Search Documents

By E. W. Greene, J. B. Duke

This paper deals with the application of froth flotation techniques to the beneficiation of kaolin clay and phosphate slimes, two very fine particle sized materials. The kaolin problem involves the removal of a small amount of a contaminating mineral (anatase), while the phosphate problem involves the concentration and recovery of a much larger percentage of apatite. Due to these differences, and also different response to flotation, the two problems are discussed in separate parts of the article. An idea of what is meant by "Ultrafine Minerals Or Slimes" as used in the title can be had by an examination of Fig. 1. Particle size distributions are presented for a crude kaolin clay, a coarse fraction and a fine fraction. The crude kaolin as mined was blunged with water, degritted through a 325-mesh Tyler screen, and dispersed with sodium silicate. The dispersed crude was then centrifuged in the laboratory into the coarse and fine fractions shown in the figure. The distribution curves were obtained by the well known sedimentation technique of Casa-grande1 using a long arm centrifuge to obtain equiva- lent spherical diameters down to 0.2 p on the finer fraction. Fig. 1 shows the coarse fraction kaolin to be 50% finer than 3 p, while the crude kaolin is 509 f'lner than 1.4 p, and the fine fraction 50% finer than 0.46~. For comparison 53 p on the horizontal scale would represent Stokesian diameters which would just pass a 325-mesh Tyler screen, taking into consideration the Andreasen sieve correction factor of 1.22 times the screen opening. 2 Another helpful comparison is the surface areas, which in square meters per gram, are 0.044 for 53 p particles, 0.77 for 3p, 1.65 for 1.4 p and 5.0 for 0.46 p particles. Fig. 2 is an electron micrograph of a similar fine fraction kaolin showing the hexagonal plate-like particle shapes.

Jan 1, 1962

By Charles Bohdanowicz

The accompanying tables' show that in 1936 production of crude oil in Poland decreased very slightly (Tables 1 and 5), by about 1 per cent, and that gas production increased by about 11 per cent. As in preceding years, drilling (Tables 1, 2 and 3) was devoted principally to extension of oil fields in the Jaslo district (fields 1, 5 and 7) and, in a lesser degree, of those in the Stanislaw6w district (field 27). Production of crude oil is being sustained in a large measure by the deepening of old wells; besides a total number of 183 new wells completed (Table 3) about 152 wells were deepened, and in a general way the results of deepening were better than those of new wells drilled. Reserves of "proved land" have not increased as far as crude oil is concerned, but a notable extension of gas fieldsZ was attained in Daszawa (field 25) and in the Roztoki area (field 5). In the sub-carpathian zone gas fields have been proved in the vicinity of Kalusz, Kos6wJ and in the northwestern sector of that zone, between Tarnow and Lezajsk. The gas horizons of Daszawa occur in the Upper Tortonian, those of Kos6w in the Lower Tortonian (Middle Miocene). Exploratory drilling has been performed near Kalusz, and has been commenced near Kos6w and in the Tarn6w area. The Kos6w gas approaches the "wet" type. A possible gas reserve with a volume of 4,000,000,000 cu. m. (141,000,-000,000 cu. ft.) has been calculated, for an area of about 5 sq. km. of the Daszawa field, on the basis of production obtained and of decreases in pressure and their distribution. The fields of Roztoki and Strachocina (No. 12) have not yet supplied sufficient data for a calculation of reserves, which might possibly be estimated at 2,000,000,000 cu, m. (70,000,-000,000 cu. ft.).

Jan 1, 1937

By M. MacFarland, E. McAuliffe

Our North American railway system, including the lines serving the United States, Canada and Mexico, with a total operating mileage of 303,040, employing 71,818 locomotives, represents not only the greatest industrial user of fuel coal, but in the variety of coals used, ranging from anthracite down through the several gradations of bitumirlous coals, as well as lignites, covers about all there is in American-mined coals. Necessarily the wide range of fuel coal embraces not only extremes of calorific value but also every possible gradation shown in size and preparation, from run of mine to washed nut and slack. Approximately 8 per cent. of the fuel used by the railroads is consumed in shop power plants, shop buildings, pumping stations, station buildings, etc. The principal class of coal (as designated) used by the railroads is bituminous, such, however, including a substantial tonnage of subbituminous and lignite coal; all United States railroads using in 1923 for locomotive, shop, station buildings and miscellaneous uses, a total of 4,578,000 tons of anthracite, 155,795,000 tons of bituminous, subbituminous and lignite coal and 58,005,000 bbl. (42 gal.) of fuel oil. The Class 1 railroads of the United States (those whose gross annual earnings equal or exceed $1,000,000) used in 1926: Bituminous, subbituminous and lignite coal, net tons..... 140,083,885 Anthracite, net tons................................ 3,667,505 Fuel oil, gal........................................ 3,058,915,511 Railroad fuel-purchasing agents rarely attempt to classify coal for locomotive use on the basis of chemical analysis; although this is very generally used as a guide in the initial selection of a fuel supply. The extraordinarily high rate of combustion developed in the modern locomotive, generating as high as 2500 b.hp., with limited facilities for cleaning fires en route, suggests the importance of a fuel supply containing a reasonably low percentage of ash-making material, and while the percentage of locomotive coal handled through automatic stokers is growing, the principal tonnage is yet fired by hand.

