Search Documents

This paper will describe the exploration project which led to the discovery of the La Escondida porphyry copper deposit in northern Chile and will serve as companion paper to the description of the geology of Escondida being presented by J M Ojeda. The author would like to express his appreciation to Robert Hickman, Chairman of Minera Escondida, for permission to present this paper.In July 1978, a proposal was made by J D Lowell to Robert Wheaton, then Exploration Manager of Utah International, that Utah fund a "grass roots" program exploring for porphyry copper deposits in northern Chile. Wheaton expressed interest, and it was agreed that Getty Oil Co also be invited to participate. A joint venture agreement for the Atacama Exploration Project was signed January 1, 1979, between Utah, Getty and Lowell. The project was managed by Lowell who reported to a management committee which through most of the project consisted of Lowell, Francisco Ortiz, Robert Wheaton, Maurice Young, Sigfried Muessig and Louis Rove. Oliver Warin and Jim Bratt participated in the committee in the last phase of the contract. Special thanks are due Louis Rove of Getty and Maurice Young of Utah who made contributions throughout the course of the project. Francisco Ortiz was resident manager through most of the project.

Jan 1, 1990

The importance of proper planning, preparation, and execution of a steady state sampling campaign for metallurgical plant assessment must not be underestimated. Careful planning can increase the amount and reliability of information from an optimum number of samples and fully utilize available plant data. It requires specification of the data required, determination of run duration sampling frequency, the selection, modification and testing of sample points and cutters, as well as organisation and briefing of plant and sampling personnel. Preparation immediately prior to sampling, the conduct of the sampling campaign itself and procedures to handle the collected samples and information are discussed. Cutter design, fabrication and use are described in detail, and typical sampling situations, for ball mills, classifiers, pipes, launders, flotation cells and thickeners are considered individually. Measurement of pulp flow rate can often resolve difficult mass balance problems, and discussion of convenient techniques is included.

Jan 1, 1976

Australia, with its fast-growing economy and high standard of a~ living, has a high and rapidly increasing per capita consumption of energyIn total terms, Australia's energy requirements are doubling every 15 years, and among mature Western economies Australia ranks behind only Italy-and Japan in the rate of increase of energy consumption.The use of energy is often accepted as a yardstick of development and on this basis Australia might well congratulate itself on its high energy consumption. However, it is less well recognised that the resources absorbed in the production of energy represent a real cost to the* community, and that just as we strive for industrial efficiency or farm productivity we should strive for economy in the use of energy fuels.Australians spend annually an estimated ú500 million.on all forms of energy, a sum which represents about seven per cent of the Gross National Product. In all, energy production and distribution absorb the employment of more than 100,000 persons. In addition, the annual capital investment by.the oil industry amounts to some E55 millions, by the coal industry about ú12 millions, and by electrical and gas authorities some E108 millions, in total representing more than ten per cent of annual investment in other than private motor cars and housing,

Jan 1, 1962

The problem of spontaneous combustion has long exercised the minds of Mining Engineers. The idea of inertising an area with a non combustible gas has seemed to be an attractive way to overcome the problem. Various agents have been tried but nitrogen has particular attractions and advantages. Britain adopted the idea from the German industry and found that it was particularly suitable for the conditions in British Mines. Over 8 years much development work has been done and specialist equipment has been developed as the requirements came to be better identified with experience. There is a continuing programme of innovation and the technique can be further developed in the future as a means of protecting the very heavy investments which are being made in today's large capacity, heavily capitalised faces.

Jan 1, 1988

By T Perera, B Fan, S Thang, T Hsia

Minerals are valuable resources and critical elements for a broad range of biological and technological applications, including technological developments to improve energy efficiency and the global movement to promote a low-carbon economy. However, in order to extract these critical metals, large amounts of waste and toxic chemicals are generated, as well as the use of high energy and large amounts of water consumption. Froth flotation is one of the most commonly used processes to separate and collect high-value minerals, but it still has some limitations, including low flotation efficiency performances using existing collectors and other reagents. Therefore, there is an urgent need to design and develop new metal-specific collectors to more efficiently separate and recover valuable minerals and to allow bulk water recovery from flocculated tailings. In this research, we propose to use our newly designed and synthesised novel collectors derived from a type of vitamin E (α-tocopherol), a relatively inexpensive and non-toxic natural molecule. As a potential collector-building block, α-tocopherol has a long hydrophobic carbon chain that facilitates the attachment to air bubbles during the froth flotation process. In addition, the phenol group of this molecule can be easily modified to incorporate various functional groups for targeting different types of minerals. Furthermore, α-tocopherol can be converted into a monomer for polymerisation by the reversible addition-fragmentation chain-transfer (RAFT) process, which can provide us with polymer based-collectors with high precision control of molecular weight and architecture. So far, small-scale qualitative experiments on α-tocopherol-based collectors have been performed with good results, which indicates the feasibility of these compounds as novel collectors for improved froth flotation processes.

