Search Documents

The current insurance market has been brought about by a number of pressures, including: collapsing investment returns; growing losses, both normal and catastrophic; and reserve strengthening. This is impacting most classes of insurance coverage, with the traditional characteristics of higher pricing and greater levels of retention, however it is now translating into a lack of capacity and reduced coverage. This presentation will explain how the market has arrived at this situation and will challenge whether this is the traditional insurance cycle or a structural correction. It will also address the anticipated time of correction.

Jan 1, 2003

Underground mines in Australia and worldwide are extending to greater depths. The effect of depth brings a number of challenges to mining engineers including geotechnical, ventilation, haulage and selection of mining method. The main effects of depth from a ventilation perspective are increased heat and humidity leading to reductions in productivity, occupational safety and health issues and the potential for fatalities. Numerous approaches have been undertaken over the years to mitigate against these effects. In this paper a review of various approaches to improving climatic conditions at a number of mine sites worldwide is undertaken. From these case studies it is argued that for mines at depth with the potential for a climate problem perhaps an alternative design philosophy to the established design philosophy should be utilised. In conclusion, the paper proposes some simple rules of thumb for use in mines with climate problems or the potential for climate problems.

Jan 1, 2008

Although geophysical methods of prospecting have proved indispensable in the search or oil deposits elsewhere; it is only 'in recent years that they have been used to any significant extent in Australia. The increase in their use has been quite remarkable over the past two or three years, due in Sao small measure to the encouragement given by means of Commonwealth subsidy. There is no doubt that the use of' geophysical methods will coxi-tinue to increase and this increase could be greatly accelerated as and when oil is discovered in commercial quantities,This review of their use A in Australia and the remarks and statistics are confined to work on the mainland. There has been, a substantial amount of geophysical work in Papua, but as operating conditions are so very different to the mainland Papua has been regarded as a separate province.

Jan 1, 1962

By Tyler MA

If the record of maj or proj ects in Australia is taken into account, it is apparent, the proper planning of an industrial relations strategy for many such projects has been ill considered by project developers. The recognition of the need to develop a plan from the initial feasibility study has been forced on those promoting new projects by the publicity given to the Australian industrial relations record. The delays in delivery caused by factors supposedly out of the project's control are often given for non-performance of contract and used as an excuse for limiting further development. Many of the problems experienced in project development can be overcome with sound industrial relations planning. The promises given in the euphoria of the early stages of a project relating to price and delivery often become a burden for the future because the complexities of the Australian Industrial Relations Systems are not understood or considered. The recognition by senior executives of their responsibilities in this area will contribute greatly to a new era of project development.

Jan 1, 1983

By Westcott PC

The development of a coal project must pass through a number of phases, taking it from a preliminary evaluation through to detailed mine planning. For each phase the cost of data acquisition and associated mining studies increases exponentially for linear improvement in confidence levels. Within each mine planning phase there are four main activities. These are the economic ordering of reserves, the development of optimum mining strategies, mine design and scheduling and finally the estimation and analysis of costs. The development of the optimum mining strategy is one of the most critical aspects of a mining evaluation and the application of economic criteria at this stage of the project is vital to the successful generation of an optimised mine design. A recommended method is the concept of Economic Ratio (ER) which expresses the likely cost of mining from a given location in a deposit in terms of the value of the product likely to be recovered. The most economic mining strategy will be to mine areas from low economic ratio to high economic ratio within the constraints of reasonable equipment application. When selecting equipment a particular machine should not be selected solely on comparison with other machines in isolation, but the total application must be analysed. In the final selection the decision should be based on whether or not it has a beneficial effect on overall project economics. The economic assessment must take into account the time value of money, so the real cost can be determined with adequate provision for capital and operating costs over different time spans.

Jan 1, 1983

By S R. Grano, M Vera

This paper deals with two separate case studies investigating the froth phase performance and characterisation of two industrial rougher/ scavenger flotation circuits. Froth phase performance was quantified using a mass balance approach to estimate froth zone recovery. Measured characteristics of the froth phase included frother solution concentration determined by gas chromatography, and the time taken for an equilibrium froth sample to decay to one-half of its original froth height. The latter measurement is referred to as the æfroth half-lifeÆ and is strongly linked to froth stability. Special methods and techniques developed to preserve frother in solution and to measure froth half-life are briefly described. The frother type in the first case study was a mixture of straight and branched alcohols, whilst the frother type in the second case study was a mixture of alcohols, aldehydes and triethoxybutane. The first case study focussed on a flotation circuit treating a low-grade ore containing only a small fraction of floatable copper sulfide minerals, while the second case study focussed on a flotation circuit treating a higher grade complex sulfide ore containing significant quantities of chalcopyrite, galena, sphalerite and pyrite. It was found that froth zone recovery of valuable mineral generally decreased down-the-bank of the two industrial rougher/scavenger circuits. Moreover, decreases in froth zone recovery significantly limit the overall cell recovery of valuable mineral achievable from the plant scavenger cells. However, the decrease in froth zone recovery could not be linked to the removal of frother from the pulp solution to the concentrate product in the preceding rougher flotation stages. Measurements of residual frother in solution suggested that, approximately, only five to ten per cent of the added frother was removed into the rougher/scavenger concentrate, with the remainder appearing in the scavenger tailings. This finding suggested there was apparently adequate frother in solution in the scavenger stages.

