Search Documents

By L Mariano

Three selected iron ore samples from the major bedded and channel iron deposits of Western Australia were analysed using a scratch test commonly used in the oil and gas industry. The portable commercial equipment dubbed Wombat cuts a groove on the surface of the sample with a cutter under imposed depth of cut and cutting velocity. The normal and tangential components of the force acting on the cutter are recorded with a high degree of precision (about 1N) at fine spatial resolution of about 20 measurements per millimeter.The intrinsic specific energy inferred from the scratch test measurements is found very well correlated with a classical measure of strength such as the uniaxial compressive strength, for over 300 sedimentary rock samples.The results obtained on the iron ore samples are comparable to those obtained on oil and gas sedimentary rocks. This method could provide an objective and semi-automated measurement of material strength and brittleness in iron ores that can possibly be correlated to the lump to fines ratio.

Jul 11, 2011

By J M. Nel

Richards Bay Minerals (RBM) has recently undertaken an exercise to improve orebody basal definition. Older mineralisation bases (pre-2005) were highly erratic using old protocol reverse circulation (RC) (also known as Air Core) drilling and interpretation. The erratic nature of this estimation tool, resulted in impractical modelling towards the end of mineralisation (EOM), difficult mine design and unrealistic reconciliation. New protocol drilling, which includes high definition SONIC drilling data, has provided more data to be available for more accurate interpretation. Recent advances in drilling methodology has allowed for better penetration depths for SONIC drilling, which was previously restricted to approximately 80 m (pre-2005). This improved data set allows more emphasis on geological interpretation with factors such as lithology, slime content, and mineral species distribution. These factors when in unique combination enable more accurate and realistic EOM data points. These points are modelled into surfaces using conditional simulation techniques and result in a vastly smoother surface and consequently, a more representative resource.

Oct 5, 2011

By P Guj, J A. Bell

The valuation of early-stage exploration projects requires a valuer to take into account a large number of uncertain value drivers, the interplay among which may be non-linear. This paper examines some of the key value drivers including geology, target metrics, project area and maturity, the market and the psychology behind the decision-making process. The commonly accepted valuation methods and their underlying logic are outlined, including a view on why they evolved, what value drivers they attempt to address and their potential shortcomings. These methods include the multiple of exploration expenditure, geoscience rating, expected values and market based methods. The potential future valuation methods of replacement values and neural networks are also introduced along with how to minimise heuristic bias and error within the market-based approach.CITATION:Bell, J A and Guj, P, 2012. Exploration value drivers and methodologies, in Proceedings Project Evaluation 2012 , pp 17-28 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By M J. Nimmo

extremely powerful tools for building predictive and generative models. ML can be used for building highly accurate regression and classification models. But without careful data science and statistical analysis, a regression or classification model could be highly biased and completely wrong – and we may not even realise. An example rock density estimation task will be used to illustrate the potential gains and possible pitfalls in using ML and AI in Mineral Resource estimation. What could possibly go wrong? Nothing! For most simple regression or classification problems, very little. For density estimation, using the global mean may be all that is possible, but the resource classification would need to reflect the uncertainty in global estimation of tonnage. Everything! From data collection and measurement, from selecting ML and AI techniques and designing the analysis workflow to our own cognitive bias. The things that could go wrong are vast and may include but not limited to asking the wrong question, not asking questions, data bias, measurement errors, insufficient data coverage, not collecting the right variables, not collecting enough observations, collecting clustered samples, unbalanced data, filtering out data without reason (outliers), clipping data (outliers), relying on automatic feature selection, including irrelevant variables, excluding relevant variables, geological interpretation, changing context, blindly following best practice, splitting small data sets, subsetting large data sets, using the wrong tool for the task, insufficient budget to complete the analysis, not allowing enough time for testing and experimentation (the science), focusing too much on building the model (the engineering), not learning from the data, our assumptions, our preconceptions, and our skill. This paper will explore the question of how training regression models to predict rock density are affected by gaps in the data (missing observations and missing variables). What could possibly go wrong?

May 24, 2023

Resue or split face firing has the potential to separate ore and waste rock into separate muck piles within a stope. Thus split face firing has the potential to reduce dilution of the ore stream to be transported to the surface for subsequent processing. It also potentially reduces the total amount of broken rock needing to be transported out of the mine as the waste material is physically separated from the ore as part of the blasting process. Waste can therefore be used directly from the stope to backfi ll other mining areas. This paper reports on the results of split face firing trials at the Hillgrove mine in NSW and analyses the results of these blasts.

