Search Documents

By Lionel A. York

THE first application of the cementation process took place in the year 1864, according to H. Standish Ball, when a break in the brickwork lining at a depth of 270', in one of the Rhine Preussen pits near Homburg, was sealed by running in milk of cement from the surface by means of a small hand pump. At about the same time Monsieur Portier adopted the method in France for repairing breaks in shaft lining. Figure 1 is descriptive of the Portier system and is of interest when compared with modern practice. During the next thirty years numerous attempts were made to improve the process; the general method used in sinking being to put clown bore holes outside the perimeter of the shaft for the purposes of injection. The cementation process was first recognized as an important as-set to mining in 1896 when Monsieur A. Francois developed his method of boring and injecting inside the shaft below the permanent water level. The Francois cementation process rapidly attained fame on the Continent and many shafts were sunk by its use in France, Belgium and

Jan 1, 1961

By Dave Ecobichon, Éric Côté, Simon Nickson, Michel Leclerc

The feasibility assessment of a mineral deposit requires the construction of a geo mechanical model of rock mass properties, for the purpose of preliminary mine design. The Noranda Technology Centre has been involved in the development of geomechanical models for several mineral deposits at the feasibility stage. Each model is constructed through intact rock testing, geotechnical core logging, geotechnical mapping and rock mass classification. Rock mechanics principles are used to develop conceptual stope designs and propose possible mining sequences. This methodology is applicable to both new mining projects and to the development of new areas within anoperating mine. This paper explains how the geomechanical model is developed and reviews its application to several case studies.

Jan 1, 1996

By D. K. Sarkar, Jiawei Xiong

"Self-assembled monolayers (SAM) on the aluminum substrates are used as the adhesion promoter between two aluminum substrates when bonded with the adhesive in adhesive bonding technology. Traditional surface analysis tools are not capable of identifying the presence of SAM on a surface; therefore, EIS has been used to determine their presence on the aluminum substrates. In this study SAMs have been deposited on aluminum using the monomer of (3-Glycidyloxypropyl)trimethoxysilane (GPTS) organosilane. AA6061 aluminum alloys substrates were chemically cleaned with NaOH and HNO3 to remove the native oxides, followed by immersion in silane solutions. In a second method, SAMs were prepared by applying a spin coating of silane solution to the samples. The prepared SAM coated aluminum samples were analysed by EIS in the three electrode corrosion cell using a diluted alkaline solution. The impedance of the SAM coated aluminum is found be higher than the as-received aluminum. It has been also observed that the open circuit potential (OCP) of the SAM coated aluminum is higher than the as-received aluminum. Both elevated values of the impedance and OCP confirm the presence of SAM on aluminum.INTRODUCTIONSelf-assembly (Schreiber, 2000) is defined as the spontaneous formation of complex hierarchical structures from pre-designed building blocks, typically involving multiple energy scales and multiple degrees of freedom. Generally speaking, SAMs are created by the chemisorption of ""head groups"" onto a substrate from either the vapor or liquid phase followed by a slow organization of ""tail groups"" of a molecule. Typically, head groups are connected to a molecular chain in which the terminal end can be functionalized with groups such as –OH, –NH2, –COOH, or –SH to vary the wetting and interfacial properties (Chauhan et al., 2007; Ulman, 1996; Vashist, Lam, Hrapovic, Male, & Luong, 2014). Though there exist several methods to prepare SAM (Chauhan et al., 2007; Chen, Yang, & Zhang, 2014; Cho, Park, Jon, & Choi, 2007; Igor Luzinov, 2000; Reis, de Melo, & Costa, 2006; Song, Zhai, Wang, & Jiang, 2006; Sugimura, Hozumi, Kameyama, & Takai, 2002; Vashist et al., 2014), the two methods vapor phase (Song et al., 2006; Sugimura et al., 2002) and solution(Chen et al., 2014; Igor Luzinov, 2000) are commonly used. Recently, many articles have been published on the fabrication of superhydrophobic surfaces with SAM technology (Cho et al., 2007; Pan, Shen, Shang, & Xing, 2012; Siddaramanna, Saleema, & Sarkar, 2014; Song et al., 2006). Brassard, Sarkar, and Perron (2011) successfully obtained a superhydrophobic film by applying fluoroalkylsilane via self-assembly on monodispersive silica. SAMs are also reported as good candidates for anti-corrosion and adhesion promotion (Chen et al., 2014; Saleema, Sarkar, Paynter, Gallant, & Eskandarian, 2012). However, papers on the characterization of SAM properties are rarely seen. The most commonly used substrate for SAM is silicon and the method implemented is scanning probe microscopy (SPM) such as atomic force microscope (AFM) (Igor Luzinov, 2000; Moores, 2011; Zhang, 2003, 2005). Igor Luzinov (2000) analyzed the epoxysilane SAMs’ surface morphology and microstructure properties using scanning probe microscopy (SPM) and ellipsometry on single-crystal silicon wafers. SAMs have been used to improve the adhesion bonding of aluminum or plastics but no characteristic data have been presented yet (Saleema et al., 2012; Telegdi, 2007; Wang, Xu, Luo, Wang, & Wang, 2009). Recently, Reis et al.(Reis et al., 2006) have studied SAM of alkane diphosphonate (Gardobond X4661) on Al 5052 alloy samples by EIS in a naturally aerated sodium sulfate solution."

