Search Documents

By R. W. Raymond

This paper is simply a summary, prepared at the request of the Council of the Institute, of the report of Mr. Albert Ladd Colby, of South Bethlehem, Pa., presented at the New York meeting (October, 1896) of the Association of American SteelManufacturers, on " The Advisability of the Endorsement by the Association of the United States Standard Gauge, approved by Act of Congress, March 3, 1893, to the Exclusion of the Birmingham Gauge, the .Brown and Sharpe, and all Others:" a subject on which, at the Pittsburgh meeting (April, 1896) of the said Association, Mr. Colby had been appointed as a committee. The report favors the adoption, not of the United States standard gauge to the exclusion of others, but of a decimal system of gauging all materials in thousandths of an inch, thus doing away entirely with arbitrary gauge-numbers running in inverse order to the actual thickness. The American Institute of Mining Engineers originated this movement. The report of its committee on a standard wiregauge, presented in October, 1877,* recommended the abandonment of the system of fixed gauges for commercial use, and of the system of representing the diameters and sizes by numbers, and the adoption, in lieu thereof, of the system of expressing sizes in thousandths of an inch or fractions of a millimeter, and the use of the micrometer-gauge as a means of measuring sizes. In 1892 the American Society of Mechanical Engineers appointed a similar committee, and corresponding action was

Jan 1, 1898

By W. W. Tyler, A. C. Wilson, L. B. Nesbitt

INVESTIGATIONS of thermal conductivity and impact strength of the titanium alloy RC-130-B and 316 stainless steel were undertaken because of interest in strong, nonmagnetic, commercially available alloys of low thermal conductivity for use in low temperature experiments. Measurements of electrical resistivity and thermoelectric power were also made for some of the samples studied. The titanium alloy designated as RC-130-B is manufactured by Rem Cru Titanium Inc. It contains 0.14 pct C, 3.99 pct Al, and 4.7 pct Mn. A general discussion of properties of the two phase Ti-4Mn- 4A1 alloys is given by Finlay and Vordahl.' The alloy is machinable and has a yield strength greater than 130,000 lb per sq in. at 0.2 pct offset. The 316 stainless steel sample used for both conductivity and impact strength measurements was obtained from the Allegheny-Ludlum Steel Corp. and is designated as Allegheny metal 18-8M, Type 316, Grade 316. The sample had received 25 pct minimum final cold reduction and had a Brine11 hardness rating of 255. Several impact tests were made on a sample of 316 stainless which had not received the 25 pct cold reduction. Also several data points are reported giving thermal conductivity and electrical resistivity for a sample of 304 stainless steel taken from stock. Figs. 1 and 2 give thermal conductivity and electrical resistivity data for the titanium alloy and for

Jan 1, 1954

By Richard H. Zinszer

APPLICATION of electric logs has been used in correlation of subsurface structure to determine the size and shape of the oil reservoir. [ ] Such a knowledge is hardly complete until saturation and productivity are determined for the various horizons. It is difficult to use electric logs successfully for this purpose because of the many factors that influence the curves. In this work an effort was made to establish an empirical correlation between formation resistivity for a series of electric-log curves and water saturation and oil productivity of sand. Electric logs were obtained by recording with 10 different electrode spacings through the same interval of a well. In the analysis of these curves all factors except two, a dependent and independent variable, were held constant. The interval studied had been cored and a large number of samples were analyzed in the core laboratory in order to compare the values of permeability and saturation with the measured values of formation resistivity. Results of this analysis indicate: (I) the depth to which mud filtrate enters a sand body, (2) a correlation between permeability and sand resistivity for shallow penetration depths, and (3) that the water saturation for an oil sand can be determined from the measured sand resistivity after making suitable correc- [ ] tions for sand thickness. The proceduer in the last method depends on a correction for thickness factor and a theoretical curve. The accuracy of the theoretical curve is now being tested in the laboratory.