Jan 1, 1930

By Arthur Phillips, Carl H. Samans

The study of anisotropy in metals has been greatly stimulated in recent years by the rapid development of X-ray methods for determining the crystallographic relationships of wrought and annealed materials. Prior to this time the knowledge regarding the directional properties of commercial alloys consisted almost exclusively of observations of a practical nature made during the fabrication of metal objects, supplemented by a limited number of mechanical tests on specimens cut at various angles to the direction of working. Such observations clearly indicate that the common methods of cold-working metals cause both a crystallographic and a mechanical fibering varying in character and degree according to the nature and extent of the deforming process. Even after annealing, following certain not too well known combinations of reductions and anneals, a preferred orientation may exist,, thereby constituting a residual fiber effect sufficiently pronounced to manifest directional properties. With the application of the X-ray the experimental horizon was extended chiefly because the study of anisotropic metals promised to offer direct and quantitative evidence regarding the involved mechanism of fragmentation and plastic flow. As a natural consequence the intensive studies in this direction have yielded a vast accumulation of data of ultimate potential value. Unfortunately, however, as is commonly the case in entering a virgin field of experimentation, many of the data cannot be molded into complete and coherent form because of the many unrelated conditions of the experimental projects. Again, the results of the study of single crystals have been rather naturally but at times indiscriminately applied to poly crystalline metals. Furthermore, sweeping statements have been made regarding the behavior during working and annealing of metals and alloys, entirely on the basis of similarity in lattice arrangement. There is abundant reason for believing that relatively small concentration variables, differences in magnitude and distribution of applied stresses, and the character of associated annealing treatments may in some cases greatly influence the mechanics of flow

Jan 1, 1933

By C. P. Melloy

INTRODUCTION Ventilation practice at Isa Mine has been evolving since underground mining began in 1931. Much fundamental work has been conducted and reported regarding the primary ventilation system [Mathews K.E. et a1 (1967) and Brown J.R., Fisher T.H., Gibson K.L. (1979) 1. However, ventilation networks for subsystems such as open stopes, have evolved with experience. This paper outlines current ventilation practice for open stoping. Mount Isa Mine The mine is located in semi-arid North-West Queensland, Australia, and currently produces 20 000 tonnes of copper ore and 10 000 tonnes of silver-lead-zinc ore daily in each five day working week. Mining extends over a north-south strike length of 3.5 km with a maximum width across dip approaching 1 km, and is to a depth of 960 m (Figure 1). At present approximately 90% of the mine's copper production is from the 1100 Orebody, which contains ore reserves of 121 million tonnes of 3.2% copper. Open stoping is currently the mining method employed, and is used for primary stoping and pillar recovery adjacent to cement fill walls. The development of stoping methods in the 1100 Orebody has been documented by Kirkby R.W., Blair J.R., and Hutton R.C. (19781, Hornsby B. and Sullivan B.J. (1978), and Alexander E.G. and Fabjanczyk M.W (1981). As many as thirteen open stopes may be producing concurrently in the Orebody (Figure 2). The multiple silver-lead-zinc orebodies containing reserves of 54 million tonnes of 150 g/t silver, 6.4% lead and 6.5% zinc, are mined by open stoping, and cut and fill techniques. These methods have been documented by Goddard I.A. and Bridges M.C. (1977 1, and Goddard I. A. (1981 1. Only the ventilation of the 1100 Orebody open stopes will be discussed. However, the same ventilation philosophy is employed in open stope design in the lead orebodies.