Jan 1, 2016

By D. B. Hyma

"The Raglan Ni/Cu property is located on the Ungava Peninsula in Northern Quebec, Canada, at a latitude of61°42' and a longitude of73°40', approximately 40 km southwest of Douglas Harbor. Geological reserves are estimated at 18 million tonnes, grading 3. 1 % nickel, 0.9% copper and smaller amounts of cobalt and platinum group metals.Extensive project development has defined the concentration process, concentrator sizing, tailings and environmental management required for this project.The grinding circuit selected is a fully autogenous primary grind, with pebble crushing and a pebble mill for secondary grinding to produce a product of 80% -70 microns for flotation.The flotation circuit is a simple circuit utilizing roughing, a regrind of rougher concentrate to 80% -20 microns, two stages of column cleaning with a cleaner scavenger bank on the column tails.Concentrate handling options were thoroughly reviewed because of the pyrophoric nature of the concentrate, remote site location and long distance to downstream processing. The preferred option, currently.is to dry the concentrate at Raglan to less than l % moisture and then pneumatically handle the powder.A detailed analysis of tailings placement options, suggests filtered tailings placement to be the preferable route for the Raglan site.INTRODUCTIONThe Raglan Project, as proposed by Falconbridge Limited, will develop extensive nickel-copper deposits in the Ungava Peninsula, Quebec, Canada. The project schedule and construction conditions in the project area are demanding. The Raglan mineral deposits have been the subject of numerous studies and evaluations over the last thirty years and the Phase I 1991 pre-feasibility document includes exploration information obtained in the 1989 and 1990 drilling seasons. This review concluded that an 800,000 tonnes of ore per year mining and concentrating complex located at Katinniq could produce 20,000 tonnes per year of nickel at competitive costs."