Jan 1, 1944

Professor Somasundaran has given an excellent presentation of the numerous problems which remain to be solved before the selective aggregation of fine particulates is likely to see broad commercial application in the beneficiation of mineral fines. However it is useful, I think, to reiterate some of the major problem areas. The over-riding factor which has limited the development of selective aggregation techniques is that processes such as coagulation and flocculation tend to be inherently non-selective. Conditions which favor the aggregation of one kind of fine particles usually favor the aggregation of all kinds of particles. As Professor Somasundaran has pointed out, the state of aggregation of a fine-particle dispersion is primarily determined by the forces of interaction between the individual particles. In most systems, the dominant forces are: 1. van der Waals - London Dispersion forces between the particles themselves 2. electrical double layer forces 3. steric forces between adsorbed layers on the surfaces of the particles. The London Dispersion forces between like particles are always attractive, but for dissimilar particles dispersed in a fluid medium can, in some cases, lead to a net repulsion. Electrical double layer forces always lead to repulsion between like particles but can, again, cause either attraction or repulsion for dissimilar materials. The steric forces, which are by far the least understood of the three types, can also lead to attraction or repulsion depending on condi-

Jan 1, 1979

By AIME AIME

IN ACCORDANCE with the provisions of the Rules of Procedure of the American Engineering Standards Committee, the American Society for Testing, Mate-. on Feb. 15, 1921, submitted for approval by the A. E. S. Committee certain Standard Specifications for Copper, all of which were adopted or in process prior to Jan. 1, 1920, and sent with the standards the following histories of development and statements of use. FOR SOFT OR ANNEALED COPPER WIRE (B3-15) These specifications were originaly adopted by. the American Society for Testing Materials in 1912. They were prepared by a committee of the Society designated as Committee B-1 on Copper Wire. The committee consisted of eleven members; representatives of five manufacturers of -copper wire, of four manufacturers of electrical apparatus, and of two firms of consulting and contracting engineers. The members of the committee were designated by the officials of the companies to act as their representatives in the committee.

Jan 1, 1921

By C. S. Trewin

Zinc, in its wrought form, is produced commercially in rolled strip, sheet, wire, rod and tubing. Wire has been made periodically, but due to the fact that slight drafts are necessary, the cost of production is greater than for the more common non-ferrous metals which are made into wire. Notwithstanding the cost, zinc wire has certain special uses for which it is particularly adaptable. Rod has been made both by rolling and extrusion; the product, however, has not indicated great commercial value. Tubing has been made from strip from time to time by forming a strip around a mandrel and either electrically or gas-welding a longitudinal joint. Recently a tube manufacturer has succeeded in making a fair quantity of this material. Its commercial adaptability is still to be dctcrmined but anyone who desires it can obtain quantities of the smaller sizes. Inasmuch as strip and sheet are commercially the most important, this paper will be devoted to these products. In the broader sense, zinc is not alloyed. That is, there are no combinations comparable to the various copper, aluminum and nickel alloys. It has been recognized for some time that the lead and cadmium occurring with commercial zinc have some effect on its properties and such alloys as may be said to exist are those made from zincs containing varying amounts of lead and cadmium with a relatively low iron content. The foreign rolled zinc will analyze higher in lead than the domestic grades. A representative foreign analysis will run 1.1 per cent. lead, 0.07 per cent. cadmium and 0.02 per cent. iron. The American grades vary from zinc approximating high grade and analyzing 0.08 per cent, lead, 0.002 per cent. cadmium and 0.015 per cent. iron, to the lower grades in which the lead will vary from 0.3 to 1.0 per cent., cadmium from 0.10 to 0.5 per cent. and the iron in the neighborhood of 0.02 percent. Rolled Zinc Rolled zinc is produced in both the strip (or ribbon) form in which the product is rolled from a single bar in one continuous direction, or sheet in