Jan 1, 1981

By J. J. Reed

The mines of southeast Missouri's Lead Belt have been in operation since 1864, almost 100 years. During this period about 10 pct of the total ore available has been left in place as pillars, and this now represents the best ore reserve left to the older mines. St. Joseph Lead Co. has been investigating various plans of pillar recovery for several years. The example to be described is only one possible approach under a specific set of conditions. Conditions vary greatly in the different areas within the Lead Belt, and the same approach would be entirely inadequate in certain other areas, but there are important sections where this system is clearly applicable. Horizon mining is practiced in the Lead Belt, and stopes may vary from 10 ft to well over 100 ft high. Fig. 1 is a plan view of 6100 stope, the area to be discussed. For these mines this is a small stope, only 10 to 12 ft high. Before any plans were drawn up for pillar recovery, three independent estimates of the pillar grades were made by the mine superintendent, the mine captain, and the mine geologist. After these results were averaged, pillars indicated to be of economic grade were marked for removal as shown. At this stage several alternatives were considered: 1) retreat with caving, 2) concrete replacement pillars, and 3) systematic bolting and retreat. A retreating system with caving was not chosen because the roof was known to be too bad even to permit loading a blasted pillar before caving would begin. Concrete replacement pillars would have been too costly and would have required a large crew, bulky materials, and unwieldy equipment. Systematic bolting was chosen as being most acceptable for the following reasons: 1) Limited area and spans were involved. 2) Only minor modifications to the jumbo would be required for bolting. 3) Only a two-man bolting crew would be needed. 4) Only compact bolting materials would be required. 5) The bolting plan could be modified to allow

Jan 1, 1960

By S. H. Ash

Mass production methods, although increasingly important for economic reasons, create new hazards, remove many hazards, and improve health and safety by reducing exposure and obtaining better supervision. Such methods must be efficient or be discarded. Skilled workmen are required who must be trained to utilize equipment that replaces picks, shovels, and explosives. The effects of working conditions on the health of workmen have long been evaluated in noncoal mines. Studies and action programs relating to environmental health hazards in the mineral industry have placed particular emphasis on dusts. The anthracite industry is conducting an action program on the problem of dust. Segments of the bituminous industry are now conducting similar investigations. An industrial hygiene survey of coal mining in the State of Washington has been conducted and the results published in 1949. (State of Washington, Department of Health, I. H. Bul letin 4.) Chest X rays were obtained from miners in the six major coal-producing counties. State Health Department mobile X-ray equipment was set up at most large mines. Participation was on a voluntary basis, and response was obtained from 70 percent. Important in successful mining safety programs are training programs for supervisors and workmen alike. These programs recognize that the employe is the focal point in injury prevention and are planned and function around him. During the war, industries had to compete with each other for workers and to obtain and hold good workers, working conditions had to be made attractive. The average age of the mine worker increased, and, contrary to what many expected, mining injury rates decreased rather than increased. To attract competent workers, risks to life and limb, as well as laborious tasks, have to be reduced, and an experienced worker is indispensable for safety. Young men are returning to modernized mines. Mass production methods and equipment are more to their liking; jobs are more remunerative, demand action, and require special training and skill that give them the mark of a craftsman. Such workmen can be taught safe methods.

Jan 1, 1950

By A. English, M. J. Greaves

This paper is a discussion of pelletizing systems developed over the last 15 to 20 years for the agglomeration of fine iron ore concentrates. Five different pelletizing systems are now in commercial use in the U.S., and for the purposes of comparison, estimated operating costs and capital costs for the construction of four of them are included. Capacities of existing commercial plants are examined, together with the anticipated capabilities of plants presently being built or projected. In just 21 years, the art of pelletizing iron ore concentrates has reached maturity with mastery of the separation of finely divided concentrates from low-grade iron ores and their agglomeration into pellets containing about 65% iron. This accomplishment has firmly established an improved feed for the blast furnace, with resulting benefits in faster reduction of burdens and greater economy of operation. The present production capacity of pelletizing facilities in the U.S. is about 20 million tons annually, and it is expected to double by 1970. The rapid expansion of pelletizing in the U. S. has been closely observed in European countries, notably in Sweden and Germany, where pioneer agglomerating techniques were developed early in this century. PELLETIZING PLANTS AND PROCESSES Twelve commercial pelletizing plants are presently in operation in the U. S. and Canada. An equal number are in various stages of engineering and construction, and many others are being considered. The pelletizing systems currently employed include shaft furnaces, horizontal grates using three different airflow arrangements, and grate kilns. The capacity of pelletizing operations in North America is shown in Table I. All of these plants are integrated with the mine, the ore-crushing facilities and the concentrating plant and are equipped with storage and loading-out facilities for the product. Normally, a pelletizing plant is composed of a shuttle conveyor above the receiving bins; balling equipment; a heat-hardening system including the necessary auxiliaries such as furnaces, burners and controls, ducts, fans, meters and instrumentation; fines recovery equipment; and product handling equipment. Also included are the necessary auxiliaries and utilities such as boilers or power plant; oil unloading and storage facilities; coal unloading storage, grinding and distribution facilities; and bentonite or other additive storage and distribution equipment. Shaft Furnaces: Vertical shaft furnaces used in this country are limited to the treatment of natural magnetite concentrates containing minor quantities of residual fluxing elements. Fig. 1 shows a perspective view of the shaft furnace with balling, feeding and pellet-handling equipment. An elevation of a shaft furnace is shown in Fig. 2. A commercial shaft furnace unit is about 45 ft in height with a 6 x 14-ft rectangular cross section and has a nominal production rate of approximately 50 gross tons of pellets per hour. The upper portion of the furnace shaft is constructed of fire brick as protection from the high process temperatures involved. The lower portion of the shaft is lined with abrasion-resistant brick to withstand erosion from the fired pellets. Rectangular-shaped, refractory-lined and insulated combustion chambers are situated on each side of the shaft furnace. Oil or gas is burned to produce high temperature gases which are forced into the furnace through ports located near the top of the combustion chambers. The shaft furnaces operate at a pressure of approximately 6 psi. Pellets are fed into the top of the furnace by a pantographic feeder designed to produce the desired pellet stockline. The furnace is kept filled at all times and pellets are fed and discharged from the furnace at the same rate. In early development, 10 to 12 lb of solid fuel was incorporated in the pellets. However, the main source of process heat is now derived from the combustion chamber gases. In some instances no solid fuel is used. The pellet movement in the shaft furnace is counter-current to the flow of gases. Ambient air is introduced through louvers at the lower end of the furnace, at about 6 psi, cooling the fired pellets and supplementing the heat of the high temperature gases from the combustion chamber ports. The zone of maximum temperature, located above the ports of the combus-

