Search Documents

Rheology is the science which deals with the deformation and flow of matter. Thus rheology is concerned with the flow of any material. The mining industry is concerned with digging things out of the ground, extracting the good stuff and throwing away the bad stuff. In the upgrading processes associated with mining, ie mineral processing, wet techniques are used where the primary material being handled is a particulate fluid, ie a suspension. After the processing operation, with the concentrates extracted, what is left behind generally is a wet material in suspension form, which may or may not contain reagents harmful to the environment. The amount of waste generated in any of the mining processes is large, in fact, the mining industry is the largest generator of solid waste in Australia. In order to minimise the waste generated within the industry it has become of interest to handle the particulate fluid wastes, or suspensions, at high concentrations, thus removing water and some of the reagents which may be harmful to the environment. The resultant highly concentrated suspension is a non-Newtonian fluid. Rheology deals with the flow of non-Newtonian fluids; therefore a combination of rheological understanding of high density suspensions, in conjunction with an understanding of the environmental problems being faced by the mining industry, can and has led to improved methods of waste disposal in the industry, ie waste minimisation. This paper describes the progress that has been made in the development of dry disposal technology in the mining and minerals industry in Australia.

Jan 1, 1998

By BTrubT M

In the roast-leach-electrolysis process for the production of zinc, iron contained in zinc concentrates is converted to zinc ferrite during roasting. At Canadian Electrolytic Zinc (CEZinc), the Outokumpu Conversion process is used to simultaneously leach zinc ferrite and precipitate the iron as jarosite. These simultaneous reactions, while providing good process stability, require a compromise between optimum conditions for maximum zinc extraction and efficient iron precipitation. An improved conversion process has been identified which can achieve >99 per cent zinc extraction and more efficient jarosite precipitation to residual iron concentrations of

Jan 1, 1993

By Hulton SJ, MacKenzie DH

The Broken Hill orebody within the leases of ZC Mines is still a major lead-silver-zinc resource after over 80 years of mining. It illustrates particular problems encountered in resource and reserve estimation in old mines. The six mined ore lenses are characterised by three features: ò complex external geometry, ò high internal grade variability, ò bimodal grade distribution. The high grade 3, 2 and 1 lenses and B lode have sharp external contacts but contain some low grade internal zones. By contrast A lode is of lower average grade and comprises an extensive but geometrically variable mineralised zone within which are numerous irregular bodies of high and medium grade ore. Geological factors are the main source of variability in reserve estimation, which historically has been conservative. For many years the geological resource tonnage has been maintained at a level sufficient to make up for extraction but at a gradually declining grade. Using a geological block cut off grade of 10% Pb + Zn the present in situ resource is 53.8 Mt grading 8% lead and 13% zinc. Using empirical cut factors a "recoverable reserve" is derived from this large geological tonnage. There is some doubt that the "recoverable reserve" is conservative enough to reflect mining reality. The most sensitive indicator of forthcoming change in total resource or insufficient drilling and development is given by changes in the tonnage and grade of possible ore from which the proved and probable categories are derived. Examples are given to show that where reserves are drill indicated, the delineation required for proved ore reserves must be enhanced to achieve final stope design. The move in recent years to greater emphasis on non entry mining and lower recovery of in situ material poses a dilemma for a mine which has practised 100% recovery for much of its past. The need for a realistic reserve assessment in current terms needs to be balanced against the fullest possible geological knowledge of the resource to cater for future technological developments.

Jan 1, 1987

By D MacKenzie

The Rise & Shine Shear Zone is a shallow-dipping Cretaceous late metamorphic shear zone formed in a compressional environment. The Shotover mineralised system is dominated by normal faults with well-defined vein systems that cut across Miocene schist folds and faults related to the inception of the Alpine Fault. Despite the geological differences between these mineralisation systems, they share many common features of hydrothermal alteration that have resulted in disseminated gold in altered sheared schist. The most distinctive feature of both systems is the abundant ankeritic carbonate that has formed from decomposition of metamorphic chlorite. Excess iron from this alteration reaction combined with hydrothermal sulphur to form sulphides that host the disseminated gold. The chlorite decomposition reaction was reversed in the latter stages of both mineralisation systems, and this was accompanied by further gold emplacement in the Rise & Shine system.   Both alteration systems involved initial decomposition of metamorphic albite, followed by deposition of albite as a vein mineral in the latter stages. The fluid flow that yielded the disseminated gold was controlled by microshears that pervade host schists, in strong contrast to many Otago Schist vein systems where host rock alteration is absent. The ankeritic alteration in the Shotover and Rise & Shine mineralised systems has increased the volume of mineralised rock, and may have made suitable targets for large-tonnage, low grade gold deposits.

