Search Documents

By J Välivaara

The mining industry will face numerous challenges over the next 10–15 years as new deposits are likely to be more remote and lower grade and existing deposits will be mined deeper. As a result, mines and mining contractors operating in deep-mine conditions will need to focus on the quality of drilling and blasting to minimise unnecessary waste rock excavation to keep costs at an acceptable level. In addition, increased demand for improved safety and operator ergonomics will set greater demands on original equipment manufacturers of mining equipment. Finally, difficulties finding a skilled and experienced workforce, particularly in remote mine locations, have already negatively impacted mines’ ability to achieve high productivity and low operating costs.This paper introduces techniques and shares practical experiences in increasing productivity and reducing the costs of excavation in underground face drilling. The paper uses Sandvik’s new DD422i automated mining jumbo as an example of the type of equipment needed to deliver the features and corresponding benefits for future mine development. Case studies using this equipment are presented to illustrate the points made in this paper.CITATION:Välivaara, J, 2016. Automated drilling features for improving productivity and reducing costs in underground development, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 723–730 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By P Kappen, R N. Collins, K M. Spiers

X-ray absorption spectroscopy (XAS) is a synchrotron-only technique used to determine chemical speciation, providing a powerful alternative to most traditional ‘wet chemistry’ and lab-based speciation methods. XAS is an element specific method that can be used to address a variety of systems, ranging from heterogeneous to homogeneous, polycrystalline to amorphous, and solid to liquid. The strength of XAS in identifying and managing chemical species in tailings and mine waste is demonstrated, with the presentation of highly relevant studies into lead, uranium, chromium and arsenic speciation. In each example, waste samples are compared with known standards, allowing an assessment to be made of the quantity of particular chemical species in each.CITATION:Spiers, K M, Collins, R N and Kappen, P, 2015. ‘Forget the wet chemistry’ – how the Australian Synchrotron can help with tailings and mine waste management, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 145–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Mahoney BK

The development of simulation models to reflect accurately the operations of a port and its associated transportation systems can be an expensive and time consuming process. However the complexity of such operations leaves little choice for other than simulation techniques since analytical methods are rarely appropriate. The development of suitable software has now reached the stage that these techniques can be used with confidence. Types of simulation models and their requirements are discussed together with the results from some recent applications to the planning and management of bulk terminals.

Jan 1, 1983

By C Fong

Compliance Planning is an active approach to ensure mining operations align more closely to their longer-term plans. Through Compliance Planning, operations can not only measure their performance on intervals as short as intra-shift, but they can then apply corrective measures to ensure they remain as close as possible to the plans. Compliance Planning targets short-term and execution level teams, as these are the shortest duration planning divisions commonly found in mining operations. Compliance Planning combines live information with intelligent planning capabilities to provide a framework that enables mining operations to realise a significant improvement in reconciliation of plan to actual movements.

Jun 22, 2022

Flat jack stress determinations in selected colliery roadways have revealed a range of measured stress from 330-p.s.i. tension to 3,750 p.s.i. compression. Photoelastic examination of loaded plastic and actual rock mo.odel mine openings has shown that the primary horizontal stress required to attain these measured stresses would be from one to three times the superincumbent vertical load.Examination of roof movement with a. borehole oxtensumeter and a series of anchors at various horizons to 30 feet in a. vertical roof borehole showed that when a standing face waa.s advanced the roofmovement was practically confined to the lower two feet. The ma.j ority of this movement occurred during the 36 hours after mining at this face commenced.The use of a. radioactive isotope and a. scintillation counter in a. pair of parallel bcreholes promises to be sensitive and accurate method of roof bedding plane crack detection.

Jan 1, 1963

By Munive L

As a result of commissioning No.5 B F, 2670m3 inner volume, in March 1972, the largest B F in Australia; new expertise in maintenance, furnace operating practices and design have been obtained. This experience has also been extended to the other furnaces. A series of operating problems were con- fronted; all parts of the furnace, including the hearth side walls and bottom,were adversely affected. In December 1977, serious hearth wall wear was detected at No.5 B F, and a potential hearth breakout was averted. Hearth wear in No.4 B F was discovered in March 1979, and emer- gency underhearth cooling was installed to reverse an extremely advanced hearth bottom erosion. Hearth behaviour of No.5 B F oampaign 1972-1978 and`No.4 B F campaign commencing 1972, has been studied and discussions on the causes, effects and measures undertaken to protect the hearths are presented in this paper.

