Search Documents

"Real time analysis of conveyed bulk materials can be used to improve process performance by reducing variability and upgrading ore quality through selective removal of increments of flow that do not meet appropriate selection criteria. This paper focusses on proven Prompt Gamma Neutron Activation Analysis (PGNAA) and microwave transmission technologies used to representatively measure conveyed ore quality in real time so that meaningful decisions can be made between the mine and mill. This enables the effective removal by bulk diversion of small increments of conveyed flow such as waste, highly deleterious material or sub-economic material from the mill feed. Improved ore quality in plant feed optimises process performance, reduces processing costs and minimises tailings generation. Analysis is unaffected by particle size, dust, layering or segregation, mineralogy and belt speed. Technologies are explained and performance examples given from installations in copper and iron ore. The technology has been used successfully in bulk sorting for over twenty years typically using measured increments of a few minutes. Improvements in technology and calibration performance have resulted in accurate measurements over increments of thirty seconds and below.INTRODUCTION Ore quality variability exists on a number of scales. Block model grades represent a few hundred to many thousands of tonnes. Grade control at the mine occurs on a scale typically down to the size of a haul truck, which may be a few hundred tonnes. Highly variable ore quality is detrimental to process efficiency and effectiveness. Processing waste or low grade ore when higher quality feed is available represents a lost opportunity to generate higher revenues earlier in the operational life. Measuring ore quality accurately over short time increments during conveying enables small increments to be measured and diverted according to their quality. The paper explains the technology and benefits. Neutron irradiation techniques were considered potentially suitable for conveyed bauxite measurement by Beurton et al, 1995. Tran & Evans (2001) concluded there was no equivalent technology to Prompt Gamma Neutron Activation Analysis (PGNAA) in terms of material penetration power. PGNAA was evaluated by Nelson & Riddle (2003) for possible use in the phosphate industry and recommended its use for further characterisation of the mine’s various ore types to improve stockpile allocation and grade control. Cottle (2007) discussed test work for an iron sinter application and Delwig et al (2011) described the successful installation in 2009 and performance of PGNAA for base-to-acid ratio control in sinter feed with the analyser output used to control lime addition. Geoscan (PGNAA) works very well on iron ore and can “improve control over what is happening in the plant” and that comfort can be provided in knowing that the product is on-spec according to Minnett (2010). PGNAA is not yet used in the minerals sector for tariff purposes as has occurred since 2000 with Coalscan (PGNAA) in coal (Minnett, 2010)."

Jan 1, 2017

By D. Vanin

"Conventional single heading track drifting in the hard rock mining industry has not shown any significant improvements in advance rates, despite the advent of modern track jumbos and igh speed muck handling systems .This paper presents Kiena 's experience in using a 7 ft 2 in. diameter larva Mark 6 Tunnel-Boring Machine (TBM) for driving 6000ft of drift.IntroductionKiena Gold Mines is located about 5 miles west of the town of Val d'Or, Quebec, approximately 300 miles north of Montreal. The mine commenced production in October 1981 and has gone through various expansions of ore production with 287 916 metric tonnes in 1982 to reach 453 800 metric tonnes in 1986.Due to the majority of claims being covered by a lake, a grassroots exploration drive of remote areas of the property was required to allow diamond drilling on a yearly basis. High speed sequential excavation methods (SEM) of single heading drifting in the mining industry has not progressed much in the past 20 years despite the advent of electric-hydraulic jumbos, Haggloader and Hagglund type cars. Certain examples of record SEM drifting advances have been performed in the past but only under very specific ground and cost conditions."

Jan 1, 1987

By Fathi Habashi

The year 1987 marked the centennial of the beginning of modern hydrometallurgy. On October 19, 1887 British Patent No. 14174 entitled Process of Obtaining Gold and Silver from Ores was issued*. The discovery was made by John Steward MacArthur (Fig. 1), a chemist-metallurgist, supported and assisted by Robert and William Forrest, two brothers practicing medicine in Glasgow. The discovery was made in the basement of their clinic. The process, which became known as the cyanidation process in reference to the alkali cyanide reagent used, immediately received industrial success in New Zealand in 1889 and in South Africa in 1890t. It displaced the chlorination method which had been in use. In 1903 MacArthur was awarded the first Medal of the Institution of Mining and Metallurgy in London1131 - The cyanidation process was responsible for the doubling of gold production in the world in the two decades which followed its first application (Fig. 2). To the modern metallurgist, it may be surprising to think of MacArthur coming across an obscure reagent such as an alkali cyanide as a leaching agent for gold ores. It is the purpose of this paper to discuss the background and the factors that led to this invention, the development of the understanding of the process, and the application of modern technology.