Jan 1, 1993

By G. G. Manekar

MOIL Limited (formerly Manganese Ore India Limited), a Government Enterprise, under the Ministry of Steel, Government of India, produces about 1.1 million tonnes (T) of manganese ore annually from three opencast and seven underground mines. The underground operations are mining using an overhand cut and fill method. The orebody is too narrow for the use of larger equipment and the poor to fair rock mass quality limits the size of stable excavations. Prior to the 1990s underground support consisted primarily of timber square sets in tandem with timber chocks and props. As mine production requirements increased throughout the 1990s led to larger opening sizes and more modern support practices. Research was conducted on ground support design based on rock classification and empirical techniques for designing ground support. Based on the findings and field trials, the Company adopted full column cement grouted cable bolts for back support. Instrumented field trials, using extensometers and load cells on the cable support confirmed the support effectiveness. Stope design was based on two and three dimensional stress modeling which resulted in a significant increase in stope dimensions. The rock mechanics studies for safe stope design were carried out using numerical modeling tool in two and three dimensions for the analysis of stresses. Based on the findings, the safe stope geometry with new stoping parameters was introduced. The earlier stope length of 30 mtrs were changed to 60 mtrs with in situ rib pillar at the cross cuts and in situ post pillars to be left-out in the stope. This leads the formation of of panel comprising of three stopes, for production, supporting and filling. For mechanical handling of ROM in stopes Side Discharge Loaders (SDL) were introduced. The above changes have improved the face productivity from 2?3.5 T with manual operation and 9 T with SDL. The above rapid mining operations has improved the stope productivity but reduced the stope life from 6 to 3 years. For the improvement of the stope availability, further studies were conducted by numerical modeling of stress analysis. The related studies confirmed that with the existing supporting system and proper instrumentation, level interval could be increased up to 45 mtrs from the existing 30 mtrs at deeper levels. At present below 12th Level interval is 45 m at Balaghat Mine. For future mechanization program for introduction of Single Boomers, LPDT, Cutting Machines etc for the development headings rock mechanics studies are underway. The paper provides details of rock mechanics studies that were carried out to study efficacy of the cable bolt support, safe stoping parameters and increased level interval for the improvements in safety, production and productivity at Balaghat Mine.

Aug 1, 2013

By Ye Chen, Jianhua Chen, Xianhao Long, Qingxia Liu, Zhenghe Xu

"It is crucial to understand the mechanism of the collector interacting with the mineral surface in the presence of water molecules, which could influence the relaxation and electronic properties of sulphide mineral surface due to the proximity effect for narrow band gap of semiconductors. The adsorptions of three typical collector molecules (xanthate, dithiocarbamate and dithiophosphate) on the sulphide mineral surfaces in the absence and presence of water molecule have been simulated by density-functional theory (DFT). The calculated results show that the adsorptions of collectors on clean mineral surface in vacuum are not in agreement with the observed flotation behaviours. The presence of water molecules has a great influence on the adsorption of collectors. The analysis of density of states of the mineral surface atom suggests that the adsorption of water molecules could influence the electronic properties of mineral surface and consequently influence the adsorption between the surface and the collector molecule.INTRODUCTIONIn the separation of multi-metal sulphide ores, the selectivity of a collector is a key factor for the efficient recovery of the aimed mineral. Xanthate, dithiocarbamate (DTC) and dithiophosphate (DTP) are the most common collectors used in the flotation of sulfide minerals. Generally, xanthate exhibits powerful collecting property but lack of selectivity. While dithiophosphate and dithiocarbamate show the good selectivity in the lead and copper sulphide mineral flotation. The mechanisms of these collectors interacting with the sulphide mineral had been attracted many attentions and several mechanism based on experimental results had been reported (Chander & Fuerstenau, 1974; Fuerstenau, 1990; Raju & Forsling, 1991; Crozier, 1991; Bradshaw, Cruywagen & O’Connor, 1995; Guler, Hicyilmaz, Gokagac & Emekci, 2006). However, the micro-mechanisms of the selectivity of these three thiol collectors on different sulphide mineral surfaces are not fully understood."

Jan 1, 2016

By O. A. Carson

"IntroductionTHE ZINC-BASE die casting alloys in common usage contain approximately 4 per cent aluminum as the major alloy element. In addition, they contain about 0.05 per cent Mg .and may• have a small amount .of copper. These are usually the only •elements intentionally present.Small amounts of some impurities have been shown to have a deleterious effect on the properties of these alloys and therefore the impurities are kept low by starting with '99.99%' zinc.The reasons for holding the aluminum content at 4 per cent are not clear. Some statements appear in the literature that higher aluminum increases the brittleness, but probably the chief reason was the relative price of zinc and of aluminum when 4% alloys became firmly established. At that time, aluminum was three to four times the price •of zinc on a weight •basis. Recent prices, roughly equivalent per lb., make aluminum considerably cheaper than zinc on a volume basis and suggest that increased aluminum content would result in a decrease in the cost per piece due to the lower density of the alloy.Little information could be found in the literature and, therefore, it was decided to determine some physical properties of the higher aluminum zinc-base alloys made from high-purity zinc."

