Search Documents

Underlain by and intruded into the sedimentary rocks of the Transvaal Supergroup the Bushveld Complex is the largest known layered intrusion in the world and contains one of the richest ore deposits on earth. It has been the world's major source of Platinum Group Metals (PGM) since the mid-1900s with Chromite and PGMs the two most economically important components of the Bushveld Complex. The lower group (LG), within the critical zone, consists of seven chromitite layers and it is within this sequence of chromitite layers, the most important target of the lower chromitite group is found, ie the LG6 chromitite unit. The LG6 chromitite unit consists of a chromitite duplex composed of the lower LG6 chromitite layer (Steelport seam), averaging 1 m thick, overlain by a 0.66 m waste parting and a thin 0.34 m thick LG6a chromitite layer (leader layer).Two mining methods are commonly applied in the Bushveld Complex to extract the LG6 chromitite layer package. One method consists of footwall development utilising rail bound equipment to gain access to the orebody and then extracts only the LG6 chromitite layer by means of hand held rock drills and scraper winches. The second method is the use of mechanised equipment to access the orebody on the plane of the ore utilising bord and pillar mining method, which extracts the full mineral resource, ie the LG6 and LG6a layers. Conventional narrow vein stoping is often selected due to the large conventional mining skills base found in South Africa, the perceived cost and dilution implications of utilising mechanised equipment, and the difficulties of using mechanised equipment at dips above 12¦. The driving factor for mechanised mining is the perceived ability to access the orebody quickly and inexpensively, and extract the entire mineral resource package (LG6 and LG6a) while limiting capital expenditure and improving safety.This paper investigates these two commonly applied approaches, highlighting the benefits and problems associated with the two approaches. Comparisons will be made of the two mining methods and recommendations given for the mining engineer to consider before selecting the appropriate mine design.

Dec 6, 2010

By Chugh Y. P

A simplified, three-dimensional, time-dependent, mechanistic model of the overburden-coal seam-floor interaction has been developed and validated at two Illinois coal mines. The model based on the thin plate theory can involve any complex layout of mine workings, time-dependent sequence of extraction and, rheological properties of immediate floor strata. The model output data consist of spatially distributed surface subsidence and its slope and curvature, as well as load acting on pillars in one or more panels. A comparison of calculated and monitored surface subsidence or in- mine convergence measurements has proven the model's effectiveness for surface subsidence and load transfer Prediction.

Jan 1, 1992

Based on a principle developed at a South African Mine, the CSIR developed a device with which the alignment of guide rails in mine shafts could be measured. Originally the technique could only be used to obtain guide misalignment values at the bunton sets. At the time this was considered adequate since it was assumed that guide realignment could only be done at the support points anyway. The technology was developed further and now it is possible to obtain æcontinuousÆ guide profiles from the measurements. Software was developed with which a guide realignment schedule can be drafted and the shape of the realigned guides can be predicted. A measuring system based on this technology is being used to conduct guide alignment measurements in shafts. The data is then analysed and a realignment schedule is recommended in consultation with the mine. Such a schedule may be prioritised so that the worst sections in the shaft are dealt with first. The measurement hardware and analysis software are described. Examples are presented that illustrate the principles and highlight measurement errors. A case study illustrates measurements recorded in a newly equipped shaft. A repeat measurement, 18 months later, shows the effect of recommended realignment as well as the change in guide alignment over this period.

Jan 1, 2005

By G Kluck, N Stoitis, D R. Seaman, R A. Lauten

The presence of clays, in particular clay slime, may complicate many mining operations. Clay slime particles may possess a negative or positive charge depending upon the pH in the process and their presence may lead to reduced recoveries in flotation processes. It is assumed that slime particles may adsorb onto the surfaces of the minerals to be floated and by doing so, reducing the efficacy of the flotation chemicals. In this work it is shown that addition of a small amount of dispersant, either a polyacrylic acid or an anionic polyphenolic polymer, increases the recovery of copper and gold, both in laboratory trials and in plant testing of an ore with high clay content. Measurements of adsorption isotherms reveal that the tested dispersants show preferential adsorption towards the clay minerals present, suggesting that the improved recovery upon dispersant addition occurs by prevention of attachment of clay slime particles onto primarily chalcocite but also chalcopyrite.CITATION:Seaman, D R, Lauten, R A, Kluck, G and Stoitis, N, 2012. Usage of anionic dispersants to reduce the impact of clay particles in flotation of copper and gold at the Telfer Mine, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 207-214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Cunningham DA

