Search Documents

By David B. Burrows, Rlkl Kobayashi, Norman L. Carr

The viscosity of hydrocarbon mixtures, whether in the gas or liquid phase, is a function of pressure, temperature, and phase composition. This paper presents methods for the prediction of the viscosity of the gas or less dense fluid phase over the practical range of pressure, temperature, and phase compositions encountered in surface and subsurface petroleum production operations. The correlation necessary to predict the effect of pressure on viscosities is presented in Part I. Serious discrepancies in high pressure gas viscosity data in the literature are discussed. The application of the correlation to predict absolute viscosities is discussed in Part 11. Auxiliary correlations are presented to enable calculations of viscosities from a knowledge of the pressure, temperature, and gravity of the gas phase. INTRODUCTION A knowledge of the viscosity of hydrocarbon fluids is needed to study the dynamical or flow behavior of these mixtures through pipes, porous media, or more generally wherever transport of momentum occurs in fluid motion. Since flow is predominantly in the laminar region in petroleum reservoirs, the influence of fluid viscosity on this flow is especially important. As early as 1894, Onnes1 and Onnes and de Haas' noted that the viscosities of homologs under corresponding states could be correlated. The theorem of corresponding states has been further developed and applied to the viscosity of pure, nonpolar gases under pressure by Comings, Mayland, and Egly.3 It was demonstrated that the viscosity ratio could be expressed rather closely as a function of reduced pressures and temperatures, 1.e.: µ/µ1 = f( TR2 PR) ........(1) temperature, absolute units where: TR =------------------------------ ------ critical temperature. absolute units _pressure, absolute units critical pressure, absolute units µ = viscosity of gas at reduced temperature TR and reduced pressure PR µ1 =. viscosity of gas at atmospheric pressure and at temperature TR Serious discrepancies in the viscosity of pure hydrocarbon gases at high pressures have been called to Our attention by Comings, and and Egly. They made a careful analysis of the following methods commonly used to measure gas viscosities: 1. Oscillating disc viscometer4,5 2. Rolling ball viscometer6,7 3. Capillary tube viscometer12 On the basis of their analysis of the problem and their experimental data on the viscosities of methane, ethylene, carbon dioxide, and propane, they preferentially selected data obtained by the capillary tube viscometer to develop their viscosity correlation. Since then a need has existed to verify the experimental technique of Comings, Mayland, and Egly for the determination of viscosities at high pressure; to extend the data to mixtures of hydrocarbons; and to extend the range of their correlation to include higher pressures. Using the correlation procedure of Comings, May-land, and Egly, the prediction of gas viscosities is resolved into the correlation of the effect of pressure, temperature, and composition on the viscosity of hydrocarbons and their mixtures and the prediction of viscosities of mixtures of hydrocarbons and other natural gas components at one atmosphere pressure.

Jan 1, 1955

By Philip E. LaMoreaux

Fluoride, generally less than 0.5 ppm, is present in ground water from rocks of Paleozoic age and older, in northern and eastern Alabama. Some of the water-bearing formations in the Coastal Plain area of the State yield water with as much as 6.8 ppm fluoride.

Jan 8, 1950

By A. E. Gorum, J. Washburn, E. R. Parker

Experimental evidence was obtained in support of the idea that cleavage fracture can be initiated by dislocation pile-up. The high ductility of MgO crystals when tested in bending comPared to their relative brittleness in tension was explained on the basis that large pile-ups are more likely in a tension specimen. CLEAVAGE fractures have been a problem of major concern for many years. A number of large steel structures have failed in a brittle manner, usually suddenly and without warning; often the failures occurred for no obvious reason and at nominal stress levels well within the generally accepted range. A great deal of data have been collected about factors that contribute to failures,1 but the physics of the fracture process has never been revealed. cottrel12 has recently developed a theory of brittle fracture in ductile materials which was based upon the concept that dislocations moving on two intersecting planes can unite to form a crack nucleus. This theory accounts for the known effect of grain size and for the effect of testing temperature. There has, as yet, been no experimental evidence published that would substantiate this or the earlier theories based on stress concentrations due to piled-up dislocations. The study reported herein was conducted to obtain information that would either substantiate or disprove the