By R. W. Guard, M. E. Fine

By treating the dislocation like a surface and ap-plying the usual thermodynamic treatment to the adsorption process a Gibbs adsorption equation for dislocations was derived. For extended dislocations in binary solutions the adsorbed concentration on the fault, X2a, may be computed from (jo/da2b) where a2b is the activity of the solute in the bulk material and s is the stacking-fault energy. Using the data of Howie and Swann for s the adsorption concentration goes through a maximum at 2 at. pct Al in Ag-Al, 10 at. pct Zn in Cu-Zn, and 8 at. pct A1 in Cu-Al. The pinning stress calculated from this concentration difference goes Ihrough a maximum at the same concentration us the peak in X2 a. The computed pinning stress thus does not vary with composition in the manner predicted by Suzuki, as was also pointed out by Hendrickson. The results are compared with the stress increment which can be attributed to Suzuki locking in Cu-Zn and Cu-Al stress-strain curves. They both agree in magnitude and in the location of the maximum. The predicted and observed maximum values for the Cu-Zn system (where activity data are available) are 700 g per sq mm (predicted) and 1000 g per sq mm (measured, laking into account the orientation factor of 2.2 to convert poly-crystalline to single-crystal data). CERTAIN simple internal surfaces may be regarded as dislocation grids. This fact suggested that it might be profitable to consider certain phenomena related to segregation of solute atoms at dislocations from the point of view of the thermodynamics of surfaces and surface adsorption. A general treatment of this type is given and then the results are applied to Suzuki segregation and pinning. Confirmation of the results is obtained from comparison of stress-strain behavior for copper and copper-base alloys. Two kinds of dislocations need be treated: perfect and extended dislocations. In either case the line tension of a dislocation, ?. the work which must be done to increase the length of dislocation by a unit length, is analogous to the surface tension. For an undissociated dislocation ? is the self-energy of a unit length of dislocation; for an extended dislocation where is the self-energy per unit length of a pair of partials far enough apart so that there is no interaction energy, is the interaction energy per unit length, is the stacking fault energy per unit area, and w is the equilibrium separation of the paired partials. In the absence of an applied stress the force pushing the dislocation partials apart in a close-packed structure is Gb2/12p where G is the shear modulus, b is the Burgers' vector of the complete dislocation, and is the separation of the partials. At the equilibrium separation, w this force equals s. Thus

Jan 1, 1965

By Myron Rodgers

IN rock- or ore-crushing tests all data, in order to be valuable for study and comparison, should be obtained and tabulated under conditions as uniform as possible. The results of many such tests have no value for comparison, because of incomplete data and the lack of uniform conditions, screens and scale of sizing, etc. The purpose of this paper is to suggest a form of standard specifications which may be developed by the Milling Committee and approved by the A. I. M. E. for rock-crushing tests. It is not intended to discuss any theories of rock crushing. Reports of rock-crushing tests should include the following details: 1. Description of the machine employed (jaw or gyratory crushers, rolls, stamps, tube mills, Chilean mills, etc.). 2. Method and material (timber, concrete, etc.) of foundation. Much power is dissipated in the vibration of poor foundations. 3. Locality from which the rock or ore was obtained, and geological, mineralogical, and physical characters of the material. 4. The power consumption of the machine running with no load and with full load, the unit of power being 1 hp, per 24 hr. 5. The capacity of the machine in tons (of 2000 lb.) per 24 hr. 6. The duty in tons per horsepower-day. 7. The screen analysis of feed and product by the proposed A. I. M. E. standard screen scale. On the foregoing statement, the following remarks are offered.