Plant based on the New Jersey refluxing process has been installed at the Cockle Creek Works of Sulphide Corporation Pty. Limited to refine portion of the zinc output from the Imperial Smelting Furnace. Refining of impure zinc is effected by distillation in two stages in vertical columns compris- ing a series of superimposed silicon carbide trays designed such that ascending zinc vapours and descending liquid metal are in intimate contact. In the first stage the volatile elements (zinc and cadmium) are distilled from impure metal, condensed, and while still molten, fed to the second column in which zinc is boiled under controlled refluxing conditions to remove the cadmium content. The resultant zinc has a purity in excess of 99,995 per cent zinc. The availability of refined zinc has made possible the production of a number of zinc alloys for marketing in addition to the basis grades of zinc.

Jan 1, 1969

The Government Mining Engineer of South Africa has decided to legislate that Self Contained Self Rescuers (S.C.S.R.) become a mandatory piece of equipment for all those persons proceeding underground. It is envisaged that: * employees in underground coal mines will be fully equipped with S.C.S.R.s during 1988; * those persons employed in gold mines during 1988/89; and * personnel in all other mines by the end of 1990. It is the intention of this paper to discuss the introduction of these auxiliary life support systems, and to give an update on current market developments.

Jan 1, 1988

By Vutukuri VS, Budavari S

During recent years many investigators have suggested large spacing to burden ratios to improve the fragmentation obtained in blasting. In spite of these suggestions, most operators still use a conventional ratio of 1 to 2. From single hole longitudinal charge tests in laboratory, it is shown that burden controls the fragmentation. The burden for obtaining uniform fragmentation is smaller than the burden to obtain maximum breakage. Tests on two or three holes show that a larger spacing to burden ratio can be used for smaller burdens, but it is not possible for the larger burdens chosen to obtain maximum breakage. By using finite element analysis evidence is presented to show the effect of spacing and burden relationship on blasting results.

Jan 1, 1975

By Houlihan RN, Landau J

A reciprocating plate column is described in which two sets of perforated plates are mounted alternately on two shafts and are reciprocated with a phase difference of 1800 between them. It is shown that such a column is mechanically superior to the previously proposed types: under practical operating conditions the pressure fluctuations at the base of the column are only a small fraction of the static head. Furthermore, mass transfer experiments with the system tributyl phosphate in kerosene- acid aqueous solutions of uranyl nitrate show that both high specific throughputs and reason- ably good efficiencies can be attained in this type of column. A comparison with the more conventional extraction equipment (mixer -settlers, pulsed columns) on the basis of residence time per equilibrium stage indicates the potential of reciprocating plate columns in hydrometallurg- ical application, especially in which the requirements of separation efficiency are modest while the scale of operation is large.

Jan 1, 1975

In current mining practices it is desirable to bring about a substantial increase in both rate of face advance and productivity, thus compelling the mine engineer to consider better and more productive ways of mining. Transportation plays a vital role in achieving improved productivity. This paper focuses on horizontal transportation systems. Horizontal transportation is defined from the shaft station area to the end of the stope cross-cut. Traditionally, horizontal transportation is inefficient in comparison to vertical transportation efficiencies and accounts for a high proportion of South African mine accidents. Thus, the role of horizontal transportation has been investigated in detail, as it offers the greatest chance for improvement. The purpose of the paper is to provide a best practice guideline for the design of horizontal underground transport systems. It is intended that the document be used by mine designers and planners as an aide memoir during the design process and benefit may well be gained from retrofit and reorganisation activity. The paper looks at transport systems suitable for deep level gold mining in South Africa and evaluates such items as management, scheduling, and haulage systems. Current transportation systems for personnel, material and rock transportation are evaluated, gaps in technology highlighted, and recommendations made.

