Tinto's Palabora mine in South Africa. The InSAR data was obtained from Canada’s recently launched RADARSAT-2. The close fit achieved between the predictive 3-D numerical model and InSAR monitoring data demonstrates the significant value of InSAR calibrated 3-D numerical models applied to subsidence prediction.Collectively, the results from this research programme have helped to further the characterization, assessment and understanding of mass mining-induced subsidence, and its evolution, by addressing existing limitations in the use of empirical and numerical design methods. The limitations and uncertainty arising from mine site data were detailed, specifically the representation of mine geology, rock mass properties, in-situ stresses and cave propagation, together with means to constrain these inputs and calibrate sophisticated 3-D numerical models through back analysis and integration with high resolution monitoring data."

Jan 1, 2015

By L. M. Pidgeon

Abstract The production of metallic calcium, by reduction of lime with aluminium, was investigated. Using a modified form of the effusion method, the vapour pressure of calcium above the reaction: 4CaO + 2Al ~ 3Ca + CaO.AI203 was determined and found to vary from 1.0 to 1.3 mm. Hg from 1,150° to l,200°C. From the magnitudes of the various thermodynamic quantities involved, together with a consideration of the known chemical characteristics of the reaction, it was suggested that the reaction proceeded by reduction of lime with aluminium vapour. INTRODUCTION The conventional production of metals by reduction of their ores by carbon (or carbon monoxide) may be represented by the equilibrium: MO+ R [] RO+ M . . . . . . . . . .(1) where MO represents the metal oxide, and R the reducing agent (carbon or carbon monoxide). The free energy change ?F° associated with the reaction is given by -?F° = RTlnKp . . . . . . . . ... . (2) where R is the gas constant, T the absolute temperature, and KP the equilibrium constant. It should be noted that ?F° represents ? the standard free energy gained by the system and hence -?F° is the free energy gained by the surroundings - and that as ?F° increases K must decrease, and conversely. For metals above manganese in the electromotive series, the ?F° associated with reaction would quantity and from it can be seen that this corresponds to a small fraction for K. The equilibrium pressure of the oxide of carbon represented by RO is then too near its concentration in the furnace gases for the reaction to proceed in an internally fired furnace. For the practical reduction of such metals, fuel fired furnaces are inadequate. Electric furnaces may be used to give higher temperatures with lower concentration of carbon oxides and the reaction may still proceed. However, for many metals such as calcium and aluminium the formation of stable carbides or acetylides may prevent production of the metal by this reaction. In this case, either electrolytic methods must be used, orrecourse must be had to reducing agents other than carbon. It is the latter method which is under consideration here.

Jan 1, 1948

By M. Behrouz

Thermal power plants convert thermal energy due to nuclear reactions or the combustion of coal, gas, heavy oil, or some other hydrocarbon to electrical energy. They consist of a variety of equipment, such as boilers, turbines, generators, cooling towers, and auxiliary equipment. Any factor that affects the equipment efficiency affects the overall efficiency. Analysis of the cooling tower and raw water using the Langlier Saturation and Ryznar Stability Indices showed that the cooling water at Sarchesmeh was slightly scaling with respect to silica. Cold lime softening was found to be a cost-effective method to produce cooling water with adequate properties to reduce the cooling water make up from 85 to 70 m3/h and blow down rate from 35 to 20 m3/h.