Jan 9, 1915

By H. W. Schadler

Single crystals of tungsten, which were grown by electron bombardment floating zone refining, were strained 2 pet in tension and bending at 298°, 77°, and 20°K to determine the modes and crystallography of the plastic deformation of these temperatures. At 77° and 20°K plastic deformation occurs by slip on systems of the type (011) [111] and by twinning on (112)-type planes. For crystals strained at 298°K, deformation occurs by slip in [111] directions on either (Oil)- or (112)-type planes. CURRENT models for the initiation of brittle fracture in crystalline materials are based on a knowledge of the details of their plastic deformation.1 Body-centered cubic tungsten exhibits brittle failure at temperatures below about 500 °K yet the modes and crystallography of its plastic deformation have not been studied below 1000°K. In 1924, Goucher2 reported that tungsten single crystals with a total impurity content of less than 0.01 wt pet deformed by slip on the (112) [111] system in the temperature range 1000° to 3000°K. He also observed (001) [010] slip in one crystal which was constrained by the presence of a large fissure. According to Barrett3 tungsten also deforms by twinning on the (112) plane in the [111] direction, but he gives no details on the tendency for twin formation or the temperature range in which twinning occurs. Therefore, as a necessary part of a study of the factors influencing the brittle fracture of tungsten, the modes and crystallography of the plastic deformation were determined at 298°, 77°, and 20°K. Tungsten single crystals, grown using the electron-bombardment zone-refining technique first described by Calverly,4 were deformed to between 1 and 2 pet plastic strain in tension and bending. The surface offset resulting from slip or twinning was observed with an optical microscope to determine the crystallography of the deformation. The existence of twins was proven by the standard polishing and etching technique; and the crystallography of dislocation motion was followed using the dislocation etchant described by Wolff.5 Some observations on the fracture characteristics of tungsten single crystals are included. EXPERIMENTAL TECHNIQUES Growth, Purity, and Perfection of the Crystals-Several years ago Calverly, Davis, and Lever4 dem-onstrated the feasibility of growing tungsten single crystals by the electron-bombardment floating zone-refining technique, and Carlson6 showed that crystals produced in this way had a high degree of purity and were ductile at room temperature. Tungsten single crystals produced by this technique in equipment similar to that described by Carlson were used in this study. The starting material, a powder metallurgy product, was obtained in the form of a swaged 1/8-in. rod from the General Electric Wire Plant in Cleveland, Ohio. The crystals were grown from this material in a vacuum of 10"4 mm of Hg by passing a molten zone 1/8 in. long down the rod twice at a speed of 3 mm per min. At this zone speed

Jan 1, 1961

By Robert Maes, Robert de Strycker

The Cu-Sn-As systeM was studied in the region near the Cu-42 and (214-As binary diagrams, where reactions in the solid state appear, resulting from the decomposition of the y(Cu-Sn) phase and from the formation of the 7 phase (Cu,As). The techniques used were microscopic observation, thermal analysis by dilatometry, and X-vay diffraction. The formation of the 7 phase gives rise to a ternavy pevitectoid veaction; the decomposition of the y phase gives rise to five transitional reactions. The temperatures of almost all these reactions could be determined; in the most favorable cases , the accuracy of this determination was of 11.5-C. The 7 phase is stabilized by tin additions, the arsenic atoms being replaced by tin atoms up to 35 pct; this has allowed the preparation of pure j) phase and the confirmation, by extrapolation, of the conrposition of this compound in the Cu-As diagram. In the first part of this work, the solidification reactions in the Cu-Sn-As phase diagram were studied. In the copper corner, the structure of the alloys presented the evidence of reactions in the solid state: on the one hand, all the alloys containing the y phase of the Cu-Sn diagram showed, under the microscope, that this phase had formed different decomposition products after complete solidification; on the other hand, the appearance of the 7 phase of the Cu-As diagram necessitated the introduction of a peritectoid formation reaction. The study of the decomposition of the y phase has been done by preparing about forty alloys that were homogeneous y at high temperature. The formation of the 7 phase has been studied by means of a few alloys with a composition near the homogeneity field of this phase at room temperature. The part of the Cu-Sn phase diagram of interest for this study is represented by Fig. 1, with the phase designation which will be used in the remainder of this paper; it is drawn after Hansen and Anderko.' The Cu-As diagram has already been presented in Part I of this work; the significant features of this study are the existence of the arsenides CusAs and Cu5Asz, and the formation of a compound CUEAS, designated as the 7 phase, by a peritectoid reaction at about 325°C. EXPERIMENTAL METHODS The fundamental technique for the investigation of this part of the Cu-Sn-As constitution diagram was microscopic observation; the greatest part of the observed alloys has also been subjected to thermal analysis by dilatometry; a few selected alloys have then undergone an X-ray analysis by powder diffraction. Alloy Preparation. The alloys were prepared from the same products as in Part I of this study: cathode copper, arsenic with a purity better than 99.5, and tin with a purity of 99.98. The fusion of the ternary alloys was realized from

