Search Documents

By H. Itou

A mechanism of scorodite formation at ambient pressure was investigated using transmission electron microscopy (TEM). Several types of iron arsenate were obtained from Fe/As solutions (Fe/As = 1.0 and 1.5) at pH values of 1.0, 1.25 and 1.5 at 95°C. Amorphous FeAsO4.xH2O was precipitated from solutions having a higher mole ratio of Fe/As at pH l.5, even after 9 hours. A few micron sized particles were observed by SEM, but these proved to be agglomerates of 10-50 nm amorphous FeAsarxH2O particles when observed by TEM. This means that supersaturation of the solution causes the acceleration of nucleation of iron arsenate hydrate. Crystalline scorodite was obtained from a solution in which the Fe/As mole ratio was unity, at pH l.0 and pH 1.5, after 3 hours. Almond-type crystalline scorodite particles were observed by TEM and most of them showed high crystallinity. The addition of scorodite seed material enhanced the crystallization. Amorphous FeAsO4.xH2O, however, was observed at the surface of the seeds during the early stages of precipitation. It is postulated that crystalline scorodite is not directly precipitated even on crystalline scorodite seeds, but requires a certain time to crystallize on the seed material.

Jan 1, 2006

By G. Hausen, H. Micka

"Modern signal and power electronics made adjustable-speed AC drives technically feasible and reliable and economically attractive. Cycloconverters are discussed as a proven technology for mine hoists. \IntroductionUntil rather recent technical and commercial advances in power and signal electronics, DC motors were used almost exclusively for applications requiring continuously adjustable operating speeds and torques. More recently, the significantly higher efficiency and the accordingly lower operating costs of AC motors gained importance. An effective and efficient speed control of AC motors requires the control of AC voltage and frequency. Table 1 shows typical applications of adjustable-speed AC drives.CycloconvertersOf particular interest to the mining industry are cycloconverters for hoist drives. The cycloconverter represents by far the simplest, most efficient and most economical means of converting a constant-voltage, constant-frequency supply into an adjustable-voltage, adjustable-frequency supply as required for the speed control of AC drives operating in the frequency range to half of the utility frequency.Cycloconverters feeding synchronous motors or induction motors are ideally suited for slow-speed direct-coupled drives."

Jan 1, 1988

By K. G. Thorne, M. J. McLeod, D. Hoy

"Throughout the Paleozoic, a variety of gold depositional environments were created in the New Brunswick segment of the northern Appalachians because of the complexity of arc and continental plate collisions and subsequent erosion of the orogen. In southwestern New Brunswick, recent exploration and research has focused on deposits and occurrences that can be broadly classified as intrusion-related, generated by late- to post-orogenic felsic to intermediate plutonic rocks emplaced during the Early to Middle Devonian. This work has led to the establishment of models for gold mineralization and guidelines for exploration in this area, which might also be applicable elsewhere in the southern part of the province and, perhaps, throughout the northern Appalachians. The deposits in the vicinity of Clarence Stream in southwestern New Brunswick exemplify this deposit type, and highlight the emergence of a possible major gold district in the region. Durant le Paléozoïque, une grande variété d’environnements aurifères ont été créés dans le segment néo-brunswickois des Appalaches du nord en raison de la complexité des collisions entre arcs et plaques continentales ainsi que durant l’érosion subséquente de l’orogène. Dans le sud-ouest du Nouveau Brunswick, les travaux d’exploration et de recherche récents se sont tournés vers les gisements et les indices appartenant à la classe des gîtes associés aux intrusions, générés par des roches plutoniques felsiques à intermédiaires tardi- à post-orogéniques mises en place au Dévonien précoce à moyen. Ces travaux ont permis d’établir des modèles de mise en place pour la minéralisation aurifère ainsi que des guides d’exploration pour ce secteur, lesquels pourraient aussi être appliqués ailleurs dans le sud de la province et, possiblement, dans l’ensemble des Appalaches du nord. Les gîtes aux environs de Clarence Stream dans le sud-ouest du Nouveau Brunswick sont un exemple de ce type de gisement, mettant en valeur ce qui pourrait devenir un district aurifère majeur dans la région."