Jan 1, 1960

By E. S. Machlin, C. W. Chen

THIS investigation is concerned with the origin of the intercrystalline voids and cracks formed in metals and alloys subjected to stress at elevated temperature. There have been many suggestions in the recent literature relating to this problem. Greenwood' suggested that the voids may be produced by vacancy condensation. Zener has stated that shear-stress relaxation across grain boundaries could initiate high tensile stresses at the regions blocking grain boundary slip and thereby cause the formation of cracks. Chang and Grant3 have described the formation of cracks at grain boundary triple points and have experimentally verified Zener's mechanism for the grain boundary regions in the vicinity of a triple point. Subsequent to the completion of this investigation, Gifkins4 developed a model which made use of Stroh's5 mechanism of fracturing to produce sub-microscopic fractures that subsequently grow by grain boundary slip. Chen and Machlin,6 in answer to Gifkins, described a model deduced from the present investigation, in which grain boundary slip provides both the stress to fracture at grain boundary jogs and the deformation required to separate fractured jog surfaces. The possibility of gas condensation to form intercrystalline voids and cracks is eliminated as a basic mechanism because such voids and cracks are developed in vacuum melted material containing minute amounts, if any, of gaseous impurities. In a theoretical evaluation of this problem, Machlin7 concluded that void nucleation by vacancy condensation during creep-rupture is improbable but that vacancy condensation on supercritical sized voids to produce growth is probable. This investigation was begun to evaluate the suggested mechanisms for intercrystalline fracture. In particular, in order to correlate vacancy supersaturation ratios produced in creep with those determined by Bal-luffi and Seigle8 as critical for , the nucleation of voids, specimens were obtained from the same heat of brass as used by the latter authors, through the courtesy of Dr. Seigle. The experiments conducted in this investigation fall into the following categories: 1) Brass—observation of voids produced under a variety of conditions, including creep under compression, to evaluate the mechanisms of void nucleation and growth. 2) Bicrystal experiments to check the mechanism of void nucleation deduced in this investigation. 3) Morphology of intercrystalline voids produced in a variety of metals. Each set of experiments will be described and discussed separately. Experimental Techniques A special creep-rupture test rack was constructed which made it possible to apply the stress to the specimen in a controlled atmosphere of inert gas, reducing gas, or vacuum. All the creep-rupture tests on a-brass (30 pct Zn) were conducted in nitrogen under a pressure slightly above atmospheric. Either dead weight loading or constant elongation rate loading could be applied with the load measured by means of a strain gage dynamometer. In order to obtain a coarse-grained crystal structure stable at

Jan 1, 1958

By Paul C. Merritt

Chrysotile asbestos producers in Quebec may soon experience a unique situation-i.e., strong competition from American ore sources for the short fiber market west of the Mississippi River. This com- petition will be forthcoming from Copperopolis and Coalinga, two deposits now being developed on opposite flanks of the San Joaquin Valley in central California. The combined output now planned from both deposits is 100,000 tons annually, equivalent to about 50% of the annual market demand in the western, central and Gulf States, and more than twice the tonnage sold in 1960 by all other American asbestos producers combined. The principal companies involved in these new undertakings are Jefferson Lake Asbestos Corp. (subsidiary of Jefferson Lake Sulphur Co.), Hidden Splendor Mining Co., Coalinga Asbestos Co. (Johns- Manville Corp. in conjunction with Kern County Land Co.), Union Carbide Corp., and Asbestos Corp. Ltd. Jefferson Lake's principal interest is at Copperopolis where the company's new 70,000-ton per yr mill recently went on stream. The company also holds some claims at Coalinga, but this latter area is better known as the site where Hidden Splendor, Coalinga Asbestos Co. and Todd Industries (a local company) have established operating mines and mills capable of turning out 30,000 tons of fiber each year. Coalinga is also the site of exploration by Union Carbide Nuclear and Asbestos Corp. Ltd.