Jan 1, 1981

By Kennerley P

A significant part of the reserves of the Southern Coalfield lie beneath major water storages and their impounding dam structures. One of the functions of the NSW Government's Dams Safety Committee is to specify the particular mine layouts which can be used beneath the stored waters according to certain guidelines. A study was made of examples of the two different methods of extraction used under the stored waters as proposed by the mining company according to the guidelines and approved by the Dams Safety Committee. Using both pillar monitoring and mathematical modelling approaches it was shown that the recovery of coal from these layouts could be improved while still ensuring the long term stability of both the underground support pillars and the body of the strata. The integrity of the water storages and their impounding structures would therefore not be Affected.

Jan 1, 1986

By Torckler L, Brathwaite R. L

At Neavesville gold-silver (electrum) mineralization occurs in steeply-dipping zones of intense fracturing, brecciation and quartz veining within rhyolitic pyroclastics, carbohaceous shales and andesites. Hydro- thermal alteration extends over an area of greater than 3 by 1.5 km. In rhyolitic tuffs, highly silicified zones containing quartz- adularia-illite assemblages are flanked by less silicified assemblages composed of albite, illite-montmorillonite and chlorite. The mineralogy ana sequence of alteration are comparable with the alteration zones which envelop the steam-producing fissures of the active Wairakei and Broadlands geothermal fields. Primary fluid inclusions in quartz from five fissure veins in the Neavesville field show maximum homogenisation temperatures ranging from 220 - 260¦C and salinities of 0.0 - 1.1 wt. % NaCl equivalent, which cover a similar range to actual measured temperatures and salinities in geothermal fluids at Wairakei aria riroaolan¦s. The age of the rhyolitic pyroclastics and related alteration and mineralization is probably Pliocene and Neavesville therefore represents a fossil geothermal system.

Jan 1, 1980

By Dunlop JSF

A description of general mining proced- ures and tyre maintenance practice is given with particular reference to tyre mainten- ance facilities and record keeping at Groote Eylandt. Experience with tyre wear on Wabco 85C rear dump trucks is then outlined, concen- trating on wheel camber, wheel alignment, truck speed, tyre pressure, loading and haul road design. T T.1TUnilhTPTTnAT The Groote Eylandt Mining Company Pty. Limited mines and beneficiates sedimentary manganese ores from a series of orebodies occurring in the western part of the island. The island is one of a group on the western side of the Gulf of Carpentaria, about 50 kilometres from the Arnhem Land coast and about 650 kilometres from Darwin. Whilst capacity of the mine is presently 2.3 mil- lion tonnes of product per annum, current production has been reduced to just more than half this figure, due to a general mar- ket recession.

Jan 1, 1982

For the past 40 years, underground trucking using diesel powered or electric wheel driven vehicles, either conversions of surface trucks, or purpose built, has been the preferred means of ore and waste transport in underground mining. The relatively low capital cost, flexibility and requirement for minimal infrastructure means that trucking systems are selected in the early stages of a mining operation. An increase in the carrying capacity of trucking systems with dimensions to operate within existing development excavations is the solution to long term ore and waste underground haulage systems using trucks. The next generation of underground trucks will be low profile articulated trucks with carrying capacities up to 60 t.

Jan 1, 1998

By Warren R

Croesus Shaft is one of two operating shafts on North Kalgurli Mines Limited's Fimiston lease.At the cessation of gold mining in 1974, the workings at Croesus were allowed to flood. Large quantities of deslimed mill tailings used in filled stopes were washed into the shaft and surrounding drives, making re-access very difficult. The shaft has been desludged from the 9 level to the 15 level, and a loading pocket installed below the 14 level. A vacuum lift unit was installed underground to facilitate the removal of the slime and spillage.Stoping at Croesus was hampered by poor drainage, pumping, and shaft availability. These difficulties have been overcome by utilising an open stoping system for the relatively steep, narrow, high grade stopes. Open stoping has proved to be effective and economic.