Aug 1, 2010

By I D. Gregson, A S. Garcia, K M. MacAndrew

The design work undertaken by Rock Mechanics Technology (now part of Golder Associates (Golder)) has played a major part in successfully establishing mechanised room and pillar working in Indian coalmines, both for the development of new districts and for the re-establishment of old districts prior to pillar extraction on panel retreat.Golder has used appropriate design of pillars, extraction sequences and final snook sizes to minimise ground control risks during pillar extraction. Where the strata will not cave reliably, partial extraction systems leaving either a crush pillar or a substantial yield pillar have been adopted.Remote monitoring of selected pillars during the extraction process using stress cells, extensometry and convergence measurements provides confirmation of pillar behaviour and verification of designs.A new telltale device, giving a visible warning of impending caving, is now installed at all Indian pillar extraction sites and is proving very successful.CITATION:MacAndrew, K M, Garcia, A S and Gregson, I D, 2014. Coalmine pillar design and performance during mechanised pillar extraction in India, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 347–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By J Penman, N Turner, H Liu

This paper aims to present a snapshot of the risk profile for tailings storage facilities within Western Australia by comparing the spatial distribution of known facilities against common geohazards such as cyclonic activity, climate, and peak ground accelerations from earthquakes. The analysis also includes an assessment of proximity to populations at risk including towns and sensitive receptors including significant river systems and wetlands.

Jul 1, 2021

By D Kepert

It is the role of the exploration geologist to create wealth through the discovery, delineation and characterisation of economic mineralisation. This requires a critical depth of geological understanding.Unfortunately, the resource industry is well known for its cyclic nature. Many of the current generation of workers have only ever experienced the boom of the ‘super-cycle’ and are only just discovering the negative side to the business. For the case of the geologist and especially the exploration geologist, the magnitude of peaks and troughs are usually amplified and may become destructive to all parties. During the uptime a healthy stream of exploration good news becomes the staple diet of company releases, in particular those of junior companies attempting to bolster the share price. The geological knowledge and experience gained thus forms a significant and integral part of the value and therefore, future of a company. On the downturn it is often viewed that geologists are a luxury, an optional extra and a burden on the bottom line with companies entering a period of memory loss and myopia.Retention of geological knowledge however remains critical as projects, companies and cycles mature. Beyond exploration per se, this knowledge becomes both fundamental in de-risking and commercialising an asset (through development or divestment) and in positioning the company for cyclic or counter-cyclic opportunities.The growth and retention of this knowledge base is difficult to quantify in terms of direct value but becomes one of a successful resource companies greatest assets. At worst, its loss can lead to millions of investors’ funds wasted on missed opportunities, drilling, or poorly designed plant and mine.But the rocks are around for the longer haul and pay little notice to the vagaries of the scurrying of Man.This paper reflects on some of the authors own observations through 25 years of iron ore exploration, in why it is critical to always rigorously question the prevailing geological (mis)understanding and the technical and commercial benefits which that may bring, and looks forward to the future.CITATION:Kepert, D, 2015. Geology – the affirmative case, in Proceedings Iron Ore 2015, pp 285–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By T Huynh, K Tungpalan, E Wightman, M Edraki, S Palaniandy

Most preventive environmental management practices promote proactive integrated approaches to waste management. For example, life cycle assessment is often used to find the ‘hot spots’ of environmental burdens. This kind of approach is often based on generic data and has rarely been used for tailings. Besides, life cycle assessments are less useful for designing operations or simulating changes in the process and consequent environmental outcomes. It is evident that an integrated approach for tailings research linked to better processing options is needed.The aim of this Nextmine™ project is to develop new tailings management models by streamlining orebody characterisation, process optimisation and rehabilitation. We present an integrated tailings management approach and preliminary results from a case study. Combined grinding and flotation models were developed using geometallurgical data from the orebody, to predict the properties of tailings produced under various processing conditions. The modelling scenarios based on the case study data provide the capacity to predict the composition of tailings and the resulting environmental management implications. For example, the type and content of clay minerals in tailings will affect the geotechnical stability and water recovery. Clay content will also influence decisions made for paste or thickened tailings and underground backfilling.CITATION:Edraki, M, Huynh, T, Wightman, E, Tungpalan, K and Palaniandy, S, 2015. An integrated approach to proactive tailings management, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 323–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Grano S. R, Lauder D. W

Investigations on the oxidation behaviour of chalcocite and its rejuvenation by hydrogen sulphide ion have been undertaken. Chalcocite oxidation was measured using X-ray photoelectron spectroscopy (XPS), zeta-potential and by dissolution in et