Aug 24, 2022

By Griffiths J. B

From its mining lease at the northern end of Cohens Reef at Walhalla in the North Gippsland Mountains, the Long Tunnel Extended Gold Mining Company produced 13,695 kg of gold, which at 1980 prices represents a value significantly in excess of $200 million. In the period 1885 to 1908 the mine was one of Australia's principal reef gold producers, being top Victorian producer in six of these twenty-four years. Prior and subsequent occupants of the lease produced an additional 160 kg of gold. The Extended and the other mines on Cohens Reef whilst contributing importantly to the financial resource of Victoria, were the sole important support for the substantial town of Walhalla that had grown up around them. When the mines closed, Walhalla gradually reduced from a bustling developed town to the present attractive mountain village so favoured by tuurriSts. To allow the visitor to obtain a better ;ri.icrstanding of Walhalla's mining past, important parts of the Long Tunnel Extended Gold Mine workings and site are being

Jan 1, 1981

By Newman H. A

Goldsworthy Mining Limited is currently mining iron ore at an annual rate of 7 million tons from several small orebodies, each of which exhibit wide variations in iron, phosphorus, silica and alumina contents. Each orebody is mined at its average ore reserve grade and therefore mine planning and grade control techniques have had to be tailored to achieve a constant production blend.

Jan 1, 1973

Three transient phenomena have been observed and experienced in the operation of large solvent extraction mixer-settlers. These relate to the ability of the settler to discharge streams with low entrainments arising from different phase separation æproblemsÆ. The operation of large-scale laboratory and commercial solvent extraction settlers has been shown by a number of workers to be a dynamic process, especially at the feed end. Circulating flow patterns are common in all three organic, aqueous and emulsion phases. The circulating patterns in deep dispersion bands in long settlers are believed to form roll fronts that can travel down the settler length within the bounds of the dispersion band. Various physical models are proposed to illustrate the formation and movement of roll fronts within the dispersion band. Another transient phenomenon has been observed in commercial settlers operating without any dispersion band. Entrainment of the continuous phase in the advancing dispersed phase is at high and erratic levels. This supports the conventional separation model, which recommends the presence of a significant depth of dispersion band to æfilterÆ the secondary haze from the bulk separated phases. The third transient is the position and shape of the dispersion band within the settler. Large commercial settlers have been shown to exhibit high variability in both these aspects of the dispersion band. The elimination of all three transient phenomena in commercial settlers has been shown to be effective with an in-settler media of coarse size and moderate specific surface area. The effect of the media is two-fold: it dissipates both the circulating flows and the forward velocity of any roll fronts, and creates a stable deep dispersion band at the feed end that serves to trap secondary haze from the primary coalescence process. It is effective in treating both types of transients involving non-existent or excessive dispersion band depths. The media serves to enhance coalescence by providing a static surface of intermediate surface tension on which droplets can collapse. The random nature of the media also provides multiple stream splitting and re-combination, that presents further drop to drop and drop to media impingement, which in turn promotes coalescence.

Jan 1, 2000

In October 1993 it was decided to undertake the fourth phase of mining at Big Bell. This decision followed the exhaustion of open pit reserves in January 1993. Two stages of mining were proposed for the new underground mine. The initial stage would mine the remnant ore, consisting of the rib and crown pillars and lower grade ore on the hangingwall and footwall side of the old open stopes, which were mined from the 1930s to 1950s. Most of the old open stopes were backfilled with either deslimed mill tailings or development mullock, both of which were economic to recover. However, the mineable ore from this resource was difficult to evaluate. The second stage focused on mining ore outside the remnant areas and was initially proposed as a Core and Shell method under a caving hangingwall. This method has since been superseded with sublevel caving, in part due to the very high and deviatoric stress conditions encountered at Big Bell and the relatively long mining cycle required for open stoping. The problems and challenges discussed in this paper will cover the identification of remnant ore reserves, dewatering the old workings, and remnant mining.