Jan 1, 2008

By E. Zucker

In this paper, as in the 1960 CIM paper of the same name, s1gmf1cant new developments in electrical-mechanical mining equipment are briefly described. These include static thyristor-supplied D.C. drives for mine hoists, load-haul-dump systems, process controls with small and medium-size computers, and several other new items of equipment and Concepts. All the new hardware descriptions are given in the context of over-all process integration. This means the actual mechanical linking together of two or more processes and the preliminary step in the development of production-line mining.

Jan 1, 1969

By David G. Dixon, Ahmad Ghahremaninezhad, Edouard Asselin

"Atmospheric leaching of chalcopyrite in sulfuric acid solutions is a slow process due to the mineral’s passivation. We have investigated the nature of the passive film in this work. Electrochemical reduction and oxidation of chalcopyrite over the potential range of -0.5 to 1.2 VSHE were investigated in 0.5 M sulfuric acid solution (pH 0.3) at 25 ºC by multicyclic voltammetry and open circuit potential measurement. The influence of scan limits on the evolution of current peaks was studied with both stationary and rotating electrodes. It was observed that the anodic oxidation of chalcopyrite begins at potentials above 0.6 VSHE, most likely by preferential dissolution of iron atoms over copper atoms. The selective electro-dissolution process results in formation of a metal-deficient sulfide passive film (i.e. Cu1- xFe1-yS2, y > x). The passive film dissolves at 0.9 VSHE. Elemental sulfur is one of the products of chalcopyrite dissolution above 1.0 VSHE. Cathodic reactions within the potential region of 0.1 to 0.6 VSHE and anodic reactions at potentials lower that 0.5 VSHE are associated with at least one soluble species from solution. The soluble species involved in the cathodic reactions are likely ferric and cupric, while the soluble species involved in the anodic reactions is likely H2Saq."

Jan 1, 2014

By Robert B. Parsons

"First down and four to go. In the game Of football, this is not a bad position to be in. However, in this game of political football, it means that there is still a long way to go. The government in Ottawa has concluded an important agreement with one producing province, and now has at least four more provinces to deal with-B. c., Saskatchewan, Nova Scotia and Newfoundland.On September 1, 1981, the federal and Alberta governments took a significant step forward in formulating an oil and gas policy for Alberta and the rest of Canada on signing a comprehensive five-year agreement that covers taxes, prices, incentives and other fiscal matters related to the production and marketing of oil and gas.This month, Tax Notes examines the main features of the agreement, and offers some eye-opening observations of what the new accord could mean for the future of the Canadian petroleum sector in particular and Canadian business in general."

Jan 1, 1981

By M. R. Campbell

"IntroductionON THE LAST DAY of December, 1951, a half-century of steel production was completed in the open hearth department of Dominion Iron & Steel, Limited, in Sydney, Nova Scotia.During that period, almost every known variation of basic steel making practice was used in working out a steel making process which would overcome the difficult metallurgical problems imposed by the use of Cape Breton coal and Wabana ore.This paper is presented as a brief review of these steel making practices, setting forth the fundamental metallurgical factors involved in their success or failure.Establishing the IndustryThe story of steel production at Sydney is closely interwoven with that of coal. The steel industry owes its inception to a desire on the part of the Dominion Coal Company, which was incorporated in 1893, to improve its marketing position by increasing sales of slack coal and providing a year-round demand for its product. Accordingly, the Dominion Iron and Steel Company, Limited, was incorporated on March 30th, 1899, with Mr. H. M. Whitney -who was President of the Dominion Coal Company -as its first President. The new Company was given powers to manufacture and process iron and steel, and to mine all minerals, including coal.A strong inducement to the industry was the bounty offered by the Dominion Government for the production of both iron and steel."