Jan 1, 1963

By Lyden, Joseph P.

THE Picher Mining Field, fig. 1, which lies between Baxter Springs, Kansas, and Commerce, Okla., is the most intensely mineralized and the largest zinc-lead ore producing area in the Tri-State District of Missouri, Kansas, and Oklahoma. It has a vast lateral extent of underground workings that is unequaled for the observation of the geology of zinc-lead ore bodies in sedimentary horizons; and thousands of churn drill holes in the unmined areas supplement the underground observations with useful data for the interpretation of the geology. This paper is confined to the ore deposits of the Picher mining field. The reader is referred to the bibliography for the general geology of the Tri-State district which has been ably covered by many geologists. The writer was co-author of several publications on the Tri-State district.- This paper is necessarily a repetition of parts of those publications but contains a few changes and additions on the deposition of the minerals. The parts of this paper concerning mineralization maps and pipe slump-structures are not covered in the above publications.

Jan 1, 1950

By L. L. McDaniel

Copper smelters of various kinds have operated in the Morenci district since 1872, but all have been abandoned with the exception of the present Morenci Smelter of Phelps Dodge Corporation, which was completed in 1942. During the five-year period starting in 1937, the Morenci ore body was prepared for open pit mining, pilot mill test work was carried out, and a complete reduction works, of which the Smelter is a part, was designed and erected. Actual construction work on the Morenci Smelter was started in the fall of 1940, and warming up of the units began on April 1, 1942. Charging of the reverberatory furnaces commenced on April 18, 1942, and the first anode copper was produced on April 26, 1942. The smelter was originally designed to handle the production of the Morenci Concentrator on a 25,000 ton per day program, but by the time the smelter was in operation, plans were already underway to increase the smelter capacity to handle the production of the concentrator which was being enlarged to 45,000 tons a day capacity as a war-time necessity. This extension to the smelter was completed and the new units were put in operation toward the beginning of 1944. The original smelter consisted of a smelter crushing plant, bedding plant, two direct-smelting reverberatory furnaces with two waste-heat boilers on each furnace, three converters, an anode department, a stack, and all of the usual accessory smelting equipment. The extension consisted of increasing the bedding plant from three to five beds, the reverberatory department from two to four furnaces, and from four to eight waste-heat boilers, and the converter department from three to six converters. A third converter aisle crane was added and additions were made to the flue systems and conveyor systems throughout the smelter; but no change was made in the smelter crushing plant or the anode department, and the same stack was used for all additional Smelter units. A blister casting machine was installed at that time in the south end of the converter aisle to handle excess and emergency production above the capacity of the anode department and in 1947 a converter aisle skull breaker and a lime burning plant were added as the final units for a complete plant. The choice of direct smelting over calcine smelting for the Morenci Smelter was made after careful study by members of the Western organization of Phelps Dodge Corporation and after test runs on direct smelting of Morenci concentrate had been made at the Douglas Smelter of Phelps Dodge Corporation. The Morenci furnace charge is made up of comparatively high grade concentrate with no ores of smelting grade available and with only flux, a small amount of copper precipitate and the usual amount of smelter secondaries to be smelted with the concentrate. The simplicity of direct smelting for this charge and the large amount of waste-heat steam available from direct smelting operations were factors influencing the decision to adopt direct smelting for Morenci. The design of the Morenci Smelter and the type of units selected followed best experience at the Douglas Smelter of Phelps Dodge Corporation. A description of the original smelter before operations started was given in an article in the May 1942 issue of Mining and Metallurgy. The purpose of the present article is to describe the enlarged Morenci Smelter, with a discussion of metallurgy and operating practice and to show tabulations of operating and metallurgical results obtained. Because of beginning operations during the early years of World War 11, many problems caused by labor shortage were encountered, but no major difficulties developed in starting the new plant. However, because of labor shortage, full scale Smelter production was not reached until the fall of 1946. Fig 1 shows a general plan of the Morenci Reduction Works. The arrangement of the smelter equipment is shown in Fig 2, a sectional view of the smelter is shown in Fig 3, and the smelter flow sheet is shown in Fig 4. Metallurgy The metallurgy of direct smelting, being more or less fixed by the character of the charge, is not subject to the control available in calcine smelting. Slags may be modified by the addition of suitable fluxes, but the grade of the matte is determined almost entirely by the iron:copper ratio of the concentrate. The direct smelting operation involves distributing the wet concentrate along the sidewalls and in the bath of a reverberatory furnace by means of some suitable feeding device and raising the temperature of the charge so that first the moisture is driven off, then the first-atom sulphur is eliminated, and finally the sulphide portion of the charge melts and runs into the bath, carrying with it the non-sulphide portion which has been partially fluxed to form a suitable slag. The fusion of the non-sulphide portion is completed by contact with the irony converter slag which is regularly being poured into the reverberatory furnace. The smelting rate of the charge is influenced by the mineralogi-cal composition of the sulphide portion of the concentrate and by the composition and amount of the non-sulphide portion including the fluxes added. The copper in Morenci concentrate is chiefly in the form of chalcocite, intimately associated with pyrite, and non-sulphide content is very low so that