Jan 9, 1962

By C. E. Webber

The economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro- carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,~ who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40' to zoo°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33' to r8oUF. and from 100 to 5000 lb. per sq. inch. Materials The absorber oil was a typical naturally occurring, Straw-colored distillate that had previously been steam-distilled to an initial boiling point of 300 F. The physical and chemical properties, including the results of an Engler distillation, are presented in Table I. A large volume of this oil was obtained and it was used throughout the complete set of experiments. Table i.—Properties of the Absorption Oil Gravity .......................... . . 32.5' A.P.1. Molecular weight by benzene freezing- point depression.................. 183 Viscosity, poises; at 100°F........... 0.0a80 At 200°F...................... 0.0102 Composition, PeR Cent Aromatics........ 24.0 Naphthenes..... 36.7 unsaturates,Aromatics...... .I24.00.3 1 Parafins Naphthenes.....36.7 39.o EngLeR Distillation Per Cent /ncg. F. Per Cent Dez. P. Initial boilins rmint.. 300 I 60....... 523 5.................. 402 I 70....... 538 10.................. 421 180....... 557 20.................. 462 90....... 570 30.................. 480 1 95....... 623 40.................. 49 .................1 511 Residue, z .o per cent; loss, 0.3 per cent. See refrence I. The n-hexane was obtained from the Ohio Chemical and Manufacturing Co., Cleveland, Ohio. This liquid had a boiling range of from 149" to 152.6'F., with a density of 0.667 at 60°F. and a molecular weight of 85 by benzene freezing-point depression. The propane, isobutane, wbu-tane, isopentane and n-pentane were ob-ta,ined from the Philgas Department of the Phillips Petroleum Co. Certified analyses of these compounds showed their purity to be in excess of 99.5 per cent and they were riot further purified.

Jan 1, 1941

By C. E. Webber

The economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro- carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,~ who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40' to zoo°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33' to r8oUF. and from 100 to 5000 lb. per sq. inch. Materials The absorber oil was a typical naturally occurring, Straw-colored distillate that had previously been steam-distilled to an initial boiling point of 300 F. The physical and chemical properties, including the results of an Engler distillation, are presented in Table I. A large volume of this oil was obtained and it was used throughout the complete set of experiments. Table i.—Properties of the Absorption Oil Gravity .......................... . . 32.5' A.P.1. Molecular weight by benzene freezing- point depression.................. 183 Viscosity, poises; at 100°F........... 0.0a80 At 200°F...................... 0.0102 Composition, PeR Cent Aromatics........ 24.0 Naphthenes..... 36.7 unsaturates,Aromatics...... .I24.00.3 1 Parafins Naphthenes.....36.7 39.o EngLeR Distillation Per Cent /ncg. F. Per Cent Dez. P. Initial boilins rmint.. 300 I 60....... 523 5.................. 402 I 70....... 538 10.................. 421 180....... 557 20.................. 462 90....... 570 30.................. 480 1 95....... 623 40.................. 49 .................1 511 Residue, z .o per cent; loss, 0.3 per cent. See refrence I. The n-hexane was obtained from the Ohio Chemical and Manufacturing Co., Cleveland, Ohio. This liquid had a boiling range of from 149" to 152.6'F., with a density of 0.667 at 60°F. and a molecular weight of 85 by benzene freezing-point depression. The propane, isobutane, wbu-tane, isopentane and n-pentane were ob-ta,ined from the Philgas Department of the Phillips Petroleum Co. Certified analyses of these compounds showed their purity to be in excess of 99.5 per cent and they were riot further purified.