Jan 1, 1998

Strata bolting/dowelling reinforcement techniques are being reintroduced into the mines of the National Coal Board. There are strong reasons for the selection of the full hole anchorage principle of bolting and for the development of the wood/resin dowel. There are strong reasons also for the measurement of strata bed separation as the method of assessing the effectiveness of a roof bolting system. There are several designs of bolts. Instruments have been developed for investigation and control purposes. Different drilling and bolting machines have been employed in trial sites. In addition comparative laboratory model work has been conducted on simple non-bolted and bolted systems.

Jan 1, 1971

By Donchak P. J, Champion D. C, Fordham B. G, Domagala J

The Hodgkinson Province forms the northern part of the Tasman Orogen and contains the most extensive outcrops of Silurian - Devonian rocks in Queensland. Deep-water, marine siliciclastic sequences (mainly turbidites) dominate most of the province except near the western margin where mafic volcanics and fossiliferous limestones characterise much of the succession. It is difficult to apply normal stratigraphic mapping techniques to the Hodgkinson Province because of extensive stratal disruption by numerous thrust faults, the general lack of stratigraphic and structural markers, and the unfossiliferous nature of much of the succession. Nevertheless, several distinct units have been delineated although their internal stratigraphy or boundary or superpositional relationships are uncertain. Ordovician strata, as well as two major unconformities have been recognised in the western part of the province. Several models have been proposed to explain the evolution of the Hodgkinson Province. Although there is no general agreement most recent researchers favour an extensional tectonic regime.

Jan 1, 1990

Pyrite is a significant gangue sulphide mineral in the Ok Tedi copper ore. Its presence in the flotation concentrate is not entirely desirable since it lowers the grade of the final copper concentrate. Lime depression of the pyrite has been practiced with some success. However, it has been observed that at the pH for pyrite depression a significant amount of the pyrite particles still float. To obtain further insight into the problem this work has been conducted to determine the composition, natural floatability and xanthate flotation behaviour of the various types of pyrite in the ore. The flotation results show that while some types of pyrite float well at high pH values, others are readily depressed. The implications of these results for Ok Tedi flotation plant have been Considered.

Jan 1, 1997

Two ends of a longwall face are not only concentrated locations of equipment, but also provide ventilation and access. The roof strata stability here has an important influence on mining coal and safety. Based on field obser- vations in the gateways at Zaozhuang Colliery (Shandong Province) and model tests, the author developed a structural model of the overlying strata at the ends of the longwall face - the arc triangular cantilever plate - to which the elastic theory of plates can be applied. Factors influencing the stability of the cantilever plate and its breaking character- istics are discussed. Requirements and design parameters for supports at face ends are pro- posed, based on these factors.

Jan 1, 1986

The key elements required to maintain final wall integrity and hence slope reliability are discussed. Failure modes and mechanisms in highly structured rock slopes are then reviewed. The impact of blast disturbance on rock masses in general is discussed and the relationships between the slope failure mode and blast disturbance is then explored. The question of how designers can incorporate such impacts into the slope design process is then addressed. This necessarily involves rock mass strength consideration and two case studies are used to demonstrate a recent dilemma in this regard. Some progress regarding this dilemma has also been reported for the second case study. The major conclusions are that: Slope reliability can be severely compromised if the slopes are damaged by blasting and this impact is not often incorporated into the slope design process. The location and extent of the blast damage will impact some slope failure geometries and failure mechanisms more than others. The concept of failure mechanism specific vulnerability needs to be further developed. The evidence indicates that this aspect is even more extreme for weak ground conditions. The quantification of the reduction in rock mass strength due to blast damage is not well understood and limitations exist with some recent guidelines. The use of the Hoek-Brown criterion for slopes in blocky rock masses requires considerable judgement. Further applied developments in this regard would be very beneficial to the industry. Some promising methods to incorporate blast damage estimates into the slope design process are emerging. It is good business to minimise final wall blast damage otherwise a whole range of issues relating to reduced slope reliability emerge.

Jan 1, 1999

By Wharton P, Voigt R

In order to do the discharge estimation better, it is valuable to find out appropriate formulas for estimating discharge in various pits, based on accumulating data, summarizing discharge patterns applying optimum seeking method and principle, by seeking redical exponent with help of the method of exhaustion, as well as testing and making statistics, in accordance with the quality standards established by our practical experience.