Jan 1, 1950

By L. D. Frink

Those actively interested in mining are fully aware of the ever-increasing difficulty of making conditions such that efficient work can be done in underground openings, especially as higher rock temperatures are encountered in depth. This is also true where an effort is being made to cut down the burden of overhead expense by working headings 24 hr. in a day if blasting is done as often as is possible in that time. That the conditions resulting from both these causes have driven the native-born Americans from the mines and that their places have been taken by less efficient foreigners is a fact that we must all admit. The great war now being fought in Europe and the educational qualification clause written into our immigration law by the last Congress will probably limit very materially the supply of labor, such as we are now using in our mines, and will force upon mine operators the necessity of making this work appeal again to Americans. Metal tubing, with blower or exhaust fans, has long been used in supplying air to dead ends where natural ventilation is impossible, or in driving the smoke from such places, or in doing both, as the need might be. Here in Butte we have now come to use canvas tubing very extensively and find that it has many advantages not possessed by the metal. The use of flexible tubing is not new, but it has not been generally used in mining operations. Recent improvements, however, in the canvas itself and in the jointing of sections and manner of suspension have so increased its usefulness that it promises to add much to the efficiency of mining. There is now on the market a product that is impervious to air, is fireproof, and has a system of jointing which permits it to be put up or taken down in a few seconds. In this article an effort will be made to explain the manner in which canvas tubing is being used in the North Butte company's operations at Butte, Mont. The accompanying photographs will, I hope, help make clear what may be done with this material.

Jan 1, 1918

By L. A. Morley, W. T. Parry

Engineering design problems encountered by mining engineers often depend on the properties of natural granular materials such as soil, poorly consolidated sediment, fault gouge, and hydrothermally produced clay. The physical properties of such granular materials frequently are determined by the properties of silicate clays. In most mining applications, the clays are in contact with water. Swelling of clay due to water infiltration can interfere with underground support and haulage systems. Water-saturated clay on fault, fracture, and bedding planes causes slope failures in open pit mines, roof falls and heaving of weak underclays in coal mines. Water may be removed and cementing agents may be produced in clays by electrical methods. When an electrical potential gradient is applied to a charged capillary by two electrodes, water moves toward the negative electrode.1 This electrokinetic phenomena is known as electroosmosis and has been used to successfully dewater clay minerals which lack strength because of water. A consolidation effect occurs when the flow of water is accompanied by a decrease in water content. Electrochemical changes in the clay result in cementing and irreversible hardening. Theory A mathematical basis of electroosmotic phenomena is presented by Helmholtz.3 Smoluchowski5 modifies Helmholtz’ model and presents Eq. 1 to describe fluid flow velocity due to electroosmosis. For this formula, the zeta potential can be measured experimentally. The Helmholtz-Smoluchowski model is reasonably valid for clay aggregates with large pores saturated with fresh water or dilute electrolyte solutions.° An assumption used for Eq. 1 (equations are given Table 1; terms are defined in Table 2) is that the thickness of the electrical double layer surrounding the clay particles is small compared with the pore radii. Because this is generally not the case, Schmid7 presents Eq. 2. The volume charge density in the pore may be approximated from cation exchange capacity and porosity measurements. Casagrande8 offers a semi-empirical relationship (Eq. 3) for volume rate of electroosmotic flow and finds that k, is relatively constant for most clays with an average