Jan 1, 1999

By R. A. May, P. J. Brooks, W. M. Smith

"Neill and Gunter Limited (NGL) has prepared a preliminary design and a cost estimate for a ferric chloride leach plant to recover copper, lead, zinc, and silver from a typical complex sulphide ore. This plant design is specifically intended to treat unconcentrated ground ore (flotation feed), but can be readily adapted to treat bulk concentrates. Samples of ground ore and bulk concentrate were obtained from Heath Steele Mines, Miramichi, New Brunswick, laboratory testing, and preliminary process flow sheet preparation was carried out by the Research and Productivity Council in Fredericton, New Brunswick. Approximately thirty drawings have been produced, including process and equipment flowsheets, process piping and instrumentation drawings, and preliminary general arrangements. Preliminary capital and operating cost estimates were prepared for a plant that would treat 1000 t/d of crushed and ground ore to produce about 30 000 tpy of zinc. Capital and operating cost estimates were also projected for plants up to 4000 t/d of processed ore. Recoveries of 99% for zinc, 98% for lead, and 96% for copper were achieved in laboratory tests on unconcentrated ore. These recoveries were higher than the overall recoveries obtained from bulk concentrate, yielding approximately 10% more revenue.A 1000 tonne per day plant was determined to have a low return on investment, however, depending on the size and type of mining operations employed and the FCL plant throughput. DCF-ROI projections of 20% to over 30% were calculated for 100% equity financed “green field” mine, mill and FCL plant operations of 2000 t/d and higher"

Jan 1, 1997

By J. R. Andrews, R. P. Young, J. M. Reyes-Montes

"Microseismic monitoring provides insight into the location and extent of rock-mass fracturing induced by cave mining, enabling interpretation of the cave profile and validation of predictive numerical models. Source location uncertainties can lead to misinterpretation of the inferred characteristics of the fracture network. One principal source of uncertainty is the velocity model used to invert the location algorithm. Large-scale 3D numerical models of modulus changes across a caved mass can represent such complexities in the location algorithms, allowing more accurate interpretation of the microseismic activity. A Northparkes mine case study applies this advanced approach to microseismic data interpretation.RÉSUMÉ Le suivi microsismique fournit des renseignements sur la localisation et l’étendue des fractures de la masse rocheuse induites par l’exploitation par blocs foudroyés; cela permet d’interpréter le profil de la chambre foudroyée et de valider les modèles prédictifs numériques. Les incertitudes quant à la localisation de la source peuvent conduire à des mésinterprétations des caractéristiques inférés du réseau de fractures. Une des principales sources d’incertitudes est le modèle de vitesse utilisé pour inverser l’algorithme de localisation. Des modèles numériques tridimensionnels à grande échelle des changements du module d’élasticité à travers une masse foudroyée peuvent représenter de telles complexités dans les algorithmes de localisation, permettant ainsi une interprétation plus juste de l’activité microsismique. Une étude de cas à la mine Northparkes applique cette approche avancée à l’interprétation des données de microsismicité."

Jan 1, 2016

By D. Roy Eccles

A multi-element geochemical response, with contrasts of up to 29 times background, was obtained in soil above the Mountain Lake Diatreme, northwestern Alberta. The overall geochemical signature is indicative of an ultramafic source; geochemical responses contain elevated concentrations of Co, Cr,O, Cu and Ni with the presence of high Ba, Ga, HI, PO,, Rb, Ta, Ti and light rare earth elements suggestive ofa kimberlite or lamproite body. The shape, or morphology, of the enzyme leach-based geochemical signature over the Mountain Lake Diatreme combines moderately strong to strong oxidation halos, or a rabbit's- ear geochemical profile, with a sharply-defined apical geochemical profile. Because some Alberta diatremes discovered to date form positive topographic highs, the resultant geochemical signature may express the soil development profile that forms directly on top of kimberlitic and lamproitic bodies. The enzyme leach technique, which has proven to be a useful tool in base metal, precious metal and petroleum exploration, may have a significant impact on exploration for kimberlite, lamproite and related rocks in Alberta by providing industry with a useful and cost effective tool to probe blind and/or buried anomalies identified by airborne and ground magnetic surveys in areas of glacial overburden.