Jan 1, 1967

By R. A. Cunningham, A. S. Murray

If a dense fluid such as mud or water is used for circulation, the formation drilled is influenced by a hydrostatic pressure. This pressure depends on hole depth arid drilling fluid density. Laboratory tests indicute that drilling rates in many forri~ations are decreased with increased pressure,—in some cases as much as 90 per cent. A comparison between laboratory and field tests indicates that drilling fluid head affects drilling rates in the field approximately the, same as in the laboratory. Drillirrg rates of many formations are increased by reducing drilling fluid head. INTRODUCTION For many years it has been noted that field and laboratory drilling rate tests did not agree even when the formations tested were the same. For instance, tests of some shales by the Hughes Tool Co. laboratory indicated drilling rates approximately 20 to 30 ft/hour, whereas in the ground this shale would drill only 3 to 5 ft/hour. A possible reason for this discrepancy is the effect of the high pressure which the drilling fluid exerts against the formation at the bottom of the hole. Consider a small element of rock (Fig. II that is to be removed by a rock bit. If the hole is filled with mud or water. the upper surface of the rock element is subjected to a pressure which depends on hole depth and fluid density. The mass of earth around this rock element presses against the circumferential surface and the lower surface. Because of the probability of shearing stresses between the rock element and the surrounding rock, this element is not under true hydrostatic stress. However, as a first approximation for test purposes the rock element was assumed to he under hydrostatic stress. The effect of hydrostatic pressure on some physical properties of rock has been studied.1,2,3 These tests show that the "differential" compres-sive stress:': necessary to cause rup- ture in rock cylinders is greater when tested under high hydrostatic pressure than when tested under atmospheric conditions. These tests were made with pressures greater than 20,000 psi which is in excess of those normally encountered in oil well drilling. Similar tests were made by the Bureau of Reclamation' using pressures equivalent to those encountered in oil well drilling. Again the "differential" compressive stress necessary to produce failure increased with increasing hydrostatic pressure. These tests indicated that drilling rates would probably decrease. Correlation between these tests and drilling tests was not practical. The purpose of this work is to study the effect of mud column pressure on drilling rate, assuming that the material drilled is in a state of hydrostatic strcss. This problem was initially investigated in the laboratory using variable bit loads and confining pressure;. Confirmation of laboratory results was obtained in the field from a series of carefully controlled drilling tests. Because of the necessity of testing many different types of formations. only results from representative formations will be presented here.

Jan 1, 1956

By George S. Rice

INTERESTING developments going on in European coal mines look to: (1) increasing mechanization; 12) concentration of mining; (3) improvement in safety appliances; and (4) studies in bettering roof supports and. incident to this, studies of the way a roof behaves under different conditions of support and methods of mining and back-filling. Mechanization and concentration off mining is being adapted to a considerable extent in Great Britain coincident with the development of conveyors. Belt conveyors, shaker-pan conveyors, and a combination of the two are used. For pitching seams not steep enough for the coal to run in station-chutes, the. shaker-pan conveyor is more popular. For large outputs from a contiguous face, the double-unit system of face layout-that is, the conveyors meeting at a common point-is favored.

Jan 1, 1934

By D. H. Bacon

Our Transactions contain so many suggestions of apparently trivial, yet really important, contrivances for the saving of time and

Jan 1, 1893

By Paul M. Tyler

MARKETWISE the year 1935 was rather a good one for most of the rare and minor metals; as a class they climbed out of the depression much faster than the common metals. The diamond market, too, was better than it had been for years, attributable only in part to investment buying, as there was a genuine pick-up in consumer demand. Wars and rumors of war tended to speed up purchases of certain metals, but consumption for peaceful purposes was the principal factor. Significant was the important role played by new industrial uses. New discoveries during the year were disappointingly few, considering the broad extent of this research frontier. Scientific developments were far from being at a stand-still, of course, but the dominant note was the cashing in on research consummated in former years. With even a moderate upturn in general business a surprising number of laboratory ideas donned overalls and found jobs in industry.