Jan 1, 1972

26. G. H. S. Price, S. V. Williams, and G. J.O. Garrard: Heavy alloy, its production. properties and uses. Metal Industry (1941) 599 354s 372. 394. 27. R. Kieffer and W. Hotop: p. 320 of ref 12. 28. F. R. Hensel. E. I. Larsen, and E. F. Swazy: Physical properties of metal compositions with a refractory metal base. Chap. 42, 483, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 29. R. Kieffer and W. Hotop: p. 290 of ref. 12. 30. H. Freundlich: Kapillarchemie. 211 (1923) Leipzig. 31. W. Ostwald: Zisch. f. Phys. Chemie. (1900) 34, 503. 32. G. A. Hulett: Zisch. f. Phys. Chemie. (1901) 37. 385; and (1904) 47, 357. 33. J C. Chaston: Discussion to Price, Smithells and Williams, p. 257 of ref. 4. 34. W. Dawihl: Untersuchungen ueber die Vorgaenge bei der Abnuetzung von Hartmetallwerkzeugen. Ztsch. f. techn. Phys. (1940) 21 336. 35. W. Dawihl and J. Hinnueber: Ueber den Aufbau der Hartmetallegierungen. Kol-loidzlsch. (1943) 104, 233. 36. F. Skaupy: Dispersoidchemische und verwandte Gesichtspunkte bei Sinter-hartmetallen. Kolloidzlsch. (1942) 98, 92; and (1943) 102, 269. 37. F. C. Kellcy: Cemented tantalum car- bide tools. Trans. ASST (1932) 19, 233. 38. E. W. Engle: Cemented carbides. Chap. 39, 436, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 39. W. Dawihl: Zlsch. f. Melallkunde. (1940) 32, 320. 40. P. M. McKenna: Tool Materials (Ce- mented Carbides). Chap. 40. 454. Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 41. G. A. Meerson. G. L. Sverev, B. Y. Osinovskaja: Zhurnal Prikladnoi Khimii. (1930) 139 66. 42. A. G. Metcalfe: The mutual solid solubility of Tunesten Carbide and Titanium carbide- Metal Trealmenl (1946) 13, 127. 43. P. Schwarzkopf: Powder Metallurgy. 196-201 and 354-356 (1947) New York. 44. H. Burden: The manipulation and sintering of hard-metals. Special Rep. No. 38, p. 78. Iron and Steel Inst.. 1947. London. 45. W. D. Jones: Principles of powder metal- lurgy. 150. (1937) London. 46. J. E. Drapeau: Sintering of powdered copper-tin mixtures. Chap. 32. 332, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 47. H. E. Hall: Sintering of copper and tin powder. Metals and Alloys (1939) 10, 297. 48. F. Sauerwald: Present status of powder metallurgy. -.Melallwirlschafl. (1941) 20, 649. 671. 49. H. L. Wain: Powder metallurgy; influence of some processing variables on the properties of sintered bronze. Report ACA-25. Australian Council for Aeronautics (1946) Melbourne. 50. S. L. Hoyt: Constitution of copper-tin alloys. Metals Handhook, 1364. (1939) Cleveland. 51. T. Ishikawa: Studies on the interdiffusion of copper, tin and graphite powders. Nippon Kinzoku Gakkai-Si (1937) I, 226. 52. A. Carter and A. G. Metcalfe. The struc- ture of porous bronze bearings. Special Rep. No. 38, p. 99. Iron and Stecl Inst. (1947) London. 53. R. P. Koehring: Sintering atmospheres for production purposes. Chap. 25, 278. Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 54. C. G. Goetzel: Some properties of sintcred and hotpressed copper tin compacts. Trans. AIME (1945) 161, 569. 55. J. W. Lennox: The production of some non ferrous engineering components by powder metallurgy. Special Rep. No. 38. p. 174. Iron and Steel Inst., 1947, London. . P. Duwez and H. E. Martens: The power metallurgy of porous metals and alloys having a controlled porosity. TP 2343, Metals Tech. April 1948. This volume. p. 848. 57. E. A. Owen and L. Pickup: X-ray study of the interdiffusion of copper and zinc. Proc. Royal Soc., London, Series A. (1935) 149, 283. 58. C. G. Goetzel: Sintered and hotpressed compacts of copper-zinc powder. Chap. 34. 352, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 98, R. Chadwick. E. R. Broadfield, and S. F. Pugh: Observations on the pressing. sintering, and properties of iron-copper powder mixtures. Special Rep. No. 38, p. 151, Iron and Steel Inst. (1947) London. 60. A. Squire: The properties of iron-copper compacts. Watertown Arsenal Lab. Rep. WAL No. 67101. 61. F. C. Kelley: Properties of sintered iron- comer uowder. Iron Age (Aug. 15. 193) 158 57. 62. G. H. Howe: Sinterinn of Alnico. Iron Age (Jan. 11. 1940) 14.5, 27. 63. R. Kieffer and W. Hotop: p. 359 of ref. 12. 64. W. Hotop: Permanent magnets from sintered iron-nickel-aluminum. Stahl und Eisen (1941) 61, 1105. 65. P. R. Kalischer: Some experiments in the production of aluminum-nickel-iron alloys by powder metallurgy. Trans. AIME (1941) 145, 369. 66. S. J. Garvin: Production of sintered per- manent magnets. Special Rep. NO. 38. p. 67. Iron and Steel Inst. 1947, London. 67. F. C. Kelley: Discussion to P. R. Kalischer. p. 375 of ref. 65. 68. R. Kieffer and W. Hotop: p. 357 of ret, 12. 69. C. H. Howe: Sintered alnico. Chapter 48, 530, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. Powder Metallurgy Seminar (C. G. Goetzel presiding) C. G. Goetzel—The seminar has been opened by a man who has been active in the field for over fourteen years and has made, since then, some major contributions to the advancement of the art. After having been associated with the Moraine Products Division of General Motors Corporation for over ten