Jan 1, 1941

By E. H. Rennhack, J. F. Libsch

Definite transition behavior was found in unalloyed titanium at 0.13 pct 0 equivalent. The addition of 0.5 Sn, 1.0 Al, 0.5 Al, and 1.0 Sn lowers the tvansition temperature of titanium at oxygen equivalents exceeding 0.22, 0.29, 0.40, and 0.51, respectively. Metallographic evidence indicates that progressive amounts of oxygen restrict deformation at low temperatures resulting eventually in brittle fracture. The presence of tin or aluminum is thought to alter the atomic distribution of oxygen within the titanium lattice in such a manner as to facilitate some degree of slip and twinning. 1 ITANIUM-like iron and zinc experiences a transition from ductile to brittle fracture with decreasing temperature. The presence of sufficient quantities of the interstitial elements, carbon, oxygen, and nitrogen in solid solution, has been shown to progressively lower the room-temperature impact resistance of titanium with increasing interstitial content.1"1 Ogden,et al,2 reported finding no transition from ductile to brittle fracture with decreasing temperature in iodide titanium. However, a definite transition was found to occur at 0.36 pct 0 equivalent in an alloy containing 0.47 pct carbon in solid solution. The oxygen equivalent in this case was obtained by assuming the effects of carbon, oxygen, and nitrogen in combination on the impact properties of titanium to be additive on the same basis as their separate effects on tensile strength, namely: Oe = 2/3 (pct C) + pet 0 + 2 (pet N) They concluded that the tendency toward transition behavior is dependent on the total interstitial content in solid solution and not on any one particular interstitial element. Rennhack,4 however, recently found transition behavior in iodide titanium at an oxygen equivalent of 0.17 pct. Ogden, etal3, reported that the strengthening effects of carbon, oxygen, and nitrogen in titanium decrease with the addition of tin. They showed that tin additions increase the tolerance of titanium for the interstitials, that is, 10 pct Sn permitted individual additions of up to 0.4 wt pct of the interstitial elements without any significant loss in ductility. Aluminum tends to decrease ductility and impact strength of titanium for a given interstitial ~ontent.3 Van Thyne and Kessler5 found that the solid solubility of carbon in titanium doubled in the presence of 10 pct Al. The precise effects of tin and aluminum in the nrespncp of rorvfen nn the impact properties of titanium had previously not been determined. The high oxygen tolerance of titanium containing tin may provide a suitable means for improving the impact properties of titanium containing the interstitial elements, particularly oxygen. Unlike tin, however, aluminum has a high affinity for oxygen and will reduce rutile titanium dioxide (TiO2)by a thermit-type reaction.6 Thus, the atomic distribution of oxygen in titanium might be different in the presence of aluminum. The present work was undertaken to: 1) Determine the effect of oxygen on the transition behavior of unalloyed iodide titanium. 2) Determine the effect of small amounts of tin and aluminum on the transition behavior of iodide titanium in the presence of oxygen and other interstitial~. EXPERIMENTAL Three different lots of iodide titanium were employed to prepare the alloys studied in the present work. Their chemical composition is presented in Table I. The compositions of the tin and aluminum used for alloying are shown in Table 11. Oxygen additions were made using calcined rutile titanium dioxide (TiO2)of 99.7 pct purity. Alloy Preparation—Four titanium-base alloys containing separate additions of 0.5 and 1.0 pct each

Jan 1, 1960

By Elmer A. Jones

Development work in mines of St. Joseph Lead Co., Southeast Missouri, using trackless loading equipment shows definite advantages: Speed of cleaning, ability to work on steep grades and sharp crosscuts, good later tracking conditions, and possibility of wasting rock in old abandoned stopes.

Jan 6, 1950

By M. D. Everell

A study has been made of the relationships between grinding selection functions and physical properties of rocks, particularly the failure loads of irregular particles and the compressive and tensile strengths of large regular specimens. The rocks used were limestones of various structures and impurity contents, a carbonatite, and a high-purity crystallized calcite. The selection functions were obtained from carefully performed grinding experiments on selected narrow size ranges in various grinding machines-a laboratory batch ball mill, a Hard grove grindability machine, and a mill of the type suggested by Yang, Mempel, and Fuerstenau. The specific rates of breakage during milling and the failure loads of irregular specimens correlated well for the rocks studied. The testing of irregular particles is suggested as a means of predicting the behavior of commercial mills.