Jan 1, 1936

By H. R. Ogden, A. G. Imgram, D. N. Williams

The effects of composition on the mechanical properties and aging characteristics of several alloys in the Ti-V-Cr system, with and without aluminum modifications, were evaluated. Increasing the chromium, vandium, or aluminum content increased the strength of quenched structures with chromium being the most effective strengthener. Appreciable aging response was obtained with low chromium alloys, but high chromium alloys age softened rather than. hardened. High vanadium contents had a similar effect. Aluminum additions shifted the aging behavior toward that observed in lower chromium alloys, enabling high chromium alloys to be age hardened. DURING the course of titanium alloy development many a and a-ß alloys have been evolved to commercial status. However, only one all-ß alloy has achieved this same stature. This is the Ti-13V-11Cr-3Al alloy. It is characterized by a very sluggish ß-phase decomposition reaction such that very slow cooling rates can retain the 0 phase at room temperature. In addition, very high strength levels can be obtained by long-time aging treatments. Combinations of cold or warm working followed by aging produce even further improvements in strength. This paper describes the results of a research program in which the effects of composition on the mechanical properties and aging characteristics of several alloys in the Ti-V-Cr system, with and without aluminum modifications, were evaluated. EXPERIMENTAL PROCEDURES Electrolytically refined, high-purity titanium was used as the alloy base for these studies. Iodide chromium, electrolytically refined vanadium granules, and high-purity aluminum sheet were used as alloying additions. The compositions of interest were melted as 250-g ingots in a direct current arc melting furnace under a flowing atmosphere of argon. The ingots were hot forged to 3/4-in.-diam bars, vacuum annealed for 6 hr at 1800°F to reduce residual hydrogen content, and then hot swaged to 1/4-in.-diam rods. Fabrication history, and interstitial analyses after fabrication are given in Table I. All specimens to be heat treated were sealed in Vycor capsules under a partial pressure of argon. Samples used to define the ß transus were quenched from temperatures ranging from 1350° to 1100°F after holding at temperature for 15 min. Samples for aging studies were quenched from above the ß transus temperature and then aged for up to 64 hr at 750°F and for 100 hr at 850°, 900°, and 950°F. The effects of straining prior to aging were also investigated. The results of these studies were used to select the heat treatments for the tensile specimen blanks. Heat treatments of the tensile specimens are described in Table 11. Alloys were aged after solution heat treatment or after solution heat treatment and cold swaging to 50 pct reduction in area. Standard 0.125-in.-diam tensile specimens were machined from the heat-treated blanks. All tensile tests were performed in a Baldwin-Southwark uni-

Jan 1, 1963

By C. Williams, D. V. Carter

During 1943 five oil fields and two gas-condensate fields were discovered in the East and East Central Texas district. The New Hope field, discovered by Tide Water-Seaboard in Franklin County, is the most important oil discovery since the Hawkins field in 1940. At the close of the year two oil sands were producing and two additional oil sands were being tested. The gas-condensate fields of Appleby in Nacog-doches County and the Stewards Mill field in Freestone County had only one producing well each. The Carthage field was extended 3 miles north and 4 miles west. Another well that was testing at the year end indicated a probable eastward extension of several miles. The Quitman field, in Wood County, was the most active from the standpoint of drilling operations. Approximately 48 wells were complcted during the year. The second and third most active fields were Hawkins field, Wood County, and Kildare field, Cass County, respectively. Wartime restrictions of material, together with manpower shortage and Federal spacing regulations, reduced the number of oil and gas-well completions from 265 in I942 to 171 in 1943. This represents a drop of 35 percent, or approximately 1/3, enough to replace the 531 producing wells abandoned in the district during the year. No changes were made in the price of crude oil in the district in 1943. The district produced 177,652,940 bbl. of condensate and oil during 1943. This represents an increase of approximately 11 per cent compared with the previous year. The East Texas field, which is the largest and most important field in the district, had an annual production of 128,568,647 bbl. of oil, which is approximately 6.5 per cent more than the previous year, and represents 72 per cent of the district's production of condensate and oil for the year. The district had an estimated basic daily allowable of approximately 509,000 bbl. of oil on Dec. 31, 1943. The entire district produced approximately 30 pcr cent of the state's production for the year 1943. The Hawkins field, Wood County, was operated 271 days during the year and with an average daily production of approximately 52,488 bbl. for the year. This field, which is the second largest in the district, produced 14,224,164 bbl, of oil during the year. Changes in annual production in certain fields in the district can be attributed to their ability to produce at higher rates, the demand, and transportation facilities in the war effort. The East Texas field showed an over-all decrease in reservoir pressure of 8.30 lb. during the year. Indications were that through the first quarter of 1944 the return of salt water to the reservoir was having a beneficial effect. It is hoped that, as more and more water is returned to the reser-