Jan 1, 1953

By Chun-Sheng Liao, Chun-Hua Yan, Sheng Wu, Fu-Xiang Cheng

"INTRODUCTIONChina is providing more than 90% of the rare earth products consumed in the whole world. Acidic extractants are commonly used in the extraction separation of rare earths. Saponification of the acidic extractants by basic substances is usually necessary for the purpose of increasing and stabilizing their extraction capacity, and meanwhile inorganic acids are required for both scrubbing and stripping. Thus acids and bases are the main consumed chemicals, and the resulting salts are the main pollutants generated by rare earth separation processes. Currently, due to increasing environmental concerns in China, rare earth solvent extraction separation techniques are being developed to reduce both consumption and emission of chemicals, which is driving the developments on both theories and processes for solvent extraction separations.In the 1970s Prof. Xu et al. developed the Theory of Countercurrent Extraction (Xu, Li, & Yian, 1985). In recent years, the development of novel processes for rare earth separation has moved beyond the earlier theory. One rare earth separation process, the so-called hyperlink process, has been developed in the past decade and proven in industrial practice to dramatically reduce both the consumption and emission of chemicals during multi-component solvent extraction separations, and therefore is now widely used in the Chinese rare earth separation industry (Liao, Wu, Cheng, Wang, Liu, Zhang, & Yan, 2013). The present article will give a brief review of the development of the theory of the hyperlink processes, and the hyperlink separation flowsheets for typical rare earth mines in China designed using the theory.HYPERLINK PROCESSES (LIAO et al., 2013)A flowsheet of multiple-component separation consists of a couple of separation units. The units of a conventional flowsheet separately consume chemicals for saponification and scrubbing and discharge wastewater with resulting salts. In contrast, the separation units in a hyperlink process are hyperlinked and thereby the chemical demands of the whole flowsheet are decreased. For a feed containing t components of A1, A2, …, and At, it has been proved in theory that the separation mode of (AtAt-1…A2)/(At-1At-2…A1) is preferred in a single separation unit. The hyperlinking between separation units can have two forms. The link between two units locating at a same separation level, such as between (A4A3)/(A3A2) and (A3A2)/(A2A1), is known as horizontal hyperlinking. The link between two units located on different levels, such as between (A4A3A2)/(A3A2A1) and (A3A2)/(A2A1), is known as vertical hyperlinking. Both the hyperlinking forms have been proven to save chemical usage and consequently to lower the pollution emissions in industrial practices as well as in theory."

Jan 1, 2016

Several inorganic reagents and organic polymers were tested as depressants in the single mineral flotation of ultrafine iron oxide and hydroxylapatite with Dowfroth 250 as a frother. It was observed that the inorganic reagents and the low molecular weight polymers generally caused dispersion of the ultrafine particles, and consequently their recovery into froth products more or less equaled the recovery of water. On the other hand, the high molecular weight polymers caused different degrees of flocculation of the ultrafine particles, and their recoveries were much lower than the recovery of water. These observations pointed to a need to re-define flotation depressants in fine particle flotation. The traditional definition of a flotation depressant, i.e., to make particle surfaces hydrophilic by forming a hydrophilic film and/or by removing collector and activator coatings, is sufficient for relatively coarse particles. However, to prevent fine and ultrafine particles from floating, a successful depressant should not only make the particles hydrophilic, but also enlarge the particle sizes so that they do not enter the froth product by mechanical entrainment. Polymeric depressants are ideal for these purposes. The different schemes to use polymeric depressants in the selective flotation of fine and ultrafine particles were discussed These schemes involve the integration of the polymeric depressants into other size enlargement processes such as shear flocculation, oil agglomeration, etc., for hydrophobic particles.