Jan 1, 1973

By A. J. Phillips, A. A. Smith, J. S. Smart

THE preparation of a sufficient quantity of high-purity copper for extensive laboratory use in the study of impurity effects has been an integral part of a research program in progress at the Central Research Laboratory of the American Smelting and Refining Co. for the past several years. Initially the degree of purity desired was that necessary to meet two essential requirements for experimental accuracy: (I) no impurity was to be present in the copper in an amount capable of producing a detectable effect on the properties to be studied, (2) even the minor changes in properties caused by the addition of extremely small amounts of individual elements were to be measured without significant interference from contaminants. In the course of the investigation, evidence has accumulated to justify the conclusion that this copper is of exceptional purity; in fact, no impurity can be detected by any chemical method or spectrographic technique known to the authors. The present paper describes the method of production of the copper and presents some of its properties. PREPARATION OF HIGH-PURITY COPPER The elimination of impurities from commercial electrolytic copper is accomplished by a three-step purification process. The first operation consists of an electrolysis through a purified CuS04-H2SO4 electrolyte using bagged anodes, low current .density (5 amp. per sq. ft.) and low temperature (25°C. max.). The electrolyte is prepared from commercial Cu2SO4 and is purified by heating the solution and adding I gram Fe as Fe 2(S04)3 to each 100 grams dissolved copper; sufficient hydrated oxide of copper, prepared from Cu2SO4 and NaOH, is supplied to precipitate Fe(OH)3, which carries down arsenic, antimony, tin, selenium, tellurium and other minor constituents. Silver and remaining traces of lead are removed by addition of Na2S to the acidified filtrate, which is then refiltered after standing hot overnight. The cold solution is made up to 30 grams per liter Cu and 150 grams per liter H2S04 and introduced without addition agents into the electrolytic system, which consists of a double row of hard-rubber battery boxes with the inside webbing and partitions removed, arranged in seven steps of ascending height. Electrolyte is uniformly supplied to the two highest cells by glass siphons operating from a constant-level reservoir, and flows by gravity through the bank of seven cells, entering each at the bottom and leaving at the top. Glass air lifts continuously supply the returning liquid to the constant-level reservoir for recirculation. Each cell contains three 434 by 43a by I-in anodes cast from high-quality electrolytic wire bar copper, various lots of which have been used with equal success. The anodes are pinned to sheet copper hangars shaped to prevent crawl of the electrolyte to the multiple-wired bus bars-which would result in fouling of the contacts and hang inside wool flannel bags stretched over open wood frames. The deposit

Jan 1, 1941

By T. Turner, C. L. Zimmerman, U. Kappus

The purpose of the project is to divert flood flows of North Potato Creek. The project is located in the southeast corner of Tennessee near Copperhill, approximately 160 km north of Atlanta, GA. The project consists of: a 28-m high dam, a 0.9-m diam outlet conduit, an emergency spillway, and a 4.0-m diam hard rock transbasin diversion tunnel. This flood-water management system was part of Cities Service Co. mine safety program for the Cherokee ore body, which is partially located within the creek channel. The following paper describes the entire project development from feasibility studies to design and construction management.

Jan 1, 1981

By F. E. Bachman

There is such a great variety of opinion concerning the best method of determining phosphorus in pig iron and steel, that a list of determinations, on a uniform sample of pig iron, together with a short description of the methods used by different chemists, and a few experiments on the accuracy of some of the methods used, [nay be of interest to members of the Institute. All the results given in List A are from the same lot of drillings, thoroughly mixed, except Nos. 8 and 9, and 28 to 32 inclusive, which are from the same pig, but were taken at a later period.

Jan 1, 1882

PURPOSE OF STUDY The case study was initiated because of the very real need to provide the best mineral inventory block estimates possible for the relatively new Sacaton mine. Sufficient mining had been done and records kept whereby it was possible to test the various estimation methods against detailed blasthole samples taken during mining. Three estimation methods were selected for testing: (1) the polygonal method, (2) the inverse distance squared method (IDS), and (3) the geostatistical kriging method. The results of the comparative analysis was thought to have very practical application to the selection of extension functions for future estimation of grade for mineral inventory blocks. GENERAL GEOLOGIC DESCRIPTION The porphyry copper deposit of the Sacaton open pit mine is related to small quartz monzonite intrusives of Laramide age which have been intruded into Precambrian granites. Both rock types act as host for the mineralization, which has been secondarily enriched sufficiently to constitute ore. The chalcocite enriched zone has been subjected to postenrichment oxidation processes with consequent partial destruction of the chalcocite blanket. Several mineralogical populations are represented in the total ore zone, but the blocks on the mine benches involved in the study were restricted to the top of the enriched zone. COMPUTATION OF MINERAL INVENTORY BLOCK ESTIMATES In order to make valid comparisons among the three estimation techniques, all of the inventories were prepared from diamond drill assay data used in the original engineering feasibility study. The data was taken from ex-