Jan 1, 2007

By Nagai K, Moriyama K

Toyo smelter has been making s veral efforts to reduce and diversify energy for dealing successfully with such :n:;rgy problems as the first and second oil crises. ::,specially it is one of th:; most important subjects to substitute oil by alternative: energy source, because oil is expensive and unstable with respect to its supply. t _'hercfore i was decided to propel tnC ezhstitution of coal *jr oil. in the first place, the supple- mental fuel oil in the reaction shaft was replaced by oil to coal in 1981, and then th, fuel substitution of pulverized coal was achieved in the steam superheater in 1984. 3y these fuel substitutions about 7u,' of the total fuel energy at 2oyo smelter has been replaced by coal. in this paper the fuel substitu- tions at loyo smelter are described in detail.

Jan 1, 1987

By Kidman B. E

The Fitzpatrick area is the deepest section of the North Mine, with the orebody located between 1450 and 1800 m below the surface and some 600 m NE of the main No. 3 Shaft orebody and separated from it by the intensely sheared Globe Vauxhall Shear Zone. Development towards the Fitzpatrick area commenced in 1977 after earlier initial exploration drive development. However, it was not until 1982 that mining in the Fitzpatrick area actually began with the silling out of No. 36 level at a depth of some 1600 in. Since that time mechanised cut and fill mining from an incline ramp system with connecting stope accesses has progressed some 25 m above No. 36 level. Initial sill development on No. 37 level at 1660 m depth also commenced in July 1987 to further develop the Fitzpatrick area.

Jan 1, 1988

By A T. Spathis, K E. Leslie, K R. Blay

Many open pit mining operations seek to control blasting-related movement of ore and waste to minimise loss and dilution. Tracking the movement of ore boundaries can result in the maximisation of ore recovery and minimisation of waste sent to the mill, thereby optimising the economic performance of the operation.A novel solution for tracking the ore–waste boundary location before and after a blast uses subsurface markers placed along the boundary with all measurements and scans conducted remotely from the blast block. Upon system activation, user-operated equipment on the surface determines the three-dimensional (3D) location of the subsurface markers.The patented system concept combines two electromagnetic mechanisms, magnetic positioning and radio frequency through-rock communications to enable remote battery-powered markers, buried within the rock to be accurately located in 3D space.Field trials at a quarry have demonstrated the system can comfortably handle over 100 subsurface markers with a complete scan, including set-up, taking less than an hour. Location accuracy for each marker in 3D space is better than 0.5 m at a range up to 50 m from the magnetic source, and the system has an overall operational range in excess of 75 m.CITATION:Blay, K R, Spathis, A T and Leslie, K E, 2015. A remote, rapid and accurate three-dimensional ore waste boundary tracking system, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 297–306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

For the past five years the University of Queenslandhas, through its various workshops, been preaching to Australia that there was a potentially hazardous situation from earthquakes for urban Australia. A few people outside The University accepted this, but largely the warnings fell on deaf ears.The 1989 Newcastle earthquake changed that per-ception. The most important lessons to emerge from Newcastle were (i)the realization that in continental areas small earthquakes cause widespread damage:(ii)the local geology of an area is of great importance in the damage done by an earthquake.These two factors clearly indicate that, in the future, we must take far greater account of the "Urban Geology" of an area. This paper discusses the need for urban geology and its impact on seismic risk and compares that with the traditional methods of assessing seismic risk.

Jan 1, 1990

By Macaulay J

The recovery of gold from cyanide liquors is frequently effected by using activated carbon. Process economics however require non destructive methods of gold extraction from the carbon so that it may be recycled.Stripping at atmospheric pressure usingthe method of Zadra et al(l) suffers from the disadvantage of unfavourable kinetics with strip times of the order of 48-72 hours. Subsequent research has led to development of processes which strip the gold more rapidly namely: A.A.R.L. process, (2,3) organic solvent (4,5,6) and pressure stripping (7,8)This paper reports on a development of the pressure stripping technique in which stripping and electrowinning are carried out at elevated temperature and pressure.

Jan 1, 1984

By McQuade CV, Riley SJ

Acid mine drainage is an unavoidable consequence of some coal mining operations. Typically runoff pH is below 3.5 and at these pH levels heavy metals are mobilised. Leachate from coal reject dumps may require collection and treatment to raise the pH and precipitate the metals before being discharged.A bi-product of coal mining operations at Clarence Colliery is coarse washery reject. At present the coarse reject is deposited above ground and rehabilitated. Adjacent to Clarence Colliery is the Kable's Transport Pty Ltd sand mining operation. It has been proposed that co-disposal of the rejects from both operations may produce a product whose leachate has near neutral pH.