Jan 1, 1952

By J. E. Udd

"In early 2000, CANMET-MMSL was engaged by the Ontario Ministry of Labour (OMOL) to conduct an international study of the practices, in several key mining jurisdictions, of determining the criteria that are used to decide when the wire ropes used in mine hoisting are to be retired from service. Subsequently, the author visited key officials and institutions in Canada, the United States, the Republic of South Africa, the United Kingdom, Germany, and Poland. Material from the Australian province of New South Wales and Hungary was also included.The report that resulted included, among other sections: (1) the history of wire ropes and trends in manufacturing technology; (2) a review of mine hoisting practices; (3) the requirements regarding safety factors; (4) a review of the various operations and their potential future development; (5) the criteria for rope replacement; (6) potential future developments that could take place in both hoisting and rope inspection practices in Canada; and (7) recommendations.Subsequently, the report was issued by OMOL, and as a CD-ROM by CANMETMMSL. In this paper the author presents the key findings and the recommendations made in the study."

Jan 1, 2004

By Peter Silveston, Earl Shannon

Process-oriented experiments on the use of coal as an adsorbent for certain soluble components of sewage are described. The capacity of Canadian coals for these components was less than 0.1 per cent by weight for the highest concentration at which these components could be expected to be found in domestic sewage. This is much less than values reported in the past. A pronounced selectivity between components was observed. Experiments on bacteria removal in beds of coal, regeneration of spent coal to restore adsorption capacity and COD contributions of coal are reported in the paper. The simple application of coal as an adsorbent does not seem promising.

Jan 1, 1970

By J. Chelsey Dawson

In presenting a thesis on this subject it is advisable to explain a few of the reasons for its seeming incompleteness. World progress has brought us to a position where approximations are not only to be condoned, but regarded as absolute essentials. Production in anticipation of demand is always accompanied by mistakes on the part of the producers. Only through trial and sometimes erring hypotheses may there be evolved the true course and theory upon which the steady triumphant march of world-wide industry depends. The average person likes to have everything placed ?before him in a clear and convincing manner. It is the impossibility of doing this which, in many cases, arises to confound the writer on shales. All that one can do is to present, as lucidly as possible, the known hypotheses' and theories on the subject and leave the reader to study and work out the truth for himself. Many theories have been advanced on the origin of oil-shales ; some may be correct in certain instances and not in others; however, the writer will attempt no decision as to which are and which are not correct, but .will merely point out the relative merits of each. The figures given for reserves of oil and shale in different countries are only approximations and give but a rough idea of the true conditions.

Jan 1, 1925

By H. Ranjbar

The Darrehzar porphyry Cu deposit is situated in the Urumieh-Dokhtar magmatic suite of Central Iran. The REE and trace element data suggest that the deposit lies within a continental margin setting. Phyllic and propylitic alteration are pervasive in the area but potassic and argillicalteration are not readily recognized on the surface. This is possibly the result of super gene weathering of the surface rocks or because of an intense phyllic overprint. Poor soil development and abundant outcrop make the area suitable for a case study of lithogeochemical exploration technique for Cu deposits. A total of 262 rock samples was collected over the area and analyzed for 15 elements. The geochemical data cor-relate with the mineralogical composition of the rocks with the phyllic zone being marked by high-er concentrations of Si, Al, K, and by a high sericitization index while Ca, Mg, Sr, total Fe and Mn are more abundant in the propylitic zone. The lithogeochemical study indicates a metal zonation from a Cu + Mo-rich core to a Zn + Pb ± Ag-rich outer zone. Principal component analysis is useful for separating element associations, which in turn reflect the alteration halos. Principal components 1 and 2 depict alteration zoning, where-as 3 shows an association of Cu and Mo, that roughly defines the mineralized area.