Jan 1, 1980

By J. E. Campbell, G. D. Calkins, N. M. Ewbank, M. Pobereskin, A. Wesner

GRINDING for size reduction affects the economics of many processes and products. It is essential as the first step in many industrial processes and is also a finishing step for materials with properties depending on particle size, such as talc, cement, and silica sand. Intermediate and fine grinding are vital operations in the U. S. cement industry, which is producing more than 250 million bbl of cement per year.' Wear of the grinding media is a large part of the grinding operation cost. Problems encountered in grinding cement are so complex that evaluation of efficiency and economy of grinding media is difficult.2 It has been especially difficult to evaluate the relative effectiveness of different types of balls because there are no good testing techniques. Many other industrial operations can be evaluated on a laboratory scale with reasonable accuracy. This does not hold true for evaluation of grinding balls. The consistent results obtained in a laboratory test under a given set of conditions are not always borne out in field application. Rough evaluations of the effectiveness of various compositions and types of grinding balls have been made in the field by using a full charge of one type in a mill and comparing the production record with another run using another type of ball. This method is time-consuming and not very precise, as the second run may not have been carried out under identical conditions. Laboratory-scale tests, on the other hand, have yielded inconclusive results, and many investigators have turned their attention to the development of a field testing technique. Field testing small sample lots of grinding balls has been impractical because it is difficult to identify and recover the test specimens from the grinding mill, and individual groups of balls that have undergone different heat treatments can not be separated.".4 To overcome these difficulties, previous investigators have identified the balls by distinctive marks, notches, and drilled holes, but this procedure has three serious drawbacks: 1) Grinding characteristics and quality of the steel balls may be affected. 2) Physical markings may be worn away in the grinding process, especially during a prolonged run. 3) Recovery from the bulk of the charge will be extremely difficult because the markings are hard to see and may be masked by a coating of the product. To circumvent these difficulties, a radioactive-tracer technique was proposed for recovery and separation of steel grinding balls and subsequent evaluation of the various compositions of the balls. The proposed technique involved five basic operations: 1) Thermal-neutron irradiation activation5 of each group of test grinding balls to a different level of specific radioactivity. 2) Addition of groups of radioactive steel-ball specimens into a ball tube mill. 3) Recovery of radioactive steel-ball specimens from the bulk of the mill charge. 4) Separation of the various groups by their specific radioactivity. 5) Evaluation of actual grinding ball wear. Before any physical tests were performed, required neutron irradiation intensity and time were calculated. Probable composition of the steels to be used was ascertained. An examination was made of the radioactive nuclides8 to be formed which would contribute measurably to the radiation level immediately after irradiation and during the test operation. The radioisotopes formed, their types of radiation, and their half lives are listed in Table I. Of these radioisotopes only iron-59 and chromium-51 were significant for the actual wear test. The intensity of radiation that could be detected by a Geiger counter when the test was completed was the basis for the minimum activation level established. The intensity of radiaton that could be safely handled at the beginning of the test was the basis for the maximum activation level, although this was not considered a major problem. Ten groups of grinding balls of various composition and/or surface or heat treatment were to be tested. One group was designated for the minimum irradiation time. The remaining groups were designated for irradiation periods that increased by increments of 33 pct from that of each preceding group. This difference was considered enough for separation and identification of the groups by comparison of specific activity. Potential Hazards: Possible radiation hazards that might be encountered during this experiment were evaluated for the three important phases: 1) the radiation hazard of placing balls and removing them from the mill, 2) contamination of the product cement by radioactive material worn from the balls, and 3) contamination of the steel by the radioactive balls left in the mill. The radiation intensity expected from the whole group of radioactive balls was calculated to be 250 milliroentgen per hr at 1 ft. This meant the balls would require special shielded packaging and warning labels on the shipping containers. In a radiation field of 250 mr per hr a man can work for 1 hr without exceeding maximum permissible weekly exposure. Since the balls could be dumped into the mill in a matter of seconds, relatively little radiation exposure was anticipated at this stage of the operation. If the weight loss in the balls was 7.7 pct per month and the cement feed through the mill was