Jan 1, 2004

By M. Imani, A. Fahimifar, A. H. Javid

"Current studies of bearing capacity for shallow foundations tend to rely on the hypothesis of an isolated footing. In practice a footing is never isolated; it is mostly in interaction with other footings. This paper focuses on a numerical study to evaluate the ultimate bearing capacity for two interfering strip footings resting on a rock mass in which the strength can be described by the generalised Hoek–Brown failure criterion. This criterion is applicable to intact rock or heavily jointed rock masses that can be considered homogeneous and isotropic.The material is assumed to exhibit perfect plasticity and obeys an associated flow rule. The effects of Hoek–Brown parameters including GSI, mi, and sci were studied and the corresponding results are presented. For different clear spacing (S) between the footings, values of the efficiency factor (?) were determined; where ? is defined as the ratio of the failure load for an interfering new footing of a given width (B) to that of a single isolated footing having the same width. The maximum value of (?) occurs at spaced between S/B = 0.5 to 1.0. The results have been compared with those available in the literature.INTRODUCTIONEvaluating the ultimate bearing capacity of rock masses is essential for important projects like dams and bridges. Closely spaced footings may occur on rock masses in the form of pier foundation and grillage footing. Close spacing lead to permit higher loads than can be bore by similar isolated footings. The ultimate bearing capacity of two interfering strip footings resting on cohesionless soil have been studied theoretically (Kumar, & Gosh, 2007; Kumar, & Kouzer, 2008; Stuart, 1962). Results revealed when two strip footings approached closely enough, failure zones affect each other and ultimate bearing capacity significantly increased."

Jan 1, 2015

By H. C. Gunnings, C. O. Swanson

"The Sullivan mine; at Kimberley in southeastern British Columbia; is the largest silver-lead-zinc mine in the Empire and one of the largest in the world.The original discovery was made in 1892 by four prospectors. Until 1899, when the branch line of the Canadian Pacific railway from Cranbrook to Kimberley was completed, little work was done on the property. In 1900, systematic development was started, and during the next 3 years 5,000 tons of ore was shipped to the smelters at Nelson and Trail. By 1903, some 300,000 tons of ore was developed, and a smelter was started at Marysville, about 5 miles from the mine. However, this smelter closed down in 1907 because of metallurgical difficulties after treating 75,000 tons, and the property came under the control of the American Smelting and Refining Company. An option on the property was taken in 1909 by the Consolidated Mining and Smelting Company of Canada, who exercised their option in the following year. During the next 5 years by selective mining and sorting 188,000 tons of high-grade ore was produced and shipped to Trail. This tonnage came from the upper levels, about 4,600 to 4,800 feet in elevation. At the same time, deep drilling down to the 3,900-foot level showed the presence of an immense body of complex ore. In 1915, the main adit-the 3,900-foot level-was started, and by 1919 this had been driven a distance of 2 miles to develop the ore above this level. Meanwhile, progress was being made in overcoming the milling problems. An interesting account of this work was written by the staff ( 4). In 1923, the first unit of the present concentrator was erected, with a capacity of 2,500 tons a day, and thereafter the rate of production increased rapidly. In 1934 it was around 8,000 tons a day, and to date a total of about 30,000,000 tons of ore has been sent to the mill. In recent years, a considerable part of the production has come from levels between the 3,900-and 3,350-foot, which were opened by an internal incline shaft started in, 1930. In 1942, tin was added to the products separated at the concentrator."