Jan 1, 1997

By Clifford S. Gibson

A year ago a paper (1) was presented at the Annual Western Meeting of the Institute regarding silicosis in Ontario mines. It described the whole problem as we see it and discussed the means of prevention. The work and aims of the Technical Silicosis Research Committee of the Ontario Mining Association, and of the Committee's field engineer, were fully described also and it is suggested that reference be made to this paper in order to have a better understanding of the observations which are presented now. These observations enlarge upon parts of the dust control measures already discussed and tell of general progress in the past year. They concern fifty properties, the majority of the operating mines, which vary in size from the hopeful prospect to established producers yielding 11,000 tons of ore daily. Most of these are gold mines; a few copper-nickel. The ores range from heavy sulphides to siliceous materials and they are mined by many methods from varying types of deposits. The majority of the latter are steeply dipping and all are found in Precambrian host-rocks. Up to the present, die greatest depth to which mining has penetrated is 6,400 feet.

Jan 1, 1939

By R. T. McAndrew

Introduction Drinnan is situated in the Prairie Creek coal area in the Foothills belt of Alberta. It lies on the main line of the Canadian National railway from Edmonton to Jasper. The exact location is shown on the map (Figure I). Interest in the field was aroused by several circumstances: Its proximity to Brule and Pocahontas on the southwest and to Coal-spur on the southeast led to the belief that coal might be economically produced here. There was already at Hinton a 3 ft. 9 in. coal seam being mined by Seabolt. The coal was of very good grade, being black and shiny in appearance with well defined cleavage and a heat value of 12,000 B. t.u. Outcrops of coal had also been noticed on the north side of the Athabaska river and Fish creek. These facts led the Jasper Coal Company to investigate the field. This Company considered taking over the Seabolt property at Hinton, but, owing to the size of the seam, this plan was abandoned and prospecting by diamond drills and test pits was started two years ago in the district east of Hinton. After prospecting had been completed, the most favourable district was found to be in township 51, ranges 24 and 25, west of the 5th meridian. The Company's lease includes all or parts of sections 18, 19, 20, and 28 in range 24, and sections 10, 11, 12, 13, and 14 in range 25. The approximate boundaries of the property are the Canadian National railway on the north, Happy creek on the west, and Cache Percotte creek on the east. The lease comprises 3,100 acres, and the total amount of coal in sight is estimated at 100,000,000 tons.

Jan 1, 1931

By R. Viljoen, K. Manns

"The mining industry instinctively follows rule-of-thumb design velocities often based on very simplistic theoretical “economic velocity” optimization calculations to determine airway sizes. Although these are important building blocks in ventilation planning it should be recognized that mines are far more complex and various, often opposing factors, are at play. Therefore, it is important that each ventilation situation be analyzed on a case-by-case basis to determine the best-fit solution for an operation. The ventilation design process should not necessarily be constrained by theoretical optimal economic velocities that become rules-of-thumb. In some cases, this could lead to unrealistic infrastructure requirements and exorbitant capital expenditure. This type of design often lacks corporate support leading to a scenario where no ventilation upgrades are implemented. Economic velocities typically consider the cost of power, development costs and operational risk. These typical rules-of-thumb work reasonably well as a starting off point when considering feasibility of greenfield projects. For established mines that are looking at expansion these rules may not be appropriate due to capital expenditure constraints or geotechnical ground conditions. The theoretical optimum should be reviewed in the case of an established mine where existing infrastructure could perhaps be maximized. For example, the geotechnical risk of large diameter raises at depth may require multiple small diameter raise to maintain the theoretical economic velocity. If a mine has a life of less than 5 years, then the cost of power is an insignificant proportion of the total owning cost. For these mines, operating the ventilation raises at an increased velocity to avoid a complicated and expensive capital upgrade might be the more appropriate option, even though it opposes the traditional rules-of-thumb. Mines which are capital constrained may be better off accepting a higher operating cost for the interim or settle for minor infrastructure upgrades rather than run the risk of the entire ventilation upgrade not being approved at all. This paper explores a number of examples derived from case studies undertaken by the authors for several deep mechanized mining projects in Australasia. The examples explore conditions under which higher than the economic norm would be applicable."