Jan 1, 1958

By D. Collins, B. Pina, G. Snell

The conversion of moisture and ash free (maf) coal to pyridine solubles and gas was investigated in a microautoclave batch reactor. Two washed Kentucky coal samples (KY # 9 and KY #11) were studied in liquefaction solvents of various donor strength. The liquefaction solvent hydrogen donor strength was varied by changing the tetralin content of a mixed 1 -methylnaphthalene-tetralin mixture. Primary liquefaction conversions in excess of 90 wt% in 10 minutes of reaction time @ 700° K (427OC or 800°F) were achieved with liquefaction solvents of moderate donor strength, i.e. 40% tetralin. A modified irreversible first order rate expression (eq. 1) described the experimental data:

Jan 1, 1986

By W. J. Parton

The efficient recovery and preparation of small sizes of anthracite called No. 4 Buckwheat (3/32 by 1/32 in.) and No. 5 Buckwheat (1/32 in. by 0), pre-sent a difficult problem to the anthracite operators. In many instances preparation of these sizes, particularly No. 5 anthracite, is extremely inefficient. In many of the older preparation plants, inadequate facilities, and often none at all, were provided as an integral part of the plant for cleaning this fine anthracite. Consequently, much of the material smaller than 3/32 in. was discarded. As the demand for these sizes increased, facilities for preparing the fine sizes were often crowded into existing structures with consequent sacrifices of capacities and efficiency. In addition to this condition, the methods of preparing the finest sizes are being developed in an attempt to improve their efficiencies. Because the demand for small sizes of anthracite still is increasing, many operators would benefit by investigating and improving the cleaning equipment employed on these sizes. The object of this paper is to de- scribe a stationary screen device from which the underflow is restricted by orifices, called a launder screen, along with operating results of several applications of this screen; a settling tank in which two classified products are produced by the installation of a cylindrical partition of smaller diameter than the original tank, one product being recovered from the small tank created by the partition and one product from the space between the inner and outer tank walls; a small pocket classifier or hydraulic trap for use in removing high ash particles from a sludge flow; the classification or segregation of sludge solids occurring in a 16 in. diam pipe flow by analysis of samples procured at different zones; and the operating results of a Fahrenwald sizer, as well as the performance of the concentrating tables handling the classified products. These simple devices were employed at the collieries of the Lehigh Navigation Coal Company Incorporated, Lansford. Pa., in order to improve preparation results on the fine sizes of anthracite. Launder Screens The launder screen is a screening and dewatering device which probably could be used advantageously in the flow diagram of many fine coal plants. Fig 1 shows that it consists of a stationary screen constructed by placing 6 in. high partitions every 6 in. along a launder. Holes are then drilled on 6-in. centers across the bottom of the launder to receive pipe bushings of the desired diameter. The screen cloth is tacked on top of the partitions. When water and solids are fed to the screen, only a small portion of the total water is removed through the orifices in each compartment so that the water in the feed is distributed evenly over the whole length of the screen. The screening action which results is very efficient because the solids are kept in a fluid condition for the full length of the screen. Blinding of the screen can be minimized by the use of screen cloth