Jan 1, 2001

By W. A. Roliff

The renewed interest of the past few years in the Appalachian and Michigan oil provinces has not, as yet, created any marked increase in activity in Southwestern Ontario. During 1960 development drilling in-creased somewhat over 1959, but exploratory drilling decreased slightly. More attention was devoted to the deeper horizons, but lake drilling de-creased considerably. Oil production reached a new peak and gas production increased slightly. During 1960 an interesting oil and gas discovery was made in the Cambrian and gas discoveries six miles off-shore in the eastern part of Lake Erie were made in the Clinton-Cataract zone of the Silurian. This paper reviews activities during 1960, summarizes the discoveries made to-date and the pertinent exploration data relating to the prospects of the region and discusses some of the economic aspects of exploration and development. D URING the last few years there has •been a marked renewal of interest in the old petroleum

Jan 1, 1961

By L. D. van Dyk, G. S. Tshofu

Iron ore fines are by-products of iron ore mining operations. Unlike iron ore lumps, fines cannot directly be used in conventional iron making processes, and consequently large quantities accumulate around the world. Pelletizing and sintering can be used to convert iron ore fines into agglomerates or briquettes for processing with lump ore, but these techniques are energy intensive and produce greenhouse gases. This research investigated the extraction of iron from iron ore fines using acetylacetone (a ß-diketone) as an environmentally friendly alternative process for fines utilization. A 2k factorial experiment design was used to identify the significant extraction variables. It was found that the reaction temperature and solid to liquid ratio had significant effects on the extraction process. The extraction kinetics were studied at different temperatures and the highest iron extraction (97 %) was obtained after 48 hours at 413 K and 0.025:1 (g:mL) solid to liquid ratio for a particle size range of +106 to -150 µm. The extraction products were easily separated from the unreacted acetylacetone by flash distillation and iron(III) acetylacetonate crystals were recovered. An economic evaluation showed that selling the crystals was profitable. Alternatively, the crystals can be reduced with hydrogen to iron particles and acetylacetone (for reuse).

Jan 1, 2015

By R. E. Martin

"The Westerose Leduc (D-3) pool, a Devonian reef reservoir situated in Central Alberta, Canada, has now been producing for over seven years. As a unit operation, the pool pro-vides an interesting example of the full exploitation of gravity segregation tendencies. The reef has a 238-foot oil column, underlain •by bottom water and over-lain by a substantial gas cap. The original hydrocarbons in place were 147.96 million STB oil and 94.4 MMMCF of Taw gas cap gas. Nine-teen producing wells on 80-acre spacing have been completed, most of which are highly productive. Gas injection operations return solution gas to the gas cap. A study of the rock and fluid properties of the pool show it to be conducive to production by gravity segregation at high rates. Monthly average producing rates have varied between 800 B/D and 8,000 B/D and have recently totalled 3,000 BID to 5,000 B /D. Recovery and performance predictions under partial pres-sure maintenance at 10,000 BID indicate an ultimate recovery of 66 per cent of the original oil in place. In the absence of pressure maintenance, recovery would be only slightly less."

Jan 1, 1960

By A. Rodriguez-Prado, P. Kuschk, R. L. Legge, W. C. Lennox

Using constructed wetlands to chemically reduce hexavalent chromium Cr(VI) to Cr(III) from industrial and mining wastewater has proven to be feasible and efficient. Applying first-order kinetics to describe the process is simple, but in some cases a more accurate model is required to reflect the process. This paper studies the feasibility of using non–first-order kinetics to describe the reduction process. Results indicate that half- and second-order kinetics adequately described Cr(VI) reduction in laboratory wetland mesocosms. The organic carbon content played a relevant role, whether it was built up by plant growth or spiked into the feed water.