Jan 1, 1997

By W P. Darcey

Jabiru Metals completed a feasibility study on the Jaguar Base Metal Project in July 2005. The study was based on conventional truck haulage via a decline. Conveyor haulage was considered but not in sufficient detail to provide a meaningful comparison. The current study investigates the cost and productivity of alternative ore transport systems for the Jaguar project. The options considered are conventional underground truck, conveyor, road train, rigid frame truck, monorail haulage and shaft hoisting. Shaft hoisting was not considered in detail due to the high capital outlay for such a relatively short mine life of less than six years. This study goes beyond the common approach of evaluating haulage systems in isolation; it includes development costs, timing of ore production and costs associated with mine services as well as administration and milling costs. The results of this study indicate that the best haulage option for the Jaguar project is conventional truck using the Hitachi AH400 trucks. The net present value (NPV) for this option is A$8.13 million higher than the next best option namely the Kiruna E635 electric truck. The conveyor option has the lowest operating cost per tonne of ore but the longer development time negatively impacts on its NPV. The monorail option is considered impractical due to the number and length of trains required to achieve production targets.

Mar 21, 2011

By Bhattacharyya A. K>

The Pemali Open Pit Mine is situated in a small island called Bangka in Indonesia. It produces approximately 165,000 m3/year of tin ore with an average grade of 3.67 kg/m' of tin from a primary deposit. The deposit occurs at the rim of a granitoid intrusion within sedimentary beds. The rock formations, all extremely weathered, and the overlying alluvium, are exposed to a rainfall exceeding 3m/year. Serious slope stability problems are experienced at the mine, despite using overall pit slopes of 20¦-29¦, the latter resulting in a stripping ratio of 4:1. This paper outlines a computer based back analysis of a major slope failure involving some 250,000 m' of material which occurred on the west wall of the pit in February, 1984. The findings from the analysis, together with other information, are used to examine the stability of the east wall of the pit, where tension cracks developed later. The results indicate that the large influx of water was the most significant cause of such slope stability problems and a more intensified water management programme would be beneficial.

Jan 1, 1989

By A K. Raina, V M. S R Murthy

Rock mass response in blasting is an important element to determine the performance of a blast along with its other outcomes. The near-field monitoring for rock mass response analysis is vital for determining the behaviour of a blast; however, due to costly and cumbersome methods involved in such measurements the subject has received scant attention so far and the publications on this account are perfunctory in nature. This paper presents a non-destructive method to monitor the blast-induced pressure in the rock mass at a distance from a blasthole. The methodology of monitoring and a few examples of actual field monitoring are detailed in this paper. The responses of the rock in the near-field of a blasthole under dynamic loading have been documented to predict fragmentation and throw. The proposed method has also been used in limited cases earlier by the author to predict flyrock using a semi-empirical method and trajectory equation. The pros and cons of the method are discussed while throwing light on the actual response and the prediction of fragmentation and throw of blasted rock.CITATION:Raina, A K and Murthy, V M S R, 2015. Measurement of blast-induced pressure in bench blasting and deciphering explosive performance through rock mass response analysis – a methodology, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 501–508 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Mather, H R. Asche

"In the civil tunnelling field, the use of tunnel boring machines (TBM) has now overtaken the use of conventional excavation methods (drill and blast / roadheader). This is due to a number of reasons, including the increasing availability and reliability of TBMs, the ability to deal with a wider range of face conditions, and the reduced excavation cost that TBMs can bring.Mining companies have spearheaded the advances in shaft boring by mechanised means, both in blind and raise boring. However, mining companies have been slower to adopt mechanised tunnelling.When contrasted with a conventional mining contract, there are good reasons why TBMs in mining applications are relatively rare. A conventional decline contract may have very little geotechnical information. The decline alignment can be subject to change as the tunnelling progresses. The infrastructure requirements are less for a conventional decline, and the sunk cost prior to excavation commencing is lower. Contract documents can be very simple.The history of TBM use in mining is reviewed and lessons are described. From the case histories and lessons learnt, the paper identifies ways that mining companies can maximise the potential benefit of TBM technology.We believe that despite the additional requirements for TBM declines, the cost and time advantage to mining companies is very attractive. The challenge is to recognise and to meet the requirements for success in a TBM drive to achieve the advantages of: faster advance rates reduced rock damage/overbreak reduced support requirements uniform muck characteristics greater personnel safety.From the case histories and lessons learnt, the paper identifies ways that mining companies can maximise the potential benefit of TBM technology.CITATION:Asche, H R and Mather, D, 2014. Use of ?tunnel boring machines in the mine environment, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 655–662 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 17, 2014