Jan 1, 1998

In order to satisfy environmental and mine operational requirements it is becoming increasingly important to minimise ground blast vibrations at certain locations. These locations are often in soil or on large resonant structures such as grain silos, highway bridges or even the walls of an open pit. A soil monitoring exercise was carried out to evaluate the common practice of coupling vibration detectors to the ground using spikes. At a series of locations in an operating quarry the spiked array response to single blastholes was compared with that of an accelerometer array attached to a calibrated embedded mount. The results clearly showed that the spiked arrays over-estimated the true ground vibration by 46.5 per cent on average, with a maximum observed error of 99.2 per cent. These errors are considered too large for compliance monitoring where accurate vibration levels are required for comparison with prescribed limits. Although spike coupling is convenient, its use for compliance monitoring should be viewed with caution. Unfortunately, however, many manufacturers supply their detectors as spiked arrays. A structural monitoring exercise was also carried out to evaluate the vibration response of a grain silo, highway bridge and a pit wall to the initiation of single blastholes. In this case accelerometers and standard geophones were firmly attached to the bridge which resonated at low frequencies. The results clearly show that, due to their limited low-frequency response, the geophones typically measured only half the true vibration level as measured by the accelerometers.

Jan 1, 1995

By Jena, Anand S, Das R. P

Leaching studies were carried out on Indian Ocean manganese nodules using sulphuric acid as the lixiviant. By leaching the nodules with 8 per cent sulphuric acid for 12h at 100°C, copper and nickel could be completely extracted along with 50 per cent cobalt and 6.2 per cent manganese.94.2 per cent of the iron was also dissolved. To increase manganese and cobalt extraction, charcoal was used as a reductant. The role of charcoal was to reduce the manganese dioxide and render it soluble as manganese sulphate as well as to facilitate solution of the cobalt minerals associated with the manganese dioxide. Various leaching parameters were studied including acid concentration, amount of reductant, leach time, pulp density and leach temperature. It was found that by leaching the nodules with 10 per cent sulphuric acid at 100°C for 4h using 5 wt/wt per cent charcoal (0.05g of charcoal per g of nodule) almost complete extraction of copper, nickel, cobalt and manganese could be achieved. However, under these conditions all the iron present in the nodules was also leached.

Jan 1, 1989

On Monday, October 25th, 1971 at approximately 12.15 a.m. the night shift proceeding underground discovered smoke at No.1 and No-3 cut throughs on the eastern side of the belt heading and in close proximity to the upcast shaft. Attempts to control the fire continued throughout the morning; as the position underground altered various procedures were adopted in an effort to contain and control the fire. Despite these efforts at approx. 12.40 p.m. a sudden change occurred which made it necessary to withdraw all workmen from underground, the vicinity of the Tunnel entrances and upcast shaft. Sealing of the mine at the entrances was the only remaining alternative. Several boreholes were put down to enable sampling of the atmosphere and air temperatures to be taken. This was essential as a guide to determining when conditions were suitable to allow exploration of the area using mine rescue self contained breathing apparatus.

Jan 1, 1972

By Stokes WPC

The capital requirements to develop a new mining venture are becoming very large; amounts of the order of US$1,000 million are not now unusual among estimates to bring new mining complexes into production. At the same time prevailing political and economic conditions are making it increasingly difficult to determine whether or not a project is likely to be viable. These factors emphasise the need to carry out thorough evaluation studies of all mineral prospects before making major investment. Additionally with the rapidly changing economic climate existing at the present time, it is becoming more and more necessary to carry out reappraisals of existing mines. An important function of both initial evaluations and reappraisals is to provide the operators of the mine with effective mining plans to ensure that the operation will meet its required economic targets. P, p M. tl p b, c v, s c 1 n 1 f r d c e c e u w Modern computers are well equipped to store and manipulate large amounts of data with speed and reliability. Their use in the mining field r is increasing and this trend serves to free f technical staff from much of the time consuming m and error prone hand calculations which were o formerly required in determining reserves and w carrying out all forms of mine planning. r Nevertheless, computers are not a universal

Jan 1, 1980

The Highlands Region of Papua New Guinea has 3 major national highways. The locations of these national highways are shown in Figure 1. The Highlands Highway begins at Lae City on the coast and passes through the Highlands towns of Goroka, Kundiawa and Mt Hagen. It terminates at Togoba approximately 10km out of Mt Hagen town. The Enga Highway begins at Togoba and passes through the towns of Wapenamanda, Wabag and Laiagam. It terminates at the giant Porgera Gold Mine. The Southern Highlands Highway also begins at Togoba and passes through the major towns of Mendi, and Tari. It terminates at Koroba station, near the Hides Gas Field. Two separate Feeder roads intersecting the main highway service both the Kutubu Oil Project and the Hides Gas Field. These national Highways play a very important role in the development of Papua New Guinea. Goods and services are delivered to the bulk of the population of the Highlands Region using these highways. Heavy machinery and equipment for the mining and petroleum projects of Porgera, Hides and Kutubu are transported using these roads.