Jan 1, 2014

By Dwayne D. Tannant

The Adra tunnel near Naramata BC experienced a fire in 2010 that burned timber sets within the tunnel and caused severe spalling of rock from the roof and tunnel walls. The nature of the damage is documented and efforts completed to rehabilitate and open a portion of this tunnel to the public are described. The use of shortcrete and rock bolts is a technically and economically superior support system to timber sets as well as being far more fire resistant.

Jun 1, 2012

By F. J. A. van Ruitenbeek, M. Dalm

In the presented study test work was performed with near-infrared hyperspectral imagery (NIR-HI) on 36 ore samples from a South-American epithermal Au-Ag mine. The aim of the test work was to investigate if NIR-HI provides information about the alteration mineralogy of samples that can be used to predict their economic value. Mineral distribution maps were produced from the hyperspectral images by using correlation coefficients between the image pixels and a set of reference spectra. These maps showed that detection of mineralogy with NIR-HI can be used to distinguish; i) ore particles with low Au and Ag grades, ii) ore particles with high carbon contents, iii) ore particles with high sulphur contents.

Jan 1, 2015

By Gyeonghye Moon, Inhyeok Choi, Jyothi Rajesh Kumar, Jin-Young Lee

"This paper deals with the recovery of the tungsten and vanadium from spent SCR catalyst leach liquors by different hydrometallurgical methods. The first part consists of pressure leaching of spent SCR catalyst using caustic soda followed by metal recovery by liquid-liquid extraction. In a leaching process, the following experimental parameters were tested and optimized: NaOH, particle size of feedstock, temperature, and solid to liquid ratio. The optimum condition for leaching of tungsten and vanadium was under the following conditions: NaOH 3 mol/L, temperature 250°C, particle size <300 µm, and solid to liquid ratio 0.4. From these optimum conditions in this experiment, the dissolution efficiency of vanadium and tungsten was 91.5and 87%, respectively. Liquid-liquid extraction following commercial extractants were tested: TBP, Cyanex 272, D2EHPA, Aliquat 336, Primeme JM-T, Alamine 308, Alamine 304-1, and methyl-tri-octyl-ammonium chloride. The conditions for both valuable metal recoveries were optimized.INTRODUCTIONSelective Catalytic Reduction (SCR) catalyst has become the most effective to reduce nitrogen oxide (NOx) emissions from stationary segments such as power plants and waste incinerations around the world due to the reinforcing regulatory trend and emerging environmental issues (Forzatti, 2001; Spivey, 2002; Li et al., 2011).Currently, the most widely used SCR catalyst is V2O5-WO3/TiO2 system due to its great catalytic properties (Li et al., 2011; Marshneva et al., 1995; Marbergeret al., 2015). In general, the composition of the SCR catalyst used in the stationary application is 0.5 to 1 wt% of V2O5and 7 to 10 wt% of WO3(Marberger et al., 2015; Chen &Yang, 1992, Vuurman et al., 1991; Alemany et al., 1991). Currently spent SCR catalysts are treated as waste and disposed of in landfills. This causes a lot of waste of secondary resources of vanadium and tungsten. In terms of industrial value of vanadium and tungsten (Gupta &Mukherjee, 1990; Moskalyk &Alfantazi, 2003) and reduction of pollutant emissions, it should not be disregarded for their recovery for their material recycling from spent SCR catalyst. However, investigations for recovery of metal values from spent SCR catalyst has been rarely carried out."

Jan 1, 2017

By A. D. Hunt

THIS PAPER will review Canada&apos;s fossil fuel situation as we understand it today and indicate some of the options available to meet our energy requirements during the next 15 years. It would therefore be helpful to examine Canada&apos;s total energy requirements and discuss the un certainties of the data base on which we must base future energy investment decisions. On the world scene, Canada is at the top of the energy-consuming nations, using about 49 bbls of oil equivalent per caput/ year. This appears to be slightly ahead of the U.S. and of course much higher than that of many countries. It is generally accepted that there is a more or less direct relationship between energy consumption and material standard of living. However , as we know, Canada, when compared with other industrialized countries on a GNP, an individual-income or some other standard basis, is lower in the list. This situation may be explained by our more severe climate and a relatively small population distributed over a land mass second only to that of the Soviet Union.