Jan 1, 1944

By D. V. Carter, C. Williams

During 1943 five oil fields and two gas-condensate fields were discovered in the East and East Central Texas district. The New Hope field, discovered by Tide Water-Seaboard in Franklin County, is the most important oil discovery since the Hawkins field in 1940. At the close of the year two oil sands were producing and two additional oil sands were being tested. The gas-condensate fields of Appleby in Nacog-doches County and the Stewards Mill field in Freestone County had only one producing well each. The Carthage field was extended 3 miles north and 4 miles west. Another well that was testing at the year end indicated a probable eastward extension of several miles. The Quitman field, in Wood County, was the most active from the standpoint of drilling operations. Approximately 48 wells were complcted during the year. The second and third most active fields were Hawkins field, Wood County, and Kildare field, Cass County, respectively. Wartime restrictions of material, together with manpower shortage and Federal spacing regulations, reduced the number of oil and gas-well completions from 265 in I942 to 171 in 1943. This represents a drop of 35 percent, or approximately 1/3, enough to replace the 531 producing wells abandoned in the district during the year. No changes were made in the price of crude oil in the district in 1943. The district produced 177,652,940 bbl. of condensate and oil during 1943. This represents an increase of approximately 11 per cent compared with the previous year. The East Texas field, which is the largest and most important field in the district, had an annual production of 128,568,647 bbl. of oil, which is approximately 6.5 per cent more than the previous year, and represents 72 per cent of the district's production of condensate and oil for the year. The district had an estimated basic daily allowable of approximately 509,000 bbl. of oil on Dec. 31, 1943. The entire district produced approximately 30 pcr cent of the state's production for the year 1943. The Hawkins field, Wood County, was operated 271 days during the year and with an average daily production of approximately 52,488 bbl. for the year. This field, which is the second largest in the district, produced 14,224,164 bbl, of oil during the year. Changes in annual production in certain fields in the district can be attributed to their ability to produce at higher rates, the demand, and transportation facilities in the war effort. The East Texas field showed an over-all decrease in reservoir pressure of 8.30 lb. during the year. Indications were that through the first quarter of 1944 the return of salt water to the reservoir was having a beneficial effect. It is hoped that, as more and more water is returned to the reser-