Jan 1, 2003

Powercoal Pty Ltd operates eight underground coal mines in New South Wales and produces coal for both domestic power stations and the export market. Approximately 40% of total production is from continuous miners. Over the past five years, place change mining methods have been introduced to improve productivity from continuous miners. This has involved utilising the existing coal clearance system from the continuous miner to the ratio feeder using trailing cable shuttle cars.By late 1996 average productivity at Cooranbong Colliery using this system had plateaued at 800 tonnes per eight hour shift. A number of factors were identified to increase average productivity to 1500 tonnes per eight hour shift. An improved coal clearance system was one of the factors identified.

Jan 1, 1998

The correct design and effective operating strategies of metallurgical plants require a constant analysis of data gathered for process control, or for due accountability. Conventional, oldfashion statistical tools often fall short of helping management, either because they are too complicated and ambiguous, or because they fail to address structural problems leading to causes of setbacks. This paper focuses on three statistical tools known for their practicality and the in-depth perspective they offer in attempts to retrieve important information from existing data. These tools also provide a better appreciation of the importance of carefully selected data quality objectives. Chronological data are meticulously gathered and stored at considerable expense: They have value, and it is the duty of management to take full advantage of them. These three selected tools are the variogram and its auxiliary functions, the moving average and its auxiliary functions, and the relative difference plot. This paper offers solutions, and a reference for managers to optimise metallurgical plants.

Jan 1, 2002

By A J. Moore

To control the airblast from blasting to regulatory limits at environmentally sensitive sites near the Collinsville Coal Mining Operations, it has been necessary for Thiess Mining to incorporate a wavefront reinforcement analysis model in the predictive environmental airblast design. Controlling airblast from cast blasting 70 m high faces with 2000-3000 kg of explosives per hole within 700 m of houses presents a considerable challenge to the blasting personnel. This paper describes the model used and summarises the results of an investigation designed to quantify the increase in airblast indicated by wavefront reinforcement diagrams to further calibrate the model for future prediction.

Jan 1, 2004

By A Murphy, D Lauder, J Miranda

Minera Alumbrera Limited operates the Alumbrera concentrator, treating a nominal 80 000 tpd of porphyry gold/copper ore. It is located in Argentina, 1200 km north-west of Buenos Aires in Catamarca Province, at an elevation of 2550 m above sea level. Treatment facilities consist of crushing, SAG and primary ball mill grinding circuits, rougher flotation, ball mill regrinding, gravity recovery and cleaner flotation. It is one of only a small number of concentrators in the world, which uses Jameson Cells alone for cleaner circuit flotation. Plant design was started in June 1995, with commissioning commencing in July 1997. Following a successful ramping up to design tonnages and recoveries, a number of options were reviewed to improve gold and copper recoveries. This paper concentrates on a detailed size by size flotation recovery project, commenced in May 1999. Utilising optical microscopy, scanning electron microscopy and analysis of surface chemistry it has allowed losses by size fraction to be quantified and options for enhanced recoveries to be developed. Coupled with extensive circuit surveys it has also provided an insight into previously unknown properties of Jameson Cell operation. Among these are unique residence time and bubble formation reactions to reagent and pulp flow variations, which has permitted a number of novel changes to the operation to maximise capacity and recovery.