Jan 1, 1954

By Z. G. Tao, Y. Y. Peng, W. L. Gong, M. C. He

"This paper presents an overview of the major landslide hazards in open pit mines in China, the currently used landslide control and monitoring techniques, and development of a new slope control technique incorporating the reinforcement, sliding force monitoring, remote sensing and forecasting in one system in order to constrain the displacement of the sliding blocks in the landslide to minimized the influenced area and provide precise warnings timely for the imminent landslides. For implementation of the new technique, a novel rock cable with large deformation and high resistance (also known as HE cable) was developed, which can elongate as long as 2m. At the same time, the necessary and sufficient condition for initiating a landslide and energy balance equations are formulated. Based on the proposed mathematical models and Beidou satellite system, the software and data transmission hardware for remote sensing and forecasting were developed the new landslide control technique has been applied successfully in 245 landslide sites in 12 provinces across China. In this article, two practical application cases in the open pit mines are reported.INTRODUCTIONChina is one of the countries in the world with the most widely distributed landslides and suffering the heaviest damage. According to the incomplete statistics, landslide hazards have caused death of hundreds of people and direct economic losses of several hundred million RMB each year. The landslide hazards have a great impact on the life and property safety of the people, safety of the infrastructure, as well as the social stability. Thus development of new techniques for forecasting and prediction of the landslides is imperative and of great importance. In general, the forecasting and prediction of the landslides consists of three major aspects, i.e. sliding time forecasting, landslide activity intensity forecasting and landslide hazard degree forecasting. Since a considerable part of the landslide-suspected area are adjacent to the residential areas or important infrastructures, development of the advanced landslide control and monitoring techniques to cope with the sliding time forecasting problem is more important.Over the past one hundred years, the most widely used slope monitoring techniques are based on displacement monitoring (Xu, et al. 2007; Toshitaka, 1998). In the early days owing to the limitation of the technology and equipment, the ground surface displacement and underground water level change were inspected mainly by man power for inferring the possibility of a landslide. In recent several decades, more and more ground surface displacement monitoring devices were brought to the market, such as the automatic total station, theodolite, digital level, borehole inclinometer and GPS based instruments, etc. Based on these modern techniques, some advanced instruments have been developed and applied to the landslide monitoring, for example, the “landslides early warning monitoring system” (Leonardo, et al. 2002), the “In-SAR” technique (Reevea, et al. 2000), the GPS and satellite geodetic survey based technique (Reevea, et al. 2000), and real-time telemetry technology (Xu, et al. 2007). These monitoring approaches have made significant contributions to the landslide disaster monitoring and forecasting. The major limitations for the ground surface displacement monitoring techniques are lie in the inconsistence between the displacement in ground surface and that in the sliding surface for the sliding mass, resulting in low degree of forecasting accuracy."

Jan 1, 2015

By Harry Perry

By 1980, the free world's need for economic sources of energy is expected to double. As a result, there will be a tremendous potential for all energy sources working together to supply the demand. For coal to continue its dominant role as a low-cost energy source, means must be found for it to meet the challenge of nuclear power and to overcome obstacles placed on its use by air and water pollution regulations. As the more limited reserves of gas and oil diminish, economic ways are also required for converting coal to synthetic liquid and gaseous fuels, and to chemicals, thus resulting in optimum utility of the most abundant low-cost fuel resource. The means for accomplishing these ends can only come about by a vigorous research and development program. Successful efforts by industry and government working together, both in America and abroad, will assure the continued use of coal to meet the world's energy demands. This paper discusses the emerging patterns of energy sources throughout the world and the role that research and development on coal will play in supplying future energy requirements.

Jan 1, 1967

By V. L. Eardley-Wilmot

Introduction We are all familiar with the bright and attractive colours of the roofs of our suburban houses and country cottages, but few of us fully appreciate the complex and highly technical nature of the business which produces these roofings. Roofing granules consist of small broken particles of certain types of rocks, burned clay products, or slag. They are used either in their natural state or artificially coloured and are affixed onto one surface of asphalt sheeting. Their main functions are to protect the roof against external fire hazard, prolong its life, and enable it to withstand extremes of weather over a period of years without deteriorating. Pleasing designs and colours are added attractions. The reverse, or inner side, of the sheeting is coated with a film of talc or fine mica to prevent it sticking when rolled up for convenience of handling for transport. The finished sheets or strips are cut into a variety of shapes for roofing shingles, or for sidings which resemble rows of bricks separated by mortar. In Canada, the consumption of roofing granules has increased fourfold in the past decade and indications are that the industry will continue to expand. At present, fourteen plants are engaged in manufacturing granule-coated roofings, but, apart from a relatively small output of natural granules by two producers in British Columbia, only one eastern producer makes both natural and coloured granules in Canada, and these only for its own use. The annual consumption is now over 77,000 tons of roofing granules valued at more than $1,600,000, but about 62 per cent of the tonnage is imported. It is thus apparent that the production of Canadian-made granules, both natural and coloured, could be considerably increased. This paper is presented in order to give an outline of the industry and at the same time to point out its difficulties and pitfalls.