Jan 1, 2007

By Jian Li, Robbie McDonald, David Robinson

"The pressure oxidation of sulfide minerals at temperatures above 200°C enables the extraction of base metals, improves the extractability of gold from refractory ores, enables solubilisation of PGEs and can be used to hydrothermally upgrade base metal-containing feeds. Fundamental studies reveal that the solution chemistry (and mineralogy of the solids) during pressure oxidation can be manipulated with outcomes that include (1) increased leaching rates, (2) lower oxygen requirements and (3) the formation of chemically more stable residues. This paper presents examples describing how these outcomes might be achieved based upon fundamental investigations.INTRODUCTION The application of pressure oxidation to the processing of gold ores and concentrates dates back several decades and continues to be the process of choice at operations such as Pueblo Viejo (pyritic gold) which host the largest autoclave of its kind in the world (Barrick Gold Corporation, 2016). Commercial application to the processing of base metals and PGMs resides with long established processes such as the Sherritt process, ore specific applications such as by Noril’sk, at Sepon etc. or has not proceeded to date beyond pilot scale testing (e.g. Phelps Dodge, CESL, Activox, Platsol). Recently there has been significant interest in hydrothermal upgrading options for concentrates including the NONOX and Toowong processes (Rohner et al., 2016; Weidenbach et al., 2016). The latter options suggest directions where sound knowledge of the underlying fundamentals enables novel outcomes and efficiencies to be obtained. It comes as no surprise that investigations similar to those underpinning these developing processes can be traced back several decades. It is not the subject of this paper to provide a historical perspective of the relevant autoclave chemistries but rather, to present some potential opportunities suggested by studies in our laboratories. Topics to be discussed in this paper include (1) control of metal extraction rates, (2) control of iron-residue composition and (3) control of sulfur oxidation and hence acid generation and oxygen requirements. The work described will focus upon the pressure oxidation of a nickel concentrate."

Jan 1, 2017

By J. M. Beeckmans, S. G. Butcher, M. Goransson

"The counter-current fluidized cascade is a novel and potentially efficient pneumatic gravity separation device. Data are presented on over 150 runs of cleaning Alberta thermal coals, covering several size ranges. The coarser sizes of coal were processed in admixture with a fluidizing medium consisting of 0.5-by 0.1-mm hematite (or magnetite) and limestone particles. The partition curves for coal particles larger than about 3 mm, mixed with fluidizing medium, showed that the sharpness of separation achievable with the cascade approaches that of wet heavy medium processes, whereas with particles in the size range of 3 by 0.6 mm the sharpness of separation was comparable to that of a Baum jig. Useful cleaning was also achieved with particles smaller than 0.6 mm , Throughput rates of up to 11 tonnes per metre width of cascade per hour were achieved, with no indication of a deterioration in performance.IntroductionPneumatic coal beneficiation has steadily lost ground vis-a-vis hydraulic beneficiation during the past quarter century, primarily because of the sharper separations achievable with the latter methods. Nevertheless, there are certain inherent advantages of pneumatic separation methods which would give them an advantage in the market place were it possible to increase their efficiency to be technically competitive with those of hydraulic processes. These advantages are a dry product, resulting in a higher calorific value per ton, and avoidance of the problems associated with treatment and storage of process waste waters. Also, although it may be necessary to dry the raw coal prior to pneumatic processing, the dry rejects produced constitute an ideal fuel for a fluidized-bed combustor, which could provide heat both for drying the coal and for other purposes."

Jan 1, 1982

By P. C. Santos-Munguía, F. Nava-Alonso, O. Alonso-González

"The gold recovery of a Mexican cyanidation plant, in Sonora, has been decreasing due to the increasing presence of gold tellurides. This work presents the results of different processes aimed to recover the remaining gold from the cyanidation tailings of the operation. The cyanidation in the mine is performed at 0.1 g/L NaCN and pH = 10.3, adjusted with lime. The treatments studied in the laboratory with these tailings were: cyanidation at higher cyanide concentration than that used in the plant, cyanidation with oxygen injection, cyanidation with oxygen and lead nitrate addition, and thiourea leaching. The results obtained with each of these treatments are presented and discussed with the final objective of proposing a method to recover the gold associated with tellurium.INTRODUCTION It has been demonstrated that gold telluride is refractory to the conventional cyanidation process and, for this reason, some alternative methods to recover precious metals from tellurides have been proposed. (Zhang et al., 2010). These include cyanidation with modified conditions or the use of non-cyanide leaching agents. This work presents the gold leaching results of tests performed with a sample of cyanidation tailings obtained from a Mexican deposit containing telluride species. The mine exploits a mesothermal deposit with a molar Te/Au ratio of 1, containing also lead, molybdenum, bismuth and tungsten. Gold is recovered from the ore by standard cyanidation, however, lately the gold recovery has decreased, likely due to the tellurium content of the ore. The sample used in this work was the cyanidation tailings of this deposit. It was treated in the plant by cyanide heap leaching (0.1 g/L NaCN, pH = 10.3 adjusted with lime). Some gold remained after the cyanidation and it was thought that this gold was associated with tellurium. The objective of this work was the recovery of the remaining gold from the tailings by an alternative process."