Jan 1, 1985

Increasing demands on quality of metallurgical grade alumina and for lower production costs led to the development of a new fluid bed calcining process. The process, jointly developed in Germany by Vereinigte Aluminium Werke A.G. and Lurgi Gesellschaften m.b.H., takes advantage of modern chemical engineering methods such as counter-current flow of combustion air and solids, direct heat-exchange between combustion air and fine solids and near stoichiometric combustion of oil in a fluid bed. Using a two-stage Venturi-type suspension preheater for heat-recovery from combustion flue- gases, the circulating fluid bed technique with internal oil combustion at 2.2000 F for the calcining step and 'a five-stage fluidized bed cooler for heat recovery from calcines, the process gives an outstanding heat- efficiency. In a first industrial plant for 560 sh. t. alumina per day heat consumption figures of less than 1.400 BTU/lb A12O3 were achieved.

Jan 1, 1971

By Beech-Jones J. M

At Port Latta in Tasmania, Savage River Mines operates vertical shaft furnaces for the firing of pelletised magnetite concentrates. At times the temperature profile of the furnace has changed markedly, necessitating the- burning of greater quantities of fuel to maintain good pellet quality. A study of the oxidati=of magnetite concentrates was under- taken because this exothermic process supplies much of the heat required to indurate the pellets. Using the thermal analyses methods, different magnetite concentrates from Australian and overseas were heated in air under identical conditions, to compare rates of oxygen uptake and of heat release. In addition, a compari- son was made of the oxidation behaviour of different particle size fractions of a selected concentrate. Particle size analyses, x-ray diffraction and dilatometer tests were used to aid inter pretation of the thermal analysis traces. The investigation emphasized the importance of particle size and ferrous iron content in determining' oxidation rates from the commencement of heating.

Jan 1, 1974

By C Wu, H Chen

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.The Halasu porphyry copper belt, located in the East Junggar basin bounded by Chinese Altay to the north and the Tianshan mountains to the south in the Central Asian Orogenic Belt, is one of the major porphyry copper belts in Xinjiang province, north-west China. Combined with previous studies in this area, the magmatism can be divided into three periods: pre-mineralisation activity of 390 Ma syn-mineralisation activity of 380–370 Ma post-mineralisation activity of 360–330 Ma.Through the comparison of zircon chemistry from ore-bearing and barren syn-mineralisation intrusions, negative correlation was identified between Ti-in-zircon temperatures and oxygen fugacity, corresponding to the fact that late-stage syn-mineralisation granitoids contain high water content, high oxygen fugacity and low temperatures with higher mineralisation potential. In addition, the relative low initial 87Sr/86Sr ratios, high eHf(t) and eNd(t) values and mantle Pb isotope characteristics in this study support that the magma forming these intrusions was probably derived from juvenile crust generated during subduction-accretionary processes.CITATION:Wu, C and Chen, H, 2015. Zircon trace elements and Sr-Nd-Pb-Hf isotope systematic of the Halasu porphyry Cu belt, north-east Xinjiang, China, in Proceedings PACRIM 2015 Congress, pp 637–640 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By C T. Dunbar, P A. Walker, G E. LeJuge

A programme of blast improvement was initiated at the Mt Whaleback iron ore mine by BHPIO management in early-1998. One component of that work was the need to improve wall control blasting practices to better achieve the designed pit slope elements. This paper describes the geological conditions in which pit walls are developed, the mine operating equipment, the blast design concepts applied to minimise blast damage, the techniques applied in an assessment of the blast performance and the operational procedures developed to ensure that the blast concepts are effectively implemented in the production environment. Substantial changes have been implemented in both technical and operational aspects of the mining operation in order to achieve the improvements in pit wall condition, in particular recognising the need for a more flexible approach to limits blasting in response to highly variable and complex geology. The benefits to the mine are not only an improved wall condition, but increased confidence on the part of mine management that mine plans may be implemented on design and on schedule.