Jan 1, 1944

By Hsun Hu

Direct observations were made on the recrystalli-zntion of a cold-rolled (110) [001] crystal of 3 pct Si-Fe by annealing thin sections of the specimen inside the electron microscope during examination. Subgrain formation, presumably by polygonization, occurs rapidly, followed by a slow increase in the subgrain size before recrystallization can be detected. No migration of the subgrain boundaries was observed, and the formation of recrystallization nuclei by coalescence of subgrains is suggested. Re-c~ystallization characteristics of various texture components were individually examined. AS reported in a previous paper: orientations of the various deformation texture components in a 70 pct cold-rolled (110) [0011 crystal of 3 pct Si-Fe were completely confirmed by transmission electron diffraction patterns taken at various areas of the specimen. These orientations can be summarized as follows: Over most areas of the deformed crystal (111) planes are parallel to the surface. These areas correspond to either $- the two main defor: mation textures, the (111) [112] or the (111) [112].2-5 Within a few areas, (100) planes parallel to the surface are frequently found. These areas represent the minor deformation texture component, the (100) [Oll] type, which is derived from rotated Neumann bands.2'4'5 Only in very rare instances are (110) planes found parallel to the surface. This orientation corresponds to the very weak texture component of the (110) [001] type. In a pole figure, this (110) [0011 orientation is located within the orientation spread between the two main (111) [1121 type textures. Usually the electron diffraction patterns taken at various areas of the specimen are very simple ones, i.e., for any one area the pattern consists only of sharply defined spots of a single orientation. In some areas, however, more or less continuous rings of weaker intensities are superimposed on a simple pattern, indicating the presence of a wide range of additional orientations. In order to understand in detail the recrystallization of this cold-worked crystal, the recrywtallization characteristics of each of the various deformation texture components must be examined. This can best be done by using a high-temperature stage and transmission electron microscopy techniques, whereby small areas corresponding to the various texture components can be selected individually for examination. The present paper presents results obtained by this method. MATERIAL AND METHOD Specimens were prepared from a previously studied1 single crystal of a commercial grade 3 pct Si-Fe alloy with an initial orientation (110) [00l], cold-rolled 70 pct from 0.014 in. to 0.004 in. in thickness. Thin foils were prepared by electrolytic polishing as described in the earlier paper.' Specimens of this thin foil were then mounted in a high temperature stage similar to the one designed by Whelan.6 A direct current was used as the heating source. The temperature of the heating grid was calibrated by means of a Pt vs Pt-10 pct Rh thermocouple in a vacuum chamber (0.01 to 0.02µHg). Maximum variation within the temperature range of 250o to 000°C was about ± 25°C. After the desired areas were selected for examination, the specimen was heated to a low temperature for some time while the selected area was constantly watched. When no further change in structure and orientation could be observed, a higher temperature was applied. Photomicrographs and diffraction patterns were taken from time to time during examination, with the heater temporarily turned off* while the photographs were

Jan 1, 1962

By Burnham E. Field

The chemical industry is constantly looking for new materials which either are more resistant to corrosion than those now available or have improved physical properties to meet the requirements of higher temperatures and greater pressures. Attack by acids is one of the more important forms of corrosion and in the last few years the development of acid-resistant alloys has been quite rapid. Perhaps the most notable example is that of nitric acid, the problem of which has largely been solved by the chromium-iron and chromium-iron-nickel alloys. Sulfuric acid may be handled in lead, iron, or the iron-silicon alloys, depending on conditions. As to hydrochloric acid, no metal or alloy can be called entirely satisfactory for handling this acid under plant conditions.' The results of our investigations on the resistance of the nickel-molybdenum alloys to hydrochloric acid have been confirmed by those of Guertler, Rohn, Schulz, Jenge, and others12 but thus far only one such alloy has approached commercial production in Germany; this contains approximately 15 per cent. chromium and 7 per cent. molybdenum with the remainder chiefly nickel. Dr. S. W. Parr, as far back as 1914, developed a complex alloy known as "illium," with a nickel base and containing some molybdenum. 3 Dr. Parr was primarily interested in an alloy for lining bomb calorimeters, and while illium does show good resistance to acid it is too expensive for general use. Two United States

Jan 1, 1929

By Burnham E. Field

The chemical industry is constantly looking for new materials which either are more resistant to corrosion than those now available or have improved physical properties to meet the requirements of higher temperatures and greater pressures. Attack by acids is one of the more important forms of corrosion and in the last few years the development of acid-resistant alloys has been quite rapid. Perhaps the most notable example is that of nitric acid, the problem of which has largely been solved by the chromium-iron and chromium-iron-nickel alloys. Sulfuric acid may be handled in lead, iron, or the iron-silicon alloys, depending on conditions. As to hydrochloric acid, no metal or alloy can be called entirely satisfactory for handling this acid under plant conditions.' The results of our investigations on the resistance of the nickel-molybdenum alloys to hydrochloric acid have been confirmed by those of Guertler, Rohn, Schulz, Jenge, and others12 but thus far only one such alloy has approached commercial production in Germany; this contains approximately 15 per cent. chromium and 7 per cent. molybdenum with the remainder chiefly nickel. Dr. S. W. Parr, as far back as 1914, developed a complex alloy known as "illium," with a nickel base and containing some molybdenum. 3 Dr. Parr was primarily interested in an alloy for lining bomb calorimeters, and while illium does show good resistance to acid it is too expensive for general use. Two United States

Jan 1, 1929