Jan 1, 1946

By G. Morin, F. Chiesa, B. Duchesne

The Quality index is a useful tool allowing to assess the metallurgical quality of aluminium AlSiMg foundry alloys (A356/357). Its value is calculated from the ultimate tensile strength and elongation; it increases with the metallurgical quality of the casting, i.e. with finer dendrites, lower microporosity and inclusion count and lower iron content. This Quality index does not depend on the degree of temper applied during the heat treatment (aging time and temperature). After defining the Quality index, it will be explained how it can be predicted from the knowledge of the local solidification conditions obtained from modelling. The paper will then present four case studies of castings for which the prediction of the Quality index by modelling was made. These case studies from different authors will involve the three most common casting processes used for producing high integrity aluminium castings, namely: sand casting, permanent mould casting and investment casting (lost wax). In all cases, the accuracy of the prediction will be assessed by comparing the predicted Quality index distributions to the experimental values based on the published measured values of the local tensile properties.

Jan 1, 2006

By A. W. Jolliffe

AEROPROSPECTING may be defined as the application of the air view to the search for mineral deposits. The term is suggested as a preferable alternative to either aerial prospecting (which may be confused with areal prospecting) or air prospecting. The air view may be obtained by visual observation from an aircraft or by examination of air photographs; each has its particular advantages and disadvantages. Aeroprospecting should be regarded only as an aid to, and not as a substitute for, accepted prospecting methods ( l ). The Precambrian region north of Great Slave lake consists of two well defined physiographic units, a feature first noted by J. T. Wilson (2). The boundary between these lies close to the north shore of the east arm of the lake and extends northwesterly near Spencer, Beniah, Carp, and Ghost lakes (Figure 1). South and west of this line, exposed bed-rock makes up the greater part of the land area; eskers are very rare, and overburden is largely limited to rock-walled valleys and depressions. North and east of the line, outcrops are rare or absent, eskers are abundant, and most of the surface consists of drumlin-like drift hills, elongated parallel to the direction of ice movement (Figure 2). Where this boundary passes through the area shown in Figure 1, it lies near the 1,200-foot contour and may mark the maximum extent of the lake or sea arm present in this vicinity toward the end of the Pleistocene period. For convenience, the first area may be called the 'bed-rock belt' and the other the 'drift belt'.

Jan 1, 1945

By M. S. Badollet

"IntroductionASBESTOS FLOATS may be defined briefly as blends of air-borne particles of fibrous asbestos and dusts produced during the milling stages and collected by Cottrell precipitators, dust sheds, or bag-houses.The various grades of asbestos floats on the market contain fibrous asbestos particles ranging in length from microscopic to approximately 1/4-inch. The fines or dusts present in the floats are from 40 microns to 2 microns or less in cross-section.Airborne asbestos particles are of diverse length because they are collected at numerous places in the mill. There are: (1) dusts removed from dry rock storage bins, (2) dusts removed from rock and fiber screens, (3) particles from the tops of collectors, and (4) fines removed by suction from the processing equipment. Sometimes the airborne particles are kept segregated, so that there is a partial separation by gravity. This is accomplished by a series of dust chambers enclosed in a long, rectangular building. The longest and heaviest particles fall nearest to the air flow entrance, the smallest at a point farthest away and nearest the exit. Sometimes the air from the dust chamber building is passed through a series of bag-houses or electric :precipitators ,to collect the extremely fine particles which normally escape to the atmosphere."