Jan 1, 2001

Minerals similar to the indicator minerals used in kimberlite exploration are widespread in the Cainozoic alkali basalts of north Queensland. Magnesian ilmenite, pyrope garnet, chrome diopside, chrome spinel, phlogopite and zircon were recovered from most of the localities examined. The occurrence of these minerals creates significant problems when indicator minerals are used for diamond exploration. Basaltic ilmenite is visually similar to kimberlitic ilmenite. Untransported grains are rounded and have pitted surfaces. Basaltic ilmenite grains often have exsolution lamellae and reaction rims of titanomagnetite. Although kimberlitic and basaltic ilmenite are chemically similar, basaltic ilmenite grains are usually less magnesian than their kimberlitic counterparts. Basaltic ilmenite contains very little Cr203. Pyrope garnet occurs as megacrysts and in a variety of xenolith lithologies in north Queensland basalts. Most basaltic garnet is Cr-poor and comparable with kimberlitic garnet from Groups 3 and 5 of Dawson and Stephens (1975). Wine-purple, chrome-bearing garnet is common in kimberlite but rare in basalt.

Jan 1, 1984

By Kaleta S, McTavish LP, Turner RD

Primary production blasting at Hamers- ley Iron began with seven inch holes at Tom Price in 1966 and has developed since then to large multiple row shots of 381 mm holes at Tom Price and 311 mm at Paraburdoo. Up to 1.3 million tonnes are initiated in a single blast with the average around 300,000 tonnes. Development can be traced through Anfo, AlAnfo, slurries, various boosters, initiation and delay techniques, hole loading and daily operating practices. A standard practice could be developed for the two mines for normal pro- duction blasts; this would not apply to such common variations as low "paddy" shots, pre- splitting, tight corners necessitating single row drilling etc. Because of ground variation three or even four sizes of drill holes may well be economic- al for blasting, even though this would be off set by complications in operation, supervision, store stocking and maintenance, particularly in Drilling.

Jan 1, 1978

ecent work on decoppering lead is reviewed; CuS is formed rapidly even from dilute solutions of copper in lead. he mechanism of decoppering is discussed, and an explanation for the retention of metals such as silver in lead is dvanced. As decoppering tin appears to be an analogous process, the Cu-Sn-S system is studied at 300¦C. CuS, hich is not, an equilibrium product, is found in decoppering drosses. In the removal of nickel from lead, Ni3pb2S2 formed; preliminary measurements show the equilibrium nickel content to be greater than that obtained by tirring in sulphur. Decoppering bismuth is thermodynamically favoured, but is complicated by the occurrence of uBiS2. The Cu-Pb-S system is the only one of the four studied where the equilibrium can be calculated simply, as ' resence of ternary sulphide or other phases invalidates calculations based on binary data.

Jan 1, 1970

By H Han, X Wang, T Li, D Duan

"In this paper, the reduction and separation behaviour of iron and slag in carbon composite iron ore pellets has been investigated experimentally using an electric resistance furnace simulating a rotary hearth furnace process. The factors that affect the formation of iron nuggets, such as temperature, holding time, molecular ratio of C/O and basicity, are discussed. Results show that the reduction of iron ore, carburisation of reduced iron and the composition and quantity of slag are very important for producing iron nuggets. Through optimisation of process parameters, iron nuggets can be formed below 1300¦C when holding time is 20 minutes, C/O is 0.7 and basicity less than 0.5. This study provides a theoretical and technical basis for iron nugget production.CITATION:Duan, D, Han, H, Wang, X and Li, T, 2013. Iron nugget production technology in rotary hearth furnace process at lower temperature, in Proceedings Iron Ore 2013, pp 363-368 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By Wilson J. R

The main mining method employed at Mt Lyell is sub-level open stoping with a typical extraction level interval of 100 m and sub-level intervals of 30 m. Currently, pillar blasts provide the major portion of broken ore and firings are in the order of 200 000 to 300 000 tonnes while future firings of 500 000 to 300 000 tonnes are planned. Improvement of blasting techniques in these mass firings has been necessary for the following reasons. 1. Extremely wet ground conditions have adversely affected ANFO performance and placed extreme pressure on the charging and priming phases. 2. As pillar blasts increase in size the problems of wet ground conditions are accentuated resulting in very slow loading of wet upholes with cartridged gelignite and unreliable charging of the remainder with ANFO. 3 Fragmentation in pillar blasts has suffered because of the above, result- ing in increased secondary breaking costs and difficulty of extraction.

Jan 1, 1977