The issue of retrenchment is a topic of considerable relevance for the Papua New Guinea (PNG) mining, petroleum and gas industries. The unique environments in which Porgera Joint Venture (PJV) and other similar operations operate are likely to confront these industries with particular dilemmas that will require a range of investments to mitigate the problems associated with retrenchment and employment. This paper discusses retrenchment and employment in the PNG mining industry using the specific case study of PJV. The paper deals with the issue of employment and retrenchment of local workforces in the PNG context, which presents a serious challenge for the resources industry and the achievement of sustainable development objectives. The issue of future retrenchment of the workforce as a result of mine closure is an obvious challenge for both PJV and the Porgeran community at large, who have now come to rely upon both the employment opportunities presented through the mining. This paper examines these challenges and in doing so highlights some progress made by PJV. The paper also discusses downsizing, strategic practices and holistic approaches of retrenchment and employment. In doing so the paper highlights issues that have been overlooked in both academic and applied studies from global and local perspectives in the PNG mining sector. The latter sections articulate the relevance of the information provided by the case study in the wider context of retrenchment. The conclusion promotes a perspective that a great deal more investment will be required by all stakeholders to respond to the challenges of managing retrenchments and mine closure.

Jan 1, 2009

By E Jak, M Shevchenko, E Nekhoroshev, D Shishin

In the field of pyrometallurgy, the presence of multiple molten phases with distinct chemical compositions, such as slags, mattes, speiss liquids, metals and molten salts, is a well-known phenomenon. These phases exhibit strongly non-ideal solution behaviour and are mutually miscible to varying degrees. To describe these complex molten liquids, the Modified Quasichemical Model (MQM) has proven effective and has been applied to numerous binary, ternary and several higher-order multicomponent systems related to pyrometallurgy. In recent decades, the complexity of high-temperature processes has escalated due to increased impurity concentrations in primary ores, the incorporation of recycled consumer products and the integration of metallurgical plants through by-product and waste exchanges. To address these issues, PYROSEARCH laboratory has been developing large 20-component thermodynamic database using a generalised CALPHAD (CALculation of PHAse Diagrams) methodology integrated with experimental investigations. Over the past decade, strategic decisions were made balancing the ability to generate experimental data, prediction power, accuracy, stability of calculations, as well as computational time, which are discussed in the paper. Examples provided for issues of >3 liquid immiscibility, non-ionic behaviour and exaggerated ‘sharp’ enthalpies of mixing in silicate slags, dealing with multiple oxidation states, as well as comparative analysis of pair and quadruplet approximation in MQM.

Aug 21, 2024

By Duke J. H

Advanced computer aided geological modelling techniques are now available to the geologist to allow the rapid evaluation of a gold orebody at various stages of its development. The types of grade estimation techniques used change during the various stages as the density of drilling and knowledge of the deposit increases. At the prospect evaluation stage drillhole intercept selection techniques are coupled with preliminary 2D (vein or layer) modelling or 3D block modelling techniques to arrive at a geological resource estimate. At the prefeasibility and feasibility stages more sophisticated 2D and 3D modelling techniques, such as domain controlled grade interpolation with anisotropy, are used along with interactive open pit and underground mine design, to calculate recoverable reserves. At the production stage closely spaced blasthole sample data is modelled quickly and coupled with interactive grade control facilities. Shot volumes, tonnages and grade estimates can be databased to provide reconciliation figures. These modelling techniques are embodied in MINEX-3D, an Australian software system which, with the emergence of the 386-based PC and high resolution (VGA or better) graphics, makes a whole range of advanced geological modelling techniques available to most exploration and mine geologists.