Jan 1, 1977

By Olanrewaju A. Ojo, Xu Wang, Jian Xin Dong, Lina Zhang, Jerzy A. Szpunar

"The influence of crystallographic orientation on the pitting corrosion behavior of Ni-Fe-Cr alloy 028 was studied by a combination of X-ray diffraction (XRD), electron backscatter diffraction (EBSD), potentiodynamic polarization technique and atomic force microscopy (AFM). The results show that there is anisotropy of pitting corrosion that strongly depends on crystallographic orientation of surface planes. The distribution of pits frequency in standard stereographic triangle shows that the crystallographic planes close to {100} are more prone to pitting corrosion compared to planes of {110} and {111}. The calculation of surface energy (001) and (111) shows that the planes of high packing density of atoms have low surface energy with concomitant strong resistance to pitting corrosion. A correlation function between crystallographic orientation and pitting corrosion susceptibility suggests a method not only to predict the pitting resistance of a known textured materials, but also to improve corrosion resistance by controlling materials texture.INTRODUCTIONNickel-iron-chromium(Ni-Fe-Cr) alloys are widely used in various industries and engineering sectors due to their combination of good mechanical properties and high corrosion resistance(Hibner, 2001; Thomas, 2006; Ghosh, 2005).Ni-Fe-Cr alloy 028 (alloy 028)has such important characteristics worth mentioning. Alloy 028 contains high amounts of nickel, copper and molybdenum which improve its resistant to corrosion attack in reducing medium, and presence of high level of chromium makes it more resistant to oxidizing species. Moreover, alloy 028 is less expensive because of higher amount of iron compared to other similar alloys. Currently, alloy 028 is manufactured as evaporator tubes applied in the phosphoric acid production; production tubing and casing used in deep and sour gas wells; heat exchangers employed in nuclear power plants, and seawater-carrying piping and seawater-cooled heat exchangers (Bankiewicz, 2012; Kivisäkk, 2003; Gómez, 2003; Xian, 2012; Bellezze, 2004)"

Jan 1, 2017

By Su-Ping Peng

Three dimensional (3D) seismic exploration has been carried out since the 1980s in the mining district of China, where it has been playing an indispensable role in the high yield and efficiency of coal mining. Unlike oil exploration, this technique uses high density seismic acquisition technology. In recent years, it has focused on wide azimuth 3D seismic acquisition. Evaluation of geometry moved away from depending on folds, azimuth and offset, toward being based upon a focus-ray beam. Conventionally, coalfield 3D seismic interpretation focused on time domain and was based on kinematics information, which is only suitable for less complex geological conditions. To achieve high-resolution processing for the complex topography and structure in coalfields, data processing shifted from poststack to prestack. The means to improve the accuracy of interpretation for complex geological conditions are 1) integration of multiple attributes and multiple disciplines, 2) combination of seismic and geological data, and 3) comprehensive combination of time domain and depth domain data. With the demand for lithological exploration, high-resolution data processing must also take into account the requirements of preserving amplitude in seismic data. Seismic attributes technology, seismic inversion technology, and dynamic tracking interpretation are key techniques in 3D seismic exploration. They greatly improve interpretation accuracy, produce better results in the goaf space description of the coal-bearing strata and coal seam structure, and effectively reduce exploration costs under complicated geological conditions. Therefore, these techniques will be the primary means employed in the future to deal with coalfield complex structure and lithological exploration.