Jan 1, 1952

By George C. Coupland

"THE PRELIMINARY EVALUATION of the orebodies was computerized for tonnages and grades on a 20- by 20-ft grid. The evaluation was based on drill-core intersections over 40-ft vertical projections coinciding with the proposed bench intervals, taking the deviations of the drill holes into account. The computer print-outs gave an ore distribution and evaluation bench by bench and indicated the areas of varying mineralization. The two orebodies have a combined length of 2,200 ft. and a maximum width of 600 ft. They strike almost due north, dip about 85 degrees east and rake to the north. The computer print-outs were used to design an open pit with an over-all waste to ore ratio of 2.58:1. At the outset, the waste to ore ratio was 4:1. The pit is tear-drop shaped, with the narrow end to the south, and at the surface is 2,600 ft long by 1,800 ft wide. Ramps are 100 ft wide, with a 10% grade. The south ramp is left-handed, starts at the southeast and will continue to the bottom of the pit. A second ramp on the west and north walls runs from surface to join the south ramp at 7 bench. This ramp will handle the total pit production when part of the south ramp, from 4 bench to surface, is lost due to the underground operation. Over-all wall slopes are 53 degrees, and are laid out to avoid prominent protuberances which could relax and become unstable and potentially dangerous (Fig. 1) ."

Jan 1, 1974

By Chi Zhang, Junyi Wu

"The use of permanent stainless steel cathodes for electrorefining and electrowinning of cathode copper had been introduced to the market long time ago and now is a well-accepted technology worldwide. During the last decades, the Chinese copper refinery industry had been growing rapidly and many large scaled production plants had been built. In the modern refineries, permanent stainless steel cathodes are introduced and used instead of traditional starter sheets. The most common steel grade used is austenitic stainless steel S31603 (316L/1.4404), while both S30403 (304L/1.4404) and N08904 (904L/1.4539) have been used depending on the actual working conditions, especially with regarding corrosion environment. While 316L permanent cathode functions well in many plants, different kind of problems, such corrosion and deformation, have been reported. There is therefore an increased need for more suitable material. New stainless steels, such as duplex stainless steels, with better properties have been tried and introduced into the application of permanent stainless steel cathode with satisfied results. The article introduces first the Chinese copper refinery industry and properties of duplex stainless steel in general, and then describes the development of using permanent duplex stainless steel cathode, including the actual working conditions, production of cathode sheets as well as the experiences of application in details. After more than one year’s usage, the advantages of permanent duplex stainless steel cathodes are clear seen.INTRODUCTIONChina has become a major player in the international copper market, accounting for around 40 percent of global refined copper demand. Despite the slowdown of the Chinese economy, the consumption of copper products will still increase, but with a medium and/or low growth which will be the new situation for the coming years. The average growth rate is expected to be around 5 percent per annual. In the coming Five-Year plan for National Economic and Social Development a number of initiatives will be finalized which will require massive amounts of copper. In 2015, the expected consumption of copper products will be over 9 million metric tons. The main driver of the consumption is the electric power industry which accounts nearly the half of the total consumption; followed by cooling application with 15% and transportation with nearly 10%, see figure 1."

Jan 1, 2016

By Jochen Petersen, Jean-Paul Franzidis, Allan Nesbitt

This study presents a method for the determination of intra-particle diffusivities in ion-exchange resins for the purposes of evaluating the state of resin degradation during service. The method uses a zero length column (ZLC) in a closed circuit with variable speed pump and reservoir. The intra-particle diffusion is determined from absorption data by using the Nernst-Plank approximation along with the ‘mass transfer factor’ - which is a product of the mass transfer coefficient (kf )and the concentration of the adsorbing ion in the liquid at the surface of the resin - in a computer algorithm fitting simulated curves to experimental data.. Through this approach the changed intra-particle diffusivity, of a gel-type acid resin, over a 1000 loading and elution cycles, is shown.

Jan 1, 2014