Jan 1, 2017

By Norman M. P. Low

"IntroductionIndustrial applications of mica utilize two commercially important varieties of mica: muscovite and phlogopite. Muscovite mica is a potassium mica with a general chemical formula, H2KA1(Si04)3 h, and is sometimes referred to as a potas hsilicate. Phlogopite is a magnesium mica having a general chemical formula, H2KMgSi(Si04)3, and is distinguished from the muscovite mica by its decomposition in sulphuric acid.Canada is one of the major natural mica producers in the world. A large tonnage of the mica powders is at present mined and processed in the Eastern Townships of Quebec. This Canadian mica is of the phlogopite type. A closely related mineral of the mica family which is widely used in the construction industry is vermiculite. It is a dehydrated magnesium-aluminum-iron silicate characterized by a foliated structure. Expanded vermiculite, which is often referred to as exfoliated mica, is used as many types of thermal and acoustic insulation, as loose fill in buildings, as an aggregate in concrete, as an ingredient in plaster and insulating concrete , and in fire-proofing compositions. Natural phlogopite and muscovite mica powders are used extensively as reinforcing agents in organic polymers. They also have a wide range of applications in commerical products. For example, dry-ground mica powders are used in large tonnage as a surface finish in roofing materials and as a bonding agent in wallboard joint cement. Common products such as paint, rubber, plastics and welding rods contain mica. Recent studies have also shown that mica powders can be added to portland cement in the preparation of concrete products, as they could improve the tensile strength of the concrete products. The potential and possible"

Jan 1, 1982

By B. Krysa, A. Mitsui, T. L. Koehler

The presence of arsenic, even at trace levels, in copper processing leads to the risk of arsine gas where reducing conditions exist that can reduce any soluble arsenic present to its minus 3 valance state and generate hydrogen gas from the solutions. This risk is understood to be significant within the industry, particularly in the case of liberator cells where copper concentrations in solution are drawn down to remove the copper and impurities from the bleed stream. However, there are numerous other potential areas where the arsine gas risk exists including contact between active metal such as iron, zinc or aluminum and arsenic bearing solutions in pyrometallurgical dust treatment, refining and acid plant operations. In turn this breaks down to different mitigating strategies dependent on the risk scenarios considered; for example, how this risk interacts with Change Management, Confined Space Entry or Contractor Training. The ISO 45001 is an emerging standard meant to improve employee safety, reduce workplace risks and create safer working conditions all over the world. The paper shows a case study of how a framework consistent with the tenets of ISO 45001 has been used to provide a consistent assessment of this risk for a wide variety of copper operations and the expectations of how this may be used to effectively improve the effectiveness of barriers against future incidents. INTRODUCTION Arsine gas (AsH3), first identified in 1775, is a highly poisonous, colorless, non-irritating gas with a mild garlic odor that is heavier than air. Arsine gas is generated when reducing conditions are generated in the presence of hydrogen ions and arsenic compounds. Present permissible occupational exposure limit as defined by Occupational Safety and Health Administration (OSHA) as an 8-hour time-weighted average is ppm (0.2 mg/m3). Further increasing the risk, conventional respiratory protection utilizing half or full masks with gas filtering cartridges provide minimal protection against arsine. In copper processing plants, the risk of arsine generation is well understood in liberator cells, which are part of the electrolysis process. In this process, solutions containing copper are reduced in copper concentration removing not only the copper, but also arsenic, antimony and bismuth. The residual solution can be bled to control impurity build-up in the refinery. In this process, if the copper concentration is reduced to the point where As3- can form, arsine gas is generated via reaction with hydrogen ions generated during the plating process. The copper concentration at which arsine gas is generated depends on copper concentration at the cathode surface, the temperature and the acidity. As a result, there is always a risk of arsine gas generation in the liberator cell. Process measures to minimize or mitigate arsine evolution are tight control on final copper concentration, warm temperatures, fresh feed distribution and internal acid recirculation rates. Operator exposure protection measures are hooding, ventilation, arsine detection systems, restricted personnel access, automated shutdown controls and pre-defined evacuation plans.

Jan 1, 2019