Jan 1, 1949

By John H. Hearding

Induction heating, together with automatically controlled tempering and hardening is giving Oliver faster and more accurate bit sharpening, while experiments with bit taper promise to offer increased footage per bit.

Jan 10, 1953

By Arthur Phillips

THE study of anisotropy in metals has been greatly stimulated in recent years by the rapid development of X-ray methods for determining the crystallographic relationships of wrought and annealed materials. Prior to this time the knowledge regarding the directional properties of commercial alloys consisted almost exclusively of observations of a practical nature made during the fabrication of metal objects, supplemented by a limited number of mechanical tests on specimens cut at various angles to the direction of working. Such observations clearly indicate that the common methods of cold-working metals cause both a crystallographic and a mechanical fibering varying in character and degree according to the nature and extent of the deforming process. Even after annealing, following certain not too well known combinations of reductions and anneals, a preferred orientation may exist, thereby constituting a residual fiber effect sufficiently pronounced to manifest directional properties. With the application of the X-ray the experimental horizon was extended chiefly because the study of anisotropic metals promised to offer direct and quantitative evidence regarding the involved mechanism of fragmentation and plastic flow. As a natural consequence the intensive studies in this direction have yielded a vast accumulation of data of ultimate potential value. Unfortunately, however, as is commonly the case in entering a virgin field of experimentation, many of the data cannot be molded into complete and coherent form because of the many unrelated conditions of the experimental projects. Again, the results of the study of single crystals have been rather naturally but at times indiscriminately applied to polycrystalline metals. Furthermore, sweeping statements have been made regarding the behavior during working and annealing of metals and alloys, entirely on the basis of similarity in lattice arrangement. There is abundant reason for believing that relatively small concentration variables, differences, in magnitude and distribution of applied stresses, and the character of associated annealing treatments may in some cases greatly influence the mechanics of flow and consequently largely determine the final structural characteristics of the metal.

Jan 1, 1932

By J. F. Crouch

INTRODUCTION Roll front uranium has unique geologic characteristics (L,) which require specialized mining procedures. Roll front uranium occurs in arkosic sandstones with the ore zone typically less than 100 feet in thickness with up to 400 feet of overburden. The areal extent of ore is often a few thousand acres. Within the ore zone, ore grade material occurs in C and S shaped rolls, which are a few feet in width and height but may run laterally for several hundred feet. Since the total mine plan may include mining all ore, a roll front uranium mine may cover a few thousand acres. For both economic and environmental reasons, a roll front deposit is mined as a series of phases or sub-pits (3, 4) as illustrated in Figure 1. A typical sub-pit is 400 to 500 feet across. Sub-pit 1 is stripped initially and the overburden is spoiled on the surface. Depending on haul distance and overburden characteristics, stripping is done with trucks and shovels (or front-end loaders) or scrapers. When ore is encountered in sub-pit 1, mining begins, and the stripping equipment is moved to sub-pit 2, with sub-pit 2 overburden also being spoiled on the surface. When ore is encountered in sub- pit 2, sub-pit 1 mining should ideally be complete so the mining equipment can move to sub-pit 2 and sub-pit 3 overburden can be spoiled in the mined out sub-pit 1 area. Ore is mined selectively in a series of 12 to 24 inch cuts by a 2-1/2 yard backhoe on the basis of radiometric probing. For effective drainage, ditches must be maintained on the boundary of sub-pits, and mining lifts are kept as level as possible, with the orebody slightly elevated as part of general good mining practice. Waste removal in the ore zone is done by self- loading scrapers near the orebodies and by push-pull or push loaded scrapers away from the orebodies. Each self-loading scraper cut is