Jan 1, 2000

By P F. Knights

Mining companies are striving to achieve new levels of operational maturity and drive process improvement across the organisation in the face of unprecedented demand and limited supply of experienced human resources. Advanced analytics techniques can help overcome these fundamental challenges by applying data techniques not previously applied in mining. Today, decisions are usually locally optimised but do not achieve optimum capability for the value chain. Although more information is collected then ever before, it is difficult to link many sources of data together in the same place in real-time, for example plant history, maintenance, mine planning, logistics and engineering data. Consequently complex analysis of data is time consuming and requires specialist skills and knowledge, and is often neglected in the decision-making process. In the future, analytics will close the loop between analysing data and taking action. Analytics will become embedded in the business and routinely applied to improve decision making across the organisation, from senior management to operations and maintenance workers, but will not require specialist skills or be time consuming to analyse data. As analytics becomes embedded in the business process, decisions are supported by data (not on gut feel), and critically, data from many sources are integrated in real-time to improve the quality of decisions. Ultimately, predictive tools will help suggest, or even in some cases automate, courses of action. The main opportunities for analytics exist where the enterprise requires supporting technology to enable it to continue to evolve to higher level of maturity. This will be in the areas of asset management, rapid reconciliation and adaptive planning, and the inbound and outbound supply chains. Advanced analytics are also a key enabler for increasing the effectiveness and realising the true value of Remote Operations Centres to safely and efficiently support operations in remote locations with smaller workforces.

Jan 1, 2008

The comminution process indicates that the most energy-efficient comminution system would be one where the particles leave the breakage field as soon as they reach product size. Contrary to the free falling gravitational (vertical) flow in crushers, the grinding millÆs energy efficiency essentially depends on ore characteristics and the discharge rate of broken particles, which in turn depends on how efficiently the discharge pump (grate and pulp lifters) operates. The essential function of a pulp lifter is to transport the broken material and slurry from the discharge grate out of the mill. Hence, the design optimisation of pulp lifters affects not only the energy efficiency and throughput of autogenous grinding/semi-autogenous (AG/SAG) grinding mills, but also contributes other process benefits such as improved wear life and operator-friendly steady and smooth mill operation. Following its introduction in 2006, OutotecÆs patented Turbo Pulp Lifter (TPLÖ) design has been retrofitted at existing sites and also installed in some new ones around the world. This paper will provide operational experience and data on how the TPLÖ design has allowed AG and SAG mills to operate efficiently.

Jan 1, 2009

By H Bartosiewi, M Kuruppu, F Mashiri

Wire ropes are one of the most heavily used components in a dragline. They are subjected to harsh conditions during the regular usage of a dragline in a mining operation. Hoist ropes are subjected to fatigue due to the cyclic nature of load handling as well as due to rope bending over the sheaves and the drum under load. This leads to wire breaks due to fatigue. Accumulation of a number of wire breaks close to each other can have a detrimental effect on the rope. Furthermore, to allow for the increasing demand for higher load capacity coupled with the inconvenience of having very large ropes, the factor of safety is often compromised, which increases the wear rate. Drag ropes are also subjected to heavy loads. More importantly, they are allowed to drag along the rough mine surface subjecting them to external physical abrasion. This makes the life of drag ropes one of the lowest among those used in a dragline. Suspension and IBS ropes are relatively uniformly loaded during their regular usage although they need to withstand dynamic load cycles as well as bending. Hence they tend to last for a number of years on average. The paper analyses the wear types and their severity of each of these rope applications, and suggests methods to determine rope wear rates and the resulting rope life. The paper further gives suggestions for good operating and maintenance practice that can extend the rope life and help reduce the large expenditure associated with every major rope change in a dragline.

Jan 1, 2005

By Borshoff J, Von Pechmann E

The uranium mineralization in the White's East area of The Embayment is hosted by Lower Proterozoic schists of the Masson Formation which have undergone polyphase de- formation and upper greenschist metamorphism. Significant mineralization is also present in apatite rocks. The ore zones occur near an unconformity with overlying Middle Proterozoic sandstone and breccia conglomerate. Kink breccias and fracture systems related to post Middle Proterozoic reverse faults are the con- trols for mineralizing fluid migration. Pitchblende is the main uranium mineral and it occurs as fine disseminated grains, fibrous webs, clusters composed of botryoidal aggregates and locally as veins. Two genera- tions of uranium mineralization are present. The first generation (pitchblende I) occurs as fine grained inclusions within chlorite II, and the second (pitchblende II) as hydraulic fracture networks and massive veins intimately associated with sericite-hematite-chlorite III. Two hydrothermal alteration phases have affected both Lower Proterozoic and Middle Proterozoic sequences. The most extensive alteration mineral is chlorite, of which a number of varieties has been identified. Mg-rich chlorites are generally associated with the first phase alteration assemblages and are commonly replaced by hematite, seri- cite and Mg-Fe chlorites in massive pitch- blende zones. Other alteration minerals in- clude tourmaline, apatite, talc, quartz, magnesite, graphite, pyrite and rutile.