Jan 1, 1997

Coal washing practice can be improved not only by critical examination of the plant being operated but also by studying plants operated in other areas. The developments at the Australian Iron & Steel Pty. Ltd. plants are discussed in relation to experiences there as well as developments which have taken place in Queensland in recent years. Early A.I.S. problems involved small coal cleaning in heavy medium cyclones and flotation. A proposed future plant flowsheet for A.I.S. is considered in the light of these experiences. Reference is made to plants operated by the Thiess, Peabody, Mitsui Coal Company Pty. Ltd. at Moura and the Utah Development Company's plants at Blackwater and Goonyella in the development of coal washing prac- tice in Australia.

Jan 1, 1975

Standards in the public reporting of resources and reserves in Australia have dramatically improved since the implementation of the Australasian Code for Reporting of Mineral Resources and Ore Reserves (The JORC Code) in 1989. Whilst the JORC Code states clearly that Mineral Resources and Ore Reserves are imprecise calculations and should be treated as estimates, there is strong evidence that many people regard them as fact, including some accountants, directors, auditors and investors. Mineral Resources and Ore Reserves are key inputs in the valuation of a mining company and the determination of financial performance. Geological knowledge is the foundation upon which Mineral Resources, Ore Reserves and investment decisions are made, however this information carries with it substantial uncertainty. Case studies and company reports have established that errors derived from inadequate geological inputs have led to reduced profitability in operating mines and in extreme cases the premature closure of mine operations. Whilst there are many causes of mine closure and reduced profitability, including commodity prices and exchange rates, the cumulative effect of all geological uncertainty contributes significantly to the erosion of the credibility of mining within the investment community. There are a number of methods used to characterise and model uncertainty in Mineral Resource and Ore Reserve estimation. Empirical mining indexes, sensitivity analyses, Monte Carlo simulations and Conditional simulations are used to identify and estimate geological uncertainty, notably the quantification of uncertainty in grade and tonnage estimates. These techniques have not generally been applied to estimating geological uncertainty associated with key Ore Reserve inputs such as appropriate mining technique, equipment selection, production rate, mining dilution, stability requirements, materials handling, metallurgical processing, product quality and waste storage. New software tools are needed to model the entire mining process with all its geological and other interdependencies, enabling all uncertainties to be separately identified and estimated. By its very nature, mining involves the assumption of significant technical, financial, political, environmental and social risk. Success comes by understanding and managing these risks and consequently the mining industry will never choose to reduce the level of geological uncertainty to nil. The ultimate aim of improved identification and estimation of geological uncertainty is to quantify inputs into the Ore Reserve process, allowing a company to assess the risks and manage these accordingly. This approach is relevant to feasibility studies for new projects as well as life-of-mine planning through to the weekly schedule at existing mines.

Jan 1, 2003

By A Morris

The Express Rail Link (XRL) will provide high-speed rail services from Hong Kong to Guangzhou and a connection to the national high-speed passenger rail network serving major cities throughout Mainland, China. The HK$ 67 B (NZ$ 11.5 Billion) project is of great strategic importance for Hong Kong and is being implemented to a very tight schedule, from early 2010 with completion targeted for 2015.The works include a 15 platform terminus station in West Kowloon, 26 km of twin track tunnels from the terminus to the Hong Kong/Shenzhen boundary at Mai Po, tunnel vent shafts/adits/emergency rescue siding and a stabling siding facility. Trains on the Hong Kong section are intended to operate at speed up to 200 km per hour and up to 350 km per hour on the Mainland section.This presentation will provide an overview of the entire XRL project, with a focus on the challenging geotechnical and spatial constraints on the tunnel works. This is an abstract only. No paper was prepared for this abstract.

Mar 8, 2011

By Kabel J. G

While a per onnel location system is primarily used to check that nobody is left in the mine at firing time, it is also useful for contacting people, uch a foremen, shiftbosses and tradesmen, who travel over several mine levels during a shift. The system installed at The Zinc Corporation, Limited, Broken Hill, uses punched coded plastic identity tags, with "In" and "Out" tag readers on each level. When entering a level, the employee inserts his tag in the "In" reader, and when leaving, in the "Out" reader. Each reader is connected to a central computer which shows who is still in the mine and their location.The system has been used on 3 levels by 21 men for a trial period of 4 months. It ha proved reliable in an underground mining environment, and employee acceptance has been good.

Jan 1, 1984

By Kazis JV

The beneficiation of fine coal has been the major problem facing the coal preparation engineer in recent years. The influence of clay slime, particle size and reagent type are but a few of the many factors that affect the recovery of fine coal. Laboratory test work has indicated that substantial increases in recovery could be achieved by improvements in technology in all these areas. Unfortunately, in most cases this technology has not carried through to the operating plants.

Jan 1, 1984