Jan 1, 1983

The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties. United Engineering Trustees, Inc. When Mr. Carnegie made his gift which made possible a home for the engineering societies, a separate corporation was organized to act as a holding company and to manage the common property. This was long known as the United Engineering Society, but the name has now been changed. to one which more nearly reflects the real function of the corporation. It holds title to the Engineering Societies Building and to various funds placed in its charge and is managed by a Board of Trustees, of which three are chosen by each of the four societies, American Institute of Mining and Metallurgical Engineers, American Society of Mechanical Engineers, American Institute of Electrical Engineers and American Society of Civil Engineers, which have equal and undivided interests in the property. The land and building cost two million dollars. During the gear 1934, the constitution and By-laws of The United Engineering Trustees, Inc., were thoroughly revised and a better organization of its functions was affected: The Engineering Foundation and the Engineering Societies Library were made "departments? of the United

Jan 1, 1936

By E. F. La Vigne

ON Aug. 10, 1884, the Retsof Mining Co. began the sinking of an 18 by 12-ft. shaft at Retsof, N. Y. Rock salt was reached in 1885, in September, at 1008 ft. below the surface. The first salt was shipped in the fall of 1885. A timber breaker was built in 1886. In July, 1895, there was a consolidation of the Retsof Mining Co., the Greigsville Salt & Mining Co., the Livonia Salt Co., and the Lehigh Salt & Mining Co. These consolidated salt companies are now known as the Retsof Mining Co., a subsidiary of the International Salt Co. Eventually all of the mines were closed except the mine of the Retsof Mining Co., at Retsof, Livingston County, New York. On July 6, 1921, about ½ mile south of the original shaft and plant of the Retsof Mining Co., a new 9 by 28-ft. concrete-lined shaft was started. The shaft is 1063 ft. deep from the top of the shaft collar to the bottom of the salt bed. At the same time a reinforced-concrete breaker and other buildings were erected. This new plant began opera-tions on Dec. 15, 1923. It was designed for a capacity of 3000 tons in 8 hours.

Jan 1, 1936

By A. R. Kinkel

The Shasta copper-zinc district of northern California lies in the foothills of the Klamath Mountains at the northern end of the Sacramento Valley. It contains two main areas of base-metal ore deposits, the East Shasta and West Shasta districts shown in Fig. 1. The East Shasta includes the area from the Afterthought mine, near the settlement of Ingot on U. S. highway 299 East, to the Bully Hill mine, on the north side of the Pit River, 9 miles to the north- west. The West Shasta, a well-defined northeast- trending district about 8 miles long and 2 miles wide, west of the Sacramento River, Fig. 2, is the western part of the ore-bearing area formerly known as the Shasta copper belt. Referred to in the older writings as a copper arc, this belt was thought to form a crescent extending entirely around the head of the Sacramento Valley, the convex side to the north. Recent studies by the U. S. Geological Survey in cooperation with the California State Division of Mines show that there are two districts, one at each end of the so-called copper arc, which are distinct in geologic structure and ore occurrences, and that there is only sporadic and unconnected copper mineralization between them.

Jan 2, 1955

GENTLEMEN : Herewith are transmitted the reports of your Treasurer and the Chairmen of your standing committees on Admissions, Membership, Papers and Publications, and Library for the calendar year 1931. To these reports you are referred for further details of the year's activities. Finances.-Depressed industrial conditions prevailing throughout the year were reflected in a substantial decline in current revenue. Aside from interest on sundry special funds (but including that from the Life Membership, Library, and General Reserve Funds) total receipts amounted to $168,274, compared with $194,636 in 1930. The principal items of decrease were $17,000 in advertising income from the monthly magazine MINING AND METALLURGY, and about $9,600 in dues and initiation fees. Of this shrinkage $4,000 is accounted for by decrease in the number of new members enrolled; and $5,600 by diminished income from current dues and arrearages. This naturally has coincided with an \ increase in delinquency and "drops" or suspensions for nonpayment of dues. The decline in advertising income, amounting to 38 per cent as compared with that of 1930, in general paralleled the experience of all technical and trade publications; and it is problematical whether 1932 will show as large a return from advertising as did 1931.

Jan 1, 1932