Jan 1, 1984

Economic and technical reasons forced the mining industry all over the world to increase the unit size of mineral processing equipment. in large flotation cells, this development leads to problems in areas of air dispersion and keeping solids in suspension. Outokumpu, an operating mining company, designed and developed a mixing mechanism for large flotation cells at its own concentrators and also studied problems related to tank design. Ideal conditions for flotation can only be achieved if the flow pattern created by the mixing mechanism fits well into the tank configuration and the risk of short circuiting is minimized. In large deep flotation cells, four different zones can be found which improve the behaviour of large cells when compared to small cells. Selectivity is increased and in some cases final concentrate grades can be produced from the rougher cell. The largest units have also been used as final cleaners in some installations. When modernizing old plants by installing fewer larger flotation cells, immediate and substantial savings in power consumption are achieved. Additional power savings are made in pumping costs because of simpler circuit design and decreased circulating loads

Jan 1, 1978

'Industrial Minerals - their mining and use in New Zealand' is the theme of the 1978 Annual Conference of the New Zealand Branch of The Australasian Institute of Mining and Metallurgy. This paper describes the use of phosphate rock, sulphur and potassium chloride (potash) - three industrial minerals which have enabled the farmers of New Zealand to increase production to current levels. The growth of imports of these raw materials for the New Zealand fertiliser industry is well documented in NZ Fertiliser Statistics 1977. This is the most recent of the Ministry of Agriculture and Fisheries annual publications on this Subject prepared from the detailed returns of fertiliser manufacture and sales from each fertiliser works. There are now 12 of these works in New Zealand one of the most recently established being in Whangarie where this conference is being held. Its capacity to manufacture superphosphate will shortly be 300 000 tonnes twice that when it opened late in 1964. New grinding and manufacturing equipment comes on stream early in 1979. This paper illustrates the interdependence of two primary industries, agriculture and mining. New Zealand's economy in the foreseeable future will be based on agriculture so that our standard of living is dependent on the overseas prices and freight costs of the bulk raw materials from which our fertilisers are made. For the year ended 31 March 1978 New Zealand's total exports were $3395 million, of this total $2413 million (71%) came from the products of pastoral agriculture (wheat, wool, dairy and other animal products), $291 million from forest products and $501 (15%) from manufactured exports. Approximately half of the pastoral receipts can be attributed to the fertilisers applied at a total cost of about $200 million including subsidy.

Jan 1, 1978

By P Townsend, F Russell

Palabora Mining Company operates an integrated open pit mine, concentrator, smelter and refinery complex located in the Northern Province of South Africa. The Palabora open pit went into production in 1966, mining 30 000 t/d to produce some 62 000 tpa of copper. With continuous modification and improvement, a mining rate of 82 000 t/d, producing up to 135 000 tpa of refined copper, has been achieved. While these improvements have also enabled the mine life to be nearly doubled, the open pit will reach the end of its economic life by 2003. The Palabora orebody is vertical and the reserve extends to a depth of 1800 m over an area of 700 m by 200 m. Studies to assess the economics of mining the orebody by underground means began in the mid-1980s. These studies indicated that block caving is the lowest cost underground mining method that would generate a suitable return. In March 1996, a decision was made to develop a 30 000 t/d block cave mine that will extend the life of the Palabora Mining Company by a further 20 years. In terms of the relatively high rock strength and the resultant coarse fragmentation that is expected at the drawpoint, the Palabora cave can be considered rather unique when compared to other block cave operations. This paper describes the project in broad terms and details the mining method, particularly with respect to the cavability of the orebody and the design features to deal with the coarse fragmentation. The project commenced in July 1996 and final development of the undercut and drawbells is scheduled for completion in November 2003. This paper describes the status of the project and planning as of April 2000.

Jan 1, 2000