Jan 1, 1989

By J Sigda, T Jones, D Staggs, J Ewing, C Cheng, J Pickens, S Paulka

Mine-derived solutes from Energy Resources of Australia’s (ERA’s) Ranger uranium mine have been closely monitored for decades. Ranger is surrounded by the Northern Territory’s Kakadu National Park and is upstream of Ramsar convention wetlands. Modelling of groundwater flow and solute egress from mine wastes to surface waters has helped ERA successfully assess closure options and secure intermediate regulatory approvals during the site closure process. Potential environmental impacts were assessed using groundwater modelling in support of three ERA applications involving disposal of tailings-derived mine waste. Model results were an important part of the basis for obtaining regulatory approval. Three case studies are presented describing the three applications and how the groundwater modelling supported approval of the applications. For case study #1, INTERA supported ERA in addressing stakeholder concerns in 2017 regarding two aspects of tailings deposition in Pit 3. The first was the potential for flow of tailings fluid into the surrounding formations during tailings deposition. The second was the difference in post-closure magnesium (Mg) loading to surface water for two tailings deposition scenarios. INTERA developed a two-dimensional (2D) model that showed excess tailings pore pressures would not cause outflow and solute egress from the pit during deposition. INTERA’s three-dimensional (3D) models demonstrated that post-closure Mg loading to creeks for both tailings scenarios differed marginally and would be a small fraction of natural creek Mg loads. The modelling results helped avoid delays in completing tailings deposition driven by stakeholders’ environmental concerns. Case study #2 consisted of supporting ERA’s 2019 request for approval to change the tailings deposition method and final tailings level in Pit 3. INTERA’s model results for the permitted and proposed deposition methods showed minimal differences in post-closure Mg loading to creeks. The model results helped ERA obtain the needed approval for the tailings deposition method and water and tailings levels in Pit 3. For case study #3, INTERA modelled the comparative impacts from leaving the entire contaminant plume from the temporary tailings storage facility (TSF) in situ or excavating a portion of the contaminated material from beneath the TSF floor and placing it in Pit 3. The modelling results supported an approved TSF contaminated material application important for ERA to stay on schedule and minimise both closure costs and environmental impacts.

Jul 1, 2021

By T Berryman, C Adams, L Griesel, C Buxton

The Kalgoorlie Consolidated Gold Mines (KCGM) schedule model is used for short- to medium-term planning and scheduling at the Fimiston Open Pit Mine (the Superpit). The model bridges the gap between grade control models, which are generated one to seven days prior to mining, and the annual Resource and Reserve model update that is used for budget and life-of-mine plans. The schedule model uses close-spaced grade control data (up to 20 000 m drilled each month) as well as resource definition drilling to estimate production volumes three to six months ahead of current mining. From this, a rolling 12 week mining and processing schedule is generated on a monthly basis. As the KCGM operation is mill and sulfur constrained, the schedule model needs to be an accurate predictor of ounces as well as tonnes, gold and sulfur grades. The process must also be time efficient in order to meet monthly planning and reporting deadlines. Due to the large amount of new data generated each month, model updates using conventional interpretation and estimation techniques have proven to be impractical and too time consuming. This paper will examine the evolution of the Superpit schedule model process over time, recent improvements and the effect of different model outcomes on short- and medium-term mine planning.CITATION:Griesel, L, Buxton, C, Adams, C and Berryman, T, 2014. The superpit schedule model – A time-efficient data-driven estimation for short- and medium-term planning, in Proceedings Ninth International Mining Geology Conference 2014 , pp 397–410 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By H Wright

Black Rock Cave (BRC) is a sublevel cave which was developed in 2018–2020 and has been in production since November 2020. BRC is part of the Mount Isa Mines complex and extracts a leached orebody comprising of high-grade chalcocite ore, situated below the historic Black Rock Open Cut workings. The mine is owned by Mount Isa Mines and operated under contract with PYBAR Mining Services. In 2021 a number of rockfalls occurred throughout the mine and were increasing in frequency. This culminated in a major rockfall on the decline in June 2021, after which the decision was made to withdraw all persons from the mine, initiate rehabilitation and conduct further investigations to deduce a safe method to provide long-term support. The rockfall investigations have shown that the corrosive nature of the highly leached rock mass can consume a split set in less than 18 months. A review of potential corrosion resistant ground support methods concluded that steel split sets have a safe lifespan of six months at BRC, and that all workings must have corrosion resistant support installed prior to exceeding the safe life of the friction bolts. The review recommended the use of 4 m cable bolts as the most suitable method of corrosion resistant support. This new support system, and the requirement to rehabilitate all mine workings within the leached orebody, had an impact to the schedule and an effect on both equipment and manning levels at BRC. Accelerated jumbo rehab allowed access to the production levels within two months of the rockfall. Cable bolting then followed the jumbo bolting in all leached areas. The direct impact has been ten months of reduced production, due to night shift closures of the decline to enable cable bolting. The impact to the mine has been minimised by the small flexible team that enabled the mine plan to change rapidly and often to accommodate the challenging conditions. In less than two months from the rockfall event, production had resumed. Within ten months of concluding that the mine required; full rehabilitation, a new support system and a full re-schedule, normal mining operations had restarted, with pre-event productions rates being achieved.

Mar 29, 2023