Jan 1, 2005

By Somasundaran P

Controlled modification of mineral/liquid interfacial properties by adsorption is critical for mineral processing operations such as flotation, filtration, dispersion and flocculation. Ionic/nonionic surfactant mixtures usually show enhanced surface activity and salt tolerance over ionic surfactants, and this is especially beneficial for flotation of salt type minerals in which case dissolved multivalent cations in high concentrations usually cause loss of anionic surfactants by precipitation. Adsorption of nonionic/anionic surfactant mixtures on kaolinite has been studied with sodium dodecylsulfate as the anionic surfactant and octaethyleneglycol mono-n-dodecylether as the nonionic surfactant. Synergistic interaction between these surfactants was found to cause adsorption of the nonionic surfactant with its hydrophilic chains protruding into the bulk, leading to substantial changes in flotability and dispersion characteristics of kaolinite. Similarly, hydrophobicity changes are observed also' for silica particles upon adsorption of nonionic ethoxylated alcohols owing to possible changes in the orientation of the adsorbed surfactant species at the interface. Also, based on the results obtained with surfactant adsorption, a hydrophobically modified polymer was used successfully to disperse graphite particles in aqueous solution.

Jan 1, 1993

This paper critically reviews the role of institutional research contractors (eg universities and the CSIRO) in the delivery of effective research, development and demonstration outcomes in mineral and coal processing to the Australian mineral industry. The criteria by which such R&D is justified, and the problems of quantifying the benefits of such research, are considered. Third-party funding mechanisms such as NERDDP and AMIRA are reviewed in the context of the difficulty of setting national research priorities. Some case studies are presented which illustrate both the problems and the advantages of institutional research for industry. The transfer of research outcomes to industry is identified as a significant problem which limits the effectiveness of all institutional research. Other topics reviewed include research management, the relationship between industrial companies and their research contractors, and the real costs of research. The paper offers suggestions for the ingredients needed for a successful industry-institution relationship, based on the Australian experience. It is concluded that the Australian model for this relationship is a very effective one, although there is still room for improvement.

Jan 1, 1992

Hindered settling devices (teeter bed, up-current) are widely used in the mining industry to classify mineral streams into various size fractions and to separate minerals. In the coal industry these devices are extremely successful in separating coal of low densities from shale and pyrite. In the beach sand and in the iron ore industry, this equipment is used to beneficiate minerals either as stand alone units or lately as classifiers in spiral circuits. The challenge that these applications give to metallurgists is to be able to simulate the equipment by using mathematical models with or without the aid of small bench scale tests. In any green fields and many brownfields projects, limited amounts of samples make pilot plant tests difficult. Although there are mathematical approaches available, the accuracy is of such a nature that it can not be used for design purposes. This refers to the use of StrokeÆs law, NewtonÆs and the so called intermediate law as is widely published. Research done by the author indicates that in most applications none of the above laws apply. Using the original data as published by Perry and Chilton (Chemical Engineering Handbook, pp 5-64, 1973) and re-plotting it indicates that the settling velocity of particles is a function of (particle diameter)n where n varies between 1.2 and 1.6 which is different from that predicted by the intermediate law that suggests that n = 1.18. Another way of describing the relationship between the drag force and the Reynolds number is done by iterating between settling velocity and the Reynolds number. This needs more computer time but the accuracy obtained from this does add value to simulations. A small but simple test is suggested to determine the settling velocity of particles to enable metallurgists to determine variations from the theoretical calculations to determine the influence of viscosity and particle shape.