Jan 1, 1950

By John T. Galey

An intensified search for gas, because of the shortage in the area, led to the completion of 482 wells in southwestern Pennsylvania during 1944. This number was 27 more than the number in 1943, but 118 of the wells were nonproductive. Shallow Development Oil The initial production of the 25 producers completed was slightly less than was obtained from four wells above last yearJs total. The largest well, 20 bbl., was found in the Big Injun (Miss.) sand in Morris township, Washington County, at a depth of 2085 ft. It is currently producing about 3 bbl. per day. Outside the main producing area, a well drilled in Nicholson township, Fayette County, obtained 15 bbl. per day from 1864 to 1866 ft. in the Gantz (U. Dev.) sand. The Federal subsidy of 75¢ per barrel, effective , 1, 1944, which increased to $3.40 the current pipe-line price in this area, seems to have been insufficient stimulus to materially increase drilling for oil, although more repressuring operations are contemplated. Gas The volume of initial open flow of gas developed is off slightly over 10 million cu. ft. from 36 more wells than were completed a year ago, and the average rock pressure of this new gas is more than 100 lb. less than that obtained a year ago. Apparently the best find of this year was reported in Patton township, Allegheny County, where an initial volume of over 4 million cu. ft, was encountered in the Speechley (U. Dev.) sand at a depth of from 3293 to 3303 ft. The rock pressure there, 1190 lb. per sq. in., is nearly virgin. However, this area is fairly well delimited by dry holes and docs not seem nearly so promising from the standpoint of reserves as the Armbrust area, which was discovered several Years ago. In the patton township locality another fair well with 1303 M cu. ft. open flow and 400 lb. Per 59. in. rock pressure completed in the Hundred-Foot (U. Dev.) sand at a a depth of 2125 feet. Armstrong County, as usual, leads in number of producing wells completed with lowest percentage of failures but ranks only fou th in volume of production developed. Only two wells here had more than one million cubic feet capacity, but the rock pessure was under 200 Ib. Per sq. inch. In Fayette County, where the largest portion of new gas was found, activity appears to be shifting eastward. In Luzerne township, four producers having a total combined initial open flow in excess of 10 million cu, ft, were found in the Big Injun (Miss.) sand. The best well was found also in the same area in the Speechley sand (U. Dev.) at a depth of 3460 ft. This was a 2500-M CU. ft. well in Georges township. Several wells of more than a million cubic feet capacity were found in Jackson, Washington, Wayne and Whitley townships, Greene County. None of these, however, was in a new pool.

Jan 1, 1945

By W. T. lsbell

HERCULANEUM, MO., about thirty miles south of St. Louis on the Mississippi River, is the site of the lead smelter of the St. Joseph Lead Co. The lead concentrates come by rail from the Flat River district and from three properties in Madison County, Missouri; from the Balmat division in St. Lawrence County, New York; a small tonnage from the Tri-State district; and occasionally from the Aguilar property in Argentina. The average grade is 67 to 68 percent lead and 1 to 3 oz of silver. The bulk of the material is flotation concentrate, with some gravity or table concentrate. No secondary metals, outside drosses, or any materials high in bismuth, arsenic, or antimony are treated. All concentrate is received in box-caps and is unloaded directly from a trestle into the concentrate bins at the roaster plant. Flux, coke, and any miscellaneous lead-bearing material is either unloaded directly into bins or unloaded with a locomotive crane. All moving and switching of cars is done with two thirty-ton steam locomotives. Shipping facilities for the plant are provided by the Missouri-Illinois Railroad. Water for the plant and for fire protection is obtained from a dam built in a near-by creek. Drinking water both for plant and town is obtained from

Jan 1, 1947

By C. S. Trewin

ZINC, in its wrought form, is produced commercially in rolled strip, sheet, wire, rod and tubing. Wire has been made periodically, but due to the fact that slight drafts are necessary, the cost of production is greater than for the more common non-ferrous metals which are made into wire. Notwithstanding the cost, zinc wire has certain special uses for which it is particularly adaptable. Rod has been made both by rolling and extrusion; the product, however, has not indicated great commercial value. Tubing has been made from strip from time to time by forming a strip around a mandrel and either electrically or gas-welding a longitudinal joint. Recently a tube manufacturer has succeeded in making a fair quantity of this material. Its commercial adaptability is still to be determined but anyone who desires it can obtain quantities of the smaller sizes. Inasmuch as strip and sheet are commercially the most important, this paper will be devoted to these products. In the broader sense, zinc is not alloyed. That is, there are no combinations comparable to the various copper, aluminum and nickel alloys. It has been recognized for some time that the lead and cadmium occurring with commercial zinc have some effect on its properties and such alloys as may be said to exist are those made from zincs containing varying amounts of lead and cadmium with a relatively low iron content. The foreign rolled zinc will analyze higher in lead than the domestic grades. A representative foreign analysis will run 1.1 per cent. lead, 0.07 per cent. cadmium and 0.02 per cent. iron. The American grades vary from zinc approximating high grade and analyzing 0.08 per cent. lead, 0.002 per cent. cadmium and 0.015 per cent. iron, to the lower grades in which the lead will vary from 0.3 to 1.0 per cent., cadmium from 0.10 to 0.5 per cent. and the iron in the neighborhood of 0.02 percent. ROLLED ZINC Rolled zinc is produced in both the strip (or ribbon) form in which the product is rolled from a single bar in one continuous direction, or sheet in

Jan 1, 1928