Jan 1, 1988

By K Kuganathan

This paper describes a new methodology that can be applied to compare several bench extraction strategies requiring backfill. The method is applicable at the planning or operational stages and can be used to maintain dilution within design parameters and improve the overall economics of bench stoping operations. The parameters influencing bench performance have been empirically rated based on economical, geomechanical, operational and backfill properties. Four different extraction strategies have been considered and rated from most preferred to less preferred using an integrated approach to bench extraction.

Jan 1, 1998

By W Stange

Assessing the risks in a mining project is a key aspect of project evaluation. This is an exacting and demanding task because of the complexity due to the need to deal with uncertainty over long time periods. The way risks are assessed and managed is critical to the long-term success of the projects and the business. Discounted cash flow (DCF) analysis is commonly used for project and risk evaluation. A discount rate is selected that accounts for uncertainties in the cash flows. However, it is difficult to determine an appropriate discount rate due to the large number of factors that need to be considered and the complex relationships between risk sources. Using a proven framework, ævalue at riskÆ (VaR), this paper proposes to rigorously model and quantify ærisk at sourceÆ. The approach was first employed to assess financial market risks and is now widely used in the banking sector for risk assessment. In project evaluation, all risk sources are identified and estimated separately to ensure the overall project risk is quantified accurately. A bottom-up approach has been proposed. Estimates are first carried out for risk factors at the bottom of the project structure. The assessment is then applied at increasingly higher levels until the overall project risk is estimated. Value at risk is a versatile methodology and can be used in a local or integrated manner. The final value is objective and the calculation steps can be easily justified and followed. Four case studies have been included to illustrate how the proposed approach can assist management in decision-making.

Jan 1, 2009

By Bhattacharyya A. K

The current methods for predicting pillar strengths are reviewed. A two-dimensional model, based on the Mohr-Coulomb failure criterion, is proposed for determining the compressive strength across the width of a long pillar. The model can be used to determine pillar strength and the depth of the crushed (ie yielding) zone from the pillar edges. The values of the parameters in the model, namely the cohesion and internal friction angle of the coal seam, friction angles at the contact of the coal seam with the roof and floor are determined by matching the strengths predicted by this model with the Bieniawski pillar strength formula for pillar width to height ratios up to 5. It is found that the derived values of these parameters are quite close to the results from laboratory tests. Based on the model, a preliminary analysis of pillar stability is made.

Jan 1, 1995

Before commencing design of a coal prepar ation plant, it is essential to have detailed information of the raw coal to be treated to- gether with a clear understanding of the products required. Prediction of raw coal size distribution, particularly the amount of fine material, is difficult and the methods employed should be large scale pilot plant studies or techniques to simulate coal degradation and shale breakdown in water. A detailed knowledge of well proven coal preparation processes and new developments allows processes and process combinations to be compared to'obtain the maximum economic recovery when using lower cost, less efficient processes within acceptable limits. Equipment should be selected bearing in mind its precise application and the location where it is installed. Plant layout should be carefully studied to minimise equipment requirements and to simplify construction. Measurement, control and automation should be an integral part of plant design in order to obtain the optimum performance of the processing equipment.

Jan 1, 1974

By J Rowland, B Belle, M Webber

The Australian underground coal industry has experienced substantial improvements in longwall productivity and, as such, the methods of providing a safe and productive mine environment have needed to evolve and develop. Whilst the primary method of controlling atmospheric conditions is by airflow it has become impracticable or impossible for the majority of Australian longwall mines to contend with all environmental hazards with primary ventilation alone.If the ventilation circuit cannot provide a safe and productive mine environment at an acceptable cost and circuit duty then supplementary controls are required. Examples include pre-gas drainage, post-gas drainage, gas utilisation, refrigeration and innovative dust control systems. Of the 21 longwall operations surveyed in Australia, there were 13 in New South Wales and eight in Queensland.This study represents a timely opportunity for the industry to examine the primary and supplementary ventilation systems implemented in Australian longwall mines and to discuss how to equip the industry to successfully face the future of underground longwall ventilation management in Australia.CITATION:Webber, M, Belle, B and Rowland, J, 2017. Australian longwall ventilation systems, in Proceedings Australian Mine Vent Conference 2017, pp 301–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017