Jan 1, 2008

Mining companies around the world devote considerable effort to production reconciliation and metallurgical accounting. However, although sampling, weighing and analysis methods used to obtain the raw data for metal balancing continue to improve, they are still areas that are sadly neglected. Using the latest metallurgical accounting package to improve metal balancing is fundamentally flawed if the data used are unreliable in the first place. The basic rule for correct sampling is that all parts of the material being sampled must have an equal probability of being collected and becoming part of the final sample for analysis. If this rule is not respected, sampling bias can easily be introduced. Unlike precision, which can be improved by replication, bias cannot be reduced once it is present. Sampling and sample processing procedures must therefore be carefully designed both to minimise bias and to obtain acceptable precision. The most suitable sampling location is the discharge point of a process stream, where increments can be obtained by taking a complete cross-section of the stream with a sample cutter. Sampling devices that take only part of the stream may introduce serious bias and must be avoided. The moisture content and wet mass of the material being sampled are of similar importance to chemical analyses for determining metal content. The accurate determination of moisture content is particularly difficult, because the moisture content of samples can change after the sample is taken, eg due to moisture evaporation. Hence, moisture samples need to be taken quickly and placed in sealed bags or containers that are impervious to moisture. The moisture content should then be determined without delay. To determine wet mass, a range of weighing methods are used in industry, including weighbins, weighbridges, conveyor weightometers and platform scales. The precision and accuracy of these methods vary considerably, so it is important to select a method with the appropriate precision and ensure that the weighscale is well maintained and regularly calibrated.

Jan 1, 2002

Bauxitic laterite of variable thickness and grade is best developed in the Darling Range but covers a large part of the southwest corner of Western Australia. Its limits are defined by the rainfall isohyets to which jarrah forest is confined. Within this broad belt there is an increase in arable land southwards concomitant with a thinning of the laterite layer.Bauxite quality and perhaps thickness as well are dependent on the type of source rock, and are influenced by topography. Economic deposits occur over a vertical range in altitude of about 1200 ft. Some bauxite orebodies appear shoot-like in character, and analogy is suggested with the ore shoots of syngenetic metalliferous deposits.The alumina is in the form of gibbsite enabling low temperature digestion in treatment.INTRODUCTIONAlthough the existence of bauxite in Australia has been known for many years it is only recently that exploitation has commenced of the two most important deposits, strangely at almost diagonally opposite tips of the continent (Fig. 1).Recognition of the importance of the bauxite in the southwest corner came about initially through the efforts of Western Aluminium N.L. which, with some outside financial help, tackled the early exploration with commendable foresight and courage. Subsequent investigations around the periphery of the original reserves (now held by Alcoa of Australia) were undertaken by several companies, including Bauxite Exploration Pty. Ltd.ORIGIN OF BAUXITEThe genesis of bauxite is stilI somewhat controversial.Owing to its common association with kaolin some investigators have been led to believe that it has been derived from the latter; others believe the process has been vice versa.From a recent study of the Arkansas bauxite region in the...

Jan 1, 1964

A study of the effect of nickel on the cupellation process has shown that a very low "nickel limit" must be imposed for cupellation (0·08 grams nickel or 0·05 grams when copper is present). In the presence of slightly greater amounts of nickel, lead tends to spreadon the cupel with detachment of drops from the main lead pool. In crucible fusions nickel contaminates the lead button to a small extent, and this contamination is increased.in the presence of either iron or copper. Nickel also causes "shotting" of the lead, this effect being more apparent in the presence of iron.Both the spreading during cupellation and the shotting during crucible fusion are considered to be caused by adsorption of insoluble NiO at the Pb-PbO interface, lowering the interfacial tension.Excess litharge crucible charges are' fused at 116boC. to eliminate shotting. A brief· soaking in molten basic litharge slag effectively reduces the nickel content of lead buttons. The solubility of silver in litharge slags is considerably decreased in the presence of nickel. Corrections can be applied for silver losses in slags but these corrections are not as accurate as with copper ores.INTRODUCTIONThis paper on the effects of nickel on fire assays for silver is the second of an intended series describing investigations into the fire assaying method.In the first paper, discussing the effect of copper on fire assaying processes (Guerin, 1957), it was shown that certain elements, because of their relatively low affinities for oxygen, will tend to contaminate the lead button during crucible fusion and scorification. Nickel, having a slightly greater affinity for oxygen than has lead, would be expected to be oxidized and slagged readily, and would not be expected to appear in the metal phase (lead button) to any appreciable extent. Thus, judged solely on this basis of...

Jan 1, 1960

By Luck D

Current methods of mucking out small development tunnels are a major limitation to improved efficiency and high rates of advance. This is particularly true in the deep metalliferous mines of South Africa, where the harsh environment, remoteness of operations and the hard abrasive rock conditions mitigate against the use of the tunnel borer type of equipment. The Loader Distributor Train was designed to overcome the special problems of hard rock tunnelling. It combines advanced innovative technology with proven simple methods of operation and maintenance. The system aims at taking advantage of new, efficient and cost effective power sources in South African mines based on replacing compressed air with electro hydraulics and the new concept of hydropower. It also introduces electronics and computer technology, for both automatic control and fault finding, into the production environment. The system is designed to permit sophisticated equipment to be operated and maintained by a semi skilled labour force. Although still undergoing trials it is believed that the Loader Distributor Train will prove highly effective, and that the new concepts offer considerable potential in areas other than flat tunnels, in particular the cleaning of inclined shafts.