Jan 1, 2019

By D. M. Doyle

A study of the various components contributing to energy costs and their relationships to generally trended operating data, such as tonnage, operating costs, etc., over progressively shorter time periods provides information for an energy audit. A study of annual data gives some insight into the importance of various energy components. As the time frame of the study progresses through monthly, daily and, finally, into quarter hourly data, the variations become more evident and, most important, strategies develop to minimize energy costs. The results of an audit conducted during the summer of 1978 at Wesfrob Mines Limited are reported to illustrate this important phase, prerequisite to a meaningful energy cost avoidance program. The balance of the paper deals with the energy conservation program at Falconbridge Nickel Mines Limited's Sudbury operations, the metering and control equipment, the commitment, the new energy accounting practices and, lastly, the policies. Examples of successful energy conservation endeavours include automatic peak electrical load control, waste heat recovery from mine air and compressor cooling water, energy reductions resulting from lower building temperatures and curtailment of idling loads. The use of pulse meters to measure the flow of gas, steam, compressed air and electrical energy, with their signals interfaced to process computers, allows monthly, daily and, if necessary, immediate reporting of energy and energy per unit of production information The program so reported at Falconbridge's Sudbury Operations is credited with an annual cost avoidance of .9 million dollars in a 14.0-million-dollar annual energy account

Jan 1, 1979

By Maureen Jensen

For mining companies looking to establish a strong North American presence, raise their profile or finance and position themselves for future growth, there is no other destination in the world that can offer a mining company the same opportunities as Canada whether you are an established blue chip or promising junior. Despite historically poor world commodity markets and shaky investor sentiment towards junior explorers caused in part by fallout from the high profile Bre-X fraud, Canada continues to shine as the undisputed mining finance capital of the world. Our natural riches and mining history go a long way to explain Canada's international prominence in mining finance. Canada has actively created and maintained one of the most integrated national frameworks to support mining ventures of all kinds. Our diverse industry, from one-person grass-roots explorers to mining industry giants, is one of our main strengths whether your company is Canada-focused or internationally active. The mining industry continues to be a vital contributor to the Canadian economy, contributing $26.2 billion in 1997 or 3.8% of national GDP, and is the second largest earner of foreign exchange. Industrial mineral companies are a very important part of this strength. These companies require a continuing access to capital to ensure that they can continue to compete and the globalisation of the Canadian mining industry has affected this industry just as much as it has affected every other industry in Canada.

Jan 1, 2001

By G. B. Langford

UOCK bursts are a phenomenon about which insufficient is known. This l.~ statement has a twofold meaning. In the first place, far too many people, both inside and outside of the mining industry, are woefully ignorant of the whole subject, and secondly, as those who are face to face with the problem in the mines realize, our knowledge of rock bursts is inadequate. The first group embraces the general public, who have never been enlightened on the subject, and a great many geologists and engineers who have never shown more than a curiosity about it. Such technical men do not realize what a vital problem it is to our mining industries. They are usually thankful that bursting ground is not their problem, and leave it to those unfortunate enough to run into it. From such men one often hears the pious opinion that if proper mining methods were used there would be no problem. It is hoped that this paper will give these people a different viewpoint. Those in the second group deserve much credit for what they have done and are doing. They are fighting a large and difficult problem. In the pages that follow, I have tried to give a bird's-eye view of that problem, and suggest new ways in which it may be attacked.