Aug 1, 2013

By George Delorme

"AbstractThe basic intention of this paper is to present, from a practical viewpoint, a thorough outline of all the sound and accepted principles connected with attaining satisfactory rope performance from multi-rope friction winders.In order to emphasize the importance of some aspects of rope maintenance, a limited amount of hoist rope theory has been included, a s it is felt that without this, some of the more critical, but nevertheless practical, aspects would perhaps pass without full appreciation of their individual merit.It is very much appreciated that many of the maintenance topics and practices discussed herein are already being observed with a high degree of skill among those already involved in modern friction winding. The hope is expressed, however, that the paper will be of additional assistance, and of particular help in introducing sound maintenance principles to those who are moving into this field of operation for the first time.Hoist RopesWITH a multi-rope friction winder system, structural upset within the hoist rope's cross section can occur if the ropes slip in the drum treads. This upset will usually appear at either end of the rope at the tangent point of the drum or deflection sheave with the respective conveyance in the normal uppermost position. This slipping action on the drum causes the outer cover of a Full Locked Coil or the strands of a stranded rope to shift, leading to structural upset. The result very often means that the ropes have to be withdrawn from service before completing their maximum service potential.The cause of any rope slipping in its tread can be associated with a discrepancy in tension of that rope between one side of the drum and the other."

Jan 1, 1977

By Descarreaux. Jean

"The Abitibi volcanic belt was sampled along a cross section extending from Matagami to a point east of Rouyn. A few samples were also collected in Louvicourt township, Quebec. The major elements were determined for 344 samples, and rock names were defined using normative minerals. The analytical data were studied by means of variation diagrams. The Abitibi volcanic belt is characterized by rocks belonging to both the tholeiitic and calc-alkaline magmatic series, but they show some differences as compared to some typical reference series, particularly those from Japan. Basalt is the predominant rock type and accounts for 44 per cent of the sampled outcrops. The volcanic rocks are relatively poor in K2O and TiO2. Regionally, the volcanogenic copper-zinc mineralization is associated with the calc-alkaline volcanic sequences. Locally, within such sequences, some types of abnormal deviations from the averages are recognized only in association with the copper-zinc mineralization. The anomalies are ascribed to hydrothermal alteration consisting of the introduction of MgO and removal of N a20; enrichment in K20 is also observed where zinc mineralization predominates. Examples of such anomalous zones show that, in places, this alteration phenomenon can be quite extensive. Petrochemical characteristics can be used as geochemical ore guides in exploration programs."

Jan 1, 1973

By M. Tiedtke, T. Crary, P. MacPhail, M. Ounpuu

"The SGS carbon-in-pulp (CIP) / carbon-in-leach (CIL) model was used to evaluate and optimize the carbon circuit at Alamos Gold’s Young-Davidson Mine. Plants samples (pulp and carbon) were tested in a series of small scale batch experiments to determine rates of gold leaching and adsorption on carbon from a combined flotation concentrate/tailing product. The testwork data, along with existing plant data were then used to model the performance of the existing CIL plant and optimize the circuit to improve performance and overall recovery. The primary purpose of the modelling exercise was to determine the most cost effective way to lower solution losses at the plant. The modelling was also used to learn how the various parameters in the CIL circuit affect solution losses and the gold inventory tied up on the carbon. This resulted in recommendations for minor changes in the CIL flowsheet, which were successfully implemented in the plant. The approach, results and plant changes are presented.INTRODUCTION This paper presents the details from testwork conducted on samples from Alamos Gold’s Young- Davidson gold mine which is located near the town of Matachewan, approximately 60 km west of Kirkland Lake in Northern Ontario, within the southwestern part of the Abitibi Greenstone Belt. The objective of the test program (completed by SGS Canada in 2013) was to investigate and model the combined flotation concentrate / tailing carbon-in-leach (CIL) circuit and suggest ways to improve gold recovery. The metallurgical test program included mineralogy, rheology, and carbon modelling testwork. Plant information was provided during the test program and used in the optimization process. Upon completion of the testwork, plant changes were recommended and implemented at site (October 2014). Plant results from 2014 to 2017 confirmed the modelling results."

Jan 1, 2018

By Philippe Caudal

This paper presents a case study in which a slope failure was observed on the west wall of the LAB Chrysotile mine in the vicinity of the main ramp in January 2010. Airborne LiDAR results were used to evaluate slope geometry before and after the failure occurred. Back analysis of the failure was performed to assess rock mass properties at the slope scale using various numerical techniques: limit equilibrium, finite elements and fracture networks. The various approaches correlated well with field observations.

Aug 1, 2013