Jan 1, 1986

Activity-composition-temperature relations for both gold and nickel have been determined for the solid and liquid states of the gold-nickel system by the application of the Margules equations. These relations are in satisfactory agreement with activity measurements of nickel in the solid state, the observed phase boundaries of the system between 700 and 1725°K, as well as being consistent with data on the enthalpy of mixing.

Jan 1, 1971

By J de Vries

Arthur Page, a past President of AT&T said:All businesses in a democratic society begin with public permission, and exist by public approval. Product stewardship in its most basic form is simply risk management applied to the products we produce. Conceptually it may be considered as a more expansive approach to many existing safety, heath and environmental programs. Key differences include the extension of responsibility beyond the direct control of management, and consideration of the implications your products and processes have on the broader community, as opposed to the confines of an individual mine site or operation. This paper reviews the processes used by Orica Ltd to manage its product stewardship program. OricaÆs product stewardship program is expansive and supports activities and business that range from manufacture and delivery of commercial explosives and sodium cyanide to mines throughout the world, supply and operation of municipal water facilities, and manufacture and distribution of consumer products such as household paints and adhesives. We highlight the development of the program through experience both good and bad, and by use of case studies to illustrate how an active product stewardship program is an effective business risk mitigation strategy.

Jan 1, 2006

By Henley S

The year 2000 is not very far ahead - only five years. It should not be hard to forecast what will happen between now and then, because the technologies that will be in practical use then should all be at least in embryo existence now. There has been a historical trend for the mining industry to work ever more difficult and ever more marginal deposits. There are clearly a few exceptions and major discoveries, but the industry is becoming heavily dependent, at both the exploration and the mining stages, on technological innovation to retain acceptable profit margins. With the new exploration and mining technologies come requirements for additional computing support. Computing technology further allows the potential integration of a wide variety of different types of data to help the explorationist to build and test exploration strategies, or to help the miner to design and schedule mining operations.

Jan 1, 1995

By M W. I Visser Æt Hooft, R C. Schimmel

Until recently the Corus IJmuiden pellet plant produced approximately 4.5 Mtpa of pellets. Corus IJmuiden is currently running a program to increase its pig iron production to 6.4 million tonnes HM per annum. The burden of the Corus IJmuiden blast furnaces consists of approximately 50 per cent high basicity sinter and 50 per cent acid pellets, both produced in-house. To accommodate the increased pig iron production, the capacity of the pellet plant needed to be increased to 5.0 Mtpa. The productivity was increased by modifications to the plant layout, which were implemented during the 2006 cold maintenance stop. In addition, the composition of the ore blends is optimised to gain productivity.

Jan 1, 2007

By Coulter K. W

The commercial evaluation of coking coal from bore core data will begin with a technical evaluation of the coal properties affecting coke quality. Methods currently used for prediction of coke.properties from coal analysis are illustrated but in each case accuracy of measurement and prediction should be clearly understood. It is suggested that coal be initially valued from coking properties (base value) and adjusted for chemical properties (merit value). Final evaluation of coal can only take place as coke in the blast furnace where the coke is assessed under high temperature operating conditions. The commercial value of a particular coking coal will depend on many additional factors other than the technical properties.

Jan 1, 1977

A short study showing how first dry fill and later hydraulic sand fill has allowed mining to continue immediately adjacent to worked out areas in a mine 75 years old. This paper is a case study of filling in an old mine where for 30 years filling was not important until ground troubles were experienced after a series of parallel shrink stopes were pulled empty., Dry fill was distributed from the surface via a system of passes and conveyor belts. With the stabilization of the ground it then became possible to continue mining beside and above the old stopes using totally sealed and decanted hydraulic sand fill. A brief description of the dry fill is given and then more technical details of the hydraulic fill. The necessity for a well trained and experienced hydraulic fill crew is discussed along with the problems of filling small stopes in broken ground.

Jan 1, 1973

By Towsey C. A

Significant advances in regional geochemical exploration techniques have been made over the last 5 years in the search for gold deposits. This has occurred largely by the development of the bulk cyanide ex- tractable gold (BLEG) also known as the Bulk Cyanide Leach (BCL) tech- nique. The technique has been developed and designed for Australian conditions and has two main ad- vantages over the pan concentrate technique preferred by many ex- plorationalists, viz:,. 1. It is designed to collect ultra fine gold common to epithermal and other north Queensland types of gold deposits. 2. The large sample (approx.5 kg) allows very low detection levels, ranging between 0.1 and 0.05 ppb Au. The use of the BLEG technique in exploration has led to the discovery of the Wirralie gold deposit and numerous other epithermal gold prospects previously undetected by pan concentrate and minus 80 mesh (pathfinder elements) surveys in the Drummond Basin.

Jan 1, 1989