Jan 1, 1941

By François Robichaud

"The Laronde mill has been in operation since 1988. Actual milling rate ranges from 7,000 to 8,500 mtpd. Laronde uses SAG/ball mill grinding followed by copper and zinc flotation circuits. A cyanidation/Merrill-Crowe process recovers the remaining gold and silver in the flotation tails.In 1999, the carbon in pulp circuit was replaced by a Merrill-Crowe circuit in order to cope with a much higher ratio of silver/gold associated with the discovery of the Penna shaft. Marine type diatomaceous earth was used as filter aid in both clarifier pressure leaf filters and recessed pressure filter presses from 1999 to 2005. In 2005, this filter aid was gradually replaced by alpha-cellulose after several laboratory and plant filtration trials. The selected cellulose is considered to be much less sensitive to parameters such as pH and reagent concentration and have increased clarifier and filter press filtration performance. Also, since cellulose is exothermic, replacing diatomaceous earth with cellulose as filter aid in the filter presses has increased calcining and oxidation rates in the calcining ovens since cellulose is exothermic. Finally, better calcining conditions have resulted in energy and reagent savings at the arc furnaces.This paper describes how the filter aid replacement has contributed to increasing productivity and Net Smelter Return of the refinery while reducing worker’s hazards and operating cost.INTRODUCTIONAll Merrill-Crowe circuits in the world are operated with filter aids. For years, the market for precoat filter aid has been dominated by mineral filter aids such as diatomite and perlite. Flowsheet and equipment selection at the Laronde refinery were performed in the late nineties. At that time, some key parameters of the design criteria had clearly identified marine type diatomaceous earth (DE) as the most successful filter aid. Parameters such as reagent cost and availability, clarity of the filtrate solution and good historical filtration performance in other concentrators had designated DE as the best suited filter aid. Pregnant solution processed in the refinery from its start-up through 2001 was fairly stable in flow rate and reasonable in terms of impurity content (cationic and anionic compounds)."

Jan 1, 2007

By X. Wu

Tunnel Boring Machines (TBMs) are widely used for tunneling in urban areas because of their high advance rate, precise as-built profile and minimal impact to buildings and traffic on the ground. For a tunnel built by a TBM, there are strict requirements on alignment control and safety. To meet these requirements, it is important to monitor the position of the TBM. In the current practice, the TBM position data, including advance distance and line and level deviations, are reported manually to the managers on a daily basis. To interpret and analyze the position data, the managers also need to refer to various construction drawings. This practice is untimely, inefficient, and error prone for decision making. To improve the current practice, an automatic approach for real-time as-built tunnel product modeling and visualization is proposed, based on TBM position and orientation data autonomously sourced from the Virtual Laser Target Board (VLTB) TBM Guidance System developed at University of Alberta. Related information of the tunnel project, such as the as-designed alignment, soil layers, the ground, existing utility lines, is also visualized together with the model of the as-built tunnel. The modeling algorithm is presented step by step. Its application in a real-life drainage tunnel project is discussed and limitations are also identified.

Aug 1, 2013

By E. J. Marcotte

"INTRODUCTIONThe Upper Canada Mine is located at Dobie, approximately ten miles east of Kirkland Lake, Ontario.The mill contains Upper Canada's cyanide circuit and Upper Beaver's flotation circuit. The combined capacity is 590 tons per day consisting of 415 t.p.d. of Upper Canada gold ore and 175 t.p.d. of Upper Beaver copper-gold ore.The Upper Beaver ore is trucked five miles to the Upper Canada mine site.Crushing:The crushing circuit consists of primary, secondary and tertiary crushing employing one C .A. C. 15 in. x 24 in. Superior jaw crusher, one 4 ft. x 8 ft. Tyler-Niagara double deck screen, one 3 ft. Symons standard cone crusher and one 3 ft. Symons shorthead cone crusher.The -2 in. product from the jaw crusher is fed to the double deck screen. The+ 5/ 8 in. passes over the top deck to the 3 ft. standard cone crusher; the+ 3/ 16 in. material passes over the lower deck to the shorthead cone crusher. The - 3 / 16 in. material pas sing through the lower deck of screens is the product to the mill.The screens used prior to the installation of rubber screen cloths were: one 4 ft. x 4 ft. section with 3/ 4 in. square openings and one 4 ft. x 4 ft. section with 5/ 8 in. square openings on the top deck; two 4 ft. x 4 ft. sections with openings of 3/16 in. x 4 1/2 in. slot on the lower deck. The fine screens were positioned so that the 4 1/ 2 in. slots were parallel to the flow of feed.The crushing circuit is operated on a three shift per day basis by one operator per shift."

Jan 1, 1968